NCMOMO0201-2GSM/GPRS/UMTS/HSDPA QUAD BAND PCI MINI CARD

GlobeTrotter GTM378E AGENCY REQUIREMENTS Licensed by QUALCOMM Incorporated under one or more of the following United States Patents and/or their counterparts in other nations: 4,901,307; 5,490,165; 5,056,109; 5,504,773; 5,101,501; 5,506,865; 5,109,390; 5,511,073; 5,228,054; 5,535,239; 5,267,261; 5,544,196; 5,267,262; 5,568,483; 5,337,338; 5,600,754; 5,414,796; 5,657,420; 5,416,797; 5,659,569; 5,710,784; 5,778,338 Federal communications commission notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: > Reorient or relocate the receiving antenna. > Increase the separation between the equipment and receiver. > Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. > Consult the dealer or an experienced radio or television technician for help. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Option could void the user's authority to operate the equipment. Cables The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. (Part 15.105 only applies for digital devices in the meaning of the FCC rules) Limited modular approval The integration is limited to fixed and mobile categorized end-products, so that 20 cm separation distance to end-user can be assured. You can integrate the module in a portable device as long as SAR testing will be performed on the end-product. Declaration of Conformity for products marked with the FCC logo - United States only This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions regarding your product or FCC declaration, contact: Option | Gaston Geenslaan 14| 3001 Leuven | Belgium www.option.com To identify this product, refer to the Part, Series, or Model number found on the product. This product has successfully completed the PTCRB requirements governing the release of new GSM 850/1900 capable products into the North American market. European Union declaration of conformity CE 0700 Products bearing the CE marking comply with the R&TTE Directive (99/5/EC), EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms (in parentheses are the equivalent international standards and regulations): Radio Frequency spectrum efficiency: > EN 301 511, v9.0.2 > EN 301 902-1&2, v2.2.1 > EN 300328:v1.6.1(2004-11) Electromagnetic Compatibility > EN 301 489-1: 2002 Safety and Health > EN 60950: 2001 > EN 50360 (07/2001) This product may be used in the following countries: > All EU Memberstates > Iceland > Switzerland > Norway > United States of America Manufacturer's Disclaimer Statement The information in this document is subject to change without notice and does not represent a commitment on the part of the vendor. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy, or fitness for any particular purpose of this document. The manufacturer reserves the right to make changes to the content of this document and/or the products associated with it at any time without obligation to notify any person or organization of such changes. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use this product or documentation, even if advised of the possibility of such damages. For questions regarding your product or declaration, contact: Option | Gaston Geenslaan 14| 3001 Leuven | Belgium www.option.com SYSTEM REQUIREMENTS > This is a module and should be integrated in devices mentioned in the “Integration manual”

layers RF exposure requirements -FCC 10 : NCMOM0020 1~2 Dear Examiner , M00201- 2 is marketed without defined ante nna. According to the limit i n 47 CFR 1.1310, we get the value of the maxim um antenna gain as follow: The maximum measured power output in the 850 MHz band is 154 8.82 mW (31.9dBm , see 71ayerstestreport MDE_O PT I_0611_FCCf). T he maximum permissible exposure is defined in 4 7 CFR 1.1310 with 0.549 m W/cm 2 • The transmitter is using indoor antennas that operate at 20 cm or more from nearby pers ons. The maximum antenna gain G is calcula ted using the genera l equation: S = P*G/4 nR 2 S = 0,549 mW/cm 2 P =1548.82 mW R=20 cm n =3.1416 Solving for G ; the maximum antenna gain is 2.512 dBL Best Regards 7 layers A G ~ LA. Yao Ji ng

