OJFDMRUDPAM8Corning Everon 6000 DAS - dMRU (medium power modular remote unit) (CELL/ESMR)

Everon™ 6000 v1.0 User Manual Corning Optical Communications www.corning.com User Manual v1.0 Everon™ 6000 v1.0 User Manual User Manual v1.0 UM - Everon 6000 DAS - 1-MAR-2021 - clear of comments| March 2021 |Page 3 of 174 Preface Material About this Manual This manual describes how to install, use, configure and manage Corning’s Everon™ 6000 1.0 platform. It includes a description of the system end-to-end first time and on-going configuration, management and maintenance. Intended Users and Scope This manual is intended for Corning system installers, technicians and users. It is assumed that the user is familiar with the system and its units, and understands the basic functionality of the system. Contacting Technical Support HelpDesk Corning technical support contact information: email: [email protected] Tel: [800] 787 1266 Legal Notice Copyright Copyright © 2021 Corning., All Rights Reserved Disclaimer This document contains proprietary information of Corning and may not be reproduced in any form without the prior written consent of Corning. No part of this document may be reproduced, translated, stored in a retrieval system or transmitted in any form and by any means, electronic, mechanical, photographic, photocopying, recording, or otherwise, without the prior written permission of Corning. Information provided in this document is subject to change without notice and does not represent a commitment on the part of Corning. All products and company names are trademarks or registered trademarks of their respective holders. Software License Terms The software and the system design is the property of Corning. It is supplied to the user to be used solely for its stated purposes. It is strictly forbidden to make copies of the software or transfer it in any way, for any purpose, to any third party. The license to use the software is granted to the user only for the specific system it is installed on by Corning, or its authorized distributors and representatives. User Manual v1.0 UM - Everon 6000 DAS - 1-MAR-2021 - clear of comments| March 2021 |Page 4 of 174 The purchaser shall not modify the software in any way. It is strictly forbidden to use this product for any purpose other than originally designated for or stipulated by Corning. Conventions Important information is highlighted in a frame, as explained below: Warning : Actions requiring special attention to avoid serious bodily injury; For example, working with high voltage components Caution: Actions requiring special attention, to avoid possible damage to equipment Note: Hints and recommendations for working efficiently User Manual v1.0 UM - Everon 6000 DAS - 1-MAR-2021 - clear of comments| March 2021 |Page 5 of 174 Warranties Hardware Warranty Corning Optical Communications Wireless, Inc. (“Corning”)warrants to the original purchaser (“Customer”) that for the duration of the warranty period, one (1) year, commencing on the date of shipment of the Hardware, unless otherwise agreed in writing by Corning (the “Hardware Warranty Period”), the Hardware furnished by Corning shall be free in all material respects from defects in material and workmanship, and shall conform to the applicable portions of the Specifications, as defined below (the “Hardware Warranty”). If notified by Customer of any such defects in material or workmanship or nonconformity with applicable portions of the Specifications within the Hardware Warranty Period, Corning shall promptly, at its own election and expense, repair or replace any such Hardware proven to be defective under the terms of this Hardware Warranty. Such repair or replacement shall be Customer’s sole remedy and Corning’s sole obligation in the event this Hardware Warranty is invoked. If any components comprising a part of the Hardware are replaced or repaired during the Hardware Warranty Period, the Hardware Warranty Period for such repaired or replaced components shall extend to the longer of (i) the balance of the Hardware Warranty Period or (ii) three (3) months from the date of repair or replacement. For purposes of this Warranty, “Specifications” shall mean the specifications and performance standards of the Products as set forth in documents published by Corning and delivered to Customer which contain technical specifications or performance standards for the Products. If Customer invokes this Hardware Warranty, it shall notify Corning promptly of the claimed defect. Customer will allow Corning to inspect the Hardware at Customer’s location, or to return the Hardware to Corning’s closest repair facility. For Hardware returned to Corning’s repair facility, Customer shall be responsible for payment of all transportation and freight costs (including insurance) to Corning’s repair facility, and Corning shall be responsible for all transportation and freight costs (including insurance) incurred in connection with the shipment of such Hardware to other repair facilities of Corning and/or its return to Customer. Notwithstanding the foregoing, in no event will Corning be liable for damage to Products resulting from improper handling during or after shipment, misuse, neglect, improper installation, operation or repair (other than by authorized Corning personnel), alteration, accident, or for any other cause not attributable to defects in materials or workmanship on the part of Corning. Corning shall not reimburse or make any allowance to Customer for any labor charges incurred by Customer for replacement or repair of any goods unless such charges are authorized in advance in writing by Corning. Software Warranty Corning warrants to the original purchaser (“Customer”) that for the duration of the warranty period, one (1) year, commencing on the date of shipment of the Software, unless otherwise agreed in writing by Corning (the “Software Warranty Period”), the Software shall conform with, and perform the functions set forth in the Specifications, and shall be free from defects in material or workmanship (th…

