NLMSEW3035WNWireless LCD Monitor

WIRELESS MONITORING SYSTEM User Manual SEW-3035WN , SEB-1018RW SPECIFY SERVICE INSTRUCTIONS AND WARRANTY TERMS FCC NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. WARNING Some adult assembly or installation required. This product contains small parts that may cause choking. Keep small parts away from children. This product is NOT intended to replace proper supervision of children. You MUST check your child’s activity regularly, as this product will not alert parents to silent activities of a child. Before using this product, read and follow all instructions contained in this booklet, and read and follow all instructions and warnings on the product. To prevent entanglement with adapter cords, NEVER PLACE THE CORD IN OR NEAR A CRIB OR PLAYPEN. DO NOT place the product or its AC adapter cords within reach of children. ALWAYS KEEP THE TRANSMITTER, RECEIVER AND AC ADAPTERS OUT OF REACH OF CHILDREN. NEVER use the transmitter or receiver near water, including near a bathtub, sink, laundry tub, wet basement, etc. This product is intended for indoor use only. This product is not intended for use as a medical monitor and its use should not replace adult supervision. Check reception regularly. Test monitor before use and after changing camera location. Always unplug AC adapters from wall outlets and power sources during periods of non- use. Thewirelesssignaltransferrangemaybeshortenedifthereexistsanobstaclesuch asaconcretewall  SamsungTechwinCo.,Ltd.Allrights  reserved. Trademark is the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin. Disclaimer Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice. Wireless Monitoring System User Manual Copyright ©2011 between. • • • • • • • • • • • This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference; and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the distance between the equipment and the receiver. - Connect the equipment to outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. “ This appliance and its antenna must not be collocated or operation in conjunction with any other antenna or transmitter. A minimum separation distance of 20 cm must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirements." To prevent overheating, keep the product and AC power adapters away from any direct sunlight and heat sources such as radiators, heat registers, cooking devices (e.g., stoves and ovens) and other appliances that produce heat (e.g., amplifiers, televisions and stereos). Ensure that the product is well ventilated during use. Avoid contact with pillows and furniture that may block ventilation. Use only the AC adapters provided with the product, as other adapters may damage the product. Plug the adapters only into standard household current (120 volts AC). Place the AC adapters avoiding pinch points otherwise you can damage the adapters. When an AC adapter is plugged into a power source, DO NOT touch the exposed end of the AC adapter’s cord. Do not use extension cords with the AC power adapters to avoid entanglement. This product should only be serviced by qualified and authorized Samsung service centers. Images and sounds are transmitted by the product over public airwaves and transmissions may be picked up by other units. Caution if you use the system to watch a young child, do not place the camera where the child can reach. When using the system with only battery power and the charge is low, then the picture and or sound may affected. If this occurs then please connect the AC power adapter and/or replace with new batteries. If you are using the optional rechargeable battery then plug in the AC power adapter to recharge. BATTERY WARNING When using the product in portable mode, check batteries regularly. DO NOT use the monitor in portable mode when batteries are low. DISPOSE OF OR RECYCLE BATTERIES PROPERLY IN ACCO…

Text truncated - open the document above for the full version.

Letter of Authorization Company: SAMSUNG TECHWIN CO., LTD Address: #28 Seongju-Dong, Changwon-si, Kyungsangnam-do, Korea Product Name: WIRELESS LCD MONITOR Model Number: SEW-3035WN We authorize MiCOM Labs, 440 Boulder Court, Suite 200, Pleasanton, CA 94566, USA, to act on our behalf on all matters concerning the above named equipment. This shall include the following: - Testing - Approval applications and procedures - Payment of approval fees We declare that MiCOM Labs, 440 Boulder Court, Suite 200, Pleasanton, CA 94566, USA, is allowed to forward all information related to the approval project to the applied notified body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Name: Kang Jei Soon Date: Mar 09, 2011 Title: Manager Signature of applicant

