PBKMS010114Combined Finger Print and Smart Card Reader

Precise 200 Series Quick Reference Using the Precise 200 series reader General Information The Precise 200 series readers - Precise 200 MC and Precise 250 MC - require the Precise 200 Series Drivers to be installed on the computer to work. See the “Installation of the Precise 200 series reader” section for more information about installation. Correct finger placement Correct and consistent finger placement is crucial for success. • Try to capture the center of the fingerprint ο Position the cuticle level with the center of the sensor ο Touch the small nubs above the sensor (when available) • Avoid rotating the finger • Place the finger flat to the sensor • Press with medium pressure Enhancing the fingerprint image quality If your finger is very dry • Try to press more firmly • Moisten your finger by breathing on it If your finger is very damp • Try to press less firmly • Wipe your finger dry More tips • Try placing your finger the way you did during enrollment • Keep the sensor surface clean ο If necessary, use a cotton cloth to clean the surface ο Do not use paper tissues for cleaning, they may scratch the surface • If your fingerprint is still not recognized, please consider re-enrollment to get a better matching template Installation of the Precise 200 series reader General information The Precise 200 series readers require the Precise 200 Series Drivers to be installed on the computer to work. The Precise 200 Series Drivers package is available for free downloading from Precise Biometrics’ Web site, www.precisebiometrics.com/downloads. The Precise 200 Series Drivers are also downloadable for Windows® Update, http://windowsupdate.microsoft.com, or may also be bundled with an application that uses the Precise 200 series reader. System Requirements • Windows® XP, Windows® 2000, Windows® 2003 • Minimum 300 MHz Pentium processor. • USB port Installation of a Precise 200 MC or Precise 250 MC reader 1. Install the Precise 200 Series Drivers. Run the setup file in the Precise 200 Series Drivers package or follow installation instructions in the application that bundles the Precise 200 Series Drivers. 2. Connect the reader Connect the Precise 200 MC or Precise 250 MC reader to the USB port on the computer and the reader will now work. Sweden USA Precise Biometrics AB Precise Biometrics Inc. Scheelevägen 19 C, SE-223 70 Lund 8300 Boone Boulevard, Suite 500, Vienna, VA 22182 Phone: +46 46 311 100, Fax +46 46 311 101 Phone: +1 (703) 848 9266, Fax +1 (703) 832 0577 Support: [email protected] Support: [email protected] Info: [email protected] Info: [email protected] Maintaining the Precise 200 series reader • Protect the Precise 200 series reader from any kind of physical damage. • Ensure that you are electrostatic discharged before putting the finger on the sensor. High electrostatic discharges might damage the fingerprint sensor. • Keep the sensor surface clean or there is an increased risk that the fingerprint can’t be successfully matched. • If necessary, clean the surface with a clean cotton cloth. You can dampen the cloth slightly with a cleaner. • Do not use paper tissues for cleaning purposes, because they may scratch the surface. • Do not spray cleaner directly onto the fingerprint reader. • Do NOT use chlorine-based cleaners, non-chlorine bleach, or chlorine-based bathroom or mildew cleaners. • Do NOT use any solvents, such as acetone, paint thinners, turpentine etc. Product Warranty information Please be informed that this Precise 200 series reader is covered by a limited product warranty pursuant to which this Precise 200 series reader will be free from defects in design, materials and workmanship for a period of twelve (12) months from the time of delivery from Precise Biometrics to the Precise Biometrics partner from which you purchased this Precise 200 series reader (the “Partner”). In case of a defect covered by the warranty, the defective unit shall be returned to the Partner, who will procure that the defective unit is repaired or replaced. THE ABOVE PARAGRAPH IS AN EXTRACT OF THE STANDARD PRECISE BIOMETRICS LIMITED PRODUCT WARRANTY, AND SHALL NOT BE CONSIDERED OR CONSTRUED AS AN INDEPENDENT WARRANTY STATEMENT. FOR THE COMPLETE WARRANTY CONDITIONS, WARRANTY LIMITATIONS, CUSTOMER RESPONSIBILITIES AND OTHER TERMS AND CONDITIONS, PLEASE CONTACT THE PARTNER. Electromagnetic compatibility (EMC) Notices Electromagnetic compatibility (EMC) is the ability of electronic equipment to function properly together in the electronic environment. CE Notice (Europe) The Precise 200 series readers, Precise 200 MC and Precise 250 MC meet the following technical standards: • EN 55022:1994 Limit B (Radiated emission) • EN 55024:1998 (Immunity of IT-equipment) FCC Information (USA) The Precise 200 MC and Precise 250 MC devices have been certified to the Class B digital device requirements as specified in the FCC rules and regulations (CFR47 Part 15 Subpart B). The Precise 200 MC and Precise 250 MC devices complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is e…

Text truncated - open the document above for the full version.

