O3M9290002265XLED LAMPS

Please go to www.meethue.com to learn more about hue and how to use it. FCC ID bridge: EW780891300 FCC ID lamp: O3M9290002265X This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • Risk of electric shock – Do not use device where directly exposed to water. • Before replacing, turn off power and let the bulb cool to avoid electrical shock or burn. • The device is for indoor use only. • Do not use the device in wet locations, e.g. bathrooms or outdoors. OPERATING INSTRUCTIONS: • This device is not a toy designed to be played with by children. • Do not place the device on hot surfaces. • For safety reasons, do not open device, which will also void the warranty. • Only use the adaptor supplied; using a different adaptor can damage the device. IC Certication: - LED lamp: company number: 10469A, UPN: 2265X. - ZigBee IP bridge: company number: 1135B, UPN: 80891300. This Class B digital apparatus complies with Canadian ICES-003. This digital apparatus does not exceed the class B limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications. NOTICE: Changes or modications made to this device not expressly approved by Philips Lighting Company (USA) and Philips Electronics Ltd (Canada) (collectively “Philips”) may void the U.S. FCC and Canadian authorization to operate this device. The advanced interface module complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modica- tions to this equipment. Such modications could void the user's authority to operate the equipment. This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna – Increase the separation between the device and receiver – Connect the device into an outlet on a circuit different from that to which the receiver is connected – Consult the dealer or an experienced radio/television technician for help WARNINGS AND CAUTIONS: • The bulb is suitable for use in open luminaries (xtures). • The bulb is not suitable for totally enclosed fixtures. • The bulb is not intended for use with emergency exit xtures or emergency lights. • The bulb is not compatible with photo controls, occupancy sensors, or timing devices unless specically designed for hue. • The bulb is not suitable for use with dimmers. • The bulb is not suitable for use with dimmers. misuse or acts of God. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURA- TION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUEN- TIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specic legal rights, and you may also have other rights which vary from state to state and province to province. CLEANING AND MAINTENANCE: Do not clean the device when it is on and connected to the power supply. To avoid scratching the device, clean only with a soft dry cloth. Do not use cleaning agents to clean the device. Manage in accordance with disposal laws in your area. “Hue Personal Wireless Lighting” is a trademark owned by Koninklijke Philips Electronics N.V. Wireless Specication: Wireless RF mode frequency band: 2400~2483.5 MHz Wireless communications protocol: IEEE 802.15.4 Operating channels: channels 11 – 26 Environmental specication: Temperature (operation): 0-35 °C Temperature (Storage): -25-60 °C Relative humidity: 5-95 % non condensing Standby power: 0.45 W per lamp Use Conditions: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: – This device may not cause harmful interference – This device must accept any interference received, including interference that may cause undesired operation FCC Warning: Changes or modications not expressly approved by the party responsible • Use the bulb only in a socket rated for this bulb. LIMITED WARRANTY: Philips warrants that this device will be free from defects in material and workmanship and will operate for 2 years based on up to 3 hours average usage per day/7 days per week, when used as directed. If this device does not conform to the warranty, Philips will send you, at its election, a replacement device or refund your original purchase price upon receipt of the returned device, register receipt and proof of purchase. Please call our toll-free number 1-800-555-0050, write to Philips (address indicated on the packaging) or send an email at the website www.philips.com to nd out how to return the device. This limited warranty does not cover devices subject to accident, neglect, abuse, EN FR for compliance c…

Text truncated - open the document above for the full version.

FIGURE 1 LED LAMPS (M/N: 9290002265) GENERAL APPEARANCE

FIGURE 1 LED LAMPS (M/N: 9290002265) COVER REMOVED FIGURE 2 LED LAMPS (M/N: 9290002265) LED DRIVER (FRONT VIEW) F IGURE 3 LED LAMPS (M/N: 9290002265) LED DRIVER (BACK VIEW) FIGURE 4 LED LAMPS (M/N: 9290002265) LED BOARD (FRONT VIEW) F IGURE 5 LED LAMPS (M/N: 9290002265) LED BOARD (BACK VIEW) FIGURE 6 LED LAMPS (M/N: 9290002265) RF BOARD (FRONT VIEW) F IGURE 7 LED LAMPS (M/N: 9290002265) RF BOARD (BACK VIEW)

PHILIPS LIGHTING CO, DIV OF PHILIPS ELECTRONICS NORTH AMERICA CORP FCC ID: O3M9290002265X Page 1 of 7 Audix Technology (Shanghai) Co., Ltd. Report No.: ACI-F12125 Prepared For : PHILIPS LIGHTING CO, DIV OF PHILIPS ELECTRONICS NORTH AMERICA CORP 200 Franklin Square Drive Somerset, NJ 08873, USA Prepared By : Audix Technology (Shanghai) Co., Ltd. 3F 34Bldg 680 Guiping Rd., Caohejing Hi-Tech Park, Shanghai 200233, China Tel: +86-21-64955500 Fax: +86-21-64955491 Report No. : ACI-F12125 Date of Test : Jul. 05, 2012 Date of Report : Jul. 19, 2012 Application for FCC Certification On behalf of PHILIPS LIGHTING CO, DIV OF PHILIPS ELECTRONICS NORTH AMERICA CORP Product Name: LED LAMPS Model No.: 9290002265 Serial No.: E1206790-06/06 FCC ID: O3M9290002265X (MPE Calculation) PHILIPS LIGHTING CO, DIV OF PHILIPS ELECTRONICS NORTH AMERICA CORP FCC ID: O3M9290002265X Page 2 of 7 Audix Technology (Shanghai) Co., Ltd. Report No.: ACI-F12125 TABLE OF CONTENTS Page 1 GENERAL INFORMATION .......................................................................................................... 4 1.1 Description of Equipment Under Test ........................................................................................ 4 1.2 Description of Test Facility ........................................................................................................ 5 1.3 Measurement Uncertainty .......................................................................................................... 5 2 SUMMARY OF STANDARDS AND RESULTS .......................................................................... 6 2.1 Applicable Standard ................................................................................................................... 6 2.2 Specification Limits ................................................................................................................... 6 2.3 MPE Calculation Method ........................................................................................................... 6 2.4 Calculated Result ........................................................................................................................ 7 PHILIPS LIGHTING CO, DIV OF PHILIPS ELECTRONICS NORTH AMERICA CORP FCC ID: O3M9290002265X Page 3 of 7 Audix Technology (Shanghai) Co., Ltd. Report No.: ACI-F12125 TEST REPORT FOR FCC CERTIFICATE Applicant : PHILIPS LIGHTING CO, DIV OF PHILIPS ELECTRONICS NORTH AMERICA CORP Manufacturer : Philips (China) Investment Co., Ltd. Factory #1 : CHANGAN WIN CHANNEL ELECTRONICS COMPANY LIMITED Factory #2 : Arts Electronics Co., Ltd. EUT Description : LED LAMPS (A) Model No. : 9290002265 (B) Serial No. : E1206790-06/06 (C) Test Voltage : AC 120V/60Hz Test Procedure Used: FCC OET Bulletin 65 August 1997 The device described above is tested by Audix Technology (Shanghai) Co., Ltd. to determine the maximum emission levels emanating from the device. The maximum emission levels are compared to the FCC OET Bulletin 65. The test results are contained in this test report and Audix Technology (Shanghai) Co., Ltd. is assumed full responsibility for the accuracy and completeness of these measurements. This report also shows that the EUT (M/N: 9290002266, S/N: E1206790-06/06), which was tested on Jan. 13, 2012 is technically compliance with the FCC limits. This report applies to above tested sample only. This report shall not be reproduced in part without written approval of Audix Technology (Shanghai) Co., Ltd. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. Date of Test : Jul. 05, 2012 Date of Report : Jul. 19, 2012 Producer : KATHY WANG / Assistant Review : DIO YANG / Assistant Manager Signatory : SAMMY CHEN / Deputy Manager PHILIPS LIGHTING CO, DIV OF PHILIPS ELECTRONICS NORTH AMERICA CORP FCC ID: O3M9290002265X Page 4 of 7 Audix Technology (Shanghai) Co., Ltd. Report No.: ACI-F12125 1 GENERAL INFORMATION 1.1 Description of Equipment Under Test Description : LED LAMPS Type of EUT ; Production … Pre-product … Pro-type Model Number : 9290002265 Serial Number : E1206790-06/06 Radio Tech : IEEE 802.15.4 (ZigBee®) Freq. Band : 2405 MHz - 2480 MHz Total 5 Channels: (2405 MHz, 2425 MHz, 2450 MHz, 2475 MHz, 2480 MHz) Tested Freq. : 2405 MHz (Channel 01) 2450 MHz (Channel 03) 2480 MHz (Channel 05) Antenna Gain : -10.0 dBi Applicant : PHILIPS LIGHTING CO, DIV OF PHILIPS ELECTRONICS NORTH AMERICA CORP 200 Franklin Square Drive Somerset, NJ 08873, USA Manufacturer : Philips (China) Investment Co., Ltd. No.9, Lane 888, Tian Lin Road, 200233, Shanghai, China Factory #1 : CHANGAN WIN CHANNEL ELECTRONICS COMPANY LIMITED No.85, TONG GU XIA LU, SHANGJIAO COMMUNITY, CHANGAN TOWN, DONGGUAN CITY, GUANGDONG PROVINCE, CHINA Factory #2 : Arts Electronics Co., Ltd. No.1 Shang Xing Lu, Shang Jiao Community, Chang An Town, Dongguan City, Guangdong Province 523000, China. PHILIPS LIGHTING CO, DIV OF PHILIPS ELECTRONICS NORTH AMERICA CORP FCC ID: O3M9290002265X Page 5 of 7 Audix Technology (Shanghai) Co., Ltd. Report No.: ACI-F12125 1.2 Description of Test Facility Site Description : Sept. 17, 1998 file on (Semi-Anechoic Chamber) Apr 29, 2009 Renewed Federal Communications Commission FCC Engineering Laboratory 7435 Oakland Mills Road Columbia, MD 21046, USA Name of Firm : Audix Technology (Shanghai) Co., Ltd. Site Location : 3 F 34 Bldg 680 Guiping Rd., Caohejing Hi-Tech Park, Shanghai 200233, China FCC registration Number : 91789 Accredited by NVLAP, Lab Code : 200371-0 1.3 Measurement Uncertainty Output Power Expanded Uncertainty : U = 0.30 dB PHILIPS LIGHTING CO, DIV OF PHILIPS ELECTRONICS NORTH AMERICA CORP FCC ID: O3M9290002265X Page 6 of 7 Audix Technology (Shanghai) Co., Ltd. Report No.: ACI-F12125 2 SUMMARY OF STANDARDS AND RESULTS 2.1 Applicable Standard FCC OET Bulletin 65:1997 2.2 Specification Limits Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electr…

