PDC-IWM314XSWMobile Internet Location MGR

Confidential Information 1 PN: 900-003x-000 DRAFT © 2002 At Road, Inc. All Rights Reserved @Road iWM3100 Series Installation Guide Important – Please Read! FCC Information This device complies with Part 15 of FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference that may cause undesired operation. Warning: The antenna supplied with this device must be used for installation and operation. Substitution of other antennas must be approved by the manufacturer for compliance to radiation safety limits. The mounting of this device and antenna must be done by professional installers to ensure that the user or nearby persons will maintain at least 20 cm from the antenna in normal use. Cautions: Any changes or modifications not expressly approved by @Road could void the user's authority to operate the equipment. BEFORE THE INSTALLATION ¾ Gather Components Please ensure you have the following items are together before beginning the installation. There should be one complete set for each vehicle being installed. If any items are missing, contact a local Agent or @Road immediately. 1. iWM31XX Unit 2. Power Cable 3. Installation Parts Kit 4. One of following Antenna should be used o Mobile Mark Multi-band GPS/CELL/PCS/WIFI antenna, P/N: SMW-UMW- 1A3J2C 5. Installation Information Sheet, 4 part carbon (packaged with iWM Unit) Following the simple steps below will ensure optimum performance of your iWM unit. Should you have questions, please contact @Road Customer Service toll-free at 1-877-4-AtRoad (1-877-428-7623). Confidential Information 2 PN: 900-003x-000 DRAFT © 2002 At Road, Inc. All Rights Reserved ¾ BEFORE YOU CONTINUE Verify/Match Unit to Correct Vehicle NOTE: Some iWM’s are pre-matched to vehicle by number. This must be known before beginning the installation. 1) Check with the customer to see if vehicles were pre-matched by name/VIN/Serial Number. 2) Fill out the Installation Information Sheet noting iWM ID’s to Vehicles by VIN, License or Car Number . This information is required for the customer to track their vehicles. iWM3100 Assembly and External Interface Detail BEGINNING THE INSTALLATION Input Power (10 ~ 24VDC, 2A) PCS/Cellular Antenna GPS Antenna WLAN Antenna Ethernet Port Data 1 & 2 Ports PTO Switches Port CELL/PCS Diversity Antenna 3140 Confidential Information 3 PN: 900-003x-000 DRAFT © 2002 At Road, Inc. All Rights Reserved 1) Choose a Location Determine the best location to install the iWM unit. Recommendations are: • In the trunk, where luggage and other items will not come into contact with the unit • Behind or under the seats • Under or behind the dashboard • Behind the left or right kick-panels • In the console (side or overhead) • In the glove compartment/glove box • Hidden from driver’s view when possible, to limit driver tampering 2) Mount the iWM Unit The iWM should be mounted using screws or tie-wraps 3) Hook Up Power The iWM should be connected directly to a known 12V-DC power source (range of 10 to 24VDC), either the column harness or battery of the vehicle. Although the unit has a built-in self-resetting fuse, the iWM3100’s power cable must be fused protected at the power source on both the RED and WHITE power connections with the 10 amp fuses and fuse holders, included in the installation kit. Additionally, remember to place the tamper resistant sticker and PLEASE NOTE: Placement should: • Avoid direct sunlight • Provide minimal exposure to dust • Ensure minimal exposure to moisture • Never be installed in engine compartment (Unit is designed to be installed inside the vehicle) iWM3100Installation Side View It is essential that you follow these steps exactly, as any inaccuracies may cause hardware damage and the @Road system to malfunction. Confidential Information 4 PN: 900-003x-000 DRAFT © 2002 At Road, Inc. All Rights Reserved a tie wrap over the cover of the fuse holder, as shown in the following picture, so that any tampering with power source wires can be easily detected. Use a voltmeter to verify voltage and hook wires as indicated below. Black Ground Red (fused, 10 Amps) to vehicle battery, unswitched (+), this wire must see at least 10 volts at all times, if not the unit will reset continually and send inaccurate information White (fused, 10 Amps) To true ignition, 12V switched, there must be 12 volt power in the “on”, “start”, and “run” position. All connections at the column harness must be made by either soldering bare wire to bare wire or using the poke and wrap method. Note: T-taps, scotch locks, and like connectors are not permitted and must not be used to tie the iWM to its power source. 4) Position GPS Antenna for Optimum Performance To ensure best reception, install the GPS antenna in a location that provides a clear sky view (greater than a 90 degree angle view of the sky). Note: Mount antenna as far as Confidential Information 5 PN: 900-003x-000 DRAFT © 2002 At Road, Inc. All Rights Reserved possible (at least 2 feet) away from other antennas to minimize the possibility of interference. SMALL VEHICLE (A) BEST – Top of vehicle (B) Option – Dashboard of vehicle (C) Option – Rear brake light compartment (must be non-metallic) Could be on the dashboard or hidden Place under the rear brake light. under non-metallic dashboard. The Can be accessed through the trunk. antenna must face toward the sky. Only recommended when the rear window has a steep slope. LARGE VEHICLE (A) BEST – Top of the vehicle and as (B) OPTION – Middle of the roof close to the front as possible THIS POSITION NOT RECOMMENDED (due to restricted sky view) 5) Connect GSM and WLAN Antenna (if separate GSM antenna or non- combo antenna) The GSM antenna should be installed in an optimum location, to intercept the cellular signals, arriving at slightly above zero degrees from the horizon. Signals will typically penetrate through non-metal material such as glass, fiberglass, and alum…

