N7ZDAZ8811FDOCSIS CABLE MODEM

User’s Manual Page 1 U U s s e e r r ’ ’ s s M M a a n n u u a a l l User’s Manual Page 2 Introduction Congratulations on Your Purchase! Your new DOCSIS Cable Modem will provide you with high-speed access to the Internet through your cable TV (CATV) network - access at a fraction of the time it takes traditional telephone modems. In addition, your service will be always connected. Those two features give you the information you want, when you want it ... and your telephone line is kept free. Important Rules for Safe Operation In addition to the careful attention devoted to quality standards in the manufacture of your TurboComm DOCSIS Cable Modem, safety is a major factor in the design of every product. However, safety is your responsibility, too. This section lists important information that will help assure your enjoyment and proper use of the TurboComm Cable Modem and accessory equipment. Please read them carefully before operating and using your modem. User’s Manual Page 3 Installation Read and Follow Instructions - You should read all the safety and operating instructions before operating the modem. Follow all operating instructions. Retain Instructions - You should save all the safety and operating instructions, for your future reference. Heed Warnings - Comply with all warnings on the products and in the operating instructions. Check Power Sources - Operate this product only from the type of power source indicated on the product's marking label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. Be Careful of Overloading - Do not overload wall outlets or extension cords, as this can result in a risk of fire or electric shock. Overloaded AC outlets, extension cords, frayed power cords, damaged or cracked wire insulation, and broken plugs are dangerous. They may result in a shock or fire hazard. Periodically examine the cord, and, if its appearance indicates damage or deteriorated insulation, have it replaced by your service technician. Protect Power Cords - Route power supply cords so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords where they are attached to plugs and convenience receptacles, and examine the point where they exit from the product. Check Ventilation - Slots and openings in the enclosure are provided for ventilation to ensure reliable operation of the product and to protect it from overheating. Do not block or cover these openings. Never block these openings by placing the product on a bed, sofa, rug, or other similar surface. Never place this product near or over a radiator or heat register, or any other heat source (including amplifiers). Do not place this product in a built-in installation, such as a bookcase or equipment rack, unless you provide proper ventilation. Do Not Use Accessories - Do not use attachments, unless they are recommended by TurboComm, as they may cause electrical or fire hazards. Use the Recommended AC Adaptor - You must use the Adaptor that comes with your TurboComm Cable Modem. Do Not Use Near Water - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool, and the like. Do Not Place Near High Temperature Source -for example near a steamer, Kitchen range fire, and the like. Use Caution in Mounting This Product - Do not place this product on an unstable surface or support. The product may fall, causing serious injury to a child or adult, as well as serious damage to the product. Use Care in Moving Product-and-Cart Combinations - Quick stops, excessive, force and uneven surfaces may cause the product-and-cart combination to overturn. User’s Manual Page 4 Ground the Cable System - Be sure that the outside cable system is grounded, so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984 (Section 54 of the Canadian Electrical Code, Part 1) provides information with respect to proper grounding of the cable system. Do not disconnect RF cable from your TurboComm Cable Modem while the power to your modem is on. Use Unplug Power Before Cleaning - Do not use liquid cleaner or aerosol cleaner. Use a damp cloth for cleaning. Keep Objects Out of Openings - Never push objects of any kind into this product through openings, as they may touch dangerous voltage or "short-out" parts, which could result in a fire or electric shock. Never spill liquid on the product. Protect From Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet, and disconnect the cable system. This will prevent damage to the product due to lightning and power line surges. Take at least 10 seconds between DC plug off and on. Service Do Not Remove Covers - Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Unplug this product from the wall outlet carefully, as the AC adaptor may be hot. Refer Servicing to Qualified Service Personnel Under the Conditions Listed Below When the power supply cord or plug is damaged. If liquid has been spilled or objects have fallen into the product. If the product has been exposed to rain or water. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions. If the product has been dropped or the cabinet has been damaged. When the product exhibits a distinct change in performance, such as the inability to perform basic functions - this indicates a need for service. User’s Manual Page 5 Require Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform sa…

Text truncated - open the document above for the full version.