7 layers AG Aufsichtsratsvorsitzenderh Registergerichth registered in: Borsigstrasse 11 Chairman of the Supervisory Board: Düsseldorf, HRB 44096 40880 Ratingen, Germany Markus Becker USt-IdNr h VAT Nr: Phone: +49 (0) 2102 749 0 Vorstandh Board: DE 203159652 Fax: +49 (0) 2102 749 350 Dr. Hans-Jürgen Meckelburg www.7Layers.com René Schildknecht InterLab  is a registered trademark of 7 layers AG FCC Measurement/Technical Report on GSM/UMTS Module MO0201 Report Reference: MDE_Opti_0611_FCCh Test Laboratory: 7 layers AG Borsigstrasse 11 40880 Ratingen Germany email: [email protected] DAT-P-192/99-01 Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the testing laboratory. Test report Reference: MDE_Opti_0611_FCCh Page 2 of 71 Table of Contents 0 Summary 3 0.1 Technical Report Summary 3 0.2 Measurement Summary 4 1 Administrative Data 6 1.1 Testing Laboratory 6 1.2 Project Data 6 1.3 Applicant Data 6 1.4 Manufacturer Data 6 2 Testobject Data 7 2.1 General EUT Description 7 2.2 EUT Main components 8 2.3 Ancillary Equipment 8 2.4 EUT Setups 8 2.5 Operating Modes 9 3 Test Results 10 3.1 RF Power Output 10 3.2 Frequency stability 14 3.3 Spurious emissions at antenna terminals 19 3.4 Field strength of spurious radiation 24 3.5 Emission and Occupied Bandwidth 28 3.6 Band edge compliance 32 4 Test Equipment 35 5 Photo Report 38 6 Setup Drawings 46 7 Annex 48 Measurement Plots Test report Reference: MDE_Opti_0611_FCCh Page 3 of 71 0 Summary 0.1 Technical Report Summary Type of Authorization Certification for a GSM cellular radiotelephone device Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 0 to 19 and Parts 20 to 69 (10-1-06 Edition). The following subparts are applicable to the results in this test report. Part 2 Subpart J - Equipment Authorization Procedures, Certification § 2.1046 Measurement required: RF power output § 2.1049 Measurement required: Occupied bandwidth § 2.1051 Measurement required: Spurious emissions at antenna terminals § 2.1053 Measurement required: Field strength of spurious radiation § 2.1055 Measurement required: Frequency stability § 2.1057 Frequency spectrum to be investigated Part 22 Subpart C – Operational and Technical Requirements § 22.355 Frequency tolerance Subpart H – Cellular Radiotelephone Service § 22.913 Effective radiated power limits § 22.917 Emission limitations for cellular equipment Summary Test The EUT complied with all performed tests as listed in chapter 0.2 Measurement Summary. Test report Reference: MDE_Opti_0611_FCCh Page 4 of 71 0.2 Measurement Summary RF Power Output The measurement was performed according to FCC §2.1046 10-1-06 OP-Mode Setup Port Final Result op-mode 1 setup_a01 antenna connector passed op-mode 2 setup_a01 antenna connector passed op-mode 3 setup_a01 antenna connector passed op-mode 4 setup_a01 antenna connector passed op-mode 5 setup_a01 antenna connector passed op-mode 6 setup_a01 antenna connector passed op-mode 7 setup_a01 antenna connector passed op-mode 8 setup_a01 antenna connector passed op-mode 9 setup_a01 antenna connector passed Frequency stability The measurement was performed according to FCC §2.1055 10-1-06 OP-Mode Setup Port Final Result op-mode 2 setup_01 antenna connector passed op-mode 5 setup_01 antenna connector passed op-mode 8 setup_01 antenna connector passed Spurious emissions at antenna terminals The measurement was performed according to FCC §2.1051 10-1-06 OP-Mode Setup Port Final Result op-mode 1 setup_a01 antenna connector passed op-mode 2 setup_01 antenna connector passed op-mode 3 setup_a01 antenna connector passed op-mode 4 setup_a01 antenna connector passed op-mode 5 setup_01 antenna connector passed op-mode 6 setup_a01 antenna connector passed op-mode 7 setup_01 antenna connector passed op-mode 8 setup_01 antenna connector passed op-mode 9 setup_01 antenna connector passed Field strength of spurious radiation The measurement was performed according to FCC §2.1053 10-1-06 OP-Mode Setup Port Final Result op-mode 1 setup_a02 enclosure passed op-mode 2 setup_02 enclosure passed op-mode 3 setup_a02 enclosure passed op-mode 4 setup_a02 enclosure passed op-mode 5 setup_02 enclosure passed op-mode 6 setup_a02 enclosure passed op-mode 7 setup_02 enclosure passed op-mode 8 setup_02 enclosure passed op-mode 9 setup_02 enclosure passed Emission and Occupied Bandwidth The measurement was performed according to FCC 52.1049 OP- Mode Setup Port op-mode 1 setup-01 antenna connector op-mode 2 setup-01 antenna connector op-mode 3 setup-01 antenna connector op-mode 4 setup-01 antenna connector op-mode 5 setup-01 antenna connector op-mode 6 setup-01 antenna connector op-mode 7 setup-01 antenna connector op-mode 8 setup-01 antenna connector op-mode 9 setup-01 antenna connector Band edge compliance fi The measurement was performed according to FCC 52.1053 OP-Mode Setup Port op-mode 1 setup-01 antenna connector op-mode 3 setup-01 antenna connector op-mode 4 setu p-0 1 antenna connector op-mode 6 setup-01 antenna connector op-mode 7 setup-01 antenna connector op-mode 9 setup-01 antenna connector 10-1-06 Final Result passed passed passed passed passed passed passed passed passed 10-1-06 Final Result passed passed passed passed passed passed After a hardware-change at the RF power amplifier previously performed tests have been repeated. This test report contains results for both hardware versions. For details please refer to the following chapters. This report replaces the test report referenced by: MDE-Opti-0611_FCCf, dated on 2007-03-09. 7 !ayers AG, Borsigstr. 11 QU LpLa(C bJ 40880 Ratingen, Germany Phone +49 (0)2102 749 0 desponsible for Responsible Accreditation Scope: for Test Report: Test report Reference: MDE-Opti-0611-FCCh Page 5 of 71 Test report Reference: MDE_Opti_0611_FCCh Page 6 of 71 1 Administrative Data 1.1 Testing Labora…