Text truncated - open the document above for the full version.

1 Mike Kuo From: Danielle Zhan Sent: Tuesday, June 14, 2005 11:32 AM To: Mike Kuo Cc: Thu Chan; Michael Heckrotte; Barbara Judge Subject: RE: AT ROAD, Inc., FCC ID: PDC-IWM314XSW, Assessment NO.: AN05T4842, Notice#1 Attachments: 05U3362-1B FCC DTS Report_Revised.pdf; ILM3140_Series_InstallerGuide.revised.pdf; iWM3140_Ant_Gain_Calculation.pdf Hi Mike, Please find responses to your questions /comments contained below in blue. Thanks for your further review, Danielle Zhan Compliance Certification Services 561 F Monterey Road Morgan Hill, CA 95037 Tel: (408) 463 0885 Fax: (408) 463 0888 -----Original Message----- From: Mike Kuo Sent: Friday, June 10, 2005 2:39 PM To: Danielle Zhan Cc: Thu Chan; Michael Heckrotte; Barbara Judge Subject: FW: AT ROAD, Inc., FCC ID: PDC-IWM314XSW, Assessment NO.: AN05T4842, Notice#1 Best Regards Mike Kuo Compliance Certification Services 561F Monterey Road Morgan Hill CA 95037 Tel: (408)463-0885 x: 105 Fax: (408)463-0888 http://www.ccsemc.com -----Original Message----- From: Compliance Certification Services [mailto:[email protected]] Sent: Friday, June 10, 2005 3:32 PM To: Mike Kuo Subject: AT ROAD, Inc., FCC ID: PDC-IWM314XSW, Assessment NO.: AN05T4842, Notice#1 Question #1: Based upon the information submitted, this Mobile Internet Location unit is equipped with two radios. One is Licensed Part 22/24 module under FCC ID:N7N-EM5625D and unlicensed WLAN module under FCC ID:M4Y-000325. The proposed FCC ID is on the Mobile Internet Location unit under the grantee code of applicant. 2 With above understanding in mind, this application must be filed as composite device. One unlicensed 15.247 DTS application ( submitted, under assessment no:AN05T4842 ) and the other licensed PCS base station ( which has not been submitted ). Please submit another TCB application for licensed portion. [Danielle] Another TCB application for the licesed portion has been filed under assessment No.: AN05T4857 on 6/10/05 for your review. Question #2: In the FCC 15.247 DTS report submitted in this application, page 26 indicates that there is co-located radiated spurious emission was performed. However, such co-located test data can not be found. Please explain. [Danielle] The co-loca ted spurious emissions section has been removed from the report. Please see revised FCC report as attached and also be noted that the antenna gain has been revised in the test report based on the additional antenna info provided by client. 