Text truncated - open the document above for the full version.

User Manual v1.0 UM - Everon 6000 DAS - 1-MAR-2021 - clear of comments| March 2021 |Page 91 of 174 x LAN Port: 1 Gb Ethernet connection to the customer's network for remote management. By default, the port is configured to have a static IP address: 192.168.1.1; Subnet Mask: 255.255.0.0. Alternatively, the port can be configured as a DHCP client. IPv4 and IPv6 network protocols can be simultaneously supported. x INTERNAL Ports: Four RJ45, 100 Mb Ethernet ports used for management of connected ACMs. Note: Any one of these ports can also be used for a local connection if required. Default settings: IP: 10.0.0.1; Subnet Mask: 255.0.0.0 3.3 Open a Local Session Below are the instructions for opening a local management session, to perform basic system configurations via the system GUI. ¾ To Open the system GUI 1. Connect a computer (i.e., laptop) to the HCM LOCAL port via an RJ45 Cat 5 Ethernet cable, as shown below: 2. The LOCAL port is set to a static IP Address by default: 172.16.1.1; Subnet Mask: 255.255.0.0. Your laptop/tablet network parameters must be set to match the subnet of the default IP address. Note: The laptop/tablet IP address must be different than the LOCAL port IP address. Set up your laptop/tablet network parameters by following the steps below (the steps may vary slightly depending on the OS version used): Connect the computer to the LOCAL port User Manual v1.0 UM - Everon 6000 DAS - 1-MAR-2021 - clear of comments| March 2021 |Page 92 of 174 1. Go to the Control Panel and select Network and Sharing Center 2. Select Change adapter settings (in the left menu) User Manual v1.0 UM - Everon 6000 DAS - 1-MAR-2021 - clear of comments| March 2021 |Page 93 of 174 3. Right click Local Area Connection and select Properties 4. Select Internet Protocol Version 4 and click Properties The window below appears: Set the IP address according to the default IP address of the LOCAL port and the subnet mask. An example of a possible IP address is: 172.16.1.5. The IP address can't be 172.16.1.1 as this address is used by the LOCAL port. User Manual v1.0 UM - Everon 6000 DAS - 1-MAR-2021 - clear of comments| March 2021 |Page 94 of 174 3. Once the connection is established, open a browser and type-in the LOCAL port default IP address in the address bar: 172.16.1.1. The HCM Controller Log In dialog appears: 4. For first-time authentication use the following default values: x Username: admin x Password: default provided with your system. x Group: leave blank. Note: IMPORTANT! For security reasons it is highly recommended to immediately change the password (via the "Admin" -> "Security" tab) and log in again using the new password. 5. Click the "SIGN IN" button. System GUI main screen appears. User Manual v1.0 UM - Everon 6000 DAS - 1-MAR-2021 - clear of comments| March 2021 |Page 95 of 174 3.4 Screen Layout The main menu (located to the left of the window) lists all the available management options. Next to the main menu either the system tree or the corresponding sub-options are displayed. The display changes according to the option selected from the main menu. Parameters Display area System tree / sub- options Main Menu options User Manual v1.0 UM - Everon 6000 DAS - 1-MAR-2021 - clear of comments| March 2021 |Page 96 of 174 3.5 Main Menu Options The table below lists the management options provided by the main menu: Table 10: Main Menu Options Icon Enables user to... View the system topology and information about the different system elements. View all system events and generate reports. Perform initial system configurations. This option is only visible to the system administrator. Administrative options to perform system configurations, implement updates, define and monitor user's activity. View the information of the different stacks of the system. Manage the system RF channels. User Manual v1.0 UM - Everon 6000 DAS - 1-MAR-2021 - clear of comments| March 2021 |Page 97 of 174 3.6 Remote Management This section describes the configurations required for remote session access using Ethernet connection via the LAN port. At this point the system is ready to be connected to the LAN according to the instructions below. For HCM modules only – using the provided RJ45/RJ45 communication cable, connect the HCM LAN port to the corporate LAN: The LAN port is set to a static IP address by default: 192.168.1.1; Subnet Mask: 255.255.0.0. ¾ To configure the HCM LAN port 1. IMPORTANT: Make sure the HCM LAN port is connected to the corporate LAN. 2. In the main menu bar, click Æ 3. Select the IPv4 LAN Port or IPv6 LAN Port tabs and click the button. 4. The LAN port is set to a static IP address, by default: 192.168.1.1; Subnet Mask: 255.255.0.0. You may change the static IP address, subnet mask and default gateway manually to legal values. Note: make sure the values youenter in the above fields aren't used by other system elements, and are different than the default values. Multiple ACM units may be connected to a single HCM via the INTERNAL ports for management purposes. Only HCM modules should be connected to the corporate LAN. ACM modules are connected via the HCM modules. User Manual v1.0 UM - Everon 6000 DAS - 1-MAR-2021 - clear of comments| March 2021 |Page 98 of 174 Make sure the address format matches IPv4 or IPv6, according to the tab being updated. For Dynamic IP Address — set DHCP as Client, then click OK. 5. The HCM restarts after the LAN IP address is updated. 6. To open a remote management session: Open a browser and enter the LAN port IP Address in the address bar. Note: A Ping Tool option is provided to verify access to IP hosts (rather than opening another application). For more information about the ping tool and the IP Settings tab refer to section 5.1.3.6. User Manual v1.0 UM - Everon 6000 DAS - 1-MAR-2021 - clear of comments| March 2021 |Page 99 of 174 4. Initial Commissioning This section describes all the initial configurations that must be done by the system administrator. 4.1 Create new …