Text truncated - open the document above for the full version.

7 layers AG Aufsichtsratsvorsitzenderh Registergerichth registered in: Borsigstrasse 11 Chairman of the Supervisory Board: Düsseldorf, HRB 44096 40880 Ratingen, Germany Markus Becker USt-IdNr h VAT Nr: Phone: +49 (0) 2102 749 0 Vorstandh Board: DE 203159652 Fax: +49 (0) 2102 749 350 Dr. Hans-Jürgen Meckelburg www.7Layers.com René Schildknecht InterLab  is a registered trademark of 7 layers AG FCC Measurement/Technical Report on GSM/UMTS Module MO0201 Report Reference: MDE_Opti_0611_FCCi Test Laboratory: 7 layers AG Borsigstrasse 11 40880 Ratingen Germany email: [email protected] DAT-P-192/99-01 Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the testing laboratory. Test report Reference: MDE_Opti_0611_FCCi Page 2 of 72 Table of Contents 0 Summary 3 0.1 Technical Report Summary 3 0.2 Measurement Summary 4 1 Administrative Data 6 1.1 Testing Laboratory 6 1.2 Project Data 6 1.3 Applicant Data 6 1.4 Manufacturer Data 6 2 Testobject Data 7 2.1 General EUT Description 7 2.2 EUT Main components 8 2.3 Ancillary Equipment 8 2.4 EUT Setups 8 2.5 Operating Modes 9 3 Test Results 10 3.1 RF Power Output 10 3.2 Frequency stability 14 3.3 Spurious emissions at antenna terminals 19 3.4 Field strength of spurious radiation 24 3.5 Emission and Occupied Bandwidth 28 3.6 Band edge compliance 32 4 Test Equipment 35 5 Photo Report 38 6 Setup Drawings 47 7 Annex 49 Measurement Plots Test report Reference: MDE_Opti_0611_FCCi Page 3 of 72 0 Summary 0.1 Technical Report Summary Type of Authorization Certification for a GSM cellular radiotelephone device Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 0 to 19 and Parts 20 to 69 (10-1-06 Edition). The following subparts are applicable to the results in this test report. Part 2 Subpart J - Equipment Authorization Procedures, Certification § 2.1046 Measurement required: RF power output § 2.1049 Measurement required: Occupied bandwidth § 2.1051 Measurement required: Spurious emissions at antenna terminals § 2.1053 Measurement required: Field strength of spurious radiation § 2.1055 Measurement required: Frequency stability § 2.1057 Frequency spectrum to be investigated Part 24 Subpart E - Broadband PCS § 24.232 Power and antenna height limits § 24.235 Frequency stability § 24.236 Field strength limits § 24.238 Emission limitations for Broadband PCS equipment Summary Test Results: The EUT complied with all performed tests as listed in chapter 0.2 Measurement Summary. Test report Reference: MDE_Opti_0611_FCCi Page 4 of 72 0.2 Measurement Summary RF Power Output The measurement was performed according to FCC §2.1046 10-1-06 OP-Mode Setup Port Final Result op-mode 1 setup_a01 antenna connector passed op-mode 2 setup_a01 antenna connector passed op-mode 3 setup_a01 antenna connector passed op-mode 4 setup_a01 antenna connector passed op-mode 5 setup_a01 antenna connector passed op-mode 6 setup_a01 antenna connector passed op-mode 7 setup_03 antenna connector passed op-mode 8 setup_03 antenna connector passed op-mode 9 setup_03 antenna connector passed Frequency stability The measurement was performed according to FCC §2.1055 10-1-06 OP-Mode Setup Port Final Result op-mode 2 setup_01 antenna connector passed op-mode 5 setup_01 antenna connector passed op-mode 8 setup_03 antenna connector passed Spurious emissions at antenna terminals