05U3362-1B FCC DTS Report_Revi... Question #3: User manual does not contain information required under section 15.21 and 15.19 (3) of FCC rules. Please submit revised user manual to address these two requirements. [Danielle] FCC rules 15.21 and 15.19 (3) have been added into the user manual, please see revised as attached. ILM3140_Series_In stallerGuide.... Question #4: MPE estimate, when there are multiple radios installed in a single enclosure, MPE estimate shall take into account when multiple transmitters are transmitting at the same time. The power density of combined far field radiation must be considered. Please provide revised MPE estimate. [Danielle] A co-located Maximum Permissible Exposure section has been added to the report, same as attached above. Question #5: The antenna gain indicated in the test report is 2.5dBi which does not agree with antenna specification for 2.4GHz band. Please explain. [Danielle] An additional antenna info has been provided as attached. The gain (5 dBi for 2.4 GHz band) indicated in the antenna spec is without cable loss(3.3 dBi), so the actual gain for 2.4 GHz band is 1.7 dBI. Please see attached for antenna gain with and without cable loss. iWM3140_Ant_Gain _Calculation.p... Part 22/24 portion: Question #6: Based upon the original grant under FCC ID:N7N-EM5625D, the max. allowed antenna gain for cellular band is 5.1dBi and for PCS band is 3.9dBi. In accordance with antenna specification submit, the gain for PCS band is 5 dBi. There is no document submitted to justify the higher antenna gain for PCS band used by the applicant. Please explain. [Danielle] Please see the additional antenna info, same as attached above. The gain (2 dBi for Cellular band) indicated in the antenna spec is without cable loss(2.25 dBi), so the actual gain for the cellular band is -0.25 dBI; while the gain (5 dBi for PCS band) indicated in the antenna spec is without cable loss(3.3 dBi), so the actual gain for the PCS band is 1.7 dBI. The test report has also been updated too accordingly. Best Regards 3 Mike Kuo The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 30 days of the original e-mail date may result in application dismissal and forfeiture of the filing fee. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the e-mail address listed below the name of the sender.

47071 Bayside Pkwy, Fremont, CA 94538 - Tel: (510)668-1638 Date: 6/10/2005 Subject: Calculate Antenna Gain for iWM3140 Device. Antenna Manufacture: Mobile Mark Communication Antennas Model: SMW-UMB-1A3J2C Descriptions: Multi-band Surface Mount Antenna Cellular/DCS/PCS/GPS and 2.4 GHz. Gain Specification Without Cable Loss Band 1, 806 to 960 MHz : 2 dBi Band 2, 1710 to 1990 MHz: 5dBi Band 3, 2400 to 2585 MHz: 5dBi Cable Loss Band 1, 806 to 960 MHz : 2.25 dB Band 2, 1710 to 1990 MHz: 3.3 dB Band 3, 2400 to 2585 MHz: 3.3 dB Actual Estimated Antenna Gain Band 1, 806 to 960 MHz : -0.25 dBi Band 2, 1710 to 1990 MHz: 1.7dBi Band 3, 2400 to 2585 MHz: 1.7dBi

FCC ID: PDC-IWM314XSW EXTERNAL PHOTOS OF EUT ( iWM3140) iWM3140 – TOP VIEW iWM3140 – BOTTOM VIEW FCC ID: PDC-IWM314XSM IC 5078A-IWM314XS

