PBLWL541CCardBus 11g Wireless Network Adapter

CardBus 11G WIRELESS Network Adapter User’s Manual - i - Production component This WIRELESS production should contain the following items: 1. One piece of CardBus 11G WIRELESS LAN Card 2. One piece of CD which contain drivers, user’s manual, and utility Quick Installation 1. Insert the product’s CD into CD-ROM. 2. Exit all application programs and insert the 11G WIRELESS adapter into the PCMCIA slot. 3. Following “Found New Hardware Wizard” window to install driver step by step. 4. Install the WIRELESS adapter utility 5. Configure your WIRELESS adapter for connecting to a WIRELESS network. FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2. this device must accept any interference received; including interference that may cause undesired operation. Federal Communications Commission (FCC) Statement. This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This device has been tested for compliance with FCC RF Exposure (SAR) limits in a typical laptop configuration with a PCMCIA slot on either the right or left side of the laptop. In order to comply with the FCC SAR limits, it is recommended when using a PC card adapter that the integrated antenna is positioned more than 1.5 centimeters from nearby persons during extended periods of operation. If the antenna is positioned less than 1.5 centimeters from nearby persons, it is recommended that the user limit exposure time." - iii - Contents CHAPTER 1 TERMINOLOGY INTRODUCTION 1 CHAPTER 2 SYSTEM REQUIREMENTS 3 2-1 HARDWARE 3 2-2 SOFTWARE 3 CHAPTER 3 INSTALL DRIVER FOR WINDOWS SERIES 4 3-1 SET UP WIRELESS LAN CARD FOR WINDOWS XP 4 3-2 SET UP WIRELESS LAN CARD FOR WINDOWS 2000 7 3-3 SET UP WIRELESS LAN CARD FOR WINDOWS 98/ ME 11 3-4 UNINSTALL THE WIRELESS LAN CARD 14 CHAPTER 4 CONFIGURE THE WIRELESS LAN ADAPTER 17 4-1 INSTALL UTILITY 17 4-2 CONFIGURE WIRELESS LAN ADAPTER FOR WINDOWS XP 18 4-3 CONFIGURE WIRELESS LAN ADAPTER FOR WINDOWS 98/ME/2000 BY UTILITY 21 - 1 - Chapter 1 Terminology Introduction This chapter will introduce terminology about IEEE802.11 what referred by this manual. And in this character we will explain terminology according to IEEE802.11 Std. z Ad-Hoc Network(Peer to Peer) A network composed solely of stations within mutual communication range of each other via the WIRELESS medium(WM). An Ad Hoc network is typically created in a spontaneous manner. The principal distinguishing characteristic of an ad hoc network is limited temporal and spatial extent. These limitations allow the act of creating and dissolving the ad hoc network to be sufficiently straightforward and convenient so as to be achievable by nontechnical users of the network facilities; i.e., no specialized “technical skills” are required and little or no investment of time or additional resources is required beyond the stations that are to participate in the ad hoc network. The term ad hoc is often used as slang to refer to an independent basic service set(IBSS). z Infrastructure Network The infrastructure includes the distribution system medium (DSM), access point(AP), and portal entities. It is also the logical location of distribution and integration service functions of an extended service set(ESS). An infrastructure contains one or more APs and zero or more portals in addition to the distribution system(DS). z Basic Service Set(BSS) A set of stations controlled by a single coordination function. z BSSID Basic service set identifier z Station service(SS) The set of services that support transport of medium access control(MAC) service data units(MSDUs) between stations within a basic service set(BSS) z SSID Station service identifier - 2 - z Association The service used to establish access point/station(AP/STA) mapping and enable STA invocation of the distribution system services(DSSs). z Authentication The service used to establish the identify of one station as a member of the set of stations authorized to associate with another station. z Channel an instance of medium use for the purpose of passing protocol data units(PDUs) that may be used simultaneously, in the same volume of space, with other instances of medium use(no other channels) by other instances of the same physical layer(PHY), with an acceptably low frame error ratio due to mutual interference. Some PHYs provide only one channel, whereas others provide multiple channels. Examples of channel types are shown in the following tables Single channel n-channel Narrowband radio-frequency(RF) channel Frequency division multiplexed channels Baseband infrared Direct sequence spread spectrum(DSSS) with code division multiple access z Wired equivalent privacy(WEP) The optional cryptographic confidentiality algorithm specified by IEEE 802.11 …

Text truncated - open the document above for the full version.

