PCU-JLDK-18Wireless remote handset

OKIN Refined Electric Technology Co., Ltd Page 1 of 4 Operating Manual of Remote Hand Control Connect diagram please see the drawing：”System Diagram-Scape Bed Controls” “System Diagram-Scape Bed Controls” 1、Interface of the Handset 2、Button description A. Reading/TV Position button：Press the button and the head motor will move up to the highest and stop, at the same time, the foot motor will touch bottom and stop. You can press any button to stop action during moving. OKIN Refined Electric Technology Co.,Ltd Page 2 of 4 B. HEAD button：Press and hold the button, the head motor will go up or down. C. FEET button：Press and hold the button, the foot motor will go up or down. D. Z-G button: Press the button, the head and foot motor will move simultaneously and do not stop until return to the position of the system set. You can press any button to stop action during moving. Optional：The Z-G button can be set as a memory button by user. See point 4. E. FLAT button：Press the button, the head and foot motor will move down to the flat position simultaneously. You can press any button to stop action during moving. F. HEAD Massage button：Press the button + or -，you can open the head vibrator and control the vibrating range（+Stronger, -Weaker）. The vibrating range is divided into 3 levels and the default vibrating time is 10min. G. FEET Massage button：Press the button, you can open the foot vibrator and control the vibrating intensity (+Stronger, -Weaker). The vibrating intensity is divided into 3 levels and the default vibrating time is 10min. H． STOP button：Press the button, you can stop the head and foot vibrator and the massage system will close. Note：The vibrating intensity of the head vibrator is a little stronger than the foot vibrator. 3、Wireless Matching operation Before use the whole system, user need match the handset with control box. Step 1: Connect the whole system according to “System Diagram-Scape Bed Controls” Step 2: Power off the system, plug off the mains cable with power socket; Step 3: Take out the dry batteries of handset, set up DIP switch to a desired channel. Then install the batteries; Step 4: Power on the control box; OKIN Refined Electric Technology Co.,Ltd Page 3 of 4 Step 5: Press and hold up button and up button until backlight LED flashing. Loose the two buttons and LED continue flashing and search with control box, once LED stop flashing the matching is successful, which means the control box and the handset can work together. All matching set up process must finish in 30sec after power on control box. Notes：USB cable only use for synchronized operation of two beds. 4、Memory operation： Z-G button can be set as a memory button by user. Step 1: Adjust the head position and feet position until your like position; Step 2: Press and hold the button for 1sec, backlight LED start flashing; Step 3: loose button, during next 1sec, press button, LED stop flashing. Then memory operation is successful. FCC STATEMENT: FCC ID:PCU-JLDK.18 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. OKIN Refined Electric Technology Co.,Ltd Page 4 of 4 However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (current) 2.0 3.0 Jan-31-2012 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 3.0 OKIN Refined Electric Technology Co., Ltd. August 22, 2012 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, OKIN Refined Electric Technology Co., Ltd. hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): FCC ID: PCU-JLDK-18 Wireless remote controller Model name: JLDK.18 We affirm that between SIEMIC and OKIN Refined Electric Technology Co., Ltd, any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Minglong Lei Title: General Manager OKIN Refined Electric Technology Co., Ltd. Address: Plant 4, No. 410, Xinyonglian Road, Wangjiangjing Development Zone, Jiaxing Zhejiang China Telephone: 0086-573-82281072 Fax : 0086-0573-82280968 E-mail: [email protected]

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 OKIN Refined Electric Technology Co., Ltd. August 22, 2012 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: PCU-JLDK-18 We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Schematics - Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Minglong Lei Title: General Manager OKIN Refined Electric Technology Co., Ltd. Address: Plant 4, No. 410, Xinyonglian Road, Wangjiangjing Development Zone, Jiaxing Zhejiang China Telephone: 0086-573-82281072 Fax : 0086-0573-82280968 E-mail: [email protected]