1 ANNEX PHOTOGRAPHS OF EUT 2 3 4

Labeling Requirement For iWM3140 Top Label Bottom label This device complies with Part 15 of FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference that may cause undesired operation. WARNING: ALL PERSONS MUST KEEP A MINIMUM SEPARATION 20cm FROM THE TRANSMITTER’s ANTENNA WHEN DEVICE IS OPERATING TO MEET FCC RF EXPOSURE REQUIREMENT. 0410180027 Assembled in China Measurement in inches Width = 3.50” Height = 2.20” Corner radius = 0.125” Measurement in inches Width = 3.50” Height = 2.75” Corner radius = 0.125” AP FCC ID: PDC-IWM314XSW EXTERNAL PHOTOS OF EUT ( iWM3140) iWM3140 – TOP VIEW iWM3140 – BOTTOM VIEW FCC ID: PDC-IWM314XSM IC 5078A-IWM314XS

5 6 7

8 9

FCC CFR47 PART 15 SUBPART C CERTIFICATION TEST REPORT FOR MOBILE INTERNET LOCATION MGR MODEL NUMBER: iWM3140 FCC ID: PDC-FWM314XSM REPORT NUMBER: 05U3362-1B ISSUE DATE: JUNE 10, 2005 Prepared for AT ROAD, INC. 47071 BAYSIDE PKWY FREMONT, CA 94538, USA Prepared by COMPLIANCE ENGINEERING SERVICES, INC. d.b.a. COMPLIANCE CERTIFICATION SERVICES 561F MONTEREY ROAD, MORGAN HILL, CA 95037, USA TEL: (408) 463-0885 FAX: (408) 463-0888 REPORT NO: 05U3362-1B DATE: JUNE 10, 2005 EUT: MOBILE INTERNET LOCATION MGR FCC ID: PDC-FWM314XSM Revision History Rev. Revisions Revised By B Removed Co-Located Spurious Emissions Section Thu Added Co-Located Maximum Permissible Exposure Thu REPORT NO: 05U3362-1B DATE: JUNE 10, 2005 EUT: MOBILE INTERNET LOCATION MGR FCC ID: PDC-FWM314XSM Page 3 of 42 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS............................................................................................. 4 2. TEST METHODOLOGY .................................................................................................................. 5 3. FACILITIES AND ACCREDITATION .......................................................................................... 5 4. CALIBRATION AND UNCERTAINTY.......................................................................................... 5 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................................. 5 4.2. MEASUREMENT UNCERTAINTY ............................................................................................... 5 5. EQUIPMENT UNDER TEST............................................................................................................6 5.1. DESCRIPTION OF EUT ..............................................................................................................6 5.2. ADDITIONAL TESTING............................................................................................................... 6 5.3. MAXIMUM OUTPUT POWER .................................................................................................... 6 5.4. DESCRIPTION OF AVAILABLE ANTENNAS ............................................................................. 7 5.5. SOFTWARE AND FIRMWARE .................................................................................................... 7 5.6. WORST-CASE CONFIGURATION AND MODE......................................................................... 7 5.7. MODIFICATIONS ........................................................................................................................ 7 5.8. DESCRIPTION OF TEST SETUP ................................................................................................ 8 6. TEST AND MEASUREMENT EQUIPMENT .............................................................................. 10 7. LIMITS AND RESULTS ................................................................................................................. 11 7.1. CHANNEL TESTS FOR THE 2400 TO 2483.5 MHz BAND ...................................................... 11 7.1.1. 99% BANDWIDTH............................................................................................................ 11 7.1.2. PEAK OUTPUT POWER .................................................................................................. 15 7.1.3. MAXIMUM PERMISSIBLE EXPOSURE ........................................................................ 20 7.1.4. CO-LOCATED MAXIMUM PERMISSIBLE EXPOSURE ............................................. 23 7.1.5. AVERAGE POWER........................................................................................................... 26 7.2. RADIATED EMISSIONS FOR THE 2400 TO 2483.5 MHz BAND ............................................ 27 7.2.1. TRANSMITTER RADIATED SPURIOUS EMISSIONS ................................................. 27 7.2.2. TRANSMITTER ABOVE 1 GHz ...................................................................................... 30 7.2.3. WORST-CASE RADIATED EMISSIONS BELOW 1 GHz ............................................. 39 8. SETUP PHOTOS .............................................................................................................................. 40 REPORT NO: 05U3362-1B DATE: JUNE 10, 2005 EUT: MOBILE INTERNET LOCATION MGR FCC ID: PDC-FWM314XSM Page 4 of 42 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: AT ROAD, INC. 47071 BAYSIDE PKWY FREMONT, CA. 94538, USA EUT DESCRIPTION: Mobile Internet Location MGR MODEL: iWM3140 SERIAL NUMBER: 0503310396 DATE TESTED: May 15 - 16, 2005 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 15 SUBPART C NO NON-COMPLIANCE NOTED Compliance Certification Services, Inc. tested the above equipment in accordance with the requirements set forth in the above standards. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by Compliance Certification Services and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by Compliance Certification Services will constitute fraud and shall nullify the document. No part of this report may be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any government agency…