Document No ICON/LET/0002/PB Author Per Ola Olsson Date 2005-06-15 Revision F Page 1/1 Precise Biometrics AB Address: Phone: Fax: E-mail: Org. no.: Bankgiro Ideon Delta 3 +46 46 31 11 00 +46 46 31 11 01 [email protected] 556545-6596 5198-1686 Scheelev. 19C SE-223 70 Lund, Sweden PROJECT ICON TITLE Request for Confidentiality, FCC Name Function Date Checked: Approved: Authorised: 2005-06-15 Paper copies of this document are for reference only. The electronic original is authorised and archived according to GEN/MEM/0003/PB. Document No: ICON/LET/0002/PB Date: 2005-06-15 Revision: F Page: 2/2 The ownership and copyright of this document belongs to Precise Biometrics AB and must not be disclosed, copied, altered or used without the written permission of Precise Biometrics AB. Request for Confidentiality Tuesday, 15 June 2005 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 RE: Certification Application FCC ID: PBKMS010114 Please classify the following as confidential under the provision of 47 CFR 0.459: • The document “Block diagram & Product description for FCC and Schematics” The application contains technical information, which Precise Biometrics AB deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter. Per Ola Olsson Staff Engineer, hardware development Precise Biometrics AB Scheelevägen 19C SE-223 70 Lund Sweden Phone: +46 (0)46 31 11 06 Cellular: +46 (0)730 35 67 06 Fax: +46 (0)46 31 11 01 E-mail: [email protected]

Document No 51-RL010103 Author Harald Ripa Date 2005-06-02 Revision B Page 1/4 Precise Biometrics AB Address: Phone: Fax: E-mail: Org. no.: Bankgiro Ideon , Scheelev. 19 C, +46 46 286 57 60 +46 46 286 57 62 [email protected] 556545-6596 5198-1686 SE-223 70 Lund, Sweden +46 708 97 64 00 PRECISE 250 MC TYPE AND CERTIFICATION LABEL SPECIFICATION 1. SIZE The label size is 70 x 48 mm. 2. LABEL MATERIAL Silver polyester. The label must comply with UL 969 - Standard of Marking and Labelling Systems. 3. PRINT COLOUR The colour of all printing is black. 4. PRODUCT NUMBER AND REVISION The Product Number and Revision field shall read: MSXXXXXX YYY where XXXXXX is the product number of the Reader and YYY is the revision of the Reader. 5. SERIAL NUMBER The number series must continue from the latest number used in the production of the earlier revision. The printed serial number must be the same as the serial number stored in the scanner. Each number may only be used once, i.e. each produced scanner unit with identical Product Number must have a unique serial number. The serial number shall be preceded by the text “S/N:”. 6. PRODUCT NAME The name of the product shall be printed on the label. Example of a product name is “Precise 250 MC”. 7. PRODUCTION DATE The production date must be printed in one of the two following formats: YYwWW Document No: 51-RL010103 Date: 2005-06-02 Revision: B Page: 2/4 The ownership and copyright of this document belongs to Precise Biometrics AB and must not be disclosed, copied, altered or used without the written permission of Precise Biometrics AB. Where YY is two digits denoting year and WW is two digits denoting week. For instance, a unit produced week 23 year 2005 would be printed as “05w23”. OR YYmMM Where YY is two digits denoting year and MM is two digits denoting month. For instance, a unit produced in February year 2005 would be printed as “05m02”. Manufacturer in Sweden must use the YYwWW format. Manufacturer in USA must use YYmMM format. 8. UL-Mark The variant of cUL Listed mark where LISTED is placed to the right of the UL-Mark shall be used, see Figure 1 below. The size of the mark must be such that the ® in the UL-Mark is readable. Figure 1. UL-Mark for Listed products Below the UL-mark the text “INFO. TECH. EQUIP.” and the file UL-number E212590 shall be printed. See Figure 2 below. All text should be centred below the cUL Listed mark. INFO. TECH. EQUIP . E 2 12590 Figure 2. cUL-Mark with text 9. FCC 9.1. FCC ID The FCC id must be printed in capital letters. The FCC id must read: FCC ID: PBKMS010114 There must be a border surrounding the FCC ID text. Document No: 51-RL010103 Date: 2005-06-02 Revision: B Page: 3/4 The ownership and copyright of this document belongs to Precise Biometrics AB and must not be disclosed, copied, altered or used without the written permission of Precise Biometrics AB. 9.2. FCC 15.19 2-part statement The following statement must be printed on the label: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 10. WEEE The WEEE logo must be printed on the label. Figure 3. WEEE logo Document No: 51-RL010103 Date: 2005-06-02 Revision: B Page: 4/4 The ownership and copyright of this document belongs to Precise Biometrics AB and must not be disclosed, copied, altered or used without the written permission of Precise Biometrics AB. 11. LAYOUT The different fields on the label are specified in Figure 3 below (field contents are examples only). 2 4 5 1 3 Made in Sweden S/N: 12345678MS010114 YYY INFO. TECH. EQUIP. E212590 03w02 FCC ID: PBKMS010114 7 6 Precise 250 MC 8 9 10 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 11 Figure 3 - Type and certification label layout Field Type Description 1 Text Product name. Font: 10pt Arial. Bold. See par. 6 above. 2 Bitmap CE Logo. 3 Text “FCC ID: PBKMS010114” with frame. Font: 8pt Arial. See par. 9.1 above. 4 Text + Bitmap c-UL Listed logo and the text “INFO. TECH. EQUIP. E212590. Font: 6pt Arial. Bold. See par. 8 above. 5 Barcode Product number, Revision and Serial number coded in Code128, subset A. 6 Text Product number & revision. Font: 6pt Arial. See par. 4 above. 7 Text “Made in Sweden” Font: 6pt Arial. 8 Bitmap WEEE Logo. 9 Text Serial number, 8 digits. Font: 6pt Arial. See par. 5 above. 10 Text Production date. Font: 6pt Arial. See par. 7 above. 11 Text FCC statement. Font Arial Narrow 6pt. See par 9.2