SAMSUNG TECHWIN CO., LTD #28 Seongju-Dong, Changwon-si, Kyungsangnam-do, Korea Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD21046 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission's Rules (47 C.F.R) and Section §552(b)(4) of the Freedom of Information Act, SAMSUNG TECHWIN CO., LTD requests confidentiality for the following products: FCC ID Number Product Title / Model NLMSEW3035WN Wireless LCD Monitor For the product stated above, we request that the following information be held confidential: 1) Schematic diagrams 2) Bill of materials (Part List) 3) Block Diagram No other items submitted as part of the equipment authorization filing process are deemed confidential. The above exhibits contain SAMSUNG TECHWIN CO., LTD trade secrets and proprietary information that could be of benefit to our competitors regarding the design of our products. This material is not customarily available to the general public and we request that it be withheld from public inspection. Sincerely, (Jeisoon kang / Manager) (SAMSUNG TECHWIN CO., LTD)

http://www.emc2000.co.kr FCC TEST REPORT Report No.: EMC-FCC-R0043 EMC compliance Ltd. Page: 1 of 1 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval. Appendix 2. External photo of EUT

http://www.emc2000.co.kr FCC TEST REPORT Report No.: EMC-FCC-R0043 EMC compliance Ltd. 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval. Label Location

http://www.emc2000.co.kr FCC TEST REPORT Report No.: EMC-FCC-R0043 EMC compliance Ltd. Page: 1 of 2 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval. Appendix 3. Internal photo of EUT http://www.emc2000.co.kr FCC TEST REPORT Report No.: EMC-FCC-R0043 EMC compliance Ltd. Page: 2 of 2 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

SEW-3020/3022/3034/3035 2.4Ghz digital wireless monitor Architecture: SEW-3020/3022/3034/3035 is a low cost and high performance digital Wireless monitor which integrates M-JPEG codec , FHSS base band , RF transceiver ,CMOS sensor color processing unit , ADPCM codec, The base- band implement a Bluetooth like frequency adaptive hopping technology to prevent being jammed by microwave oven and other 2.4GHz devices. It can co-existence with Bluetooth, WLAN and other 2.4GHz digital-modulated devices. SEW-3020/3022/3034/3035 2.4Ghz Digital Wireless monitor hardware architecture is show in Block diagram z Auto ACK & retransmit On the air max. data rate 2Mpbs z Software selectable channel form 2400MHz to 2525MHz (125 Selectable channels) z Intelligent frequency hopping (change RF channel automatically) z Support AV Out z Support SD z Support Sound level indicate nRF24L01 is a single chip radio transceiver for the world wide 2.4 -2.5 GHz ISM band. The transceiver consists of a fully integrated frequency synthesizer, a power amplifier, a crystal oscillator, a demodulator, modulator and Enhanced ShockBurst™ protocol engine. Output power, frequency channels, and protocol setup are easily programmable through a SPI interface. Current consumption is very low, only 9.0mA at an output power of -6dBm and 12.3mA in RX mode. Built-in Power Down and Standby modes makes power saving easily realizable. A simplified block diagram of the nRF24L01 is shown in figure 2 Figure 2 : nRF24L01 Block Diagram Packet Handling Methods nRF24L01 has the following Packet Handling Methods: ShockBurst™ (compatible with nRF2401, nRF24E1, nRF2402 and nRF24E2 with 1Mbps data rate, see page 24) Enhanced ShockBurst™ ShockBurst™ ShockBurst™ makes it possible to use the high data rate offered by nRF24L01 without the need of a costly, high-speed microcontroller (MCU) for data processing/clock recovery. By placing all high speed signal processing related to RF protocol on-chip, nRF24L01 offers the application microcontroller a simple SPI compatible interface, the data rate is decided by the interface-speed the micro controller itself