Company : Advance Multimedia Internet Technology Inc. Page : 1 of 4 Product : CardBus 11g Wireless Network Adapter Model : WL541C Company : Advance Multimedia Internet Technology Inc. Page : 2 of 4 Product : CardBus 11g Wireless Network Adapter Model : WL541C Company : Advance Multimedia Internet Technology Inc. Page : 3 of 4 Product : CardBus 11g Wireless Network Adapter Model : WL541C Company : Advance Multimedia Internet Technology Inc. Page : 4 of 4 Product : CardBus 11g Wireless Network Adapter Model : WL541C

Company: Advance Multimedia Internet Technology Inc. Model: WL541C Product : CardBus 11g Wireless Network Adapter CardBus 11g Wireless Network Adapter Model No: WL541C FCC IDPBLWL541C This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: [1] this device may not cause harmful interference and [2] this device must accept any interference received, including interference that may cause undesired operation. S/N Made in Taiwan

Company : Advance Multimedia Internet Technology Inc. Page : 1 of 4 Product : CardBus 11g Wireless Network Adapter Model : WL541C Company : Advance Multimedia Internet Technology Inc. Page : 2 of 4 Product : CardBus 11g Wireless Network Adapter Model : WL541C Company : Advance Multimedia Internet Technology Inc. Page : 3 of 4 Product : CardBus 11g Wireless Network Adapter Model : WL541C Company : Advance Multimedia Internet Technology Inc. Page : 4 of 4 Product : CardBus 11g Wireless Network Adapter Model : WL541C

Description of Operation EUT is a CardBus 11g Wireless Network Adapter with 11 channels. This device provided four kind of transmitting speed 1,2,5.5 and 11Mbps. The device of RF carrier is DQPSK,DB PSK and CCK. The device adapts direct sequence spread spectrum modulation. The Connector antenna was scolded on PCB provided diversity function to improve the receiving function. This CardBus 11g Wireless Network Adapter is an IEEE 802.11b Wireless LAN adapter. It allows your computer to connect to a wireless network and to share resources, such as files or printers without being bound to the network wires. Operation in 2.4GHz Orthogonal Frequency Division Multiplex (O.F.D.M) or Direct Sequence Spread Spectrum (D.S.S.S) radio transmission, the CardBus 11g Wireless Network Adapter transfers data at speeds up to 64/128-bit Wired Equivalent Protection(WEP) algorithm is used. In addition, its standard compliance ensures that it can communicate with any 802.11g/b network.

