OU4XG1000XANBOO REMOTE MONITORING AND ACCESS GATEWAY

X1000 FIRST TIME SET-UP /// 2 I FIRST TIME SET-UP /// THERE ARE TWO BASIC STEPS TO THE FIRST TIME SET UP: 1. Registering your Gateway with the website. 2. Discover devices and register with the Gateway. Click ‘NEXT’ to begin Step 1. To register your Gateway with the website, you will need the User Name and Registration Token. This information is provided to you when you create your account at http://ces.xanboo.us or the website in which you are registering your Gateway. ■ Input the User Name and Registration Token in the corresponding fields. ■ Click on the ‘REGISTER GATEWAY’ button to begin registration. Note: Registration may take up to 30 seconds. Once your Gateway has successfully been registered, you may begin the second portion of the first time set-up process DEVICE DISCOVERY by clicking on the ‘NEXT’ button. Upon hitting ‘NEXT’, you will be instructed to plug in your wired cameras and push the discover button on your devices. All Homesight products work with the X1000 HomeGenie system. Each wireless device (sensors, repeaters) has a Discover button. To begin the device discovery process, you must press the discover button (a device discovery tool is provided with each Homesight product). This must be pressed while Discovery is in progress in order to be Discovered to the Gateway. After you press the Discovery button on a device you will see a listing informing you that your Gateway has detected a wireless device and that the registration is in progress. Once the device has been successfully registered, it will appear in the Device list. The discover process will run until either all devices or discovered, or 15 minutes has elapsed. Click ‘NEXT’ to proceed. IP CAMERA REGISTRATION PAGE: Should you wish to register a IP Camera, click on the link IP Camera Registration Page . 4 3 Automatic detection of Panasonic IP cameras on your LAN: TO DISCOVER NEW PANASONIC IP CAMERAS YOU HAVE TO: 1. Reset the camera to factory defaults by pushing the reset button at the bottom of the camera. 2. Disconnect and reconnect back power to the camera after the reset operation. 3. Click ‘CONTINUE’. This will bring you back to the discovery page. Once you have discovered all the devices for your Gateway click on the ‘NEXT’ button at the bottom of the page to complete the first time set up process. You may then click the ‘MONITOR DEVICES’ button. NAVIGATION BAR /// From the Homesight Navigation Bar you will have access to your entire account with various functions. ■ Monitor: Allows the user to glance at the system status of your devices. ■ Base Unit: Allows the user to arm/disarm devices. ■ Device Setup: Select this option to discover additional devices. ■ Account: Provides registration information, as well as preferences for your temperature units. ■ Access Keys: A listing of all the wireless keys, discovered to your account. ■ Event Log: Monitors all actions associated with your X1000. MONITOR: Clicking ‘MONITOR DEVICES’ (last step of set up wizard), or ‘MONITOR’ from the Homesight Navigation Bar will provide you access to view the administrative page listing all of your devices. Note: Device testing and status update may take 30 seconds or more. Please allow enough time for the page to load. FROM THE MONITOR PAGE YOU CAN DETERMINE: ■ Which devices have been discovered ■ Current device status ■ Power and/or DC % ■ QoS ■ Ability to refresh To refresh the status of a particular device, click the ‘REFRESH’ button. The user of this account clicked refresh on Switch 789B and received the following message on the bottom of the screen: 6 5 The message will disappear about 30 seconds after the refresh is complete. Click on the Name of the Device to change settings and configurations. See DEVICE SETUP for more instructions. BASE UNIT: You will have the options of arming or disarming all devices. Once you select the time frame parameters in which to arm the devices (now, 1min, 5min, 10min, 15min, 30min), click ‘APPLY’ . You may also disarm all devices now by clicking ‘DISARM NOW’. DEVICES ARE ARMED DEVICES ARE DISARMED DEVICE SETUP: Aside from viewing a listing of all of the devices associated with a particular X1000 account, by clicking ‘CONFIGURE’ option, customers will be presented with control options and setting for a particular device. Depending upon the device, customers clicking the ‘CONFIGURE’ button may have access to change some of the following settings amongst others: ■ Device Name ■ Armed Status ■ Power Modes ■ Temperature Thresholds To make changes click ‘APPLY’. Doing so will result in a message stating Changes applied successfully. Click ‘CONTINUE’ to come back to the Monitor page. ACCOUNT: The best way to obtain Gateway registration information is to click on the ‘ACCOUNT’ tab from the HomeGenie navigation bar.   Information such as registered user name, the ability to un-register your gateway, and editing temperature preferences are presented here. ■ To Un-Register Your Gateway: click ‘REMOVE FROM SERVICE’. ■ To Change the Temperature Preferences From Fahrenheit to Celsius: select the desired preference from the drop down menu, and click ‘SELECT TEMPERATURE UNITS’. ■ If You Change an Option: a new page will appear, click ‘CONTINUE’. You will be brought back to the Monitor section. ACCESS KEYS: View and control all registered keys used with access panels. These keys will allow those with access the ability to arm and disarm all devices upon entry into the home or business. Click ‘APPLY’. You will see Changes applied successfully. Click ‘CONTINUE’. To go back to the Access Keys page to note changes. To keep track of changes, simply look at the SERIAL # field. This number will match the serial number on the actual wireless key. Should a key need to be deleted for any reason click delete. A verification pop-up will appear. Click ‘OK’ if you are sure, and wish to proceed. EVENT LOG: The Event Logs alert the user all actions associated with your account, click the ‘EVENT LOG’ tab from the Homesigh…