The measurement was performed according to FCC §2.1051 10-1-06 OP-Mode Setup Port Final Result op-mode 1 setup_a01 antenna connector passed op-mode 2 setup_01 antenna connector passed op-mode 3 setup_a01 antenna connector passed op-mode 4 setup_a01 antenna connector passed op-mode 5 setup_01 antenna connector passed op-mode 6 setup_a01 antenna connector passed op-mode 7 setup_03 antenna connector passed op-mode 8 setup_03 antenna connector passed op-mode 9 setup_03 antenna connector passed Field strength of spurious radiation The measurement was performed according to FCC §2.1053 10-1-06 OP-Mode Setup Port Final Result op-mode 1 setup_a02 enclosure passed op-mode 2 setup_02 enclosure passed op-mode 3 setup_a02 enclosure passed op-mode 4 setup_a02 enclosure passed op-mode 5 setup_02 enclosure passed op-mode 6 setup_a02 enclosure passed op-mode 7 setup_04 enclosure passed op-mode 8 setup_04 enclosure passed op-mode 9 setup_04 enclosure passed Emission and Occupied Bandwidth The measurement was performed according to FCC 52.1049 OP-Mode Setup Port op-mode 1 setup-01 antenna connector op-mode 2 setup-01 antenna connector op-mode 3 setup-01 antenna connector op-mode 4 setup-01 antenna connector op-mode 5 setup-01 antenna connector op-mode 6 setup-01 antenna connector op-mode 7 setup-03 antenna connector op-mode 8 setup-03 antenna connector op-mode 9 setup-03 antenna connector 10-1-06 Final Result passed passed passed passed passed passed passed passed passed n Band edge compliance The measurement was performed according to FCC 524.238 OP-Mode Setup Port op-mode 1 setup-01 antenna connector op-mode 3 setup-01 antenna connector op-mode 4 setu p-0 1 antenna connector op-mode 6 setup-01 antenna connector op-mode 7 setup-03 antenna connector op-mode 9 setup-03 antenna connector 10-1-06 Final Result passed passed passed passed passed passed After a hardware-change at the RF power amplifier previously performed tests have been repeated. This test report contains results for both hardware versions. For details please refer to the following chapters. This report replaces the test report referenced by: MDE-Opti-0611-FCCg, dated on 2007-03-09. h v ?? ,; > ., " f"' &- . )_I, I 7.9 L- 7 layers AG, Borsigstr. 11 40880 Ratingen, Gerniany Responsible for Responsible Accreditation Scope: for Test Report: Test report Reference: MDE-Opti-0611-FCCi Page 5 of 72 Test report Reference: MDE_Opti_0611_FCCi Page 6 of 72 1 Administrative Data 1.1 Testing Laboratory Company Name: 7 Laye…

Text truncated - open the document above for the full version.

Test report Reference: MDE_Opti_0611_FCCf/g Page 1 of 8 Photo Report Photo 1: EUT A (front side) Test report Reference: MDE_Opti_0611_FCCf/g Page 2 of 8 Photo 2: EUT B (front side) Test report Reference: MDE_Opti_0611_FCCf/g Page 3 of 8 Photo 3: EUT A (rear side) Test report Reference: MDE_Opti_0611_FCCf/g Page 4 of 8 Photo 4: EUT B (rear side) Test report Reference: MDE_Opti_0611_FCCf/g Page 5 of 8 Photo 5: Setup for radiated tests (EUT A operated in a cradle and with external antenna) Test report Reference: MDE_Opti_0611_FCCf/g Page 6 of 8 Photo 6: Setup for radiated tests (EUT B operated in a cradle and with external antenna) Test report Reference: MDE_Opti_0611_FCCf/g Page 7 of 8 Photo 7: Cradle AE1 (front side) Test report Reference: MDE_Opti_0611_FCCf/g Page 8 of 8 Photo 8: Cradle AE1 (rear side)