Text truncated - open the document above for the full version.

FCC ID: M4Y-000325 Report No.: RF900628R02 1 Issued: August 13, 2001 FCC TEST REPORT REPORT NO.: RF900628R02 MODEL NO.: XI-325, XI-325B RECEIVED: June 28, 2001 TESTED: July 2 ~ August 9, 2001 APPLICANT: Z-COM, INC. ADDRESS: 7F-2, No.9, Prosperity RD. I, Science-Based Industrial Park Hsinchu, 300 Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB LOCATION: 47 14th Lin, Chiapau Tsun, Linko, Taipei, Taiwan, R.O.C. This test report consists of 62 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, NVLAP or any government agencies. The test results in the report only apply to the tested sample. 0528 Lab Code: 200102-0 FCC ID: M4Y-000325 Report No.: RF900628R02 2 Issued: August 13, 2001 Table of Contents 1CERTIFICATION ........................................................................................... 4 2SUMMARY OF TEST RESULTS ................................................................... 5 3GENERAL INFORMATION............................................................................ 6 3.1GENERAL DESCRIPTION OF EUT.............................................................. 6 3.2DESCRIPTION OF TEST MODES ................................................................ 7 3.3GENERAL DESCRIPTION OF APPLIED STANDARDS ............................... 7 3.4DESCRIPTION OF SUPPORT UNITS .......................................................... 8 4TEST TYPES AND RESULTS ....................................................................... 9 4.1CONDUCTED EMISSION MEASUREMENT ................................................ 9 4.1.1LIMITS OF CONDUCTED EMISSION MEASUREMENT .............................. 9 4.1.2TEST INSTRUMENTS................................................................................... 9 4.1.3TEST PROCEDURES ................................................................................. 10 4.1.4TEST SETUP .............................................................................................. 10 4.1.5EUT OPERATING CONDITIONS ................................................................ 11 4.1.6TEST RESULTS(A) ..................................................................................... 12 4.1.7TEST RESULTS(B) ..................................................................................... 18 4.2RADIATED EMISSION MEASUREMENT ................................................... 24 4.2.1LIMITS OF RADIATED EMISSION MEASUREMENT ................................. 24 4.2.2TEST INSTRUMENTS................................................................................. 25 4.2.3TEST PROCEDURES ................................................................................. 26 4.2.4TEST SETUP .............................................................................................. 27 4.2.5EUT OPERATING CONDITIONS ................................................................ 27 4.2.6TEST RESULTS(A) ..................................................................................... 28 4.2.7TEST RESULTS(B) ..................................................................................... 33 4.36DB BANDWIDTH MEASUREMENT .......................................................... 38 4.3.1LIMITS OF 6dB BANDWIDTH MEASUREMENT ........................................ 38 4.3.2TEST INSTRUMENTS................................................................................. 38 4.3.3TEST PROCEDURE.................................................................................... 39 4.3.4TEST SETUP .............................................................................................. 39 4.3.5EUT OPERATING CONDITIONS ................................................................ 39 4.3.6TEST RESULTS .......................................................................................... 40 4.4MAXIMUM PEAK OUTPUT POWER .......................................................... 44 4.4.1LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT ........... 44 4.4.2TEST INSTRUMENTS................................................................................. 44 4.4.3TEST PROCEDURES ................................................................................. 45 FCC ID: M4Y-000325 Report No.: RF900628R02 3 Issued: August 13, 2001 4.4.4TEST SETUP .............................................................................................. 45 4.4.5EUT OPERATING CONDITIONS ................................................................ 45 4.4.6TEST RESULTS .......................................................................................... 46 4.5POWER SPECTRAL DENSITY MEASUREMENT ...................................... 47 4.5.1LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT ................... 47 4.5.2TEST INSTRUMENTS................................................................................. 47 4.5.3TEST PROCEDURE.................................................................................... 48 4.5.4TEST SETUP .............................................................................................. 48 4.5.5EUT OPERATING CONDITIONS ................................................................ 48 4.5.6TEST RESULTS .......................................................................................... 49 4.6BAND EDGES MEASUREMENT ................................................................ 53 4.6.1LIMITS OF BAND EDGES MEASUREMENT .............................................. 53 4.6.2TEST INSTRUMENTS................................................................................. 53 4.6.3TEST PROCEDURE.................................................................................... 53 4.6.4EUT OPERATING CONDITION .................................................................. 54 4.6.5TEST RESULTS ........…