sets up. By allowing the digital part of the application to run at low speed, while maximizing the data rate on the RF link, ShockBurst™ reduces the average current consumption in applications. In ShockBurst™ RX, IRQ notifies the MCU when a valid address and payload is received respectively. The MCU can then clock out the received payload from an nRF24L01 RX FIFO. In ShockBurst™ TX, nRF24L01 automatically generates preamble and CRC, see Table 12. IRQ notifies the MCU that the transmission is completed. All together, this means reduced memory demand in the MCU resulting in a low cost MCU, as well as reduced software development time. nRF24L01 has a three level deep RX FIFO (shared between 6 pipes) and a three level deep TX FIFO. The MCU can access the FIFOs at any time, in power down mode, in standby modes, and during RF packet transmission. This allows the slowest possible SPI interface compared to the average datarate, and may enable usage of an MCU without hardware SPI. Enhanced ShockBurst™ Enhanced ShockBurst™ is a packet handling method with functionality that makes bi-directional link protocol implementation easier and more efficient. In a typical bi-directional link, one will let the terminating part acknowledge received packets from the originating part in order to make it possible to detect data loss. Data loss can then be recovered by retransmission. The idea with Enhanced ShockBurst™ is to let nRF24L01 handle both acknowledgement of received packets and retransmissions of lost packets, without involvement from the microcontroller. Figure 3: nRF24L01 in a star network configuration An nRF24L01 configured as primary RX (PRX) will be able to receive data trough 6 different data pipes, see Figure 3. A data pipe will have a unique address but share the same frequency channel. This means that up to 6 different nRF24L01 configured as primary TX (PTX) can communicate with one nRF24L01 configured as PRX, and the nRF24L01 configured as PRX will be able to distinguish between them. Data pipe 0 has a unique 40 bit configurable address. Each of data pipe 1-5 has an 8 bit unique address and shares the 32 most significant address bits. All data pipes can perform full Enhanced ShockBurst™ functionality. nRF24L01 will use the data pipe address when acknowledging a received packet. This means that nRF24L01 will transmit ACK with the same address as it receives payload at. In the PTX device data pipe 0 is used to received the acknowledge, and therefore the receive address for data pipe 0 has to be equal to the transmit address to be able to receive the acknowledge. See Figure 5 for addressing example. Figure 4: Example on how the acknowledgement addressing is done An nRF24L01 configured as PTX with Enhanced ShockBurst™ enabled, will use the ShockBurst™ feature to send a packet whenever the microcontroller wants to. After the packet has been transmitted, nRF24L01 will switch on its receiver and expect an acknowledgement to arrive from the terminating part. If this acknowledgement fails to arrive, nRF24L01 will retransmit the same packet until it receives an acknowledgement or the number of retries exceeds the number of allowed retries given in the SETUP_RETR_ARC register. If the number of retries exceeds the number of allowed retries, this will show in the STATUS register bit MAX_RT and gives an interrupt. Whenever an acknowledgement is received by an nRF24L01 it will consider the last transmitted packet as delivered. It will then be cleared from the TX FIFO, and the TX_DS IRQ source will be set high. With Enhanced ShockBurst™ nRF24L01 offers the following benefits: Highly reduced current consumption due to short time on air and sharp timing when operating with acknowledgement traffic Lower system cost. Since the nRF24L01 handles all the high-speed link layer operations, like re-transmission of lost packet and gener…