Block diagram of External cable modem Tuner PHY Chip MAC Chip Micro- Controller Static RAM FLASH EEPROM Ethernet Chip 10BaseT Ethernet 75 Ohm COAX Static RAM Power Supply +12V AC/DC Power Convertor (External) AC POWER

4F-2, #171, Sung-Teh, Rd., Taipei, Taiwan Tel:+886-2-2759-8868 Fax:+886-2-2759-8869 MESSERS: Max Light Technology Co.,Ltd DATE: 03 /24/2000 POWER OF ATTORNEY SUBJECT: FCC APPLICATION We, the undersigned, hereby authorize Max Light Technology Co.,Ltd. To act on our behalf in all matters relating to application for equipment authorization of our model: DAZ8811F including the signing of all documents relating to these matters. Any and all acts carried out by Max Light Technology Co.,Ltd. On our behalf shall have the same effect as acts of our own. Applicant: TURBOCOMM TECH.INC. By: MR. LOBO CHANG Signature Printed Title: Manager

MAX LIGHT Report Number: MLT0003P15001 FCC ID: N7ZDAZ8811F Technology Lab MAX LIGHT Report Number: MLT0003P15001 FCC ID: N7ZDAZ8811F Technology Lab MAX LIGHT Report Number: MLT0003P15001 FCC ID: N7ZDAZ8811F Technology Lab MAX LIGHT Report Number: MLT0003P15001 FCC ID: N7ZDAZ8811F Technology Lab MAX LIGHT Report Number: MLT0003P15001 FCC ID: N7ZDAZ8811F Technology Lab MAX LIGHT Report Number: MLT0003P15001 FCC ID: N7ZDAZ8811F Technology Lab MAX LIGHT Report Number: MLT0003P15001 FCC ID: N7ZDAZ8811F Technology Lab

MAX LIGHT Report Number: MLT0003P15001 FCC ID: N7ZDAZ8811F Technology Lab Label Format: Label Position: This device complies with Part15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) This device must accept any interference received ,including. Interference that may cause undesired operation. Model: DAZ8811F FCC ID: N7ZDAZ8811F MADE IN TAIWAN Equipment Lable 4cmX2.5cm Rear View

8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 DD CC BB AA PCX1.SCHX2 PCX CABLE MODEM VER 6.1 TURBONET COMMUNICATIONS INC B 113Monday, February 14, 2000 Title SizeDocument NumberRev Date:Sheet of Power Supply PCX2 Downstream RF PCX3 RF_AGC IF_AGC TUNER_UPST_IF TUNER_SCL TUNER_SDA IF_OUT+ IF_OUT- Libit 4030 PCX5 DATA[7..0] IF_IN+ IF_IN- A[9..2] /RD /WR /CS /RESET PROFILE[2..0] TXCLK TXSTRT /TXEN TXDATA[7..0] RF_AGC IF_AGC PGA_DATA PGA_CLK /PGA_DATAEN /PGA_PD UPST_IF_OUT+ UPST_IF_OUT- /TXFULL TXERR MDCLK FSYNC INCORR DVALID MDOUT[7..0] LBT_TXEN Strong ARM PCX7 D[31..0] /WAIT /FIQ /IRQ ARM_BE A[22..0] /RD_WR /MREQ LOCK MAS0 MAS1 /MDP_RESET MDPCLK Flash PCX8 D[31..0] A[20..2] /RD /WR /FLASHCS /MDP_RESET SRAM PCX6 D[31..0] A[18..2] /RD /WR /SRAMCS0 /SRAMCS1 /SRAMCS2 /SRAMCS3 MDP SRAM PCX_11 SDATA[7..0] SADDR[14..0] /SCS /SRW /SOE ETHERNET PCX_10 