Report No. : ER/2003/90009 Page : 1 of 35 TEST REPORT Equipment Under Test : CardBus 11g Wireless Network Adapter Model No. : WL541C FCC ID : PBLWL541C Applicant Advance Multimedia Internet Technology Inc. No.32, Hwan-Gong Rd. Yung Kang City, Tainan Hsien, Address of Applicant : Ta i w a n . Date of Receipt : 2003.09.16 Date of Test(s) : 2003.09.17 – 2003.09.19 Date of Issue : 2003.09.22 Standards: FCC OET Bulletin 65 supplement C, ANSI/IEEE C95.1 , C95.3 In the configuration tested, the EUT complied with the standards specified above. Remarks: This report details the results of the testing carried out on one sample, the results contained in this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS Taiwan E&E Services or testing done by SGS Taiwan E&E Services in connection with distribution or use of the product described in this report must be approved by SGS Taiwan E&E Services in writing. Tested by : Dikin Yang Date : 2003.09.17 Approved by : Robert Chang Date : 2003.09.22 Report No. : ER/2003/90009 Page : 2 of 35 Contents 1. General Information 1.1 Testing Laboratory 3 1.2 Details of Applicant 3 1.3 Description of EUT(s) 3 1.4 Test Environment 3 1.5 Operation Configuration 4 1.6 The SAR Measurement System 4 1.7 SAR System Verification 4 1.8 Tissue Simulant Fluid for the Frequency Band 2.4 to 2.5 GHz 5 1.9 Operation Procedure 5 1.10 Test Standards and Limits 6 2. Instruments List 8 3. Summary of Results 9 4. Measurements 10 802.11b 4.1.1 Edge-on position, lowest channel 10 4.1.2 Edge-on position, middle channel 11 4.1.3 Edge-on position, highest channel 12 4.1.4 End-on position, lowest channel 13 4.1.5 End-on position, middle channel 14 4.1.6 End-on position, highest channel 15 802.11g 4.2.1 Edge-on position, lowest channel 16 4.2.2 Edge-on position, middle channel 17 4.2.3 Edge-on position, highest channel 18 4.2.4 End-on position, lowest channel 19 4.2.5 End-on position, middle channel 20 4.2.6 End-on position, highest channel 21 4.3.1 System Performance Validation 22 APPENDIX 1. Photographs of Test Setup 23 2. Photographs of EUT 27 3. Probe Calibration certificate 29 4. Uncertainty Analysis 33 5. Phantom description 34 6. System Validation from Original equipment supplier 35 Report No. : ER/2003/90009 Page : 3 of 35 1. General Information 1.1 Testing Laboratory SGS Taiwan Ltd. ( FCC Registration number: 573967 ) 1F, No. 134, Wukung Road, Wuku industrial zone Taipei county , Taiwan , R.O.C. Telephone : +886-2-2299-3279 Fax : +886-2-2298-2698 Internet : http://www.sgs.com.tw 1.2 Details of Applicant Applicant : Advance Multimedia Internet Technology Inc. Address : No.32, Hwan-Gong Rd. Yung Kang City, Tainan Hsien, Ta i w a n . 1.3 Description of EUT(s) 1 Product name CardBus 11g Wireless Network Adapter 2 Model Number WL541C 3 Antenna Type Integra 4 Power supply Powered by PCMCIA slot 3.3V/5V 5 Frequency range 2412-2462 MHz 1.4 Test Environment Ambient temperature : 21.9° C Tissue Simulating Liquid : 21° C- 23° C Report No. : ER/2003/90009 Page : 4 of 35 1.5 Operation Configuration Configuration 1: “ Edge-on” placement; edge of the PC at 90° and at a distance of 1.5 cm from the base of the phantom (Fig.3 & Fig.4 & Fig.5) Configuration 2: “End-on” placement; Bottom of the Pc is paralleled and at a distance of 0.0 cm from the base of the phantom, but 1.1 cm Spacing between EUT & Planar Phantom. (Fig.6 & Fig.7 & Fig.8) 1.6 The SAR Measurement System A photograph of the SAR measurement System is given in Fig. 2. This SAR Measurement System uses a Computer-controlled 3-D stepper motor system ( Speag Dasy 4 professional system ). A Model ET3DV6 1759 E-field probe is used to determine the internal electric fields. The SAR can be obtained from the equation SAR= σ (|Ei| 2 )/ ρ where σ and ρ are the conductivity and mass density of the tissue-simulant. 1.7 SAR System Verification The microwave circuit arrangement for system verification is sketched in Fig.1. The Measured SAR distribution for the peak 1-g SAR is 13.7 m W/g and 10-g SAR is 6.16 m W/g. The measured 1-g SAR is 13.2 m W/g and 10-g SAR is 5.82 m W/g for this dipole. In comparison, it shows that the measured SAR plot is quite close to the original one.(see APPENDIX 6 System Validation from Original equipment supplier SPEAG by Schmid & Partner) D C F A B E Fig.1 The microwave circuit arrangement used for SAR system verification A. Agilent Model 8648D Signal Generator B. Mini circuits Model ZHL-42 Amplifier C. Agilent Model E4416A Power Meter D. Agilent Model 8482H Power Sensor E. Agilent Model 777D Dual directional coupling F. Reference dipole antenna Report No. : ER/2003/90009 Page : 5 of 35 Validation Kit Frequency Target SAR 1g (250mW) Ta r g e t SAR 10g (250mW) Measured SAR 1g Measured SAR 10g Measured date DT3DV6 S/N :1759 2450 MHz 13.7 m W/g 6.16 m W/g13.2 m W/g5.82 m W/g 2003-09-10 Table 1. Results system validation 1.8 Tissue Simulant Fluid for the Frequency Band 2.4 to 2.5 GHz The dielectric properties for this body-simulant fluid were measured by using the HP Model 85070D Dielectric Probe (rates frequence band 200 MHz to 20 GHz) in conjuncation with HP 8714ET Network Analyzer(300 KHz-3000 MHz ) by using a procedure detailed in Section V. The Measured dielectric parameters of the body-simulant fluid at 2400 MHz are ρ =52.5± 5%, σ =2.00±10% S/m. The measured properties are close to the values of ρ =51.66 and σ =2.021 S/m. The Conductivity (σ) and Permittivity (ρ) are listed in Table 1.For the SAR measurement given in this report . We obtain the desired dielectric properties to simulate the body tissue at the midband frequency…

Text truncated - open the document above for the full version.

Ecom Sertech Corp. Rm. 258, Bldg. 17, NO.195, Sec. 4 Chung Hsing Rd.,Chu -Tung Chen, Hsinchu, Taiwan 310, R.O.C TEL:886 - 3 - 5918012 FAX : 886 - 3 - 5825720 FCC ID ：PBLWL541C Report No.：ER03-09-028FRF Page 1 of 59 TEST REPORT Product Name ： CardBus 11g Wireless Network Adapter Model Number ： WL541C Applicant ： Advance Multimedia Internet Technology Inc. Address ： NO.32, Hwan-Gong Rd. Yung Kang City, Tainan Hsien, Taiwan. Received Date ： Sept. 04, 2003 Tested Date ： Sept. 04~Sept. 25, 2003 Notes ： 1. This report will be invalid if duplicated or photocopied in part. 2. This report refers only to the specimen(s) submitted to testing, and be invalid as seperately used. 3. This report is invalid without examination stamp and signature of this institute. 4. The tested specimen(s) will be preserved for thirty days from the data issued. 5. The report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. Ecom Sertech Corp. Rm. 258, Bldg. 17, NO.195, Sec. 4 Chung Hsing Rd.,Chu -Tung Chen, Hsinchu, Taiwan 310, R.O.C TEL:886 - 3 - 5918012 FAX : 886 - 3 - 5825720 FCC ID ：PBLWL541C Report No.：ER03-09-028FRF Page 2 of 59 Test Report Certification Product Name : CardBus 11g Wireless Network Adapter Model Number : WL541C Applicant : Advance Multimedia Internet Technology Inc. Measurement Standard : 47 CFR Part 15, Subpart B and Subpart C (Section 15.247), ANSI C63.4-2001 WE HEREBY CERTIFY THAT: The measurements shown in the attachment were made in accordance with the procedures indicated, and the energy emitted by the equipment was found to be within the limits applicable. We assume full responsibility for the accuracy and completeness of these measurements and vouch for the qualifications of all persons taking them. Ecom Sertech Corp. Rm. 258, Bldg. 17, NO.195, Sec. 4 Chung Hsing Rd.,Chu -Tung Chen, Hsinchu, Taiwan 310, R.O.C TEL:886 - 3 - 5918012 FAX : 886 - 3 - 5825720 FCC ID ：PBLWL541C Report No.：ER03-09-028FRF Page 3 of 59 TABLE OF CONTENTS TITLE PAGE NO. 1. GENERAL INFORMATION ....................................................................................................................5 1.1 General Statement ....................................................................................................................................5 1.2 General Description of EUT & Power .....................................................................................................5 1.3 Description of Peripherals ........................................................................................................................6 1.4 EUT & Peripherals Setup Diagram ..........................................................................................................7 1.5 EUT Operating Condition ........................................................................................................................7 1.6 Description of Test Site ............................................................................................................................8 1.7 Summary of Test Results..........................................................................................................................8 2. CONDUCTED POWERLINE TEST .........................................................................................................9 2.1 Test Equipments .......................................................................................................................................9 2.2 Test Setup .................................................................................................................................................9 2.3 Conducted Power Line Emission Limit....................................................................................................10 2.4 Test Procedure ..........................................................................................................................................10 2.5 Uncertainty of Conducted Emission.........................................................................................................10 2.6 Conducted RF Voltage Measurement.......................................................................................................11 2.7 Photos of Conduction Test .......................................................................................................................12 3. RADIATED EMISSION TEST .................................................................................................................13 3.1 Test Equipments .......................................................................................................................................13 3.2 Test Setup .................................................................................................................................................13 3.3 Radiation Limit.........................................................................................................................................14 3.4 Test Procedures ........................................................................................................................................15 3.5 Uncertainty of Radiated Emission ............................................................................................................15 3.6 Radiated RF Noise Measurement .............................................................................................................16-41 3.7 Photos of Open Site ..................................................................................................................................42-43 4. 6dB BANDWIDTH MEASUREMENT ....................................................................................................44 4.1 Test Equipments .......................................................................................................................................44 4.2 Test Setup ..............…

Text truncated - open the document above for the full version.

Ecom Sertech Corp. Rm. 258, Bldg. 17, NO.195, Sec. 4 Chung Hsing Rd.,Chu -Tung Chen, Hsinchu, Taiwan 310, R.O.C TEL:886 - 3 - 5918012 FAX : 886 - 3 - 5825720 FCC ID ：PBLWL541C Report No.：ER03-09-028FRF Page 12 of 59 2.7 Photos of Conduction Test Ecom Sertech Corp. Rm. 258, Bldg. 17, NO.195, Sec. 4 Chung Hsing Rd.,Chu -Tung Chen, Hsinchu, Taiwan 310, R.O.C TEL:886 - 3 - 5918012 FAX : 886 - 3 - 5825720 FCC ID ：PBLWL541C Report No.：ER03-09-028FRF Page 42 of 59 3.7 Photos of Open Site Ecom Sertech Corp. Rm. 258, Bldg. 17, NO.195, Sec. 4 Chung Hsing Rd.,Chu -Tung Chen, Hsinchu, Taiwan 310, R.O.C TEL:886 - 3 - 5918012 FAX : 886 - 3 - 5825720 FCC ID ：PBLWL541C Report No.：ER03-09-028FRF Page 43 of 59