Text truncated - open the document above for the full version.

http://www.emc2000.co.kr FCC TEST REPORT Report No.: EMC-FCC-R0043 EMC compliance Ltd. 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval. Appendix 9. Antenna Specification ˦̌̆̇˸̀ʳ˦˸̇̈̃˔́̇˸́́˴ʳˣ˴̇̇˸̅́ ˀˈ˃ˁ˃˃ ˀˇˈˁ˃˃ ˀˇ˃ˁ˃˃ ˀˆˈˁ˃˃ ˀˆ˃ˁ˃˃ ˀ˅ˈˁ˃˃ ˀ˅˃ˁ˃˃ ˀ˄ˈˁ˃˃ ˀ˄˃ˁ˃˃ ˀˈˁ˃˃ ˃ˁ˃˃ ˈˁ˃˃ ˄˃ˁ˃˃˄˃ˁ˃˃ ˌ˃ ˄ˋ˃ ˅ˊ˃ ˔́̇ˁʳ˕̅˴́˷ˍ ˔́̇ˁʳˠ̂˷˸˿ˍ ˧˸̆̇ʳˣ˸̅̆̂́ˍ ˢ̇˻˸̅ʳ ̃́˹̂ˁˍ˫ʳ˴̋˼̆ʳ ʳʳ ˥˸̀˴̅˾ ˩˸̅̇˼˶˴ ˥˸˶˸˼̉˸ʳ˔́̇ˁʳˣ̂˿˴̅˼̍˴̇̂́ ˀˆˇˁˆ˃ ˠ˼́ˁʳ ̊˴˼́ʻ˷˕˼ʼ ˀ˅ˁˆˌ ˠ˴̋ˁʳ̉˴˿̈˸ʻ˷˕˼ʼ ˀˊˁ˅ˊ ˔̉˸̅˴˺˸ʳ ̊˴˼́ʳʻ˷˕˼ʼ ˔́̇˸́́˴ʳˠ˸˴̆̈̅˸̀˸́̇ʳ˦̌̆̇˸̀ ˦̌̆̇˸̀ʳ˦˸̇̈̃˔́̇˸́́˴ʳˣ˴̇̇˸̅́ ˀˈ˃ˁ˃˃ ˀˇˈˁ˃˃ ˀˇ˃ˁ˃˃ ˀˆˈˁ˃˃ ˀˆ˃ˁ˃˃ ˀ˅ˈˁ˃˃ ˀ˅˃ˁ˃˃ ˀ˄ˈˁ˃˃ ˀ˄˃ˁ˃˃ ˀˈˁ˃˃ ˃ˁ˃˃ ˈˁ˃˃ ˄˃ˁ˃˃˄˃ˁ˃˃ ˌ˃ ˄ˋ˃ ˅ˊ˃ ˔́̇ˁʳ˕̅˴́˷ˍ ˔́̇ˁʳˠ̂˷˸˿ˍ ˧˸̆̇ʳˣ˸̅̆̂́ˍ ˢ̇˻˸̅ʳ ̃́˹̂ˁˍ ˬˀʳ˔˫ ̃˦ ˥˸̀˴̅˾ ˩˸̅̇˼˶˴ ˥˸˶˸˼̉˸ʳ˔́̇ˁʳˣ̂˿˴̅˼̍˴̇̂́ ˀˇ˄ˁˋˊ ˠ˼́ˁʳ ̊˴˼́ʻ˷˕˼ʼ ˀˋˁˋˋ ˠ˴̋ˁʳ̉˴˿̈˸ʻ˷˕˼ʼ ˀ˄ˉˁˋ˄ ˔̉˸̅˴˺˸ʳ ̊˴˼́ʳʻ˷˕˼ʼ ˔́̇˸́́˴ʳˠ˸˴̆̈̅˸̀˸́̇ʳ˦̌̆̇˸̀ ˦̌̆̇˸̀ʳ˦˸̇̈̃˔́̇˸́́˴ʳˣ˴̇̇˸̅́ ˀˈ˃ˁ˃˃ ˀˇˈˁ˃˃ ˀˇ˃ˁ˃˃ ˀˆˈˁ˃˃ ˀˆ˃ˁ˃˃ ˀ˅ˈˁ˃˃ ˀ˅˃ˁ˃˃ ˀ˄ˈˁ˃˃ ˀ˄˃ˁ˃˃ ˀˈˁ˃˃ ˃ˁ˃˃ ˈˁ˃˃ ˄˃ˁ˃˃˄˃ˁ˃˃ ˌ˃ ˄ˋ˃ ˅ˊ˃ ˔́̇ˁʳ˕̅˴́˷ˍ ˔́̇ˁʳˠ̂˷˸˿ˍ ˧˸̆̇ʳˣ˸̅̆̂́ˍ ˢ̇˻˸̅ʳ ̃́˹̂ˁˍ ʳ˭ʳˀ˔˫ ̃˦ ˥˸̀˴̅˾ ˩˸̅̇˼˶˴ ˥˸˶˸˼̉˸ʳ˔́̇ˁʳˣ̂˿˴̅˼̍˴̇̂́ ˀˇ˅ˁˇ˄ ˠ˼́ˁʳ ̊˴˼́ʻ˷˕˼ʼ ˀˊˁˌ˅ ˠ˴̋ˁʳ̉˴˿̈˸ʻ˷˕˼ʼ ˀ˄ˈˁˋˉ ˔̉˸̅˴˺˸ʳ ̊˴˼́ʳʻ˷˕˼ʼ ˔́̇˸́́˴ʳˠ˸˴̆̈̅˸̀˸́̇ʳ˦̌̆̇˸̀

http://www.emc2000.co.kr
FCC
TEST
REPORT
Report
No.:
EMCFCCR0043


EMC compliance Ltd.



































































Page:
38
of
39 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax)

This
test
report
shall
not
be
reproduced
except
in
full,
Without
the
written
approval.