1 Page: 1of 5 TEST REF. NO: 05/2097 DATE: June 6, 2005 TEST REPORT REPORT CERTIFICATE issued by a FCC listed Test Laboratory CUSTOMER AND Project no: 05255 MANUFACTURER: Precise Biometrics AB Scheelevägen 19 C SE-223 70 Lund Sweden EQUIPMENT UNDER TEST (EUT): Combined Fingerprint and Smart Card Reader, Type Precise 250MC, p/n MS 010114-P1C, without s/n. TEST SPEC: 47 Cfr Ch. 1 (10-1-04 Edition): Part 15, Subpart B, Class B. §15.107: Conducted Emission, AC power line §15.109: Radiated Emission DATE OF TEST: June 1 - 7, 2005 TEST SITE: Svenska EMC Lab AB, Karlskrona, Sweden. FCC registration number: 90967. CONFORMITY: The EUT (Equipment Under Test), did pass the above mentioned tests. The test result shows full compliance with the technical specification for Class B Digital Devices. -------------------------------------------------------------------------------------------------------------------- Approved, Karlskrona June 6, 2005 ................................................... Hans Östergren Manager Svenska EMC Lab AB This report may not be reproduced other than in full, except with the prior written approval of Svenska EMC Lab AB. 2 Page: 2 of 5 TEST REF. NO: 05/2097 DATE: June 6, 2005 ------------------------------------------------------------------------------------------------------------------------ DATE OF RECEIPT: June 1, 2005 CONDITION OF EUT: No remarks. Operates as intended. TEST PERSONNEL: Svenska EMC Lab AB: Bo Gidlöw. ASSISTANT PERSONNEL: Precise Biometrics AB: Per Ola Olsson. EUT DESCRIPTION: EUT is a combined fingerprint reader and smart card reader. Its primary use is logical access. EUT has only one fixed cable for connection to USB port. EUT is powered through the USB cable. CALIBRATION DECLARATION: The test equipment is calibrated with tractability to national or international standards. All instruments were within the calibration interval. Before starting the tests, the conducted emission test system and the radiated emission test system were checked with Generator CNE III as reference source. 3 Page: 3 of 5 TEST REF. NO: 05/2097 DATE: June 6, 2005 ------------------------------------------------------------------------------------------------------------------------ ESTIMATED UNCERTAINTY: Expanded uncertainty (k = 2): Conducted Emission, 0.45 – 30 MHz: ± 1.1 dB Field Strength, emission 30 – 300 MHz: ± 2.2 dB Field Strength, emission 300 – 700 MHz: ± 2.3 dB Field Strength, emission 700 – 2000 MHz: ± 2.4 dB Field Strength, emission 1 to 2 GHz: ± 3.0 dB Frequency: ± 100 Hz The uncertainties are for a confidence level of not less than 95 %. TEST EQUIPMENT LIST: Type/Manufacturer/Bandwidth s/n p/n Calibration information Date Interval EMI Test System, Monitor EZM, 860157/014 93-1110 2004-07 12 months Rohde & Schwarz EP-6, 20 Hz - 1300 MHz Test Receiver, Rohde & Schwarz ESH-3, 894979/013 93-1108 2004-07 12 months 9 kHz - 30 MHz Test Receiver, Rohde & Schwarz ESVP, 893497/006 93-1109 2004-07 12 months 20 - 1300 MHz Pulse Limiter, Rohde & Schwarz ESH3-Z2 357881052 93-1113 2004-07 12 months DC - 30 MHz Plotter, Rohde & Schwarz DOP 2 893117/0108 93-1112 NA NA Spectrum