O4XB05

Alert IR/RF Tag - P/N ALB00001 Alert IR/RF Tag - P/N ALB00001Alert IR/RF Tag - P/N ALB00001 Alert IR/RF Tag - P/N ALB00001 Users UsersUsers Users The Alert IR/RF tag is designed for panic applications, where the user needs immediate help. Typical users are: tenants of old-age homes, staff in psychiatric wards, etc. Attachment AttachmentAttachment Attachment The Alert IR/RF tag is a key-ring device worn either attached to clothes or hung on a string or chain around the neck. IR Transmission IR TransmissionIR Transmission IR Transmission Infra-red signals are transmitted from the sides and lower section of the badge. This configuration improves the ‘visibility’ of the badge to the RDR. Operation OperationOperation Operation In general, the badge performance is similar to that of the other IR/RF badges. The button on the badge is large and easy to press.

Alert Tag Instruction Manual and Spec-Sheet FCC Compliance The F CC Wa nts Y ou to Know This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: a) Reorient or relocate the receiving antenna. b) Increase the separation between the equipment and receiver. c) Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. d) Consult the dealer or an experienced radio/TV technician. FCC Warning Modifications not expressly approved by manufacturer could void the user authority to operate the equipment under FCC rules. IR and RF Alert Tag P/N: ALB00001 (433.92 MHz) IR/RF Alert T ag Description A small light-weight, oval badge. The tag sends Infra Red signals, and in additio n sends RF signals in the frequency of 433.92 MHz. Designed especially for the convenience of the elderly or persons in stressful situations (alert, panic, etc.). General Electrical power source One 3-Volt lithium battery Data rate 19,200 bits per second Modulation ASK (Amplitude Shift Keying of IR or RF carrier) Message protocol 4 bytes proprietary format Message duration 2.08 ms Button on badge Location dependent function. Twelve identical button messages are transmitted 0.4 sec apart on every button press. Button press transmitted with IR and RF message. Button press decoded by IR and RF Readers or Central PC. Battery type CR 2032 Renata Battery life One year, assuming movement 12 hr / day Battery status indication Battery status transmitted with every RF and IR message Badge ID Unique factory programmed (ID code, transmit rate, motion sensor activation and deactivation, etc.) Dimensions Pendant shape 55 x 35 x 18 mm Weight (including battery) 25 gram Temperature: Operating -10 to 70 ° C Temperature: Storage -20 to 60 ° C Humidity: Operating Operating – 5 to 95% RH @ 70 ° C Humidity : Storage Non Operating (12 Hours) – 5 to 95% RH @ 85 ° C Accessories Neck strap (included) IR Transmission Peak optical transmitted power 500mW Peak transmission wavelength 880nm Peak radiant intensity 120 mW/Sr Frequency of transmission Carrier at 455 KHz Transmission rate During human movement – every 3 to 5 sec message. During rest (no movement) – every 60 sec Transmission angle 360 ° badge plane. ± 60 ° to badge perpendicular axis EMC compliance Refer to Appendix A and B RF Transmission 433.92 MHz RF Modulation ASK (Amplitude Shift Keying of 433.92 MHz carrier) Average effective radiated power In motion: less than –35 dbm. Motionless: less than –45 dbm Stability +/- 20ppm Peak ERP -15 dbm (max) Transmission pattern Omnidirectional Using the Alert Tag The following is a set of procedures to ensure proper use of the Alert Tag. To use the Alert Tag: 1. For general use, place the strap of the Alert Tag around the perso n’s neck. 2. In case of emergency press the large press button. Battery Replacement The battery is located inside the Alert Tag. In order to replace the battery, yo u need to open the back side of the Alert Tag with a Phillips screwdriver (preferably an electric one) with point size "0". For example, the APEX #4910. A new battery can then be inserted, after which the screw must be replaced.

Alert Tag Instruction Manual and Spec-Sheet FCC Compliance The F CC Wa nts Y ou to Know This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: a) Reorient or relocate the receiving antenna. b) Increase the separation between the equipment and receiver. c) Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. d) Consult the dealer or an experienced radio/TV technician. FCC Warning Modifications not expressly approved by manufacturer could void the user authority to operate the equipment under FCC rules. 15.9 (a) Labeling Requirements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IR and RF Alert Tag P/N: ALB00001 (433.92 MHz) IR/RF Alert T ag Description A small light-weight, oval badge. The tag sends Infra Red signals, and in additio n sends RF signals in the frequency of 433.92 MHz. Designed especially for the convenience of the elderly or persons in stressful situations (alert, panic, etc.). General Electrical power source One 3-Volt lithium battery Data rate 19,200 bits per second Modulation ASK (Amplitude Shift Keying of IR or RF carrier) Message protocol 4 bytes proprietary format Message duration 2.08 ms Button on badge Location dependent function. Twelve identical button messages are transmitted 0.4 sec apart on every button press. Button press transmitted with IR and RF message. Button press decoded by IR and RF Readers or Central PC. Battery type CR 2032 Renata Battery life One year, assuming movement 12 hr / day Battery status indication Battery status transmitted with every RF and IR message Badge ID Unique factory programmed (ID code, transmit rate, motion sensor activation and deactivation, etc.) Dimensions Pendant shape 55 x 35 x 18 mm Weight (including battery) 25 gram Temperature: Operating -10 to 70 ° C Temperature: Storage -20 to 60 ° C Humidity: Operating Operating – 5 to 95% RH @ 70 ° C Humidity : Storage Non Operating (12 Hours) – 5 to 95% RH @ 85 ° C Accessories Neck strap (included) IR Transmission Peak optical transmitted power 500mW Peak transmission wavelength 880nm Peak radiant intensity 120 mW/Sr Frequency of transmission Carrier at 455 KHz Transmission rate During human movement – every 3 to 5 sec message. During rest (no movement) – every 60 sec Transmission angle 360 ° badge plane. ± 60 ° to badge perpendicular axis EMC compliance Refer to Appendix A and B RF Transmission 433.92 MHz RF Modulation ASK (Amplitude Shift Keying of 433.92 MHz carrier) Average effective radiated power In motion: less than –35 dbm. Motionless: less than –45 dbm Stability +/- 20ppm Peak ERP -15 dbm (max) Transmission pattern Omnidirectional Using the Alert Tag The following is a set of procedures to ensure proper use of the Alert Tag. To use the Alert Tag: 1. For general use, place the strap of the Alert Tag around the perso n’s neck. 2. In case of emergency press the large press button. Battery Replacement The battery is located inside the Alert Tag. In order to replace the battery, yo u need to open the back side of the Alert Tag with a Phillips screwdriver (preferably an electric one) with point size "0". For example, the APEX #4910. A new battery can then be inserted, after which the screw must be replaced.

Alert Tag Instruction Manual and Spec-Sheet FCC Compliance The F CC Wa nts Y ou to Know This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: a) Reorient or relocate the receiving antenna. b) Increase the separation between the equipment and receiver. c) Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. d) Consult the dealer or an experienced radio/TV technician. FCC Warning Modifications not expressly approved by manufacturer could void the user authority to operate the equipment under FCC rules. 15.9 (a) Labeling Requirements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IR and RF Alert Tag P/N: ALB00001 (433.92 MHz) Feirmware ver2 IR/RF Alert T ag Description A small light-weight, oval badge. The tag sends Infra Red signals, and in additio n sends RF signals in the frequency of 433.92 MHz. Designed especially for the convenience of the elderly or persons in stressful situations (alert, panic, etc.). General Electrical power source One 3 - Volt lithium battery Data rate 19,200 bits per second Modulation ASK (Amplitude Shift Keying of IR or RF carrier) Message protocol 4 bytes proprietary format Message duration 2.08 ms Button on badge Location dependent function. Button press message transmitted on IR. Battery type CR 2032 Renata Battery life One year, assuming movement 8 hr / day Battery status indication Battery status transmitted with every RF and IR message Badge ID Unique factory programmed Dimensions Pendant shape 55 x 35 x 18 mm Weight (including battery) 25 gram Temperature: Operating -10 to 70 ° C Temperature: Storage -20 to 60 ° C Humidity: Operating Operating – 5 to 95% RH @ 70 ° C Humidity : Storage Non Operating (12 Hours) – 5 to 95% RH @ 85 ° C Accessories Neck strap (included) IR Transmission Peak optical transmitted power 500mW Peak transmission wavelength 880nm Peak radiant intensity 120 mW/Sr Frequency of transmission Carrier at 455 KHz Transmission rate Motion – every 10 sec message Motionless – every 60 sec message. Transmission angle 360 ° badge plane. ± 60 ° to badge perpendicular axis RF Transmission 433.92 MHz Modulation ASK (Amplitude Shift Keying of 433.92 MHz carrier) Transmission rate Every 10 sec message. Average ERP Effective Radiated Power - 70 dbm max Stability +/- 20ppm Peak ERP -20 dbm (max) Transmission pattern Omnidirectional Using the Alert Tag The following is a set of procedures to ensure proper use of the Alert Tag. To use the Alert Tag: 1. For general use, place the strap of the Alert Tag around the perso n’s neck. 2. In case of emergency press the large press button. Battery Replacement The battery is located inside the Alert Tag. In order to replace the battery, yo u need to open the back side of the Alert Tag with a Phillips screwdriver (preferably an electric one) with point size "0". For example, the APEX #4910. A new battery can then be inserted, after which the screw must be replaced.

October 26, 2000 11 Hasadna St., Industrial Zone, P.O.B 2571, Raanana 43650, ISRAEL Te l : 972 9 7760200 Fax: 972 9 7460593 E-mail: [email protected] Saved: 10/26/00 3:09 PM Printed: 10/26/00 3:21 PM` Shlomo Yasur Confidentiality- FCC ID O4XB05.doc Federal Communications Commission Equipment Approval Services P.O. Box 358315 Pittsburgh, PA 15251-5315 Subject: Confidentiality for FCC Application FCC ID O4XB05 Confirmation Number EA98233 of ELPAS Electro-optic Systems Ltd. Dear Madam/Sir, Due to the proprietary design developed by ELPAS Electro-optic systems Ltd. that is unique to the industry, ELPAS Electro-optic Systems Ltd. Is requesting confidentiality for the following exhibits of ELPAS Electro-optic systems Ltd.: FCC ID: O4XB05 Confirmation No.: EA98233 Report No.: E36113.01 1. Block Diagram. 2. Schematics. 3. Bill Of Materials. Please feel free to contact me with any questions. Best Regards, Shlomo Yasur V. P Engineering & Operations

ALB External Photos Figure 1 External Photo Top View Figure 2 External Photo Bottom View

Product Labeling FCC Label Location of Label on EUT

Product Labeling FCC Label Location of Label on EUT

Product Labeling FCC Label Location of Label on EUT

Internal Photo PCB 2 sides

Alert IR/RF Tag - P/N ALB00001 Alert IR/RF Tag - P/N ALB00001Alert IR/RF Tag - P/N ALB00001 Alert IR/RF Tag - P/N ALB00001 Users UsersUsers Users The Alert IR/RF tag is designed for panic applications, where the user needs immediate help. Typical users are: tenants of old-age homes, staff in psychiatric wards, etc. Attachment AttachmentAttachment Attachment The Alert IR/RF tag is a key-ring device worn either attached to clothes or hung on a string or chain around the neck. IR Transmission IR TransmissionIR Transmission IR Transmission Infra-red signals are transmitted from the sides and lower section of the badge. This configuration improves the ‘visibility’ of the badge to the RDR. Operation OperationOperation Operation In general, the badge performance is similar to that of the other IR/RF badges. The button on the badge is large and easy to press.

FCC ID O4XB05 Electrical (EMC) Test Report E36113.00ELPAS - Electro-optic Systems Ltd. Page 1 of 35 FCC DOC M Ver 1.12 04 April 2000 DATE: 16 July 2000 I.T.L. (PRODUCT TESTING) LTD. EMC Test for ELPAS - Electro-optic Systems Ltd. Equipment under test: Alert IR/RF 433 Tag ALB00001 Approved by:_____________________________ Y. Mordukhovitch , Test Engineer Approved by:_____________________________ I. Raz, EMC Laboratory Manager This report must not be reproduced, except in full, without the written permission of I.T.L. (Product Testing) Ltd. This report relates only to items tested. . FCC ID 04XB05 Test Report E36113.00ELPAS - Electro-optic Systems Ltd. Page 2 of 35 FCC DOC M Ver 1.12 04 April 2000 Measurement/Technical Report for ELPAS - Electro-optic Systems Ltd. Equipment under test: Alert IR/RF 433 Tag FCC ID: O4XB05 DATE: 16 July 2000 This report concerns:Original Grant x Class II change ___ Class B verification Class A verification Class I change ____ Equipment type: Radio Telemetry Transmitter Request Issue of Grant: x Immediately upon completion of review Limits used: CISPR 22 Part 15 x Measurement procedure used is ANSI C63.4-1992. Application for Certification Applicant for this device: prepared by:(different from "prepared by") Ishaiahou RazShlomo Yasur ITL (Product Testing) Ltd.Elpas – Electro-optic Systems Ltd. POB 21111 Hasadna St. Or Yehuda 60251Raanana 43650 IsraelIsrael Tel: 972-3-533 9022Tel: 972-9-776 0200 Fax:+972-3-5339019Fax: +972-9-746 0593 FCC ID 04XB05 Test Report E36113.00ELPAS - Electro-optic Systems Ltd. Page 3 of 35 FCC DOC M Ver 1.12 04 April 2000 TABLE OF CONTENTS 1.GENERAL INFORMATION -----------------------------------------------------------------------------4 1.1Product Description.................................................................................... 4 1.2Test Methodology...................................................................................... 5 1.3Test Facility............................................................................................... 5 1.4Measurement Uncertainty ........................................................................... 5 PRODUCT LABELING------------------------------------------------------------------------------------------6 3.SYSTEM TEST CONFIGURATION-------------------------------------------------------------------7 3.1Justification................................................................................................ 7 3.2EUT Exercise Software .............................................................................. 7 3.3Special Accessories ................................................................................... 7 3.4Equipment Modifications ............................................................................. 7 Configuration of Tested System............................................................................ 7 4.BLOCK DIAGRAM ---------------------------------------------------------------------------------------8 4.1Schematic Block/Connection Diagram.......................................................... 8 5.RADIATED EMISSION DATA --------------------------------------------------------------------------9 5.1Radiated Emission 10KHz-1000 MHz, Below 1GHz...................................... 9 5.2Measured Data.......................................................................................... 9 5.3Test Instrumentation Used, Radiated Measurements .................................. 12 5.4Field Strength Calculation ......................................................................... 13 6.RADIATED EMISSION DATA ------------------------------------------------------------------------ 14 6.1Radiated Emission Above 1 GHz............................................................... 14 6.2Test Data ................................................................................................ 14 6.3Test Instruments used, Radiated Measurement Above 1 GHZ ..................... 18 6.4Field Strength Calculation ......................................................................... 19 7.FUNDAMENTAL EMISSION BANDWIDTH-------------------------------------------------------- 20 7.1Test Specification..................................................................................... 20 7.2Test Procedure........................................................................................ 20 7.3Measured Data........................................................................................ 20 7.4Test Instrumentation Used, Fundamental Emission Band Width.................... 24 PHOTOGRAPHS OF TESTED E.U.T. --------------------------------------------------------------------- 25 9.SIGNATURES OF THE E.U.T'S TEST ENGINEERS ------------------------------------------- 29 10.APPENDIX A - CORRECTION FACTORS--------------------------------------------------------- 30 10.1 Correction factors for CABLE................................................................... 30 10.2 Correction factors for CABLE................................................................... 31 10.3 Correction factors for LOG PERIODIC ANTENNA ..................................... 32 10.4 Correction factors for BICONICAL ANTENNA............................................. 33 10.5 Correction factors for BICONICAL ANTENNA Type 3109............................ 34 10.6 Correction factors for BICONICAL ANTENNA Type 3109............................ 35 10.7 Correction factors for SAS ANTENNA, 3 meter range................................. 36 FCC ID 04XB05 Test Report E36113.00ELPAS - Electro-optic Systems Ltd. Page 4 of 35 FCC DOC M Ver 1.12 04 April 2000 1. General Information 1.1 Product Description Alert IR/RF Tag - P/N ALB00001 Users UsersUsers Users The Alert IR/RF tag is designed for panic applications, where the user needs immediate help. Typical users are: tenants of old-age homes, staff in psychiatric wards, etc. Attachment AttachmentAttachment Attachment The Alert IR/…

Text truncated - open the document above for the full version.