5.10
RF
Exposure

5.10.1
Regulation

According
to
§15.247(i),
systems
operating
under
the
provisions
of
this
section
shall
be
operated
in
a
manner
that
ensures
that
the
public
is
not
exposed
to
radio
frequency
energy
levels
in
excess
of
the
Commission's
guidelines.
See
§
1.1307(b)(1)
of
this
Chapter.

Limits
for
Maximum
Permissive
Exposure:
RF
exposure
is
calculated.
Frequency
Range
Electric
Field
Strength
[V/m]
Magnetic
Field
Strength
[A/m]
Power
Density
[mW/cm 2 ]
Averaging
Time
[minute]
Limits
for
General
Population
/
Uncontrolled
Exposure
0.3
~
1.34
614
1.63
*(100)
30
1.34
~
30
824
/f
2.19/f
*(180/f 2 )
30
30
~
300
27.5
0.073
0.2
30
300
~
1500
/
/
f/1500
30
1500
~
15000
/
/
1.0
30
f=frequency in MHz, *= plane-wave equivalent power density
MPE (Maximum Permissive Exposure) Prediction Predication
of
MPE
limit
at
a
given
distance:
Equation
from
page
18
of
OET
Bulletin
65,
Edition
9701
() SPGRRPGSππ4




4 2 =⇒=
S=power
density
[mW/cm 2 ]
P=Power
input
to
antenna
[mW]
G=Power
gain
of
the
antenna
in
the
direction
of
interest
relative
to
an
isotropic
radiator
R=
distance
to
the
center
of
radiation
of
the
antenna
[cm]

EUT:
Maximum
peak
output
power
=
3.119mW](=
4.94
dBm)
Antenna
gain=0.943(=2.39[dBi])
100
mW,
at
20
cm
from
an
antenna
6[dBi]
S
=
PG/4πR²
=
100
×
3.98
/
(4
×
π
×
400)
=
0.0792
[mW/cm 2 ]
<
1.0
[mW/cm 2 ]
3.119
mW,
at
20
cm
from
an
antenna
2.39[dBi]
S
=
PG/4πR²=
0.0006
[mW/cm 2 ]
<
1.0
[mW/cm 2 ]
3.119
mW,
at
2.5
cm
from
an
antenna
2.39[dBi]
S
=
PG/4πR²=
0.0376
[mW/cm 2 ]
<
1.0
[mW/cm 2 ]

5.10.2
RF
Exposure
Compliance
Issue

The
information
should
be
included
in
the
user’s
manual:
This
appliance
and
its
antenna
must
not
be
colocated
or
operation
in
conjunction
with
any
other
antenna
or
transmitter.
A
minimum
separation
distance
of
20
cm
must
be
maintained
between
the
antenna
and
the
person
for
this
appliance
to
satisfy
the
RF
exposure
requirements.

http://www.emc2000.co.kr
FCC
TEST
REPORT
Report
No.:
EMCFCCR0043


EMC compliance Ltd.



































































Page:
1
of
39 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax)

This
test
report
shall
not
be
reproduced
except
in
full,
Without
the
written
approval.


FCC TEST REPORT
Test report No.: EMC- FCC- R0043 FCC ID: NLMSEW3035WN Type of equipment: WIRELESS LCD MONITOR Model Name: SEW-3035WN Brand Name: - Applicant: Samsung Techwin Co., Ltd. FCC Rule Part(s): FCC Part 15 Subpart C Section 15.203, Section 15.209 Section 15.207, Section 15.247 Frequency Range: 2402 MHz ~ 2478 MHz Test result: Complied





The
above
equipment
was
tested
by
EMC
compliance
Testing
Laboratory
for
compliance
with
the
requirements
of
FCC
Rules
and
Regulations.


The
results
of
testing
in
this
report
apply
to
the
product/system
which
was
tested
only.
Other
similar
equipment
will
not
necessarily
produce
the
same
results
due
to
production
tolerance
and
measurement
uncertainties.