Text truncated - open the document above for the full version.

FCC Attestation Letter January 21, 2021 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Attestation letter per KDB 935210 D02 Clause 4 paragraph d for FCC ID: OJFDMRUDPAM8 Warning label message will be also shown in online and point-of-sale marketing materials and on the outside packing of device. Thank you Company: Corning Optical Communications Wireless Authorized Signature: Printed Name: Isaac Nisaan Date: January 21, 2021

January 21, 2021 To: Timco Engineering Inc. To Whom It May Concern We hereby authorize Mr. Ilan Cohen of I.T.L. (Product Testing) Ltd (ITL) to sign Form 731 on our behalf regarding the FCC Certification Process for the following application: FCC ID: OJFDMRUDPAM8 Thank you Company: Corning Optical Communications Wireless Authorized Signature: Printed Name: Isaac Nisaan Date: January 21, 2021

January 21, 2021 To: Timco Engineering Inc. To Whom It May Concern We hereby authorize Mr. Ilan Cohen of I.T.L. (Product Testing) Ltd (ITL) to act on our behalf regarding the FCC Certification Process for the following application: FCC ID: OJFDMRUDPAM8 Thank you Company: Corning Optical Communications Wireless Authorized Signature: Printed Name: Isaac Nisaan Date: January 21, 2021