External photos

Internal photos

NINGBO EMTEK CO., LTD. REPORT NO: KAN120803005E FCC ID: PCU-JLDK-18 DATE: 08/28/2012 Page 1 of 23 ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART B &C REQUIREMENT OF Wireless remote handset MODEL No.: JLDK.18 FCC ID: PCU-JLDK-18 REPORT NO: KAN120803005E ISSUE DATE: August 28, 2012 Prepared for OKIN REFINED ELECTRIC TECHNOLOGY CO., LTD. Plant 4, No.410, Xinyonglian Road, Wangjiangjing Development Zone, Jiaxing Zhejiang China Prepared by NINGBO EMTEK CO., LTD 1F Building 4, 1177#, Lingyun Road, Ningbo National Hi-Tech Zone, Ningbo, Zhejiang, China TEL: 0086-574-27907998 FAX: 0086-574-27721538 NINGBO EMTEK CO., LTD. REPORT NO: KAN120803005E FCC ID: PCU-JLDK-18 DATE: 08/28/2012 Page 2 of 23 VERIFICATION OF COMPLIANCE Applicant: OKIN REFINED ELECTRIC TECHNOLOGY CO., LTD. Plant 4, No.410, Xinyonglian Road, Wangjiangjing Development Zone, Jiaxing Zhejiang China Product Description: Wireless remote handset Model Number: JLDK.18 File Number: KAN120803005E Date of Test: August 06, 2012 to August 27, 2012 We hereby certify that: The above equipment was tested by NINGBO EMTEK CO., LTD. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 (2009) and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.249. The test results of this report relate only to the tested sample identified in this report. Approved By Andy.wang/Manager NINGBO EMTEK CO., LTD. NINGBO EMTEK CO., LTD. REPORT NO: KAN120803005E FCC ID: PCU-JLDK-18 DATE: 08/28/2012 Page 3 of 23 Table of Contents 1. GENERAL INFORMATION........................................................................................................... 4 1.1. Product Description...................................................................................................................... 4 1.2. Related Submittal(s) / Grant (s) ................................................................................................... 4 1.3. Test Methodology ........................................................................................................................ 4 1.4. Special Accessories ...................................................................................................................... 4 1.5. Equipment Modifications............................................................................................................. 4 1.6. Test Facility.................................................................................................................................. 5 1.7. Measurement Uncertainty ............................................................................................................ 5 2. SYSTEM TEST CONFIGURATION ............................................................................................. 6 2.1. EUT Configuration ...................................................................................................................... 6 2.2. EUT Exercise ............................................................................................................................... 6 2.3. Requirement for Compliance ....................................................................................................... 6 2.4. Configuration of Tested System................................................................................................... 8 2.5. Description of support units ......................................................................................................... 8 3. SUMMARY OF TEST RESULTS ................................................................................................... 9 4. DESCRIPTION OF TEST MODES................................................................................................ 9 5. RADIATED EMISSION TEST ..................................................................................................... 10 5.1. Measurement Procedure............................................................................................................. 10 5.2. Measurement Equipment Used: ................................................................................................. 10 5.3. Test SET-UP............................................................................................................................... 10 5.4. Radiated Measurement Result ................................................................................................... 12 5.5. Radiated Measurement Photos:.................................................................................................. 18 6. BAND EDGES MEASUREMENT................................................................................................ 20 6.1. Standard Applicable ................................................................................................................... 20 6.2. Measurement Procedure............................................................................................................. 20 6.3. Measurement Equipment ...........................................................................................................20 6.4. Test Setup ................................................................................................................................... 20 6.5. Test Results ................................................................................................................................ 20 7. ANTENNA APPLICATION........................................................................................................... 23 7.1. Standard Applicable ................................................................................................................... 23 7.2. Antenna Construction .............................................................…

Text truncated - open the document above for the full version.

Setup photos Above 1000MHz: 30M~1000MHz: