PDC-ILM4X30GSInternet Location Manager

&LEET2ESOURCE-ANAGER)N 6EHICLE$EVICE -ORETIMEONTHEROAD š )NSTALLATION'UIDE &LEET2ESOURCE-ANAGER)N 6EHICLE$EVICE 6/)' *ANUARY  63  This page intentionally left blank. Product Safety Information Introduction Application Information ............................................................................................................................................. 1 Installation Tools ....................................................................................................................................................... 2 Space Claim VS-4500 Dimensions ................................................................................................................................................. 3 Mounting Requirements VS-4500 ..................................................................................................................................................................... 4 Typical Components Location ................................................................................................................................... 5 Electrical Requirements VS-4500 ..................................................................................................................................................................... 6 Power Requirements ......................................................................................................................................... 6 Wiring Schematic .............................................................................................................................................. 6 Wiring Harness ................................................................................................................................................. 7 Connector “A” .................................................................................................................................................... 8 Power and Ground ............................................................................................................................................ 9 J1587 ................................................................................................................................................................. 10 J1939 ................................................................................................................................................................ 11 OBDII ................................................................................................................................................................. 12 Spare I/O ............................................................................................................................................................ 13 VS-4500 B Connection ....................................................................................................................................... 14 Interconnection Table......................................................................................................................................... 15 Ethernet RJ45 .................................................................................................................................................... 16 Spare Outputs .................................................................................................................................................... 17 Internet Data Terminal........................................................................................................................................ 18 Satellite Antenna ................................................................................................................................................ 19 Safety Package .......................................................................................................................................................... 21 Side Sensor ....................................................................................................................................................... 21 VORAD Components ......................................................................................................................................... 21 Wireless Antenna Type and Location ........................................................................................................................................ 23 Option A (cellular) ...................................................................................................................................................... 24 Option B (combination GPS and cellular) ................................................................................................................... 25 Option E (glass mounted combination) ...................................................................................................................... 26 Option J (speciality antenna)...................................................................................................................................... 27 Option F (speciality antenna)...................................................................................................................................... 28 Option G (supports diversity) ..................................................................................................................................... 29 Option H (supports diversity) ..................................................................................................................................... 29 Satellite Antenna ........................................................................................................................................................ 30 Appendix Retrofit Information .................................................................................................................................................. 31 J1939/11 Data Link Detail .…

Text truncated - open the document above for the full version.

A Trimble Company April 11 th 2007 Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, @Road requests confidentiality for the following products: FCC ID Number Product Title/Model PDC– ILM4X30GS Internet Location Manager/iLM4530 For the product stated above, we request that the following information be held confidential: 1) Electrical Schematics of the Circuitry 2) Block Diagram 3) Bill of materials 4) Operational Descriptions 5) Tune up Procedure No other items submitted as part of the equipment authorization filing process are deemed confidential. The above exhibits contain @Road trade secrets and proprietary information that could be of benefit to our competitors regarding the design of our mobile device. This material is not customarily available to the general public and we request that it be withheld from public inspection. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name: Anil Tiwari Title: Vice President of Engineering 47071 Bayside Pkwy. Fremont, CA 94538 (510) 870-1264 A Trimble Company April 11 th 2007 Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, @Road requests confidentiality for the following products: FCC ID Number Product Title/Model PDC– ILM4X30GS Internet Location Manager/iLM4230 For the product stated above, we request that the following information be held confidential: 1) Electrical Schematics of the Circuitry 2) Block Diagram 3) Bill of materials 4) Operational Descriptions 5) Tune up Procedure No other items submitted as part of the equipment authorization filing process are deemed confidential. The above exhibits contain @Road trade secrets and proprietary information that could be of benefit to our competitors regarding the design of our mobile device. This material is not customarily available to the general public and we request that it be withheld from public inspection. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name: Anil Tiwari Title: Vice President of Engineering 47071 Bayside Pkwy. Fremont, CA 94538 (510) 870-1264

FCC ID: PDC-ILM4X0GS A Trimble Company EXTERNAL PHOTOS OF EUT ( iLM4230) EUT iLM4230 – Top View FCC ID: PDC-ILM4X0GS A Trimble Company EUT iLM4230 – Bottom View EUT iLM4230 With Antenna FCC ID: PDC-ILM4X30GS A Trimble Company EXTERNAL PHOTOS OF EUT ( iLM4530) EUT iLM4530 – Top View FCC ID: PDC-ILM4X30GS A Trimble Company EUT iLM4530 – Bottom View EUT iLM4530 With Antenna

