OAJBA-1000UBluetooth USB Dongle

BLUEBEE - Wireless Internet Sharing Wizard - 1 - 1. Introduction 1.1. What is BLUEBEE? BLUEBEE is a Bluetooth USB adapter which provides a wireless network and Internet connection between PCs without access point and any connection cables. With BLUEBEE, you don’t need to worry any more about setting up a LAN cable or changing complex network configurations to access Internet with your laptop computer in the office or at home. PLEASE READ THROUGH THIS MANUAL BEFORE YOU USE BLUEBEE. 1.1.1. BLUEBEE Wireless Network BLUEBEE can make a wireless network, Point to Point and Multipoint connection (1 Server : 7 Clients) A wireless network consists of two sides, a Server and a Client. The Server is a PC that is directly connected to Internet through ADSL, Cable Modem or LAN. Where as the Client is a PC that can connect to Internet through the wireless network, which is provide by the Server PC, without having any direct connection sources. This manual describes, in detail, installing software, setting network configuration, software user manual, and troubleshooting. The three steps below help you configure a wireless network. A. Install PAN and EasyGate on a Server. B. Install PAN on a Client(s). C. Clients attempt to access the Server. Server: a PC with a direct connection to Internet (such as ADSL, Cable Modem, LAN, or Dial-up Modem) Client: a PC without a direct connection to Internet 1.1.2. Main features and specifications ß Wireless Internet and Data sharing ß Plug & Play USB port with high speed support ß Multi-users : Maximum seven PCs can share at the same time ß Bandwidth : Maximum 1Mbps ß Range : 100m ß Security option: Password authentication for network connection ß Specification : Bluetooth Specification 1.1 and PAN Profile V0.96E BLUEBEE - Wireless Internet Sharing Wizard - 2 - 1.2. Supplied Items ß Two Bluetooth USB Adapters ß Extension cable ß Program CD ß User Manual 1.3. System Requirements ß CPU : Pentium lll or higher is recommended. ß Memory : 64MB or higher is recommended. ß Interface ≤ Server : a LAN card, a USB port, and CD_ROM ≤ Clients : a USB port and CD_ROM ß Operating System: Windows98SE / ME / 2000 / XP BLUEBEE - Wireless Internet Sharing Wizard - 3 - 2. Installing Software In Chapter 2, a step-by-step installing guide will be given for software installation. Install PAN on both a Sever and Clients, but EasyGate on the Server only! [SERVER] 2.1. Installing PAN First, install PAN on the Server. Assuming D:\ is a CD-ROM Drive, do as follows: ß Double click on the Setup.exe icon at D:\ Pan\ Setup.exe. ß You can install the USB adapter before installing PAN, but we recommend installing the USB adapter after PAN installation is complete. 2.1.1. InstallShield wizard ß Click on “Next” button to start installation. Figure 2-1: PAN Installing Wizard BLUEBEE - Wireless Internet Sharing Wizard - 4 - 2.1.2. Software license agreement ß Click “Yes” to continue the installation if you agree to all the terms in the license agreement. Figure 2-2: Software License Agreement 2.1.3. Choose destination location ß The default location is C:\ Program Files\ IVTCorporation\ MiniBluelet\ Pan. ß Click “Next” button to install program to this folder. (Click “Browse” to select different destination folder.) Figure 2-3: Choose Destination Location BLUEBEE - Wireless Internet Sharing Wizard - 5 - 2.1.4. Windows2000 or WindowsXP configuration 2.1.4.1. Digital signature [Windows 2000 only] ß If you are using Windows 2000, it might prompt “Digital Signature Not Found” form as follows. In this case, click “Yes” to continue the installation. Figure 2-4: Digital Signature Prompt [Windows 2000] 2.1.4.2. Installing BT network adapter [Windows XP only] ß If you see similar message as [Figure 2-5] in Windows XP, click “Continue Anyway” to continue the installation. Figure 2-5: BT Network Adapter Installation Message [Windows XP] BLUEBEE - Wireless Internet Sharing Wizard - 6 - 2.1.5. InstallShield wizard complete ß If you see as [Figure 2-6], PAN is successfully installed on your computer. ß [Windows98SE / ME] User : Restarting PC is required to accept changes. ß [Windows2000 / XP] User : Restarting PC is not required. Figure 2-6: PAN Installation is Completed Note: Windows98SE / ME Users may experience a failure of locating device drivers while installing BT network adapter during the PAN software installation process. In this case, you can install the BT network adapter manually using C:\ ProgramFiles\ IVTCorporation\ MiniBluelet\ Pan\ Device\ win9x \ IVTnetBT_For98.inf Please refer to “Chapter 6. Troubleshooting” for more details. BLUEBEE - Wireless Internet Sharing Wizard - 7 - 2.1.6. PAN first run configuration Plug in USB Adapter to any empty USB port. [Windows98SE / ME ] User: After restarting PC, PAN First Run Configuration window will pop up automatically. [Windows2000 / XP] User : Double click on the PAN icon from the Desktop. ß Type user name for ‘Device Name’. (Example: BT Server, BT Client) This name will appear on the BlueNetwork list [Refer to Figure 3-1]. ß Type passkey in, and retype the passkey to confirm. ß Select the type of your device. For a notebook computer, select ‘Laptop’, and otherwise, select ‘Desktop’. ß Check mark on “Automatically start Pan” if you want to make PAN application operate immediately whenever the system is booted. ß You need to do this initial configuration only once, and the configuration is changeable. Figure 2-7: Initial PAN Configuration BLUEBEE - Wireless Internet Sharing Wizard - 8 - 2.1.7. Select work mode ß You might see a notice as [Figure2-8], if the USB Adapter is not plugged in. (If you have completed section 2.1.6 successfully, you may skip this section.) ß Make sure the USB adapter is properly plugged in, and click “Exit” button. And then run PAN application again. It might take a few minutes to configure the USB Adapter. Figure 2-8: Select Work Mode BLUEBEE - Wireless Internet Sharing Wizard - 9 - 2.2. Installing EasyGate After completing PAN insta…

