P9M-LASORXPhottix Laso TTL Flash Trigger Receiver

Phottix Laso TTL Flash Trigger_Receiver Thank you for purchasing a Phottix Product. Note: Before using the Phottix Laso Wireless Trigger, please read this instruction manual carefully, while also referring to the instruction manuals of your camera, flash and other relevant devices. Warnings 1. This product is a precise electronic instrument. Do not expose to damp environments or dust. 2. Please shut down the power of all devices when installing the wireless trigger. 3. Do not drop or crush. 4. Do not use the wireless trigger at flammable, explosive or high temperature environment. 5. Do not use harsh chemicals or solvents to clean the body. Use a soft cloth or lens paper. 6. Remove batteries from the wireless trigger if not being used for an extended period. 7. Interference: The Phottix Laso wireless trigger transmits radio signals at 2.4GHz. Its performance can be affected by electrical current, magnetic fields, radio signals, wireless routers, cellular phones, and other electronic devices. Environmental objects, such as large buildings or walls, trees, fences, or cars can also affect transmission performance. If your wireless trigger can’t be triggered, move its location slightly. FCC Interference Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the followingtwo conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Phottix Laso TTL FLash Trigger For Canon/Receiver The Phottix Laso receiver is used with non-wireless Canon ETTL Speedlites to perform wireless radio-receiving control and triggering function. The receiver is compatible with multiple wireless radio transmitting devices, including the Phottix Laso transmitter, Canon ST-E3-RT Speedlite transmitter, and radio-enabled Canon Speedlites. Table of Contents I. Parts II. Preparation Before Use III. The LCD Display IV. Wireless Flash Shooting: Radio Transmission V. Trouble Shooting Guide I.Parts 1. Radio transmission confirmation lamp 2. LCD panel 3. Power button 4. Function button 1 5. Function button 2 6. Function button 3 7. Function button 4 8. Test flash button 9. Hot shoe mount 10. Batter compartment 11. Cold shoe/Tripod lug 12. Locking ring 13. 5V DC power port 14. 3.5mm output port 15. USB port II. Preparation before Use Installing the batteries 1. Press the battery compartment cover and slide it down as shown to open the battery cover. 2. Insert the batteries. Make sure the “+” and“-”battery contacts are correctly oriented as shown. (Note: Please use 2 pieces of AA alkaline batteries or AA type NI-MH batteries. 3. Replace the battery cover and push back into the locked position. 4. When the power icon on the LCD screen displays insufficient power, replace the batteries with new ones. Attaching and Removing the Phottix Laso receiver Attaching the flash to the Phottix Laso receiver 1. Align the flash’s hot shoe and the Phottix Laso receiver’s hot shoe mount. 2. Slide the flash all the way into the Phottix Laso receiver’s hot shoe mount 3. Lock the flash with the flash’s locking mechanism. Removing the flash 1. Release the lock of flash according to its locking mechanism（see picture） 2. Slide the flash out of the Phottix Laso receiver’s hot shoe mount. 1 2 Turn On/Off the Phottix Laso receiver 1. Turn On: Press and hold the power button until MENU interface is displayed on screen. 2. Turn off: Press and hold the power button until the LCD screen goes blank. Checking Version Info on the Phottix Laso Receiver You can check the present version information on the Phottix Laso receiver: While pressing power button to turn on the Phottix Laso receiver, press function button 1, 2 or 3 spontaneously until relevant version info is displayed on the LCD screen. Function button 1, 2 and 3 is respectively corresponding to base hardware & software version, RF hardware & software info, and Icon version. Test Firing: The Phottix Laso receiver supports test firing function. You can trigger the flash attached to the Phottix Laso receiver by pressing test button <> on the receiver. Attaching the Phottix Laso receiver to studio lights or flashes by cable 1) Turn off the flash/strobe and the Phottix Laso receiver 2) Connect a cable to the receiver’s 3.5 mm output port 3) Connect the opposite end of the cable to a flash or studio strobe 4) Turn on the flash/strobe and the Phottix Laso receiver 5) Set the flash to Manual mode – no ETTL functions can be used when a compatible flash is triggered by cable. Lock function While the Phottix Laso receiver is on, press and hold power…

Text truncated - open the document above for the full version.

R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:P9M-LASORX page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F15158 11-1 11. PHOTOGRAPH OF EUT Figure 1 General Appearance of the EUT Figure 2 General Appearance of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:P9M-LASORX page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F15158 11-2 Figure 3 General Appearance of the EUT Figure 4 General Appearance of the EUT

对外产品名称和型号LIST 对外产品名称对外产品型号FCCID 号码 发射器 Phottix Laso TTL Flash Trigger Transmitter Laso (T) P9M-LASOTX 接收器 Phottix Laso TTL Flash Trigger Receiver Laso (R) P9M-LASORX 商标仕样: FCCID 标签的仕样: FCCID 标签的位置仕样:

R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:P9M-LASORX page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F15158 11-3 Figure 5 Inside of the EUT Figure 6 Inside of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:P9M-LASORX page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F15158 11-4 Figure 7 Inside of the EUT Figure 8 Component Side of the PCB R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:P9M-LASORX page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F15158 11-5 Figure 9 Component Side of the PCB Figure 10 Component Side of the PCB R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:P9M-LASORX page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F15158 11-6 Figure 11 Component Side of the PCB Figure 12 Component Side of the PCB R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:P9M-LASORX page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F15158 11-7 Figure 13 Flash Cable

R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:P9M-LASORX page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F15158 8-1 8. RADIO FRREQUENCY EXPOSURE COMPLIANCE RESULT : PASS Test standard : FCC KDB Publication 447498 D01 V05 Since maximum peak output power of the transmitter is<10mW, i.e.0.009346mW<10mW, hence the EUT is excluded from SAR evaluation according to FCC KDB Publication 447498 D01:General RF Exposure Guidance V05.

R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:P9M-LASORX Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F15158 FCC PART 15C TEST REPORT FOR CERTIFICATION On Behalf of Phottix (HK) Ltd. Phottix Laso TTL Flash Trigger Receiver Brand Name Model No. Phottix Laso (R) FCC ID: P9M-LASORX Prepared for : Phottix (HK) Ltd. 10/F Block A, Yip Fat Factory Building, Phase 1, 77 Hoi Yuen Rd, Kwun Tong, KIn, Hong Kong Prepared By : Audix Technology (Shenzhen) Co., Ltd. No. 6, Ke Feng Rd., 52 Block, Shenzhen Science & Industrial Park, Nantou, Shenzhen, Guangdong, China Tel: (0755) 26639496 Report Number ACS-F15158 Date of Test Feb.13~28, 2015 Date of Report Jun.04, 2015 R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:P9M-LASORX Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F15158 TABLE OF CONTENTS Description Page 1. SUMMARY OF STANDARDS AND RESULTS.......................................................... 1-1 1.1. Description of Standards and Results .................................................................................. 1-1 2. GENERAL INFORMATION ......................................................................................... 2-1 2.1. Description of Device (EUT) ............................................................................................... 2-1 2.2. Tested Supporting System Details ....................................................................................... 2-2 2.3. EUT Configuration and operation conditions for test.......................................................... 2-2 2.4. Test Facility ......................................................................................................................... 2-3 2.5. Measurement Uncertainty (95% confidence levels, k=2) .................................................... 2-3 3. POWER LINE CONDUCTED EMISSION TEST ....................................................... 3-1 3.1. Test Equipment .................................................................................................................... 3-1 3.2. Block Diagram of Test Setup ............................................................................................... 3-1 3.3. Power Line Conducted Emission Test Limits...................................................................... 3-1 3.4. Configuration of EUT on Test ............................................................................................. 3-1 3.5. Operating Condition of EUT................................................................................................ 3-2 3.6. Test Procedure...................................................................................................................... 3-2 3.7. Conducted Disturbance at Mains Terminals Test Results.................................................... 3-2 4. RADIATED EMISSION TEST ...................................................................................... 4-1 4.1. Test Equipment .................................................................................................................... 4-1 4.2. Block Diagram of Test Setup ............................................................................................... 4-2 4.3. Radiated Emission Limit Standard: FCC 15.209 and 15.249 .............................................. 4-3 4.4. EUT Configuration on Test.................................................................................................. 4-3 4.5. Operating Condition of EUT................................................................................................ 4-3 4.6. Test Procedure...................................................................................................................... 4-3 4.7. Radiated Emission Test Results ........................................................................................... 4-4 5. 20 DB BANDWIDTH TEST ........................................................................................... 5-1 5.1. Test Equipment .................................................................................................................... 5-1 5.2. Limit..................................................................................................................................... 5-1 5.3. Test Results .......................................................................................................................... 5-1 6. BAND EDGE COMPLIANCE TEST ............................................................................ 6-1 6.1. Test Equipment .................................................................................................................... 6-1 6.2. Limit..................................................................................................................................... 6-1 6.3. Test Produce ......................................................................................................................... 6-1 6.4. Test Results .......................................................................................................................... 6-1 7. ANTENNA REQUIREMENT ........................................................................................ 7-1 8. RADIO FRREQUENCY EXPOSURE COMPLIANCE.............................................. 8-1 9. DEVIATION TO TEST SPECIFICATIONS................................................................ 9-1 10. PHOTOGRAPH OF TEST ........................................................................................... 10-1 10.1. Photos of Power Line Conducted Emission Test ............................................................... 10-1 10.2. Photos of Radiated Emission Test...................................................................................... 10-1 11. PHOTOGRAPH OF EUT ............................................................................................. 11-1 R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:P9M-LASORX page Audix Technology (Shenzhen) Co…

Text truncated - open the document above for the full version.

R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:P9M-LASORX page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F15158 10-1 10. PHOTOGRAPH OF TEST 10.1.Photos of Power Line Conducted Emission Test R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:P9M-LASORX page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F15158 10-1 10.2. Photos of Radiated Emission Test (At Anechoic 3m Chamber Test 30-1000MHz) R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:P9M-LASORX page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F15158 10-2 (At Anechoic 3m Chamber Test 1GHz –25GHz)