Labeling Requirement For iLM4230 Top Label Bottom label FCC ID: PDC-ILM4X30GS IC: 5079A-ILM4X30 WARNING: ALL PERSONS MUST KEEP A MINIMUM SEPARATION 20cm FROM THE TRANSMITTER’s ANTENNA WHEN DEVICE IS OPERATING TO MEET FCC RF EXPOSURE REQUIREMENT. Measurement in inches Width = 3.00” Height = 2.50” Corner radius = 0.125” Measurement in inches Width = 2.20” Height = 1.20” Corner radius=0.125” CDX0XXXX @Road, Inc. 1-877-4AtRoad www.road.com iLM4230

Labeling Requirement For iLM4530 Top Label Bottom label FCC ID: PDC-ILM4X30GS IC: 5079A-ILM4X30 WARNING: ALL PERSONS MUST KEEP A MINIMUM SEPARATION 20cm FROM THE TRANSMITTER’s ANTENNA WHEN DEVICE IS OPERATING TO MEET FCC RF EXPOSURE REQUIREMENT. Measurement in inches Width = 3.00” Height = 2.50” Corner radius = 0.125” Measurement in inches Width = 2.20” Height = 1.20” Corner radius=0.125” CDX5XXXX @Road, Inc. 1-877-4AtRoad www.road.com iLM4530

FCC ID: PDC-ILM4X30GS A Trimble Company INTERNAL PHOTOS OF EUT ( iLM4530) PCB 1 & PCB 2 VIEW - DISASSEMBLED PCB 1 & PCB 2 VIEW - ASSEMBLED PCB 1 PCB 2 PCB 1 PCB 2 FCC ID: PDC-ILM4X30GS A Trimble Company PCB 1 – TOP VIEW PCB 1 – BOTTOM VIEW FCC ID: PDC-ILM4X30GS A Trimble Company PCB 2 – TOP VIEW PCB 2 – BOTTOM VIEW GSM Module Antenna Connection

Siemens Cellular Engine TC63 Photos TC63: component side TC63: component side shielding opened TC63: rear side