Text truncated - open the document above for the full version.

FCC ID: M4Y-000325 Report No.: RF900628R02 47 Issued: August 13, 2001 4.5 POWER SPECTRAL DENSITY MEASUREMENT 4.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT The Maximum of Power Spectral Density Measurement is 8dBm. 4.5.2 TEST INSTRUMENTS Description & ManufacturerModel No.Serial No.Calibrated Until ROHDE & SCHWARZ TEST RECEIVER ESMI839379/002Dec. 28, 2001 HP ATTENUATOR8496B3247A18505Cal. on use HP PLOTTER7475A2641V27755N/A NOTE: 1. The measurement uncertainty is less than +/- 2.6dB, which is calculated as per the NAMAS document NIS81. 2. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. FCC ID: M4Y-000325 Report No.: RF900628R02 48 Issued: August 13, 2001 4.5.3 TEST PROCEDURE The transmitter output was connected to the spectrum analyzer through an attenuator, the bandwidth of the fundamental frequency was measured with the spectrum analyzer using 3 kHz RBW and 30 kHz VBW, set sweep time=span/3kHz. The power spectral density was measured and recorded. The sweep time is allowed to be longer than span/3KHz for a full response of the mixer in the spectrum analyzer. 4.5.4 TEST SETUP 4.5.5 EUT OPERATING CONDITIONS Same as 4.3.5 EUT SPECTRUM ANALYZER Attenuator FCC ID: M4Y-000325 Report No.: RF900628R02 49 Issued: August 13, 2001 4.5.6 TEST RESULTS EUT 2.4GHz Wireless LAN Card MODEL XI-325, XI-325B INPUT POWER (SYSTEM) 120Vac, 60 Hz ENVIRONMENTAL CONDITIONS 27 deg. C, 75%RH, 1005 hPa TESTED BY: Gary Chang CHANNEL NUMBER CHANNEL FREQUENCY (MHz ) RF POWER LEVEL IN 3 KHz BW (dBm) MAXIMUM LIMIT (dBm) PASS/FAIL 12412-11.508PASS 62437-11.378PASS 112462-10.518PASS FCC ID: M4Y-000325 Report No.: RF900628R02 50 Issued: August 13, 2001 CH1 FCC ID: M4Y-000325 Report No.: RF900628R02 51 Issued: August 13, 2001 CH6 FCC ID: M4Y-000325 Report No.: RF900628R02 52 Issued: August 13, 2001 CH11 FCC ID: M4Y-000325 Report No.: RF900628R02 53 Issued: August 13, 2001 4.6 BAND EDGES MEASUREMENT 4.6.1 LIMITS OF BAND EDGES MEASUREMENT Below –20dB of the highest emission level of operating band (in 100KHz Resolution Bandwidth). 4.6.2 TEST INSTRUMENTS Description & ManufacturerModel No.Serial No.Calibrated Until ROHDE & SCHWARZ TEST RECEIVER ESMI 848926/005 846839/018 Dec 28, 2001 HP ATTENUATOR8496B3247A18505 Cal. on use HP PLOTTER7475A2641V27755 N/A NOTE: 1. The measurement uncertainty is less than +/- 2.6dB, which is calculated as per the NAMAS document NIS81. 2. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 4.6.3 TEST PROCEDURE The transmitter output was connected to the spectrum analyzer via a low lose cable. Set both RBW and VBW of spectrum analyzer to 100 kHz with suitable frequency span including 100 kHz bandwidth from band edge. The band edges was measured and recorded. FCC ID: M4Y-000325 Report No.: RF900628R02 54 Issued: August 13, 2001 4.6.4 EUT OPERATING CONDITION Same as Item 4.3.5 4.6.5 TEST RESULTS The spectrum plots are attached on the following 2 pages. D2 line indicates the highest level, D1 line indicates the 20dB offset below D2. It shows compliance with the requirement in part 15.247(C). NOTE: The band edge emission plot on the following 4 pages shows 20.0dB delta between carrier maximum power and local maximum emission in restrict band (2.48635GHz). The emission of carrier strength list in the test result of channel 11 at the item 4.2.6 (Page 28) is 97.3dBuV/m, so the maximum field strength in restrict band is 97.3-47.61=49.69 dBuV/m which is under 54 dBuV/m limit. FCC ID: M4Y-000325 Report No.: RF900628R02 55 Issued: August 13, 2001 FCC ID: M4Y-000325 Report No.: RF900628R02 56 Issued: August 13, 2001 FCC ID: M4Y-000325 Report No.: RF900628R02 57 Issued: August 13, 2001 FCC ID: M4Y-000325 Report No.: RF900628R02 58 Issued: August 13, 2001 FCC ID: M4Y-000325 Report No.: RF900628R02 59 Issued: August 13, 2001 4.7 ANTENNA REQUIREMENT 4.7.1 STANDARD APPLICABLE For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And according to FCC 47 CFR Section 15.247 (b), if transmitting antennas of directional gain greater than 6dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6dBi. 4.7.2 ANTENNA CONNECTED CONSTRUCTION The antenna used in this product is printed antenna. There is no antenna connector for model XI-325, and MMCX antenna connector is used for model XI-325B. The maximum Gain of this antenna is only -1dBi. FCC ID: M4Y-000325 Report No.: RF900628R02 60 Issued: August 13, 2001 5 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST FCC ID: M4Y-000325 Report No.: RF900628R02 61 Issued: August 13, 2001 RADIATED EMISSION TEST FCC ID: M4Y-000325 Report No.: RF900628R02 62 Issued: August 13, 2001 6 INFORMATION ON THE TESTING LABORATORIES We, ADT Corp., were founded in 1988 to provide our best service in EMC and Safety consultation. Our laboratories are accredited and approved by the following approval agencies according to ISO/IEC 17025, Guide 25 or EN 45001: USA FCC, NVLAP Germany TUV Rheinland Japan VCCI New Zealand MoC Norway NEMKO R.O.C. BSMI, DGT, CNLA Copies of accreditation certificates of our laboratories obtained from…

Text truncated - open the document above for the full version.