January 21, 2021 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: OJFDMRUDPAM8 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Long Term: a. CONF APPENDIX D-MRU CELL ESMR OJFDMRUDPAM8 Schem.pdf b. CONF APPENDIX D-MRU CELL ESMR OJFDMRUDPAM8 PartLst.pdf c. CONF APPENDIX D-MRU CELL ESMR OJFDMRUDPAM8 BlkDia.pdf d. CONF APPENDIX D-MRU CELL ESMR OJFDMRUDPAM8 OpDes.pdf e. CONF APPENDIX D-MRU CELL ESMR OJFDMRUDPAM8 TunPro.pdf Short Term – 180 Days: a. CONF APPENDIX D-MRU CELL ESMR OJFDMRUDPAM8 UserMan.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Thank you Date: January 21, 2021

FCC ID AND Booster Warning Labels

Labels Sample

R.F Exposure/Safety Calculation for FCC ID: OJFDMRUDPAM8 (CELL ESMR) The E.U.T. is rack or wall mounted. The typical distance between the E.U.T. and the general population is >120cm. Calculation of Maximum Permissible Exposure (MPE) Based on Section 1.1310 Requirements (a) FCC limit at 878MHz is: f/1500 = 0.5853 mW/cm 2 Using table 1 of Section 1.1310 limit for general population/uncontrolled exposures, the above level is an average over 30 minutes. (c)The power density produced by the E.U.T. is P t - Transmitted Peak Power (worst case) G T - Antenna Gain (worst case) , 12.5dBi= 17.8 numeric R- Distance from Transmitter 120 cm ( d ) Peak power density at worst case continuous transmission: generation Modulation Pt (dBm) Pt (W) Antenna type G T (dBi) G T numeric R (cm) S AV (mW/cm 2 ) Limit (mW/cm 2 ) 5G 16QAM 33.51 2.244 External 12.5 17.8 120 0.22073 0.5853 64QAM 33.21 2.094 External 12.5 17.8 120 0.20598 0.5853 256QAM 33.96 2.489 External 12.5 17.8 120 0.24483 0.5853 QPSK 34.51 2.825 External 12.5 17.8 120 0.27788 0.5853 4G 16QAM 34.30 2.692 External 12.5 17.8 120 0.26480 0.5853 64QAM 34.65 2.917 External 12.5 17.8 120 0.28693 0.5853 QPSK 35.44 3.499 External 12.5 17.8 120 0.34418 0.5853 3G WCDMA 34.03 2.535 External 12.5 17.8 120 0.24936 0.5853 BAND-CELL/ESMR ( e) This is below the FCC limit. 2 4R GP S tt π =

Test Report E220860.00 Corning Optical Communication Wireless Page 1 of 164 FCC ACC M Ver 1.1 05Mayl 2000 DATE: 24 February 2021 I.T.L. (PRODUCT TESTING) LTD. FCC Radio Test Report For Corning Optical Communication Wireless Equipment under test: Corning Everon 6000 DAS - dMRU dMRU Medium Power Modular Remote Unit (CELL/ESMR) Tested by: _____________________________ M. Zohar Approved by: _____________________________ D. Shidlowsky This report must not be reproduced, except in full, without the written permission of I.T.L. (Product Testing) Ltd. This report relates only to items tested. Test Report E220860.00 Corning Optical Communication Wireless Page 2 of 164 FCC ACC M Ver 1.1 05Mayl 2000 Measurement/Technical Report for Corning Optical Communication Wireless Corning Everon 6000 DAS - dMRU dMRU Medium Power Modular Remote Unit (CELL/ESMR) FCC ID: OJFDMRUDPAM8 This report concerns: Original Grant: X Class II change: Class I change: Equipment type: Part 20 Industrial Booster (CMRS) Limits used: 47CFR Parts 2; 27 Measurement procedure used is KDB 935210 D05 v01r04 April 2020 and ANSI IEEE C63.26-2015 Substitution Method used as in ANSI TIA-603-E-2016 Application for Certification Applicant for this device: prepared by: (different from "prepared by") R. Pinchuck Isaac Nissan ITL (Product Testing) Ltd. Corning Optical Communication Wireless 1 Bat Sheva St. 8253 1 st Avenue Lod 7120101 Vienna, VA 22812 Israel U.S.A. e-mail [email protected] Tel: +1-703 855-1773 e-mail: [email protected] Test Report E220860.00 Corning Optical Communication Wireless Page 3 of 164 FCC ACC M Ver 1.1 05Mayl 2000 TABLE OF CONTENTS 1 GENERAL INFORMATION --------------------------------------------------------------------------- 5 1.1 Administrative Information ........................................................................... 5 1.2 List of Accreditations ................................................................................... 6 1.3 Product Description ..................................................................................... 7 1.4 Test Methodology ........................................................................................ 7 1.5 Test Facility ................................................................................................. 7 1.6 Measurement Uncertainty ........................................................................... 7 2 SYSTEM TEST CONFIGURATION ----------------------------------------------------------------- 8 2.1 Justification .................................................................................................. 8 2.2 EUT Exercise Software ............................................................................... 8 2.3 Special Accessories .................................................................................... 8 2.4 Equipment Modifications ............................................................................. 8 2.5 Configuration of Tested System .................................................................. 9 3 TEST SET-UP PHOTOS ----------------------------------------------------------------------------- 11 4 RF POWER OUTPUT - 5G -------------------------------------------------------------------------- 14 4.1 Test Specification ...................................................................................... 14 4.2 Test Procedure .......................................................................................... 14 4.3 Test Limit ................................................................................................... 14 4.4 Test Results............................................................................................... 14 4.5 Test Equipment Used; Channel Power ..................................................... 32 5 RF POWER OUTPUT – 3G AND 4G ------------------------------------------------------------- 33 5.1 Test Specification ...................................................................................... 33 5.2 Test Procedure .......................................................................................... 33 5.3 Test Limit ................................................................................................... 33 5.4 Test Results............................................................................................... 33 5.5 Test Equipment Used; Channel Power ..................................................... 42 6 BAND EDGE SPECTRUM - 5G ------------------------------------------------------------------- 43 6.1 Test Specification ...................................................................................... 43 6.2 Test Procedure .......................................................................................... 43 6.3 Test Limit ................................................................................................... 43 6.4 Test Results............................................................................................... 43 6.5 Test Equipment Used; Band Edge Spectrum ........................................... 54 7 BAND EDGE SPECTRUM – 3G AND 4G ------------------------------------------------------- 55 7.1 Test Specification ...................................................................................... 55 7.2 Test Procedure .......................................................................................... 55 7.3 Test Limit ................................................................................................... 55 7.4 Test Results............................................................................................... 55 7.5 Test Equipment Used; Band Edge Spectrum ........................................... 61 8 OCCUPIED BANDWIDTH – 5G ------------------------------------------------------------------- 62 8.1 Test Specification ...................................................................................... 62 8.2 Test Procedure ....................…

Text truncated - open the document above for the full version.