Text truncated - open the document above for the full version.

From: willyauo [[email protected]] Sent: Tuesday, December 24, 2002 6:48 AM To: Mike Kuo Subject: Fw: J Communications Co., Ltd., FCC ID:OAJBA-1000U, AN02t2432 Hi Mike, I mail again. Will Yauo ----- Original Message ----- From: S. S. Liou <[email protected]> To: Mike Kuo <[email protected]> Cc: ? ?? <[email protected]> Sent: Thursday, December 19, 2002 6:51 PM Subject: Re: J Communications Co., Ltd., FCC ID:OAJBA-1000U, AN02t2432 > Hello Mike, > > Ans. #1: Please refer to attached file for test data. ET91R10-016-03p11.pdf > > Ans. #2: That is a typo. Please refer to attached file for test data. > ET91R10-016-03p12.pdf > > Ans. #3: Please refer to attached file for test data. ET91R10-016-03p13.pdf > > Ans. #4: We tested channel bandwidth again with a better sample. Please > refer to attached file for test data. ET91R10-016-03p26+27.pdf and Channel > Bandwidth.pdf > > Ans. #5: We also tested output power again. Please refer to attached file > for test data. ET91R10-016-03p30+31.pdf and Output Power.pdf > > Ans. #6: Please refer to attached revised user manual. The Tx power is 10dBm > max. Power control means the Tx power can be controlled automatically with > the maximum output power up to 10 dBm by software program. > > If there are any questions, please contact me. Thank you very much. > > Best regards, > > > S. S. Liou > ETC > > ----- Original Message ----- > From: "Mike Kuo" <[email protected]> > To: <[email protected]>; "'ETC/R00'" <[email protected]> > Sent: Saturday, November 30, 2002 9:00 AM > Subject: FW: J Communications Co., Ltd., FCC ID:OAJBA-1000U, AN02t2432 > > > > > > > > -----Original Message----- > > From: CERTADM > > Sent: Friday, November 29, 2002 4:59 PM > > To: '[email protected]' > > Subject: J Communications Co., Ltd., FCC ID:OAJBA-1000U, AN02t2432 > > > > > > Notice_content > > ------------- > > Question #1: Page 16 of test report: Peak reading is over the average > > limits. Please provide average reading. > > > > Question #2: Page 17 of test report: Peak reading is over the peak limits. > > Please address this non-compliance issue. > > > > Question #3: Page 18 of test report : Peak reading is over the average > > limits. Please provide average reading. > > > > Question #4: The 20dB Bandwidth: The limits is 1MHz. Low an middle > channel > > are reported with 20dB bandwidth greater than 1MHz. Please address this > > non-compliance issue. > > > > Question #5: When measured RF conducted output power with spectrum > analyzer, > > you used RBW=1MHz which is greater than 20dB bandwidth. Please address > this > > question and question #4 together. > > > > Question #6: In the user manual, it mentioned that the max output power is > > 20dBm with power control. Please explain what is the power control and > how > > to control the power. 20dBm does not agree with measured output power. > > Please explain. > > > > Best Regards > > > > Mike Kuo / TCB Certifier > > The items indicated above must be submitted before processing can continue > > on the above referenced application. Failure to provide the requested > > information within 60 days of the original e-mail date may result in > > application dismissal and forfeiture of the filing fee. Also, please note > > that partial responses increase processing time and should not be > submitted. > > Any questions about the content of this correspondence should be directed > to > > the e-mail address listed below the name of the sender. >