FCC-ID PDC-ILM4X30GS IC-ID (Industry Canada) 5079A-ILM4X30 PREDICTION OF MPE AT A GIVEN DISTANCE Calculations can be made to predict RF field strength and power density levels around typical RF sources using the general equations (3) and (4) on page 19 of the following FCC document: “OET Bulletin 65, Edition 97-01 - Evaluating Compliance with FCC Guidelines for Human Exposure to Radio frequency Electromagnetic Fields”. These equations are generally accurate in the far field of an antenna but will over predict power density in the near field, where they could be used for making a “worst case” prediction. S = PG/4πR 2 (3) Where S = power density (in appropriate units, e.g. mW/cm 2 ) P = power input to the antenna (in appropriate units e.g. mW) G = power gain of the antenna in the direction of interest relative to the isotropic radiator R = distance to the center of radiation of the antenna (appropriate units e.g. cm) or, S = EIRP/4πR 2 (4) Where EIRP = Equivalent Isotropically radiated power General Limits: §1.1307 Cellular Radiotelephone Service (subpart H of part 22) Non-building-mounted antennas: height above ground level to lowest point of antenna < 10 m and total power of all channels > 1000 W ERP (1640 W EIRP) §1.1307 Personal Communications Services (part 24) Broadband PCS (subpart E): non-building-mounted antennas: height above ground level to lowest point of antenna < 10 m and total power of all channels > 2000 W ERP (3280 W EIRP) §1.1310 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) (B) Limits for General Population/Uncontrolled Exposure 300–1500 MHz: f/1500 mW/cm² 1500–100,000 MHz: 1.0 mW/cm² §2.1091 No routine evaluation required when the device ...operate at frequencies of 1.5 GHz or below and their effective radiated power (ERP) is 1.5 watts or more, or if they operate at frequencies above 1.5 GHz and their ERP is 3 watts or more. FCC-ID PDC-ILM4X30GS IC-ID (Industry Canada) 5079A-ILM4X30 §24.232 (a) Base stations are limited to 1640 watts peak equivalent isotropically radiated power (e.i.r.p.) with an antenna height up to 300 meters HAAT. b) Mobile/portable stations are limited to 2 watts e.i.r.p. peak power, ... §22.913 (a) Maximum ERP. The effective radiated power (ERP) of base transmitters and cellular repeaters must not exceed 500 Watts. The ERP of mobile transmitters and auxiliary test transmitters must not exceed 7 Watts. The table below is excerpted from Table 1B of 47 CFR 1.1310 titled “Limits for Maximum Permissible Exposure (MPE), Limits for General Population/Uncontrolled Exposure” Frequency Range (MHz) Power Density (mW/cm 2 ) 300 -1500 f/1500 1500 - 100000 1.0 Prediction for Part 22 Maximum radiated power EIRP: 27.07dBm (509mW) @ 836.6MHz Conducted Output Power is: 31.7dBm at 848.8MHz. (Test Report conducted 850.pdf page 11) Note: Antenna Option A has the highest predicted gain in the GSM850 band and is therefore used for measurements in that band. Lowest limit for 850 MHz fixed operations (@20cm) where no routine evaluation is required is § 1.1310: (f/1500)mW/cm 2 =0.5659 mW/cm 2 Calculated at distance of 20cm for reference antenna Option A: Power density = 509 / (4 x pi x 20 2 ) = 0.1012 mW/cm 2 G = 10 log (0.57mW/cm² x 4 x PI x 400cm²) – 31.7 dBm -2.14 dB = 0.73 dBd Lowest limit for 850 MHz mobile operations (@20cm) where no routine evaluation is required is § 2.1091 : 1.5W ERP G = 10 log 1500mW [ERP] – 31.7 dBm = 0.06 dBd Result: Configuration complies with rules as power density is below MPE limit. FCC-ID PDC-ILM4X30GS IC-ID (Industry Canada) 5079A-ILM4X30 Prediction for Part 24 Maximum radiated power EIRP: 22.93dBm (196mW) @1880MHz Conducted output power is: 28.7dBm (Test Report conducted 1900.pdf page 10) Note: Antenna Option J has the highest predicted gain in the GSM1900 band and is therefore used for measurements in that band. Lowest limit for 1900 MHz fixed operations (@20cm) where no routine evaluation is required is § 1.1310: 1 mW/cm 2 Calculated at distance of 20cm for reference antenna Option J: Power density = 196 / (4 x pi x 20 2 ) = 0.0390mW/cm 2 G = 10 log (1mW/cm² x 4 x PI x 400cm²) – 28.7 dBm = 8.3 dBi Lowest limit for 1900 MHz mobile operations (@20cm) where no routine evaluation is required is § 2.1091 : 3W ERP but §24.232 : 2W EIRP G = 10 log 2000mW [EIRP] – 28.7 dB = 4.31 dBi Result: Configuration complies with rules as power density is below MPE limit. Date: 2007-5-18 Name: Peter Mu Title: Project Engineer Company: Cetecom Inc. Address: 411 Dixon Landing Rd, Milpitas, CA 95035, USA Phone: +1 408 586 6221 Email: [email protected]