FCC ID O4XB05 Electrical (EMC) Test Report E36113.01ELPAS - Electro-optic Systems Ltd. Page 1 of 35 FCC DOC M Ver 1.12 04 April 2000 DATE: 16 July 2000 I.T.L. (PRODUCT TESTING) LTD. EMC Test for ELPAS - Electro-optic Systems Ltd. Equipment under test: Alert IR/RF 433 Tag ALB00001 Approved by:_____________________________ Y. Mordukhovitch , Test Engineer Approved by:_____________________________ I. Raz, EMC Laboratory Manager This report must not be reproduced, except in full, without the written permission of I.T.L. (Product Testing) Ltd. This report relates only to items tested. . FCC ID 04XB05 Test Report E36113.01ELPAS - Electro-optic Systems Ltd. Page 2 of 35 FCC DOC M Ver 1.12 04 April 2000 Measurement/Technical Report for ELPAS - Electro-optic Systems Ltd. Equipment under test: Alert IR/RF 433 Tag FCC ID: O4XB05 DATE: 16 July 2000 This report concerns:Original Grant x Class II change ___ Class B verification Class A verification Class I change ____ Equipment type: Radio Telemetry Transmitter Request Issue of Grant: x Immediately upon completion of review Limits used: CISPR 22 Part 15 x Measurement procedure used is ANSI C63.4-1992. Application for Certification Applicant for this device: prepared by:(different from "prepared by") Ishaiahou RazShlomo Yasur ITL (Product Testing) Ltd.Elpas – Electro-optic Systems Ltd. POB 21111 Hasadna St. Or Yehuda 60251Raanana 43650 IsraelIsrael Tel: 972-3-533 9022Tel: 972-9-776 0200 Fax:+972-3-5339019Fax: +972-9-746 0593 FCC ID 04XB05 Test Report E36113.01ELPAS - Electro-optic Systems Ltd. Page 3 of 35 FCC DOC M Ver 1.12 04 April 2000 TABLE OF CONTENTS 1.GENERAL INFORMATION -----------------------------------------------------------------------------4 1.1Product Description.................................................................................... 4 1.2Test Methodology...................................................................................... 5 1.3Test Facility............................................................................................... 5 1.4Measurement Uncertainty ........................................................................... 5 2.PRODUCT LABELING----------------------------------------------------------------------------------6 3.SYSTEM TEST CONFIGURATION-------------------------------------------------------------------7 3.1Justification................................................................................................ 7 3.2EUT Exercise Software .............................................................................. 7 3.3Special Accessories ................................................................................... 7 3.4Equipment Modifications ............................................................................. 7 Configuration of Tested System............................................................................ 7 4.BLOCK DIAGRAM ---------------------------------------------------------------------------------------8 4.1Schematic Block/Connection Diagram.......................................................... 8 5.RADIATED EMISSION DATA --------------------------------------------------------------------------9 5.1Radiated Emission 10KHz-1000 MHz, Below 1GHz...................................... 9 5.2Measured Data.......................................................................................... 9 5.3Test Instrumentation Used, Radiated Measurements .................................. 12 5.4Field Strength Calculation ......................................................................... 13 6.RADIATED EMISSION DATA ------------------------------------------------------------------------ 14 6.1Radiated Emission Above 1 GHz............................................................... 14 6.2Test Data ................................................................................................ 14 6.3Test Instruments used, Radiated Measurement Above 1 GHZ ..................... 18 6.4Field Strength Calculation ......................................................................... 19 7.FUNDAMENTAL EMISSION BANDWIDTH-------------------------------------------------------- 20 7.1Test Specification..................................................................................... 20 7.2Test Procedure........................................................................................ 20 7.3Measured Data........................................................................................ 20 7.4Test Instrumentation Used, Fundamental Emission Band Width.................... 24 8.PHOTOGRAPHS OF TESTED E.U.T. ------------------------------------------------------------- 25 9.SIGNATURES OF THE E.U.T'S TEST ENGINEERS ------------------------------------------- 29 10.APPENDIX A - CORRECTION FACTORS--------------------------------------------------------- 30 10.1 Correction factors for CABLE................................................................... 30 10.2 Correction factors for CABLE................................................................... 31 10.3 Correction factors for LOG PERIODIC ANTENNA ..................................... 32 10.4 Correction factors for BICONICAL ANTENNA............................................. 33 10.5 Correction factors for BICONICAL ANTENNA Type 3109............................ 34 10.6 Correction factors for BICONICAL ANTENNA Type 3109............................ 35 10.7 Correction factors for SAS ANTENNA, 3 meter range................................. 36 FCC ID 04XB05 Test Report E36113.01ELPAS - Electro-optic Systems Ltd. Page 4 of 35 FCC DOC M Ver 1.12 04 April 2000 1. General Information 1.1 Product Description Alert IR/RF Tag - P/N ALB00001 Users UsersUsers Users The Alert IR/RF tag is designed for panic applications, where the user needs immediate help. Typical users are: tenants of old-age homes, staff in psychiatric wards, etc. Attachment AttachmentAttachment Attachment The Alert IR/RF tag is a …