ETC Report No. : ET91R-10-016-03 Sheet 1 of 3 Sheets FCC ID. : OAJBA-1000U Rev. No 1.0 CONSTRUCTED PHOTOS of EUT 1. Front View of EUT 2. Rear View of EUT

Label information BA-1000U Photo: Bluetooth USB Adapter BA-1000U with Enclosure <Back> Label position (Size 26,8 mm x12,8 mm) From:Pei-Shan Tsai on 2002/11/25 02:49 PM To:[email protected] cc: Subject:Additional documents USB dongle (BA-1000U) Dear Tina, Please find attached the additional documents for USB dongle. The manual is quite clerer now and contains FCC information. Label size is: 26.8(W) X 12.8(H) MM Since this is quite small, on the label only FCC ID is printed. Additional information is sticked on the package material (file: label on package.pdf) and can be found in the manual. If you have further questions just reply. Additional Documents USB.zip Best regards, Pei-Shan Tsai Telecom. Group Product Safety Department TUV Rheinland Taiwan Ltd. ------------------------------------------------------- 14F, No.6, Min Chuan E. Rd., Sec. 3, Taipei 104, Taiwan, R.O.C. Tel : +886-2-2516-6040 Ext.145 Fax: +886-2-2509-7252 *************************************************** Heiko Doerschel TUEV Rheinland Korea, Ltd. Business Field Manager EMC, Telecom, Bluetooth Tel: +82 (0)2-539-1901 Fax: +82 (0)2-539-0988 Email: [email protected] Web: www.kor.tuv.com

ETC Report No. : ET91R-10-016-03 Sheet 2 of 3 Sheets FCC ID. : OAJBA-1000U Rev. No 1.0 CONSTRUCTED PHOTOS of EUT 3. Internal View of EUT 4. Component View of Main PCB ETC Report No. : ET91R-10-016-03 Sheet 3 of 3 Sheets FCC ID. : OAJBA-1000U Rev. No 1.0 CONSTRUCTED PHOTOS of EUT 5. Solder View of Main PCB