Analyzer Tektronix 2755AP, B010111 93-1106 2004-07 12 months 10 kHz - 21 GHz Preamplifier, Mini-Circuits ZHL-42, - 860701 2005-02 12 months 0.7 – 4.2 GHz LISN 50 OHM/50 μH, Electro Metrics EM-7820 2771 95-1247 2004-07 12 months 10 kHz - 30 MHz, 16 A Cable to Test Receiver, RG 223 006 93-1222 2004-08 12 months Cable to LISN, RG 223 015 93-1231 2004-08 12 months Biconical Antenna, Schwarzbeck BBA9106 - 93-92196.1 2004-07 24 months 30 - 300 MHz Log-periodic Antenna, Schwarzbeck 91071205 93-92196 2004-07 24 months UHALP9107, 300 - 1000 MHz Double Ridged Guide Antenna, EMCO 3115, 2338 93-85122 2003-07 36 months 1 - 18 GHz Antenna Cable, RG 214 001 93-1217 2004-08 12 months Antenna Cable, Sucoflex 104 171288/4 93-1239 2004-08 12 months Antenna Mast System, Jyske EMC, h = 1 - 4 m 02 93-90172 NA NA Turn Table, Jyske EMC, h = 1 m 01 93-90171 NA NA Anechoic Chamber, 8 x 4.5 x 3 m 1 93-87151 2003-04 36 months Open Area Test Site for 3 m antenna distance 1 93-1108 2003-12 36 months 4 Page: 4 of 5 TEST REF. NO: 05/2097 DATE: June 6, 2005 ------------------------------------------------------------------------------------------------------------------------ TEST SET-UP AND PROCEDURE: As laid out in ANSI C.63.4:2001 Document. Tested as tabletop equipment. See Appendix 1 and 2. TEST CONDITIONS: Rating: - PC: 115 VAC, 50-60 Hz, 0.7 A. Class I. - EUT: 5 VDC, 0.5 A. Clock Frequency: 7.38 MHz, 12.0 MHz, 192.0 MHz. Measured frequency range: 0.15 – 2 000 MHz. Configuration: See Appendix 3. A minimum system was configured with a PC and its peripherals. EUT was connected to the USB port, other devices to the serial and parallel ports (15.31(i)). The system consists of: - PC, IBM Thinkpad 600E, Type 2645-4BG, s/n 5528TVC02/99, FCC ID: Tested to comply with FCC regulations. - AC/DC Adapter, IBM IZORV 860 PF, Type OZK6543, s/n 2M04T7782PF, FCC ID: Tested to comply with FCC regulations. - Printer, HP Deskjet 895cxi, Type C6410A, s/n HU0151N087, FCC ID: Tested to comply with FCC regulations. - AC/DC Adapter to Printer, Type C6409-60014, s/n T5844428252, FCC ID: Tested to comply with FCC regulations. - Mouse, Microsoft Wheelhouse, Type X05-51692, s/n 0304842-00000, FCC ID: Tested to comply with FCC regulations. Cables: - Unshielded mains cable of 1.8 m length with safety ground to the AC/DC Adapter (PC). - Shielded DC cable of 1.8 m length without safety ground from AC/DC Adapter to PC. - Shielded USB (signal and power) cable of 2 m length from EUT 250MC to the PC (USB port). - Shielded Printer cable of 1.8 m length from PC to Printer (parallel port). - Unshielded mains cable of 1.8 m length without safety ground to the AC/DC Adapter (Printer). - Shielded DC cable of 2 m length without safety ground from AC/DC Adapter to Printer. - Shielded Mouse cable of 1.8 m length from PC to external Mouse (serial port). See also Appendix 3. Operating…

Text truncated - open the document above for the full version.

Precise Biometrics ABDATE: April 29, 2005 Combined Fingerprint and Smart Card Reader, Type Precise 250MC Precise Biometrics ABDATE: April 29, 2005 Combined Fingerprint and Smart Card Reader, Type Precise 250MC