Date of test: February 24, 2011 ~ March 8, 2011 Issued date: March 9, 2011 Tested by: Approved by: . KIM,
CHANG
MIN








































YOO,
SUNG
YOUNG







http://www.emc2000.co.kr
FCC
TEST
REPORT
Report
No.:
EMCFCCR0043


EMC compliance Ltd.



































































Page:
2
of
39 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax)

This
test
report
shall
not
be
reproduced
except
in
full,
Without
the
written
approval.
[ Contents ] 1. Client information .......................................................................................... 3 2. Laboratory information .................................................................................. 4 3. Description of E.U.T. ....................................................................................... 5 3.1
Basic
description
..........................................................................................
5 3.2
General
description
.......................................................................................
5 3.3
Test
frequency
.............................................................................................
6 3.4
Test
Voltage
.................................................................................................
6 4. Summary of test results ................................................................................. 7 4.1
Standards
&
results
......................................................................................
7 4.2
Uncertainty
.................................................................................................
7 5. Test results .................................................................................................... 8 5.1
Antenna
Requirement
...................................................................................
8 5.2
Maximum
Peak
Output
Power
........................................................................
9 5.3
Carrier
Frequency
Separation........................................................................
12 5.4
20
dB
Channel
Bandwidth
............................................................................
14 5.5
Number
of
Hopping
Channels
........................................................................
17 5.6
Time
of
Occupancy(Dwell
Time)
....................................................................
19 5.7
SPURIOUS
EMISSION,
BAND
EDGE,
AND
RESTRICTED
BANDS
..........................
22 5.8
Peak
Power
Spectral
Density
.........................................................................
31 5.9
Conducted
Emission
....................................................................................
34 5.10
RF
Exposure
.............................................................................................
38 6. Test equipment used for test ....................................................................... 39 Appendix 1 Test setup photos Appendix 2 External photos of EUT Appendix 3 Internal photos of EUT Appendix 4 Block diagram Appendix 5 Schematics Appendix 6 User manual Appendix 7 Part list Appendix 8 Layout diagram Appendix 9 Antenna Specification

http://www.emc2000.co.kr
FCC
TEST
REPORT
Report
No.:
EMCFCCR0043


EMC compliance Ltd.



































































Page:
3
of
39 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax)

This
test
report
shall
not
be
reproduced
except
in
full,
Without
the
written
approval.
1.
Client
information

Applicant:


Samsung
Techwin
Co.,
Ltd.
Address:



#42
SeongjuDong,
ChangwonShi,

KyungsangnamDo,
Korea
Telephone number: +82312773695 Facsimile number : +82312773695 Contact person:


Jeisoon
Kang/
[email protected] Manufacturer: RDI
TECHNOLOGY
Co.,Ltd
Address : Building
C1,Xintang
Industrial
Park,East




































Baishixia,Fuyong,Baoan,Shenzhen,PRC.



http://www.emc2000.co.kr
FCC
TEST
REPORT
Report
No.:
EMCFCCR0043


EMC compliance Ltd.



































































Page:
4
of
39 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax)

This
test
report
shall
not
be
reproduced
except
in
full,
Without
the
written
approval.
2.
Laboratory
information

Address




EMC
Compliance
Ltd.
480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea

Telephone
Number:
82
31
336
9919



Facsimile
Number:
82
31
336
4767

Certificate
CBTL
Testing
Laboratory,
KOLAS
NO.:
231
FCC
Filing
No.:
793334
VCCI
Registration
No.:
C1713,
R1606,
T258

SITE
MAP
SUWONCITY
EMC Compliance Ltd.
http://www.emc2000.co.kr
FCC
TEST
REPORT
Report
No.:
EMC…

Text truncated - open the document above for the full version.

http://www.emc2000.co.kr FCC TEST REPORT Report No.: EMC-FCC-R0043 EMC compliance Ltd. Page: 1 of 2 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval. Appendix 1. Test Setup photos - Below 1GHz - Abobe 1GHz http://www.emc2000.co.kr FCC TEST REPORT Report No.: EMC-FCC-R0043 EMC compliance Ltd. Page: 2 of 2 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval. - Conducted Emission front - Conducted Emission rear