Text truncated - open the document above for the full version.

FCC ID O4XB05 Electrical (EMC) Test Report E36113.01ELPAS - Electro-optic Systems Ltd. Page 1 of 35 FCC DOC M Ver 1.12 04 April 2000 DATE: 16 July 2000 I.T.L. (PRODUCT TESTING) LTD. EMC Test for ELPAS - Electro-optic Systems Ltd. Equipment under test: Alert IR/RF 433 Tag ALB00001 Approved by:_____________________________ Y. Mordukhovitch , Test Engineer Approved by:_____________________________ I. Raz, EMC Laboratory Manager This report must not be reproduced, except in full, without the written permission of I.T.L. (Product Testing) Ltd. This report relates only to items tested. . FCC ID 04XB05 Test Report E36113.01ELPAS - Electro-optic Systems Ltd. Page 2 of 35 FCC DOC M Ver 1.12 04 April 2000 Measurement/Technical Report for ELPAS - Electro-optic Systems Ltd. Equipment under test: Alert IR/RF 433 Tag FCC ID: O4XB05 DATE: 16 July 2000 This report concerns:Original Grant x Class II change ___ Class B verification Class A verification Class I change ____ Equipment type: Radio Telemetry Transmitter Request Issue of Grant: x Immediately upon completion of review Limits used: CISPR 22 Part 15 x Measurement procedure used is ANSI C63.4-1992. Application for Certification Applicant for this device: prepared by:(different from "prepared by") Ishaiahou RazShlomo Yasur ITL (Product Testing) Ltd.Elpas – Electro-optic Systems Ltd. POB 21111 Hasadna St. Or Yehuda 60251Raanana 43650 IsraelIsrael Tel: 972-3-533 9022Tel: 972-9-776 0200 Fax:+972-3-5339019Fax: +972-9-746 0593 FCC ID 04XB05 Test Report E36113.01ELPAS - Electro-optic Systems Ltd. Page 3 of 35 FCC DOC M Ver 1.12 04 April 2000 TABLE OF CONTENTS 1.GENERAL INFORMATION -----------------------------------------------------------------------------4 1.1Product Description.................................................................................... 4 1.2Test Methodology...................................................................................... 5 1.3Test Facility............................................................................................... 5 1.4Measurement Uncertainty ........................................................................... 5 2.PRODUCT LABELING----------------------------------------------------------------------------------6 3.SYSTEM TEST CONFIGURATION-------------------------------------------------------------------7 3.1Justification................................................................................................ 7 3.2EUT Exercise Software .............................................................................. 7 3.3Special Accessories ................................................................................... 7 3.4Equipment Modifications ............................................................................. 7 Configuration of Tested System............................................................................ 7 4.BLOCK DIAGRAM ---------------------------------------------------------------------------------------8 4.1Schematic Block/Connection Diagram.....................................................…

Text truncated - open the document above for the full version.