Test Report E220860.00 Corning Optical Communication Wireless Page 118 of 164 FCC ACC M Ver 1.1 05Mayl 2000 Figure 388: Spurious Emissions at Antenna Terminal 16QAM, 867.0MHz, B.W. 10MHz, Sub Carrier 15kHz Figure 389: Spurious Emissions at Antenna Terminal 16QAM, 878.0MHz, B.W. 10MHz, Sub Carrier 15kHz Figure 390: Spurious Emissions at Antenna Terminal 16QAM, 889.0MHz, B.W. 10MHz, Sub Carrier 15kHz I.T.L.-Israel Testing Laboratries FCC Part 27 and Part 2 Spurious emissions 867MHz 9.0K100.0K1.0M10.0M100.0M1.0G10.0G Frequency (Hz) -100.0 -80.0 -60.0 -40.0 -20.0 0 20.0 50.0 Amplitude (dBm) Operator: A.Shelly Company name - CORNING Model name - DMRU P/N - Modulation - 16QAM BW - 10MHz I.T.L.-Israel Testing Laboratries FCC Part 27 and Part 2 Spurious emissions 878MHz 9.0K100.0K1.0M10.0M100.0M1.0G10.0G Frequency (Hz) -100.0 -80.0 -60.0 -40.0 -20.0 0 20.0 50.0 Amplitude (dBm) Company Name: CORNINGOperator: A.Shelly Company name - CORNING Model name - DMRU P/N - Modulation - 16QAM BW - 10MHz I.T.L.-Israel Testing Laboratries FCC Part 27 and Part 2 Spurious emissions 889MHz 9.0K100.0K1.0M10.0M100.0M1.0G10.0G Frequency (Hz) -100.0 -80.0 -60.0 -40.0 -20.0 0 20.0 50.0 Amplitude (dBm) Company Name: CORNINGOperator: A.Shelly Company name - CORNING Model name - DMRU P/N - Modulation - 16QAM BW - 10MHz Test Report E220860.00 Corning Optical Communication Wireless Page 119 of 164 FCC ACC M Ver 1.1 05Mayl 2000 Figure 391: Spurious Emissions at Antenna Terminal 16QAM, 867.0MHz, B.W. 10MHz, Sub Carrier 30kHz Figure 392: Spurious Emissions at Antenna Terminal 16QAM, 878.0MHz, B.W. 10MHz, Sub Carrier 30kHz Figure 393: Spurious Emissions at Antenna Terminal 16QAM, 889.0MHz, B.W. 10MHz, Sub Carrier 30kHz I.T.L.-Israel Testing Laboratries FCC Part 27 and Part 2 Spurious emissions 867MHz 9.0K100.0K1.0M10.0M100.0M1.0G10.0G Frequency (Hz) -100.0 -80.0 -60.0 -40.0 -20.0 0 20.0 50.0 Amplitude (dBm) Operator: A.Shelly Company name - CORNING Model name - DMRU P/N - Modulation - 16QAM BW - 10MHz I.T.L.-Israel Testing Laboratries FCC Part 27 and Part 2 Spurious emissions 878MHz 9.0K100.0K1.0M10.0M100.0M1.0G10.0G Frequency (Hz) -100.0 -80.0 -60.0 -40.0 -20.0 0 20.0 50.0 Amplitude (dBm) Company Name: CORNINGOperator: A.Shelly Company name - CORNING Model name - DMRU P/N - Modulation - 16QAM BW - 10MHz I.T.L.-Israel Testing Laboratries FCC Part 27 and Part 2 Spurious emissions 889MHz 9.0K100.0K1.0M10.0M100.0M1.0G10.0G Frequency (Hz) -100.0 -80.0 -60.0 -40.0 -20.0 0 20.0 50.0 Amplitude (dBm) Company Name: CORNINGOperator: A.Shelly Company name - CORNING Model name - DMRU P/N - Modulation - 16QAM BW - 10MHz Test Report E220860.00 Corning Optical Communication Wireless Page 120 of 164 FCC ACC M Ver 1.1 05Mayl 2000 Figure 394: Spurious Emissions at Antenna Terminal 16QAM, 869.5MHz, B.W. 15MHz, Sub Carrier 15kHz Figure 395: Spurious Emissions at Antenna Terminal 16QAM, 878.0MHz, B.W. 15MHz, Sub Carrier 15kHz Figure 396: Spurious Emissions at Antenna Terminal 16QAM, 886.5MHz, B.W. 15MHz, Sub Carrier 15kHz I.T.L.-Israel Testing Laboratries FCC Part 27 and Part 2 Spurious emissions 869.5MHz 9.0K100.0K1.0M10.0M100.0M1.0G10.0G Frequency (Hz) -100.0 -80.0 -60.0 -40.0 -20.0 0 20.0 50.0 Amplitude (dBm) Operator: A.Shelly Company name - CORNING Model name - DMRU P/N - Subcarrier - 15KHz Modulation - QPSK BW - 15MHz I.T.L.-Israel Testing Laboratries FCC Part 27 and Part 2 Spurious emissions 878MHz 9.0K100.0K1.0M10.0M100.0M1.0G10.0G Frequency (Hz) -100.0 -80.0 -60.0 -40.0 -20.0 0 20.0 50.0 Amplitude (dBm) Company Name: CORNINGOperator: A.Shelly Company name - CORNING Model name - DMRU P/N - Subcarrier - 15KHz Modulation - QPSK BW - 15MHz I.T.L.-Israel Testing Laboratries FCC Part 27 and Part 2 Spurious emissions 886.5MHz 9.0K100.0K1.0M10.0M100.0M1.0G10.0G Frequency (Hz) -100.0 -80.0 -60.0 -40.0 -20.0 0 20.0 50.0 Amplitude (dBm) Company Name: CORNINGOperator: A.Shelly Company name - CORNING Model name - DMRU P/N - Subcarrier - 15KHz Modulation - QPSK BW - 15MHz Test Report E220860.00 Corning Optical Communication Wireless Page 121 of 164 FCC ACC M Ver 1.1 05Mayl 2000 Figure 397: Spurious Emissions at Antenna Terminal 16QAM, 869.5MHz, B.W. 15MHz, Sub Carrier 30kHz Figure 398: Spurious Emissions at Antenna Terminal 16QAM, 878.0MHz, B.W. 15MHz, Sub Carrier 30kHz Figure 399: Spurious Emissions at Antenna Terminal 16QAM, 869.5MHz, B.W. 15MHz, Sub Carrier 30kHz I.T.L.-Israel Testing Laboratries FCC Part 27 and Part 2 Spurious emissions 869.5MHz 9.0K100.0K1.0M10.0M100.0M1.0G10.0G Frequency (Hz) -100.0 -80.0 -60.0 -40.0 -20.0 0 20.0 50.0 Amplitude (dBm) Operator: A.Shelly Company name - CORNING Model name - DMRU P/N - Subcarrier - 30KHz Modulation - 16QAM BW - 15MHz I.T.L.-Israel Testing Laboratries FCC Part 27 and Part 2 Spurious emissions 878MHz 9.0K100.0K1.0M10.0M100.0M1.0G10.0G Frequency (Hz) -100.0 -80.0 -60.0 -40.0 -20.0 0 20.0 50.0 Amplitude (dBm) Company Name: CORNINGOperator: A.Shelly Company name - CORNING Model name - DMRU P/N - Subcarrier - 30KHz Modulation - 16QAM BW - 15MHz I.T.L.-Israel Testing Laboratries FCC Part 27 and Part 2 Spurious emissions 886.5MHz 9.0K100.0K1.0M10.0M100.0M1.0G10.0G Frequency (Hz) -100.0 -80.0 -60.0 -40.0 -20.0 0 20.0 50.0 Amplitude (dBm) Company Name: CORNINGOperator: A.Shelly Company name - CORNING Model name - DMRU P/N - Subcarrier - 30KHz Modulation - 16QAM BW - 15MHz Test Report E220860.00 Corning Optical Communication Wireless Page 122 of 164 FCC ACC M Ver 1.1 05Mayl 2000 Figure 400: Spurious Emissions at Antenna Terminal 64QAM, 864.5MHz, B.W. 5MHz, Sub Carrier 15kHz Figure 401: Spurious Emissions at Antenna Terminal 64QAM, 878.0MHz, B.W. 5MHz, Sub Carrier 15kHz Figure 402: Spurious Emissions at Antenna Terminal 64QAM, 891.5MHz, B.W. 5MHz, Sub Carrier 15kHz I.T.L.-Israel Testing Laboratries FCC Part 27 and Part 2 Spurious emissions864.5MHz 9.0K100.0K1.0M10.0M100.0M1.0G10.0G Frequency (Hz) -100.0 -80.0 -60.0 -40.0 -20.0 0 20.0 50.0 Amplitude (dBm) Operator: A.Shelly Company name - CORNING Model name - DM…

Text truncated - open the document above for the full version.

Test Report E220860.00 Corning Optical Communication Wireless Page 142 of 164 FCC ACC M Ver 1.1 05Mayl 2000 Figure 454: Spurious Emissions at Antenna Terminal 16QAM, 864.5MHz, B.W. 5MHz Figure 455: Spurious Emissions at Antenna Terminal 16QAM, 878.0MHz, B.W. 5MHz Figure 456: Spurious Emissions at Antenna Terminal 16QAM, 891.5MHz, B.W. 5MHz I.T.L.-Israel Testing Laboratries FCC Part 27 and Part 2 Spurious emissions864.5MHz 9.0K100.0K1.0M10.0M100.0M1.0G10.0G Frequency (Hz) -100.0 -90.0 -80.0 -70.0 -60.0 -50.0 -40.0 -30.0 -20.0 -10.0 0 10.0 20.0 30.0 40.0 50.0 Amplitude (dBm) Operator: A.Shelly Company name - CORNING Model name - DMRU P/N - Modulation - 16QAM BW - 5MHz I.T.L.-Israel Testing Laboratries FCC Part 27 and Part 2 Spurious emissions 878MHz 9.0K100.0K1.0M10.0M100.0M1.0G10.0G Frequency (Hz) -100.0 -90.0 -80.0 -70.0 -60.0 -50.0 -40.0 -30.0 -20.0 -10.0 0 10.0 20.0 30.0 40.0 50.0 Amplitude (dBm) Company Name: CORNINGOperator: A.Shelly Company name - CORNING Model name - DMRU P/N - Modulation - 16QAM BW - 5MHz I.T.L.-Israel Testing Laboratries FCC Part 27 and Part 2 Spurious emissions 891.5MHz 9.0K100.0K1.0M10.0M100.0M1.0G10.0G Frequency (Hz) -100.0 -90.0 -80.0 -70.0 -60.0 -50.0 -40.0 -30.0 -20.0 -10.0 0 10.0 20.0 30.0 40.0 50.0 Amplitude (dBm) Company Name: CORNINGOperator: A.Shelly Company name - CORNING Model name - DMRU P/N - Modulation - 16QAM BW - 5MHz Test Report E220860.00 Corning Optical Communication Wireless Page 143 of 164 FCC ACC M Ver 1.1 05Mayl 2000 Figure 457: Spurious Emissions at Antenna Terminal 16QAM, 867.0MHz, B.W. 10MHz Figure 458: Spurious Emissions at Antenna Terminal 16QAM, 878.0MHz, B.W. 10MHz Figure 459: Spurious Emissions at Antenna Terminal 16QAM, 889.0MHz, B.W. 10MHz I.T.L.-Israel Testing Laboratries FCC Part 27 and Part 2 Spurious emissions 867MHz 9.0K100.0K1.0M10.0M100.0M1.0G10.0G Frequency (Hz) -100.0 -90.0 -80.0 -70.0 -60.0 -50.0 -40.0 -30.0 -20.0 -10.0 0 10.0 20.0 30.0 40.0 50.0 Amplitude (dBm) Operator: A.Shelly Company name - CORNING Model name - DMRU P/N - Modulation - 16QAM BW - 10MHz I.T.L.-Israel Testing Laboratries FCC Part 27 and Part 2 Spurious emissions 878MHz 9.0K100.0K1.0M10.0M100.0M1.0G10.0G Frequency (Hz) -100.0 -90.0 -80.0 -70.0 -60.0 -50.0 -40.0 -30.0 -20.0 -10.0 0 10.0 20.0 30.0 40.0 50.0 Amplitude (dBm) Company Name: CORNINGOperator: A.Shelly Company nam…

Text truncated - open the document above for the full version.