7 layers AG Aufsichtsratsvorsitzenderh Registergerichth registered in: Borsigstrasse 11 Chairman of the Supervisory Board: Düsseldorf, HRB 44096 40880 Ratingen, Germany Markus Becker USt-IdNr h VAT Nr: Phone: +49 (0) 2102 749 0 Vorstandh Board: DE 203159652 Fax: +49 (0) 2102 749 350 Dr. Hans-Jürgen Meckelburg www.7Layers.com René Schildknecht InterLab ® is a registered trademark of 7 layers AG FCC Measurement/Technical Report on GSM Module MC75 Siemens Cellular Engine MC75 Report Reference: 4_SIEM_0504_GSM_FCCm Test Laboratory: 7 layers AG Borsigstrasse 11 40880 Ratingen Germany email: [email protected] DAT-P-192/99-01 Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the testing laboratory. Test report Reference: 4_SIEM_0504_GSM_FCCm Page 2 of 53 Table of Contents 0 Summary 3 0.1 Technical Report Summary 3 0.2 Measurement Summary 4 1 Administrative Data 6 1.1 Testing Laboratory 6 1.2 Project Data 6 1.3 Applicant Data 6 1.4 Manufacturer Data 6 2 Testobject Data 7 2.1 General EUT Description 7 2.2 EUT Main components 8 2.3 Ancillary Equipment 8 2.4 EUT Setups 8 2.5 Operating Modes 9 3 Test Results 10 3.1 RF Power Output 10 3.2 Frequency stability 14 3.3 Spurious emissions at antenna terminals 18 3.4 Field strength of spurious radiation 22 3.5 Emission and Occupied Bandwidth 26 3.6 Mobile emissions in base frequency range 30 4 Test Equipment 33 5 Photo Report 36 6 Setup Drawings 40 7 Annex 42 Measurement Plots Test report Reference: 4_SIEM_0504_GSM_FCCm Page 3 of 53 0 Summary 0.1 Technical Report Summary Type of Authorization Certification for a GSM cellular radiotelephone device Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 0 to 19 and Parts 20 to 69 (10-1-04 Edition). The following subparts are applicable to the results in this test report. Part 2 Subpart J - Equipment Authorization Procedures, Certification § 2.1046 Measurement required: RF power output § 2.1049 Measurement required: Occupied bandwidth § 2.1051 Measurement required: Spurious emissions at antenna terminals § 2.1053 Measurement required: Field strength of spurious radiation § 2.1055 Measurement required: Frequency stability § 2.1057 Frequency spectrum to be investigated Part 22 Subpart C – Operational and Technical Requirements § 22.355 Frequency tolerance Subpart H – Cellular Radiotelephone Service § 22.913 Effective radiated power limits § 22.917 Emission limitations for cellular equipment Summary Test The EUT complied with all performed tests as listed in chapter 0.2 Measurement Summary. Test report Reference: 4_SIEM_0504_GSM_FCCm Page 4 of 53 0.2 Measurement Summary RF Power Output The measurement was performed according to FCC §2.1046 10-01-2004 OP-Mode Setup Port Final Result op-mode 1 Setup_a03 antenna connector passed op-mode 2 Setup_a03 antenna connector passed op-mode 3 Setup_a03 antenna connector passed op-mode 4 Setup_a01 antenna connector passed op-mode 5 Setup_a01 antenna connector passed op-mode 6 Setup_a01 antenna connector passed Frequency stability The measurement was performed according to FCC §2.1055 10-01-2004 OP-Mode Setup Port Final Result op-mode 2 Setup_a01 antenna connector passed op-mode 5 Setup_a01 antenna connector passed Spurious emissions at antenna terminals The measurement was performed according to FCC §2.1051 10-01-2004 OP-Mode Setup Port Final Result op-mode 1 Setup_a03 antenna connector passed op-mode 2 Setup_a03 antenna connector passed op-mode 3 Setup_a03 antenna connector passed op-mode 4 Setup_a01 antenna connector passed op-mode 5 Setup_a01 antenna connector passed op-mode 6 Setup_a01 antenna connector passed Field strength of spurious radiation The measurement was performed according to FCC §2.1053 10-01-2004 OP-Mode Setup Port Final Result op-mode 1 Setup_a02 enclosure passed op-mode 2 Setup_a02 enclosure passed op-mode 3 Setup_a02 enclosure passed op-mode 4 Setup_a02 enclosure passed op-mode 5 Setup_a02 enclosure passed op-mode 6 Setup_a02 enclosure passed Emission and Occupied Bandwidth The measurement was performed according to FCC §2.1049 10-01-2004 OP-Mode Setup Port Final Result op-mode 1 Setup_a01 antenna connector passed op-mode 2 Setup_a01 antenna connector passed op-mode 3 Setup_a01 antenna connector passed op-mode 4 Setup_a01 antenna connector passed op-mode 5 Setup_a01 antenna connector passed op-mode 6 Setup_a01 antenna connector passed Test report Reference: 4_SIEM_0504_GSM_FCCm Page 6 of 53 1 Administrative Data 1.1 Testing Laboratory Company Name: 7 Layers AG Address Borsigstr. 11 40880 Ratingen Germany This facility has been fully described in a report submitted to the FCC and accepted under the registration number 96716 . The test facility is also accredited by the following accreditation organisation: - Deutscher Akkreditierungs Rat DAR-Registration no. DAT-P-192/99-01 Responsible for Accreditation Scope: Dipl.-Ing. Bernhard Retka Dipl.-Ing. Arndt Stöcker Dipl.-Ing. Thomas Hoell Report Template Version: 2005-10-10 1.2 Project Data Responsible for testing and report: Dipl.-Ing. Robert Machulec Receipt of EUT: 2005-12-06 Date of Test(s): 2005-12-16 to 2006-04-04 Date of Report: 2006-04-05 1.3 Applicant Data Company Name: Siemens AG Address: Siemensdamm 50 13629 Berlin Germany Contact Person: Thorsten Liebig 1.4 Manufacturer Data Company Name: please see applicant data Address: Contact Person: Test report Reference: 4_SIEM_0504_GSM_FCCm Page 7 of 53 2 Testobject Data 2.1 General EUT Description Equipment under GSM Module MC75 Type Designation: Siemens Cellular Engine MC75 Kind of Device: (optional) GSM 850/900/1800/1900 with EDGE Voltage Type: DC Nominal Voltage: 4,5 V Maximum Voltage: 4,5 V Minimum Voltage: 3,2 V General product description: The Equipment Under Test (EUT) is a GSM 850/900/1800/1900 with EDGE phone module. In GSM 850 mode the EUT operates in channel blocks …

Text truncated - open the document above for the full version.

Annex I: band edge compliance Measurement plots Test report reference: 4_SIEM_0504_GSM_FCCm Date: 2006-01-06 Annex I: band edge compliance - Measurement plots Test report reference: 4_SIEM_0504_GSM_FCCm Page 2 of 5 A 36 dB Offset Unit dBm EXT 1MAX1MA Start 823 MHzStop 824 MHz100 kHz/ Ref Lvl 35 dBm Ref Lvl 35 dBm RF Att 20 dBRBW 3 kHz VBW 3 kHz SWT 280 ms IN1 -60 -50 -40 -30 -20 -10 0 10 20 30 -65 35 1 Marker 1 [T1] -13.35 dBm 823.98196393 MHz 1 [T1] -13.35 dBm 823.98196393 MHz D1 -13 dBm Date: 21.DEC.2005 13:48:48 Test: band edge compliance , Channel 128, PCS Annex I: band edge compliance - Measurement plots Test report reference: 4_SIEM_0504_GSM_FCCm Page 3 of 5 A 36 dB Offset Unit dBm 1MAX1MA EXT Start 823 MHzStop 824 MHz100 kHz/ Ref Lvl 35 dBm Ref Lvl 35 dBm RBW 3 kHz VBW 3 kHz SWT 280 ms RF Att 20 dB IN1 -60 -50 -40 -30 -20 -10 0 10 20 30 -65 35 1 Marker 1 [T1] -20.91 dBm 823.99198397 MHz 1 [T1] -20.91 dBm 823.99198397 MHz D1 -13 dBm Date: 21.DEC.2005 14:09:20 Test: band edge compliance , Channel 128, EDGE Annex I: band edge compliance - Measurement plots Test report reference: 4_SIEM_0504_GSM_FCCm Page 4 of 5 A 36 dB Offset Unit dBm 1MAX1MA Ref Lvl 35 dBm Ref Lvl 35 dBm RF Att 20 dB EXT Start 849 MHzStop 850 MHz100 kHz/ RBW 3 kHz VBW 3 kHz SWT 280 ms IN1 -60 -50 -40 -30 -20 -10 0 10 20 30 -65 35 1 Marker 1 [T1] -13.13 dBm 849.02204409 MHz 1 [T1] -13.13 dBm 849.02204409 MHz D1 -13 dBm Date: 21.DEC.2005 13:50:36 Test: band edge compliance, Channel 251, PCS Annex I: band edge compliance - Measurement plots Test report reference: 4_SIEM_0504_GSM_FCCm Page 5 of 5 A 36 dB Offset Unit dBm 1MAX1MA EXT Start 849 MHzStop 850 MHz100 kHz/ Ref Lvl 35 dBm Ref Lvl 35 dBm RBW 3 kHz VBW 3 kHz SWT 280 ms RF Att 20 dB IN1 -60 -50 -40 -30 -20 -10 0 10 20 30 -65 35 1 Marker 1 [T1] -20.75 dBm 849.03006012 MHz 1 [T1] -20.75 dBm 849.03006012 MHz D1 -13 dBm Date: 21.DEC.2005 14:12:14 Test: band edge compliance, Channel 251, EDGE

7 layers AG Aufsichtsratsvorsitzenderh Registergerichth registered in: Borsigstrasse 11 Chairman of the Supervisory Board: Düsseldorf, HRB 44096 40880 Ratingen, Germany Markus Becker USt-IdNr h VAT Nr: Phone: +49 (0) 2102 749 0 Vorstandh Board: DE 203159652 Fax: +49 (0) 2102 749 350 Dr. Hans-Jürgen Meckelburg www.7Layers.com René Schildknecht InterLab ® is a registered trademark of 7 layers AG FCC Measurement/Technical Report on GSM Module MC75 Siemens Cellular Engine MC75 Report Reference: 4_SIEM_0504_GSM_FCCn Test Laboratory: 7 layers AG Borsigstrasse 11 40880 Ratingen Germany email: [email protected] DAT-P-192/99-01 Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the testing laboratory. Test report Reference: 4_SIEM_0504_GSM_FCCn Page 2 of 49 Table of Contents 0 Summary 3 0.1 Technical Report Summary 3 0.2 Measurement Summary 4 1 Administrative Data 5 1.1 Testing Laboratory 5 1.2 Project Data 5 1.3 Applicant Data 5 1.4 Manufacturer Data 5 2 Testobject Data 6 2.1 General EUT Description 6 2.2 EUT Main components 7 2.3 Ancillary Equipment 7 2.4 EUT Setups 7 2.5 Operating Modes 8 3 Test Results 9 3.1 RF Power Output 9 3.2 Frequency stability 13 3.3 Spurious emissions at antenna terminals 17 3.4 Field strength of spurious radiation 21 3.5 Emission and Occupied Bandwidth 25 4 Test Equipment 29 5 Photo Report 32 6 Setup Drawings 36 7 Annex 38 Measurement Plots Test report Reference: 4_SIEM_0504_GSM_FCCn Page 3 of 49 0 Summary 0.1 Technical Report Summary Type of Authorization Certification for a GSM cellular radiotelephone device Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 0 to 19 and Parts 20 to 69 (10-1-04 Edition). The following subparts are applicable to the results in this test report. Part 2 Subpart J - Equipment Authorization Procedures, Certification § 2.1046 Measurement required: RF power output § 2.1049 Measurement required: Occupied bandwidth § 2.1051 Measurement required: Spurious emissions at antenna terminals § 2.1053 Measurement required: Field strength of spurious radiation § 2.1055 Measurement required: Frequency stability § 2.1057 Frequency spectrum to be investigated Part 24 Subpart E - Broadband PCS § 24.232 Power and antenna height limits § 24.235 Frequency stability § 24.236 Field strength limits § 24.238 Emission limitations for Broadband PCS equipment Summary Test Results: The EUT complied with all performed tests as listed in chapter 0.2 Measurement Summary. Test report Reference: 4_SIEM_0504_GSM_FCCn Page 5 of 49 1 Administrative Data 1.1 Testing Laboratory Company Name: 7 Layers AG Address Borsigstr. 11 40880 Ratingen Germany This facility has been fully described in a report submitted to the FCC and accepted under the registration number 96716 . The test facility is also accredited by the following accreditation organisation: - Deutscher Akkreditierungs Rat DAR-Registration no. DAT-P-192/99-01 Responsible for Accreditation Scope: Dipl.-Ing. Bernhard Retka Dipl.-Ing. Arndt Stöcker Dipl.-Ing. Thomas Hoell Report Template Version: 2005-10-10 1.2 Project Data Responsible for testing and report: Dipl.-Ing. Robert Machulec Receipt of EUT: 2005-12-06 Date of Test(s): 2005-12-16 to 2006-04-04 Date of Report: 2006-04-05 1.3 Applicant Data Company Name: Siemens AG Address: Siemensdamm 50 13629 Berlin Germany Contact Person: Thorsten Liebig 1.4 Manufacturer Data Company Name: please see applicant data Address: Contact Person: Test report Reference: 4_SIEM_0504_GSM_FCCn Page 6 of 49 2 Testobject Data 2.1 General EUT Description Equipment under GSM Module MC75 Type Designation: Siemens Cellular Engine MC75 Kind of Device: (optional) GSM 850/900/1800/1900 with EDGE Voltage Type: DC Nominal Voltage: 4.5 V Maximum Voltage: 4.5 V Minimum Voltage: 3.2 V General product description: The Equipment Under Test (EUT) is a GSM 850/900/1800/1900 with EDGE. In PCS1900 mode the EUT operates in blocks A through F from 1850.2 MHz (lowest channel = 512) to 1909.8 MHz (highest channel = 810). The EUT provides the following ports: Ports antenna connector enclosure control connector The main components of the EUT are listed and described in Chapter 2.2 Test report Reference: 4_SIEM_0504_GSM_FCCn Page 7 of 49 2.2 EUT Main components Type, S/N, Short Descriptions etc. used in this Test Report Short Description Equipment under Test Type Designation Serial No. HW Status SW Status Date of Receipt EUT A (1400AC15) GSM Phone module MC75 344868 B2.11 02.050 2005-12-06 Remark: EUT A is connected to the development board. The SMA antenna connector is provided by the development board. For radiated tests an external antenna will be used additionally. EUT B (1400AH18) GSM Phone module MC75 344865 B2.11 02.171 2006-02-20 Remark: EUT B is connected to the development board. The SMA antenna connector is provided by the development board. For radiated tests an external antenna will be used additionally. NOTE: The short description is used to simplify the identification of the EUT in this test report. 2.3 Ancillary Equipment For the purposes of this test report, ancillary equipment is defined as equipment which is used in conjunction with the EUT to provide operational and control features to the EUT. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Ancillary Equipment can influence the test results. Short Description Equipment under Test Type Designation HW Status SW Status Serial no. FCC ID AE1 Allgon- MiniMAG Dualband Antenna Ordering number: 1140.26 – – EMV Referenz Antenne No.02 – AE2 Develop- ment Board DSB75 – – B1 0077 – 2.4 EUT Setups This chapter describes the combination of EUT's and ancillary equipment used for testing. Setup No. Combination of EUTs Description setup_a01 EUT A + AE2 setup for conducted tests setup_a02 EUT A + AE1 + AE2 setup…

Text truncated - open the document above for the full version.

Annex I: band edge compliance Measurement plots Test report reference: 4_SIEM_0504_GSM_FCCn Date: 2006-01-06 Annex I: band edge compliance - Measurement plots Test report reference: 4_SIEM_0504_GSM_FCCn Page 2 of 5 A 36 dB Offset Unit dBm 1MAX1MA EXT Start 1.849 GHzStop 1.85 GHz100 kHz/ Ref Lvl 35 dBm Ref Lvl 35 dBm RBW 3 kHz VBW 3 kHz SWT 280 ms RF Att 20 dB IN1 -60 -50 -40 -30 -20 -10 0 10 20 30 -65 35 1 Marker 1 [T1] -16.24 dBm 1.84999800 GHz 1 [T1] -16.24 dBm 1.84999800 GHz D1 -13 dBm Date: 21.DEC.2005 13:53:47 Test: band edge compliance , Channel 512,PCS Annex I: band edge compliance - Measurement plots Test report reference: 4_SIEM_0504_GSM_FCCn Page 3 of 5 A 36 dB Offset Unit dBm EXT Ref Lvl 35 dBm Ref Lvl 35 dBm RF Att 20 dB 1MAX1MA Start 1.849 GHzStop 1.85 GHz100 kHz/ RBW 3 kHz VBW 3 kHz SWT 280 ms IN1 -60 -50 -40 -30 -20 -10 0 10 20 30 -65 35 1 Marker 1 [T1] -23.28 dBm 1.84997996 GHz 1 [T1] -23.28 dBm 1.84997996 GHz D1 -13 dBm Date: 21.DEC.2005 14:16:45 Test: band edge compliance , Channel 512, EDGE Annex I: band edge compliance - Measurement plots Test report reference: 4_SIEM_0504_GSM_FCCn Page 4 of 5 A 36 dB Offset Unit dBm 1MAX1MA Ref Lvl 35 dBm…

Text truncated - open the document above for the full version.