D[15..0] ENETRST /ENETCS /WR /RD ETH_INT IOCHRDY A[6..2] LINK_LED Upstream RF PCX4 UPST_IF_OUT- PGA_DATA PGA_CLK /PGA_DATAEN UPST_IF_OUT+ /PGA_PD PD_OUT TUNER_UPST_IF Test Headers PCX_12 /RD /WR /SRAMCS0 ARM_BE MDPCLK MAS0 MAS1 /RD_WR /FLASHCS /WAIT /ENETCS /PHYCS /MREQ /UARTCS UART_RST /DFLASHCS A[22..0] D[31..0] /UART_INT USB PCX_13 /WR A[6..2] /USB_CS D[7..0] /RD UART_RST /USB_INT MAC Gate Array & Test Connector PCX9 D[31..0] SDATA[7..0] A[22..0] /RD_WR /MREQ LOCK MAS0 MAS1 /MDP_RESET MDPCLK /TXFULL TXERR MDCLK FSYNC INCORR DVALID MDOUT[7..0] SEC_MODE PD_OUT /USB_INT ETH_INT IOCHRDY /PGA_PD LED0 LED3 SADDR[14..0] /SCS /SRW /SOE PROFILE[2..0] TXCLK TXSTRT /TXEN TXDATA[7..0] /WAIT ARM_BE /IRQ /FIQ /RD /WR /SRAMCS0 /SRAMCS1 /SRAMCS2 /SRAMCS3 /FLASHCS /ENETCS /PHYCS TUNER_SCL TUNER_SDA /DFLASHCS /UARTCS UART_RST ENETRST /PHYRST /UART_INT LED2 /USB_CS PGA_DATA /PGA_DATAEN PGA_CLKLBT_TXEN RF_AGCRF_AGC IF_OUT+ IF_AGCIF_AGC IF_OUT-TUNER_UPST_IF PGA_DATAPGA_DATA TUNER_UPST_IF PGA_CLKPGA_CLKPD_OUT /PGA_DATAEN/PGA_DATAEN TUNER_SCL /PGA_PD TUNER_SDA UPST_IF_OUT+UPST_IF_OUT+ /RDUPST_IF_OUT-UPST_IF_OUT- /WR /TXFULL /PHYCS TXERR /PHYRST MDCLK LED0FSYNC TXCLKLED2 INCORRLED3 TXSTRT DVALID /TXEN /SCS SEC_MODE/SRW PD_OUT /SOE ETH_INT IOCHRDY /WAIT /WAIT /FIQ/RD_WRARM_BE /IRQ /IRQ/MREQ/FIQ /RD ARM_BELOCK/WR /SRAMCS0 MAS0/SRAMCS1 /SRAMCS2 MAS1/SRAMCS3 /FLASHCS /MDP_RESET/DFLASHCS /ENETCS MDPCLK/PHYCS /UARTCS UART_RST/RD ENETRST /PHYRST/WR TUNER_SCL/SRAMCS0 TUNER_SDA ARM_BE MDPCLK MAS0 MAS1 /RD_WR /RD /FLASHCS /WR /WAIT /SRAMCS0 /RD /ENETCS /SRAMCS1 LED0 /WR /PHYCS /SRAMCS2 LINK_LED /FLASHCS /MREQ /SRAMCS3 LED2 /MDP_RESET /UARTCS LED3 UART_RST ETH_INT /DFLASHCS IOCHRDY /RD /WR /ENETCS ENETRST A[9..2] D[7..0] PROFILE[2..0] SADDR[14..0] MDOUT[7..0]SDATA[7..0] TXDATA[7..0] A[22..0] D[31..0] A[22..0] D[31..0] A[18..2] D[31..0] A[20..2] D[31..0] A[6..2] D[15..0] PROFILE[2..0] /PGA_PD TXDATA[7..0] TXCLK TXSTRT /TXEN LINK_LED /UART_INT /UART_INT A[6..2] D[7..0] /RD /WR /USB_CS UART_RST /USB_INT /USB_CS SEC_MODE /USB_INT PGA_DATA PGA_CLK /PGA_DATAEN LBT_TXEN +3.3V +3.3V+3.3V+3.3V+3.3V+3.3V +3.3V R143 NC S1 R2 3K3 S1 LED1 LED ASSEMBLY L-934RQ/4G1AT 24 13 6810 579 C1C2 A1A2 C3C4C5 A3A4A5 R142 0 S1 R205 330 S1 R204 330 S1 R203 330 S1 R202 330 S1 R201 330 S1 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 DD CC BB AA FOR LBT4030 (U4) ONLY Vout=1.25(1+R130/R126) AIC-1563 LM3578A Vout=(R53/R54)+1 Route +2V away from analog section PCX2-3.SCHX2 PCX CABLE MODEM VER 6.1 TURBONET COMMUNICATIONS INC B 213Monday, February 14, 2000 Title SizeDocument NumberRev Date:Sheet of GND+3.3VDC +9VA+5VA +2V+32V VCC+3.3VLB +12V+12V +12V +12V +12V +12V +7.5V +7.5V +12V +3.3V +5VA +VCC +5V +3.3VDC +3.3VLB +32V +2V +9VA +7.5V D4 1N4148 S R72 1K S2 1% R87 390K S2 D7 1N4148 S R118 220 S2 R129 390K S2 R126 2K S2 1% R82 220 S2 R130 3K3 S2 1% + C50 470U/16V + C70 470U/16V + C47 10U/25V R61 3K9 S2 5% R100 100 S3 R60 270K S2 R138 270K S2 + C61 470U/16V R54 10K S2 MOV1 ZNR 68V/7mm L30 BEAD/600 S3 L13 TFU0940V NC L11 BEAD RADIAL L14 BEAD RADIAL JP9 POWER JACK R53 10K S2 + C73 10U/100V + C78 10U/100V R86 124K S2 1% L9 330uH DR0912 L10 470uH DR0912 L8 330uH TC5026 L5 330uH TC5026 C84 .1u/50V X7R S2 C98 .1u/50V X7R S2 C102 .1u/50V X7R S2 C131 .1u/50V X7R S2 C135 .1u/50V X7R S2 C136 .1u/50V X7R S2 + C57 470U/16V C139 .1u/50V X7R S2 C151 .1u/50V X7R S2 C69 1000P/50V X7R S2 C143 1000P/50V X7R S2 C87 .01u/50V X7R S2 C110 470P/50V X7R S2 C140 470P/50V X7R S2 C114 .033u/50V X7R S2 C142 .033u/50V X7R S2 C62 22P/50V NPO S2 C74 22P/50V NPO S2 C75 820P/50V NPO S2 C109 100P/50V NPO S2 D2 1N5819 RADIAL D1 1N5819 RADIAL D3 1N5819 RADIAL D8 1N5819 RADIAL C99 .1u/50V X7R S2 C133 .1u/50V X7R S2 L25 BEAD/26 S3 L27 68uH DR0608 C63 3300P/50V X7R S2 + C81B 470U/25V + C54 470U/16V R59 4K99 S2 1% L23 BEAD/26 S3 + C226 10U/25V + C81A 470U/25V R217 0.15 S5 R216 0.15 S5 R45 0.22 S5 R62 0.22 S5 + C225 10U/25V R231 1 S6 R23210 S6 NC R23310 S6 NC L37 BEAD/600 S3 C227 .1u/50V X7R S2 L38 BEAD/26 S3 + C229 10U/25V + C232 10U/25V L39 BEAD/600 S3 C230 .1u/50V X7R S2 C228 .1u/50V X7R S2 C231 .1u/50V X7R S2 R2340 S3 NC U14 AIC 1563 DIP 1 2 3 45 6 7 8 SC SE TC GNDFB VCC IS BST U10 AIC 1563 DIP 1 2 3 45 6 7 8 SC SE TC GNDFB VCC IS BST U17 LM3578A SOP8 1 2 3 45 6 7 8 IN- IN+ OSC GNDEMIT COLL CURR/L VIN U20 LM3578A SOP8 1 2 3 45 6 7 8 IN- IN+ OSC GNDEMIT COLL CURR/L VIN U7 LM78L09 TO-92 13 2 VIVO GND U31 LM7805 TO-220 13 2 VIVO GND U32 LM78L05 TO-92 13 2 VIVO GND JP6 HEADER 2*4 2.54mm (F) 1 3 5 7 2 4 6 8 + + + + + + + + 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 DD CC BB AA -15 TO +15dBm 88 to 860MHz TUNER RF In 5mA 12131415 RF In 13141516 P102GS1F R76 : 20K change to 13K R124 : 13K change to 20K R127 : 5K1 change to 3K R128 : 5K1 change to 6K8 R125 : 13K change to 20K Date : Jan-5- 00' R124 : 20K changet to 24K R69 : 1K changet to 0 ohm R76 : 13K changet to 20K R78 : 13K changet to 11K R75 : 5K1 changet to 4K7 Date : Feb-12-00' R124 : 24K S1 1% change to 20K S1 1% R207 : 0 S3 change to 2K7 S3 PTC2 : 5K S3T R128 : 6K8 S1 1% change to 4K3 S1 1% R127 : 3K S1 1% change to 3K6 S1 1% R69 : 0 S1 change to 47 S1 SCREW PCX3-2.SCHX2 PCX CABLE MODEM VER 6.1 TURBONET COMMUNICATIONS INC B 313Monday, Februar…

Text truncated - open the document above for the full version.

Product : DOCSIS Cable Modem Applicant : TURBOCOMM TECH. INC. FCC ID : N7ZDAZ8811F Model : DAZ8811F Series Report No. : MLT0003P15001 Test Date : March 24.2000 Test By Max Light Technology Co.,Ltd. Room 5, 8F, No.125, Section 3 Roosevelt Road, Taipei, Taiwan., R.O.C. Tel: 886-2-2363-2447 Fax: 886-2-2363-2597 T T h h e e t t e e s s t t r r e e p p o o r r t t c c o o n n s s i i s s t t s s o o f f 2 2 3 3 p p a a g g e e s s i i n n t t o o t t a a l l . . I I t t m m a a y y b b e e d d u u p p l l i i c c a a t t e e d d c c o o m m p p l l e e t t e e l l y y f f o o r r l l e e g g a a l l u u s s e e w w i i t t h h t t h h e e a a l l l l o o w w a a n n c c e e o o f f t t h h e e a a p p p p l l i i c c a a n n t t . . I I t t s s h h a a l l l l n n o o t t b b e e r r e e p p r r o o d d u u c c e e d d e e x x c c e e p p t t i i n n f f u u l l l l , , w w i i t t h h o o u u t t t t h h e e w w r r i i t t t t e e n n a a p p p p r r o o v v a a l l o o f f o o u u r r l l a a b b o o r r a a t t o o r r y y . . MAX LIGHT MEASUREMENT REPORT Page:2/23 Report Number: MLT0003P15001 FCC ID: N7ZDAZ8811F Technology Lab Table of Contents : I. General 4. II. Conducted Emissions Requirements 10. III. Radiated Emissions Requirements 14. Appendix I (EUT Test Setup) 19. Appendix II (Model List) 23. MAX LIGHT MEASUREMENT REPORT Page:3/23 Report Number: MLT0003P15001 FCC ID: N7ZDAZ8811F Technology Lab CERTIFICATION We here by verify that : The test data, data evaluation, test procedures and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4-1992. All test were conducted by MLT(Max Light Technology Co.,Ltd) Room 5, 8F, No.125, Section 3 Roosevelt Road, Taipei, Taiwan, R.O.C Also, we attest to the accuracy of each. We further submit that the energy emitted by the sample EUT tested as described in the report is in compliance with Class B radiated and conducted emission limit of FCC Rules Part 15 Subpart B. EUT: DOCSIS Cable Modem Applicant: TURBOCOMM TECH. INC. 4F-2, No.171, Sung-Tech Road, Taipei ,Taiwan Manufacturer: TURBOCOMM TECH. INC. No.369,Sec.3 Chun Cheng East Road, Wu Chuan Tsun,Ta Yuan Hsiang,Tao Yaun Hsien,Taiwan,R.O.C. Model No: DAZ8811F Series FCC ID: N7ZDAZ8811F Prepared by :Approved by : Country Huang Roger Chen MAX LIGHT MEASUREMENT REPORT Page:4/23 Report Number: MLT0003P15001 FCC ID: N7ZDAZ8811F Technology Lab I. GENERAL 1.1 Introduction The following measurement report is submitted on behalf of TURBOCOMM TECH. INC. In support of a Class B Digital Device certification in accordance with Part2 Subpart J and Part 15 Subpart A And B of the Commission’s and Regulations. 1.2 Description of EUT EUT: DOCSIS Cable Modem Applicant: TURBOCOMM TECH. INC. 4F-2, No.171, Sung-Tech Road, Taipei ,Taiwan Manufacturer: TURBOCOMM TECH. INC. No.369,Sec.3 Chun Cheng East Road, Wu Chuan Tsun,Ta Yuan Hsiang,Tao Yaun Hsien,Taiwan,R.O.C. Model No: DAZ8811F Series FCC ID : N7ZDAZ8811F Power Type: Powered by AC Adaptor (12V DC/1 Amp) Ethernet Cable: RJ-45 x1 (Nonshielded, 6’ long ,Plastic hoods) During testing the EUT was operated at Tx or Rx mode for each emission measured(P.S Run “Ping (IP Address) –T –L 1000” comment in Dos Mode). This was done in order to ensure that maximum emission levels were attained. MAX LIGHT MEASUREMENT REPORT Page:5/23 Report Number: MLT0003P15001 FCC ID: N7ZDAZ8811F Technology Lab 1.3 Description of Support Equipment In order to construct the minimum system which required by the ANSI C63.4-1991, following equipments were used as the support units. Computer: COMPAQ Model No.: 3284 Serial No.: L708BKTB4154 FCC ID: EJH3284 Keyboard: COMPAQ Model No.: KPQ-E99ZC-13 Serial No.: 237743-334 FCC ID: CMYKPQ7285 Monitor: COMPAQ Model No.: 303U Serial No.: 704AG19TG099 FCC ID: BJMCM14UH Mouse: COMPAQ Model No.: 196694-301 Serial No.: 1SH67CHE03360 FCC ID: EMJMUSJJ Printer: PANASONIC Model No.: KX-P1080I Serial No.: 7CKAKE98933 FCC ID: ACJ5Z6KX-P10801 Cable Head End: Cisco Model No.: Ubr7246 Serial No.: N/A MAX LIGHT MEASUREMENT REPORT Page:6/23 Report Number: MLT0003P15001 FCC ID: N7ZDAZ8811F Technology Lab Ethernet Card: DELTA Model No.: NE2000 Ethernet Adapter Serial No.: 4712544 Modem: Askey (External Fax / Data Modem) Model No.: WS1414VE Serial No.: IAH-10811 FCC ID: H8N1414VE MAX LIGHT MEASUREMENT REPORT Page:7/23 Report Number: MLT0003P15001 FCC ID: N7ZDAZ8811F Technology Lab Power Supply PC Monitor Printer Modem Keyboard Mouse EUT To Cable Head End RJ11C Cables RS-232 RS-232 UTP Cable Splitter RF Converter Cisco(uBR7246) System DHCP Server To Cable Modem Cable Modem Head End Coaxial Cable(5V-2C) 1.4 Configuration of System Under Test During testing the EUT(DOCSIS Cable Modem ) was connected to the Ethernet card’s RJ-45 port. So there is need for additional Ethernet Card(10BaseT). A mouse was connected to the mouse port and a printer was connected to the parallel port. A external modem connected the serial port and the external modem connected with two unterminated telephone cables on the line and phone jack. A coaxial cable(5C-2V) was connected to the F connector of EUT and the coaxial cable(5C-2V) was connected to a simulator of cable modem head end . MAX LIGHT MEASUREMENT REPORT Page:8/23 Report Number: MLT0003P15001 FCC ID: N7ZDAZ8811F Technology Lab Cable Modem Head End 1.5 Test Procedure All measurements contained in this report were performed according to the techniques described in Measurement procedure ANSI C63.4-1992 "Measurement of unIntentional Radiators." MAX LIGHT MEASUREMENT REPORT Page:9/23 Report Number: MLT0003P15001 FCC ID: N7ZDAZ8811F Technology Lab 1.6 General Test Condition The conditions under which the EUT operates were varied to determine their effect on the equipment's emission characteristics. The final configuration of the test system and the mode of operation used during these tests was chosen as that which produced the highest emission levels. However, only those conditions which the EUT …

Text truncated - open the document above for the full version.