Text truncated - open the document above for the full version.

EUT - Front View EUT - Back View Adapter - Front View Adapter - Back View

FCC ID Label Sample for Model: XG1000S FCC ID: OU4XG1000 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

FCC ID Label This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation The Label must not be a stick-on paper. The Label on these products must be permanently affixed to the product and readily visible at the time of purchase and must last the expected lifetime of the equipment not be readily detachable. Proposed Label Location on EUT EUT Bottom View/proposed FCC Mark Location FCC ID: OU4XG1000 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause

PCB1 - Front View PCB1- Back View PCB2- Front View PCB2- Back View PCB3- Front View PCB3- Back View

X1000 May, 24, 2006 Architecture X1000 Gateway hardware architecture is shown in Figure 1. It is based on the microprocessor Au1550 which is a versatile high-performance, low-power, high integration security network system-on-a-chip (SOC) designed for wired and wireless applications where security is important. This security network processor accelerates networking applications such as gateways and network addressable storage (NAS) units, wireless access points, and voice over internet Protocol environments. The network processor is a complete SOC based on the MIPS32 instruction set and runs at Linux operating system. It integrate a variety of periphery interface, including interrupt control, DMA controller, PCI interface, USB host, I2C, SPI, SRAM controller, DDR/SDR SDRAM controller, UART, 10/100 Ethernet MAC,GPIO, 32-Bit PCI interface and so on. CC1000 is a true single chip UHF transceiver designed for very low power and low voltage wireless communications with sensors. It operates at 418MHz and 433MHz frequency by programmed different firmware via an easy-to-interface serial bus with a microcontroller.

Brief description of AFM2 protocol and operation All Xanboo products have a uniform communication protocol. The only variation within the range of products is the method of trigger and operation The communication protocol: Modulation: FSK Manchester encoded 50kHz swing. Duration: less than 20 mS. The code structure: A Preamble, followed by device class ID, device serial. number and trigger code Frequency: 418 MHz Operation Cycle :Typical operational cycle for all devices is anticipated to be less than four per day when Armed. In most cases when the premises are occupied the system is unarmed. Operation XWS50M When this device is Armed and a movement is detected, the device sends one packet of code as above and then goes back to the sleep mode to conserve battery. The devise has a minimum silent time of:10s before it can be triggered again. XPC240 This device can be commanded to Turn on a load connected to it via the above code structure. It acknowledges the command and activates the load. XWC900 The motion detector in this device, when Armed, turns the Camera section on causing it to send an analogue video signal (Via the 2.4 GHz transmitter) to the Gateway. This is preceded with one packet of code in accordance with the above structure. This device can also be turned on Via the Gateway in a similar fashion. XSC501 This device sends one packet of code in accordance with the above protocol every time it is triggered. This can be initiated by a door opening, detection of moisture or similar event. This device also has the ability to transmit ambient temperature within the same code structure. XWC700 The operation of this product is identical to XWC 900. Mehrdad Ghalebi 6/22/04

PCB1 - Front View PCB1- Back View PCB2- Front View PCB2- Back View PCB3- Front View PCB3- Back View

FCC TEST REPORT Page 1 of 31 FCC ID : OU4XG1000 Applicant : Xanboo Inc 115 West 30 th Street, 6 th Floor New York , NY10001 Equipment Under Test (EUT) : Product description : Xanboo Remote Monitoring and access Gateway Model No. : XG1000S Standards : FCC 15 Subpart C Paragraph 15.231 Date of Test : July 06, 2006 Test Engineer : Tiger Su Reviewed By : PERPARED BY: Waltek Services (Shenzhen) Co., Ltd. 8C,West Tower, Aidi Building, No.5003 Binhe Rd, Futian District, Shenzhen518045, Guangdong, China. Tel: 86-755-83551033 Fax: 86-755-83552400 Xanboo Inc FCC ID:OU4XG1000 Page 2 of 31 2 Contents Page 1 COVER PAGE..........................................................................................................................................................1 2 CONTENTS ..............................................................................................................................................................2 3 TEST SUMMARY....................................................................................................................................................5 4 GENERAL INFORMATION..................................................................................................................................6 4.1 CLIENT INFORMATION............................................................................................................................................6 4.2 GENERAL DESCRIPTION OF E.U.T...........................................................................................................................6 4.3 DETAILS OF E.U.T. .................................................................................................................................................6 4.4 DESCRIPTION OF SUPPORT UNITS...........................................................................................................................6 4.5 STANDARDS APPLICABLE FOR TESTING..................................................................................................................6 4.6 TEST FACILITY........................................................................................................................................................7 4.7 TEST LOCATION......................................................................................................................................................7 5 EQUIPMENT USED DURING TEST ...................................................................................................................8 6 CONDUCTED EMISSION TEST ..........................................................................................................................9 6.1 TEST EQUIPMENT....................................................................................................................................................9 6.2 TEST PROCEDURE...................................................................................................................................................9 6.3 CONDUCTED TEST SETUP.....................................................................................................................................10 6.4 EUT OPERATING CONDITION...............................................................................................................................10 6.5 CONDUCTED EMISSION LIMITS.............................................................................................................................11 6.6 CONDUCTED EMISSION TEST DATA......................................................................................................................12 6.7 CONDUCTIED EMISSIONS TEST DATA...................................................................................................................14 7 RADIATION EMISSION TEST...........................................................................................................................15 7.1 TEST EQUIPMENT..................................................................................................................................................15 7.2 MEASUREMENT UNCERTAINTY.............................................................................................................................15 7.3 TEST PROCEDURE.................................................................................................................................................15 7.4 RADIATED TEST SETUP.........................................................................................................................................16 7.5 SPECTRUM ANALYZER SETUP...............................................................................................................................16 7.6 CORRECTED AMPLITUDE & MARGIN CALCULATION............................................................................................17 7.7 SUMMARY OF TEST RESULTS................................................................................................................................17 7.8 EUT OPERATING CONDITION...............................................................................................................................18 7.9 RADIATED EMISSIONS LIMIT.................................................................................................................................18 7.10 RADIATED EMISSIONS TEST RESULT................................................................................................................19 7.10.1 Radiated Emission Data.............................................................................................................................19 8 PERIODIC OPERATION .....................................................................................................................................21 9 BAND EDGE .................................................................................................................................................…

Text truncated - open the document above for the full version.

Conduction Emission Test View Radiation Emission Test View For 30MHz-1000MHz Radiation Emission Test View For 1GHz-5GHz