Text truncated - open the document above for the full version.

Philips (China) Investment Co., Ltd. FCC ID: O3M9290002265X Page 1 of 43 Audix Technology (Shanghai) Co., Ltd. Report No.: ACI-F12124 Prepared For : Philips (China) Investment Co., Ltd. No.9, Lane 888, Tian Lin Road, 200233, Shanghai, China Prepared By :Audix Technology (Shanghai) Co., Ltd. 3F 34Bldg 680 Guiping Rd., Caohejing Hi-Tech Park, Shanghai 200233, China Tel: +86-21-64955500 Fax: +86-21-64955491 Report No. : ACI-F12124 Date of Test : Jul. 05 - 16, 2012 Date of Report : Jul. 19, 2012 Application for FCC Certification On behalf of Philips (China) Investment Co., Ltd. Product Name: LED LAMPS Model No.: 9290002265 Serial No.: E1206790-06/06 FCC ID: O3M9290002265X Philips (China) Investment Co., Ltd. FCC ID: O3M9290002265X Page 2 of 43 Audix Technology (Shanghai) Co., Ltd. Report No.: ACI-F12124 TABLE OF CONTENTS Page 1 SUMMARY OF STANDARDS AND RESULTS .......................................................................... 5 1.1 Description of Standards and Results ......................................................................................... 5 2 GENERAL INFORMATION .......................................................................................................... 6 2.1 Description of Equipment Under Test ........................................................................................ 6 2.2 Description of Test Facility ........................................................................................................ 7 2.3 Measurement Uncertainty .......................................................................................................... 7 3 CONDUCTED EMISSION TEST .................................................................................................. 8 3.1 Test Equipment ........................................................................................................................... 8 3.2 Block Diagram of Test Setup ..................................................................................................... 8 3.3 Conducted Emission Limit [FCC Part 15 Subpart B 15.207] .................................................... 8 3.4 Test Configuration ...................................................................................................................... 9 3.5 Operating Condition of EUT ...................................................................................................... 9 3.6 Test Procedures .......................................................................................................................... 9 3.7 Test Results ................................................................................................................................ 9 4 RADIATED EMISSION TEST ..................................................................................................... 11 4.1 Test Equipment ......................................................................................................................... 11 4.2 Block Diagram of Test Setup ................................................................................................... 11 4.3 Radiated Emission Limit [FCC Part 15 Subpart C 15.209] ..................................................... 12 4.4 Test Configuration .................................................................................................................... 12 4.5 Operating Condition of EUT .................................................................................................... 12 4.6 Test Procedures ........................................................................................................................ 12 4.7 Test Results .............................................................................................................................. 14 5 6 dB BANDWIDTH MEASUREMENT ....................................................................................... 24 5.1 Test Equipment ......................................................................................................................... 24 5.2 Block Diagram of Test Setup ................................................................................................... 24 5.3 Specification Limits (§15.247(a)(2)) ........................................................................................ 24 5.4 Operating Condition of EUT .................................................................................................... 24 5.5 Test Procedure .......................................................................................................................... 24 5.6 Test Results .............................................................................................................................. 24 6 MAXIMUM PEAK OUTPUT POWER MEASUREMENT ...................................................... 27 6.1 Test Equipment ......................................................................................................................... 27 6.2 Block Diagram of Test Setup ................................................................................................... 27 6.3 Specification Limits ((§15.247(b)(3)) ...................................................................................... 27 6.4 Operating Condition of EUT .................................................................................................... 27 6.5 Test Procedure .......................................................................................................................... 27 6.6 Test Results .............................................................................................................................. 27 7 EMISSION LIMITATIONS MEASUREMENT ......................................................................... 28 7.1 Test Equipment ......................................................................................................................... 28 7.2 Block Diagram of Test Setup .........…

Text truncated - open the document above for the full version.

Test Set-Up Photos 1. Conducted Emission Test 2. Radiated Electromagnetic Emission Test R ADIATED EMISSION TEST (BELOW 1GHZ) RADIATED EMISSION TEST (ABOVE 1GHZ) 3. RF Test