ONJ-MDR2400ETDigital Radio

MDR2400 and MDR5800 User Manual 862-01881 Issue 8 Page 1 MDR2400 and MDR5800 Digital Radio User Manual Document Number: 862-01881 MDR2400 and MDR5800 User Manual 862-01881 Issue 8 Page 2 Issue Status Issue Revised Pages/Amendments 1 1 2 31 3 2 4 General – terminology definition PER used instead of BER to remove interpretation ambiguity between Block Error Rate and Bit Error Rate. Note Block (equivalent to packet) concept is still maintained within sections describing G.826 parameters to maintain consistency with G.826 terminology. 5 MIB Description chapter added, RESET Button Additions, chapter on setup of a serial connection between a PC/Laptop and the Element Management Port, IP network address description diagrams. 6 Amendments related to customer furnished equipment, Outdoor Unit temperature range update, Maintenance and Ordering section updates, Appendix added regarding Antennas. 7 Update on RESET Button functionality description, MIB definition additions, product receive sensitivity level adjustment, FCC notice updates (Warning – this page, Antenna Information – Appendix E), NMS picture update. Appendix D Indoor Unit firmware Upgrade Notice added. Appendix B MIB Elements ResetAllRFPerfomanceData and ResetAllG826 deprecated. 8 Added detail for new MDR2400 Outdoor Unit Added detail for new Indoor Unit – balanced and unbalanced connectors FEDERAL COMMUNICATIONS COMMISSION NOTICE The equipment has been tested and found to comply with the limits for a Class A digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. WARNING- To comply with FCC RF exposure limits, the antennas for this transmitter must be fix-mounted to provide a separation distance of 2 meters (6.6 ft) or more from all persons to satisfy RF exposure requirements. This equipment must be professionally installed. Note The MDR2400 frequency output must be limited to between 2412MHz and 2458MHz and the power to a maximum of +18dBm for the recommended antennas for compliance to FCC standards, U.S. only. INDUSTRY CANADA NOTICE This device has been designed to operate with an antenna having a maximum gain of 42 dB. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Exposure of Humans to RF Fields The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's website: www.hc-sc.gc.ca/rpb MDR2400 and MDR5800 User Manual 862-01881 Issue 8 Page 3 Publication Number: 862-01881 Issue 8 June 2002 © 1999 Tellumat (Pty) Limited The information contained herein is the property of Tellumat (Pty) Limited and is supplied without liability for errors or omissions. No part may be reproduced, used or disclosed except as authorised by contract or other written permission. The copyright and the foregoing restriction on reproduction, use and disclosure extend to all media in which this information may be embodied, including magnetic or electronic storage etc. MDR2400 and MDR5800 User Manual 862-01881 Issue 8 Page 4 Table of Contents Page 1 INTRODUCTION 9 1.1 MDR2400 and MDR5800 Description 9 2 TECHNICAL DESCRIPTION 11 2.1 System Overview 11 2.2 Outdoor Unit 11 2.2.1 Frequency plans 11 2.2.2 RF Power Output Options 14 2.2.3 MDR2400 and MDR5800 Outdoor Units 14 2.3 Indoor Unit 15 2.3.1 Payload Interface Options 15 2.3.2 Reset/Configuration Button 16 2.3.3 Service (Wayside) Serial Data Channel 17 2.3.4 Element Manager Port 18 2.3.5 10BaseT Ethernet RJ45 Port 18 2.3.6 IU/OU Link LED 18 2.3.7 IU/OU Data Interconnect RJ45 18 2.3.8 IU/OU Power Interconnect 19 2.3.9 Auxiliary In/Out Port 19 2.3.10 DC Power Input 19 2.3.11 Fuse Holder 19 2.3.12 ON/OFF Switch 19 2.3.13 Ground Terminal 19 3 PLANNING 21 3.1 System Type Selection 21 3.1.1 Antenna selection (MDR5800) 21 3.1.2 Antenna selection (MDR2400) 21 3.2 Site Evaluation 22 3.3 Multipath Effects 22 3.4 Interference Considerations 23 3.5 Microcell Backhaul Applications of MDR Digital Radios 24 MDR2400 and MDR5800 User Manual 862-01881 Issue 8 Page 5 3.5.1 Setting the Transmitted Power Levels 24 3.5.2 Frequency Multiplexing 24 3.5.3 Antenna Isolation 24 4 INSTALLATION 26 4.1 Customer Furnished Tools and Equipment 27 4.2 Indoor Unit 28 4.2.1 Introduction 28 4.2.2 Installing the Indoor Unit in a Rack 28 4.2.3 Connecting a DC Power Supply 29 4.2.4 Balanced Payload Data 30 4.2.5 Unbalanced Payload Data 31 4.2.6 Connecting Auxiliary In/Out (Optional) 31 4.2.7 Connecting the Service (Wayside) Serial Channel (Optional) 32 4.2.8 Connecting the Element Manager Port 32 4.3 Outdoor Unit 33 4.3.1 MDR Outdoor Unit 33 4.4 Interconnection Cable Installation 34 4.4.1 INTE…