Rev. No 1.0 FCC Part 15 EMI TEST REPORT of E.U.T. : Bluetooth USB Dongle MODEL : BA-1000U FCC ID. : OAJBA-1000U for APPLICANT : J Communications Co., Ltd ADDRESS : No.124-4,Ojeon-Dong, Uiwang-City, Kyungki-Do, South Korea. Test Performed by ELECTRONICS TESTING CENTER, TAIWAN NO. 34, LIN 5, DING FU TSUN, LINKOU HSIANG, TAIPEI HSIEN, TAIWAN, R.O.C. Tel:(02)26023052, 26023054 Fax:(02)26010910 Report Number : ET91R-10-016-03 ETC Report No. : ET91R-10-016-03 FCC ID. : OAJBA-1000U Rev. No 1.0 TEST REPORT CERTIFICATION Applicant : J Communications Co., Ltd. No.124-4, Ojeon-Dong, Uiwang-City, Kyungki-Do, South Korea. Manufacturer : J Communications Co., Ltd. No.124-4, Ojeon-Dong, Uiwang-City, Kyungki-Do, South Korea. Description of EUT : a) Type of EUT : Bluetooth USB Dongle b) Trade Name : Bluebee c) Model No. : BA-1000U d) Power Supply : From PC Regulation Applied : FCC Rules and Regulations Part 15 Subpart B & C (1999) I HEREBY CERTIFY THAT: The data shown in this report were made in accordance with the procedures given in ANSI C63.4, and the energy emitted by the device was founded to be within the limits applicable. I assume full responsibility for accuracy and completeness of these data. Note: 1. The result of the testing report relates only to the item tested. 2. The testing report shall not be reproduced expect in full, without the written approval of ETC. Issued Date : Nov. 05, 2002 Test Engineer : ( Ion Lin ) Approve & Authorized Signer : Will Yauo, Manager EMC Dept. II of ELECTRONICS TESTING CENTER, TAIWAN ETC Report No. : ET91R-10-016-03 FCC ID. : OAJBA-1000U Rev. No 1.0 Table of Contents Page 1 GENERAL INFORMATION.......................................................................................................1 1.1 Product Description........................................................................................................................1 1.2 Characteristics of Device................................................................................................................1 1.3 Test Methodology..........................................................................................................................1 1.4 Test Facility....................................................................................................................................1 1.5 Modist List.....................................................................................................................................1 2 PROVISIONS APPLICABLE.......................................................................................................2 2.1 Definition........................................................................................................................................2 2.2 Requirement for Compliance...........................................................................................................3 2.3 Restricted Bands of Operation........................................................................................................5 2.4 Labeling Requirement.....................................................................................................................5 2.5 User Information............................................................................................................................6 3. SYSTEM TEST CONFIGURATION...........................................................................................7 3.1 Justification.....................................................................................................................................7 3.2 Devices for Tested System.............................................................................................................7 4 RADIATED EMISSION MEASUREMENT..............................................................................8 4.1 Applicable Standard.......................................................................................................................8 4.2 Measurement Procedure.................................................................................................................8 4.3 Measuring Instrument...................................................................................................................10 4.4 Radiated Emission Data................................................................................................................11 4.4.1 RF Portion...............................................................................................................................11 4.4.2 Other Emissions.......................................................................................................................14 4.5 Field Strength Calculation.............................................................................................................14 4.6 Photos of Radiation Measuring Setup............................................................................................15 ...........................................................................................................................................................15 5 CONDUCTED EMISSION MEASUREMENT........................................................................16 5.1 Standard Applicable.....................................................................................................................16 5.2 Measurement Procedure...............................................................................................................16 5.3 Conducted Emission Data.............................................................................................................17 5.4 Result Data Calculation.................................................................................................................19 5.5 Conducted Measurement Equipment.............................................................................................19 5.6 Photos of Conduction Measuring Setup.............…

Text truncated - open the document above for the full version.

ETC Report No. : ET91R-10-016-03 Sheet 35 of 40 Sheets FCC ID. : OAJBA-1000U Rev. No 1.0 Appendix 2 : Plotted Data for Separation of Adjacent Channel ETC Report No. : ET91R-10-016-03 Sheet 36 of 40 Sheets FCC ID. : OAJBA-1000U Rev. No 1.0 Appendix 3 : Plotted Data for Total Used Hopping Frequencies ETC Report No. : ET91R-10-016-03 Sheet 37 of 40 Sheets FCC ID. : OAJBA-1000U Rev. No 1.0 Appendix 4 : Plotted Data for Channel Bandwidth ETC Report No. : ET91R-10-016-03 Sheet 38 of 40 Sheets FCC ID. : OAJBA-1000U Rev. No 1.0 Appendix 5 : Plotted Data for Channel Dwell Time ETC Report No. : ET91R-10-016-03 Sheet 39 of 40 Sheets FCC ID. : OAJBA-1000U Rev. No 1.0 Appendix 6 : Plotted Data for Output Peak Power ETC Report No. : ET91R-10-016-03 Sheet 40 of 40 Sheets FCC ID. : OAJBA-1000U Rev. No 1.0 Appendix 7 : Plotted Data for 100 kHz Bandwidth from Band Edge

ETC Report No. : ET91R-10-016-03 Sheet 15 of 40 Sheets FCC ID. : OAJBA-1000U Rev. No 1.0 4.6 Photos of Radiation Measuring Setup ETC Report No. : ET91R-10-016-03 Sheet 20 of 40 Sheets FCC ID. : OAJBA-1000U Rev. No 1.0 5.6 Photos of Conduction Measuring Setup