Text truncated - open the document above for the full version.

MDR2400 and MDR5800 User Manual 862-01881 Issue 8 Page 1 MDR2400 and MDR5800 Digital Radio User Manual Document Number: 862-01881 MDR2400 and MDR5800 User Manual 862-01881 Issue 8 Page 2 Issue Status Issue Revised Pages/Amendments 1 1 2 31 3 2 4 General – terminology definition PER used instead of BER to remove interpretation ambiguity between Block Error Rate and Bit Error Rate. Note Block (equivalent to packet) concept is still maintained within sections describing G.826 parameters to maintain consistency with G.826 terminology. 5 MIB Description chapter added, RESET Button Additions, chapter on setup of a serial connection between a PC/Laptop and the Element Management Port, IP network address description diagrams. 6 Amendments related to customer furnished equipment, Outdoor Unit temperature range update, Maintenance and Ordering section updates, Appendix added regarding Antennas. 7 Update on RESET Button functionality description, MIB definition additions, product receive sensitivity level adjustment, FCC notice updates (Warning – this page, Antenna Information – Appendix E), NMS picture update. Appendix D Indoor Unit firmware Upgrade Notice added. Appendix B MIB Elements ResetAllRFPerfomanceData and ResetAllG826 deprecated. 8 Added detail for new MDR2400 Outdoor Unit Added detail for new Indoor Unit – balanced and unbalanced connectors FEDERAL COMMUNICATIONS COMMISSION NOTICE The equipment has been tested and found to comply with the limits for a Class A digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. WARNING- To comply with FCC RF exposure limits, the antennas for this transmitter must be fix-mounted to provide a separation distance of 2 meters (6.6 ft) or more from all persons to satisfy RF exposure requirements. This equipment must be professionally installed. Note The MDR2400 frequency output must be limited to between 2412MHz and 2458MHz and the power to a maximum of +22dBm (2412-2426MHz) and +18dBm (2458MHz) for the recommended antennas for compliance to FCC standards, U.S. only. INDUSTRY CANADA NOTICE This device has been designed to operate with an antenna having a maximum gain of 42 dB. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Exposure of Humans to RF Fields The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's website: www.hc-sc.gc.ca/rpb MDR2400 and MDR5800 User Manual 862-01881 Issue 8 Page 3 Publication Number: 862-01881 Issue 8 June 2002 © 1999 Tellumat (Pty) Limited The information contained herein is the property of Tellumat (Pty) Limited and is supplied without liability for errors or omissions. No part may be reproduced, used or disclosed except as authorised by contract or other written permission. The copyright and the foregoing restriction on reproduction, use and disclosure extend to all media in which this information may be embodied, including magnetic or electronic storage etc. MDR2400 and MDR5800 User Manual 862-01881 Issue 8 Page 4 Table of Contents Page 1 INTRODUCTION 9 1.1 MDR2400 and MDR5800 Description 9 2 TECHNICAL DESCRIPTION 11 2.1 System Overview 11 2.2 Outdoor Unit 11 2.2.1 Frequency plans 11 2.2.2 RF Power Output Options 14 2.2.3 MDR2400 and MDR5800 Outdoor Units 14 2.3 Indoor Unit 15 2.3.1 Payload Interface Options 15 2.3.2 Reset/Configuration Button 16 2.3.3 Service (Wayside) Serial Data Channel 17 2.3.4 Element Manager Port 18 2.3.5 10BaseT Ethernet RJ45 Port 18 2.3.6 IU/OU Link LED 18 2.3.7 IU/OU Data Interconnect RJ45 18 2.3.8 IU/OU Power Interconnect 19 2.3.9 Auxiliary In/Out Port 19 2.3.10 DC Power Input 19 2.3.11 Fuse Holder 19 2.3.12 ON/OFF Switch 19 2.3.13 Ground Terminal 19 3 PLANNING 21 3.1 System Type Selection 21 3.1.1 Antenna selection (MDR5800) 21 3.1.2 Antenna selection (MDR2400) 21 3.2 Site Evaluation 22 3.3 Multipath Effects 22 3.4 Interference Considerations 23 3.5 Microcell Backhaul Applications of MDR Digital Radios 24 MDR2400 and MDR5800 User Manual 862-01881 Issue 8 Page 5 3.5.1 Setting the Transmitted Power Levels 24 3.5.2 Frequency Multiplexing 24 3.5.3 Antenna Isolation 24 4 INSTALLATION 26 4.1 Customer Furnished Tools and Equipment 27 4.2 Indoor Unit 28 4.2.1 Introduction 28 4.2.2 Installing the Indoor Unit in a Rack 28 4.2.3 Connecting a DC Power Supply 29 4.2.4 Balanced Payload Data 30 4.2.5 Unbalanced Payload Data 31 4.2.6 Connecting Auxiliary In/Out (Optional) 31 4.2.7 Connecting the Service (Wayside) Serial Channel (Optional) 32 4.2.8 Connecting the Element Manager Port 32 4.3 Outdoor Unit 33 4.3.1 MDR Outdoor Unit 33 4.4 Interconnect…

Text truncated - open the document above for the full version.

Rhein Tech Laboratories Report number 2002006 360 Herndon Parkway, Suite 1400 FCC Part 15.247 Herndon, VA 20170 Industry Canada RSS-210 FCC ID ONJ-MDR2400ET http://www.rheintech.com Page 41 of 54 APPENDIX F: ATTESTATION LETTERS (IF APPLICABLE) Please see the following page.

Rhein Tech Laboratories Report number 2002006 360 Herndon Parkway, Suite 1400 FCC Part 15.247 Herndon, VA 20170 Industry Canada RSS-210 FCC ID ONJ-MDR2400ET http://www.rheintech.com Page 40 of 54 APPENDIX E: CONFIDENTIALITY REQUEST LETTER (IF APPLICABLE) Please see the following page. Tellumat (Pty) Limited 64-74 White Rd Retreat Cape Town South Africa * PO Box 30451, Tokai 7966 South Africa DIRECTORS: Dr. J.A. Temple (Chairman), L.C. Jones (Managing), P.B. Hobbs, C.J. Meintjes, R.J. Shaw, Dr. S. Sibisi, J. de V. van Zyl, M. Higgins, K.A. Alborough (Alt), J.W. Grobler (Alt), M.D. Chewins (Alt) Registration Number: 96/00957/07 Tel: +27 21 710-2911 Fax: +27 21 712-1278 e-mail: [email protected] Web: http://www.tellumat.com 11 December 2001 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: The following information is to be held confidential pursuant of 47 CFR Part 0 §0.457 and Section 552(b)(4) of the Freedom of Information Act, because the information provided contains trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Schematics Product Description Yours faithfully For Tellumat (Pty) Limited Dr Douw van der Merwe Technical Director Broadband Wireless Block Diagrams

Rhein Tech Laboratories Report number 2002006 360 Herndon Parkway, Suite 1400 FCC Part 15.247 Herndon, VA 20170 Industry Canada RSS-210 FCC ID ONJ-MDR2400ET http://www.rheintech.com Page 39 of 54 APPENDIX D: AGENCY AUTHORIZATION LETTER Please see the following page. Tellumat (Pty) Limited 64-74 White Rd Retreat Cape Town South Africa * PO Box 30451, Tokai 7966 South Africa DIRECTORS: Dr. J.A. Temple (Chairman), L.C. Jones (Managing), P.B. Hobbs, C.J. Meintjes, R.J. Shaw, Dr. S. Sibisi, J. de V. van Zyl, M. Higgins, K.A. Alborough (Alt), J.W. Grobler (Alt), M.D. Chewins (Alt) Registration Number: 96/00957/07 Tel: +27 21 710-2911 Fax: +27 21 712-1278 e-mail: [email protected] Web: http://www.tellumat.com 19 February 2001 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: Please be advised that Tellumat (Pty) Limited authorizes Rhein Tech Laboratories, Inc. to act on our behalf, until otherwise notified, for applications submitted to the above competent body. We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug abuse ACT of 1988, U.S.C. 682 and as defined in 47 CFR Part 1 §1.2002(b). Yours faithfully For Tellumat (Pty) Limited Dr Douw van der Merwe Technical Director Broadband Wireless

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 RE: FCC ID: ONJ-MDR2400ET Attention: Desmond Fraser I have a few comments on this Application. 1 The report limits the max output at 2458MHz to 18dBm; and the 731 states that the highest frequency is 2458MHz. However, the manual states that the device operates at 1MHz steps in two sub-band arrangements of 2410-2426 MHz and 2458-2474MHz. The report states that the software power selection will be limited to 18dBm at 2458 MHz. However, while the manual instructs the technician to adjust the power to match the receive levels using existing software, neither the manual nor the technical documentation states how the manufacturer tune up procedure sets this level to begin with. Please provide evidence that the maximum power level at 2458 MHz is tuned by the manufacturer to be no greater than 18dBm. 2 Please correct the manual to state only the 2458MHz frequency in the higher sub-band is used. 3 Since this is a Part 15 device the label requirements should be met. The FCC ID label for a Part 15 device is to include the two condition statement when size and other restrictions are not a concern. The size of the device is sufficiently large enough to allow the two condition statement on the FCC ID label on the device. Please explain why the label does not contain the FCC ID label as required in 15.19. For example, is it the manufacturers contention that under 15.19(a)(5) the device is of such use as not to be practicable? Dennis Ward mailto:[email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

June 20, 2002 To: Dennis Ward, ATCB RE: FCC ID: ONJ-MDR2400ET Correspondence I have a few comments on this Application. 1. The report limits the max output at 2458MHz to 18dBm; and the 731 states that the highest frequency is 2458MHz. However, the manual states that the device operates at 1 MHz steps in two sub-band arrangements of 2410-2426MHz and 2458-2474MHz. The report states that the software power selection will be limited to 18dBm at 2458MHz. However, while the manual instructs the technician to adjust the power to match the receive levels using existing software, neither the manual nor the technical documentation states how the manufacturer tune up procedure sets this level to begin with. Please provide evidence that the maximum power level at 2458MHz is tuned by the manufacturer to be no greater than 18dBm. Response : Please refer to the revised manual uploaded today. Page 2 (see Note), page 14 (2.2.2) and page 22 (Table 6) have been modified to address this issue. The manufacturer has customers who do not reside in FCC countries, and would like to have the added frequency and power range. Therefore, the manual revisions were made so that the FCC compliancy restrictions are clearly marked. 2. Please correct the manual to state only the 2458MHz frequency in the higher sub-band is used. Response : Please refer to the revised manual uploaded today. Page 13 (2.2.1.3) and 14, and page 42 (Table, see first parameter) have been modified to address this issue. 3. Since this is a Part 15 device the label requirements should be met. The FCC ID label for a Part 15 device is to include the two-condition statement when size and other restrictions are not a concern. The size of the device is sufficiently large enough to allow the two-condition statement on the FCC ID label on the device. Please explain why the label does not contain the FCC ID label as required in 15.19. For example, is it the manufacturers contention that under 15.19(a)(5) the device is of such use as not to be practicable? Response : The manufacturer included this statement in the manual, and believed that to be sufficient. A revised label has been uploaded for your review.

Rhein Tech Laboratories Report number 2002006 360 Herndon Parkway, Suite 1400 FCC Part 15.247 Herndon, VA 20170 Industry Canada RSS-210 FCC ID ONJ-MDR2400ET http://www.rheintech.com Page 49 of 54 APPENDIX N: EXTERNAL PHOTOGRAPHS Outdoor Unit Front Outdoor Unit Back Outdoor Unit Bottom Outdoot Unit Side On Gland Housing Lid Inside IU front –120 Ohm D-type connection IU Back Indoor Unit with Cover Removed

Rhein Tech Laboratories Report number 2002006 360 Herndon Parkway, Suite 1400 FCC Part 15.247 Herndon, VA 20170 Industry Canada RSS-210 FCC ID ONJ-MDR2400ET http://www.rheintech.com Page 43 of 54 APPENDIX H: LABEL AND LABEL LOCATION Label Placement: FCC ID Label on Back of Outdoor Unit FCC ID Sample Label with FCC ID

Rhein Tech Laboratories Report number 2002006 360 Herndon Parkway, Suite 1400 FCC Part 15.247 Herndon, VA 20170 Industry Canada RSS-210 FCC ID ONJ-MDR2400ET http://www.rheintech.com Page 50 of 54 APPENDIX O: INTERNAL PHOTOGRAPHS Outdoor Unit without Front Cover Outdoor Unit with no Baseband Processor Assembly Baseband Processor Top Assembly with Cans Baseband Processor Bottom Assembly Baseband Processor Side Assembly Baseband Processor PCB Top with Screening Can

Baseband Processor PCB Bottom with Screening Can Baseband Processor PCB Bottom without Screening Can

PSU/TCXO Top Assembly with Screening Can PSU/TCXO Top Assembly without Screening Can

PSU/TCXO Bottom Assembly with Screening Can PSU/TCXO Bottom Assembly without Screening Can

Power Amplifier Power Amplifier with Lid Removed Rx Housing Rx Housing with Lid Removed Rx Housing Bottom View Rx Housing Lid Ribbon to Feedthrough PCB

Tx Housing Tx Housing with Lid Removed Tx Housing Bottom View Tx Housing Lid Lightning Protection PCB External Cable Interface PCB External Cable Interface and Lightning Protection Assembly Spectrum Analyser PCB – top and bottom Indoor Unit Component Side Indoor Unit Solder Side

Rhein Tech Laboratories Report number 2002006 360 Herndon Parkway, Suite 1400 FCC Part 15.247 Herndon, VA 20170 Industry Canada RSS-210 FCC ID ONJ-MDR2400ET http://www.rheintech.com Page 35 of 54 APPENDIX A: RF EXPOSURE From FCC 1.1310 table 1A, the maximum permissible RF exposure for an uncontrolled environment is 1mW/cm 2. The Electric field generated for a 1mW/cm 2 exposure (S) is calculated as follows: S = E 2 /Z where: S = Power density E = Electric field Z = Impedance. E = √S x Z 1mW/cm 2 = 10 W/m 2 The impedance of free space is 337 ohms, where E and H fields are perpendicular. Thus: E = √10 x 377 = 61.4 V/m which is equivalent to 1mW/cm 2 Using the relationship between Electric field E, Power in watts P, and distance in meters d, the corresponding Antenna numeric gain G and the transmitter output power and solving for d, d = √ P eak x 30 x G E The Numeric gain G of antenna with a gain specified in dB is determined by: G = Log –1 (dB gain/10). The table below identifies the distances where the 1mW/cm 2 exposure limits may be exceeded during continuous transmission using the proposed fixed antennas Manufacturer Type Model Gain (dBi) Numeric gain Operating Frequency (MHz) Peak Power (mW) Calculated Distance (m) Minimum RF Exposure Separation Distance (m) Gabriel Electronics P ARABOLIC ANTENNA SSG4-23 27.1 512.9 2412 199.5 0.9 2 Rhein Tech Laboratories Report number 2002006 360 Herndon Parkway, Suite 1400 FCC Part 15.247 Herndon, VA 20170 Industry Canada RSS-210 FCC ID ONJ-MDR2400ET http://www.rheintech.com Page 36 of 54 WARNING: It is the responsibility of the professional installer to ensure that when using the outdoor antenna kits in the United States (or where FCC rules apply), only the antenna specified above may be used. The use of any other antenna is expressly forbidden in accordance with FCC rules CFR47 part 15.204. Notice: FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment when installed as directed. This equipment should be installed and operated with the Gabriel Electronics SSG4-23 in a fixed-mount configuration, installed with a minimum of 2 meters of separation distance between the antenna and all persons during normal operation.

Engineering and Testing for EMC and Safety Compliance 360 Herndon Parkway, Suite 1400 Herndon, VA 20170 Phone: 703-689-0368; Fax: 703-689-2056; Metro: 703-471-6441 CERTIFICATION APPLICATION REPORT FCC PART 15.247 CERTIFICATION & INDUSTRY CANADA CERTIFICATION Test Lab: Rhein Tech Laboratories, Inc. Phone: 703-689-0368 360 Herndon Parkway Fax: 703-689-2056 Suite 1400 Web Site: www.rheintech.com Herndon, VA 20170 E-Mail :[email protected] Applicant Information: Tellumat (Pty) Ltd Phone: 27-21-7102911 Contact: Johann Gerber Fax: 27-21-7121278 64-74 White Road E-Mail: [email protected] Retreat, 7945 South Africa FCC ID: ONJ-MDR2400ET RTL WORK ORDER NUMBER: 2002006 MODEL(S): MDR2400 ET4 Outdoor Unit (M/N: 651-03905) MDR MTE Indoor Unit (M/N: 651-03810) RTL QUOTE NUMBER: QRTL01-1219 DATE OF TEST REPORT: June 12, 2002 Standards and Procedures: FCC 97-114 (DSSS), ANSI C63.4, ANSI/TIA/EIA603 and ANSI/TIA/EIA603-1 FCC Classification: DSS Direct Sequence Spread Spectrum FCC Rule Part(s): Part 15.247: Operation within the bands 920-928 MHz, 2400-2483.5 MHz and 5725-5850 MHz Direct Sequence System Industry Canada Standard: RSS-210: Low Power License-Exempt Radio Communication Devices (All Frequency Bands) Digital Interface Information Digital Interface was found to be compliant Receiver Information Receiver was found to be compliant Frequency Range (MHz) Output Power (W) Freq. Tolerance Emission Designator 2412-2458 0.1995 N/A N/A We, the undersigned, hereby declare that the equipment tested and referenced in this report conforms to the identified standard(s) as described in this test report. No modifications were made to the equipment during testing in order to achieve compliance with these standards. Furthermore, there was no deviation from, additions to, or exclusions from the FCC Part 2, FCC Part 15, FCC 97-114 (DSSS), Industry Canada RSS-210, ANSI C63.4, ANSI/TIA/EIA603 and ANSI/TIA/EIA603-1. Signature: Date: June 12, 2002 Typed/Printed Name: Desmond A. Fraser Position: President Rhein Tech Laboratories Report number 2002006 360 Herndon Parkway, Suite 1400 FCC Part 15.247 Herndon, VA 20170 Industry Canada RSS-210 FCC ID ONJ-MDR2400ET http://www.rheintech.com Page 2 of 54 TABLE OF CONTENTS 1 GENERAL INFORMATION ............................................................................................................................................................................ 5 1.1 SCOPE .......................................................................................................................................................................... 5 1.2 TEST FACILITY .......................................................................................................................................................... 5 1.3 RELATED SUBMITTAL(S)/GRANT(S)..................................................................................................................... 5 2 TEST INFORMATION..................................................................................................................................................................................... 6 2.1 TEST JUSTIFICATION ............................................................................................................................................... 6 2.2 EXERCISING THE EUT .............................................................................................................................................. 6 2.3 TEST RESULT SUMMARY ........................................................................................................................................ 6 2.4 TEST SYSTEM DETAILS ........................................................................................................................................... 7 2.5 CONFIGURATION OF TESTED SYSTEM ................................................................................................................ 8 3 COMPLIANCE WITH THE RESTRICTED BAND EDGE - §15.205 .............................................................................................................. 9 3.1 TEST PROCEDURE..................................................................................................................................................... 9 3.2 RESTRICTED BAND EDGE PLOTS .......................................................................................................................... 9 4 CONDUCTED LIMITS - §15.207 .................................................................................................................................................................. 11 4.1 TEST METHODOLOGY FOR CONDUCTED EMISSIONS MEASUREMENTS .................................................. 11 4.2 CONDUCTED EMISSION TEST PROCEDURE...................................................................................................... 11 4.3 CONDUCTED EMISSION TEST DATA .................................................................................................................. 12 5 RADIATED EMISSION FOR RECEIVER/DIGITAL INTERFACE - §15.209 ............................................................................................... 18 5.1 RADIATED EMISSION TEST PROCEDURE FOR RECEIVER/DIGITAL INTERFACE ..................................... 18 5.2 RADIATED EMISSION TEST DATA RECEIVER/DIGITAL INTERFACE .......................................................... 18 6 RADIATED EMISSIONS/RADIATED HARMONICS/SPURIOUS NOISE - §15.247 ................................................................................... 19 6.1 RADIATED EMISSION TEST PROCEDURE FOR HARMONICS/SPURIOUS NOISE........................................ 19 6.2 RADIATED EMISSIONS HARMONICS/SPURIOUS TEST DATA ....................................................................... 19 6.3 TEST EQUIPMENT USED FOR TESTING .............................................................................................................. 21 7 MODULATED BANDWIDTH - §1…

Text truncated - open the document above for the full version.

Rhein Tech Laboratories Report number 2002006 360 Herndon Parkway, Suite 1400 FCC Part 15.247 Herndon, VA 20170 Industry Canada RSS-210 FCC ID ONJ-MDR2400ET http://www.rheintech.com Page 48 of 54 APPENDIX M: TEST PHOTOGRAPHS PHOTOGRAPH 1: RADIATED BACK VIEW PHOTOGRAPH 2: RADIATED FRONT VIEW