PKW-WCB54GWireless-G CardBus Module

Wireless-G CardBus Module User Manual Rev 0.9 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer- ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is en- couraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to op- erate this equipment. This device complies with Part 15 of the FCC Rules. Operation is sub- ject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunc- ii tion with any other antenna or transmitter. This device is intended only for OEM integrators under the fol- lowing conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still respon- sible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be re- sponsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users (for example access points, routers, wireless ADSL modems, and similar equipment). The final end product must be labeled in a visible area with the following: “Contains TX FCC ID: PKW-WCB54G ”. Manual Information That Must be Included The users manual for end users must include the following in- formation in a prominent location “ IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the an- Preface iii tenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other an- tenna or transmitter. iv Table of contents CHAPTER 1 .................................................................................................... 1 Introduction 1 Features ............................................................................................... 1 What is Wireless LAN? ........................................................................ 2 LAN Modes .......................................................................................... 3 Notes on wireless LAN configuration .................................................. 4 CHAPTER 2 .................................................................................................... 5 Hardware installation 5 Hardware description .......................................................................... 5 Product Outlook ................................................................................. 5 CHAPTER 3 .................................................................................................... 7 Using the Wireless Utility 7 Configuration Utility............................................................................ 7 APPENDIX A ................................................................................................ 10 Specifications ..................................................................................... 10 1 Chapter 1 Introduction Thank you for using the Wireless LAN Module. This high-speed 54Mbps Wireless Module provides you with an innovative wireless networking solution for your embedded system. The module is easy to set up and use. With this innovative wireless technology, you can share files and printers on the network—without inconvenient wires! Now you can carry the LAN in your pocket! This module is designed for 1. Wireless LAN Printer Server 2. Wireless LAN Ethernet Adapter 3. Wireless LAN Access Point 4. Wireless LAN Router / Gateway / Cable Modem 5. Wireless LAN Broadband Router 6. Wireless LAN Presentation Gateway Features • Wire-free access to networked resources from anywhere beyond t…

Text truncated - open the document above for the full version.

FCC ID: PKW-WCB54G ADT No.920206R08A Modular Approval Request Letter Advance Data Technology March 24, 2003 Dear Application Examiner, The Linksys’s Wireless-G CardBus Module, FCC ID: PKW-WCB54G, would like to have your authorization for Limited Module Approval (mobile module) specific to the mobile device such as Wireless LAN Printer Server, Wireless LAN Ethernet Adapter, Wireless LAN Access Point, Wireless LAN Router / Gateway / Cable Modem, Wireless LAN Broadband Router and Wireless LAN Presentation Gateway. The requirements of Public Notice DA00-1407 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.”: The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip ISL3890IK. 3. “The modular transmitter must have its own power supply regulation.” There is a regulator in the DC input port, the part number is ISL6411IR. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a PCMCIA-Mini PCI adapter card. Please see section Photographs of Test Configuration in the test report. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: PKW-WCB54G ADT No.920206R08A 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Dr. Alan Lane Manager of R&TTE Division Advance Data Technology

Page 1 ANNEX PHOTOGRAPHS OF EUT Page 2 Page 3 Page 4

Page 5 Page 6 Page 7

FCC ID: PKW-WCB54G ADT No.: 920206R08A RF EXPOSURE REPORT REPORT NO.: RF920206R08A MODEL NO.: WCB54G ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT: The Linksys Group, Inc. ADDRESS: 17401 Armstrong Ave. Irvine, CA 92614 ISSUED BY: Advance Data Technology Corporation LAB LOCATION: 47 14th Lin, Chiapau Tsun, Linko, Taipei, Taiwan, R.O.C. 0528 ILAC MRA Lab Code: 200102-0 FCC ID: PKW-WCB54G ADT No.: 920206R08A RF Exposure Measurement (Mobile Device) 1. Introduction 2.4GHz frequency band is regarded specially as a dangerous band for its heating harmfulness to the human body. That’s why microwave oven is operating in this frequency band. The manufacturer whose product is working in this frequency band is obligatory to prove the harmfulness of his product. In this document, we try to prove the safety of radiation harmfulness to the human body for our product. The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The Gain of the antenna used in this product is measured in a Fully Anechoic Chamber (FAC), and the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. 2. Classification The antenna of the product, under normal use condition, is at least 20cm away from the body of the user. Warning statement for keeping 20cm separation distance and the prohibition of operating next to a person has been printed on the user’s manual. So, this product is classified as the Mobile Device. 3. RF Exposure Limit According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b). FCC ID: PKW-WCB54G ADT No.: 920206R08A LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) (A)Limits For Occupational / Control Exposures 30-30061.40.1631.06 300-1500......F/3006 1500-100,000......56 (B)Limits For General Population / Uncontrolled Exposure 30-30027.50.0730.230 300-1500......F/150030 1500-100,000......1.030 F = Frequency in MHz 4. Friis Formula Friis transmission formula : Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd is the limit of MPE, 1 mW/cm 2 . If we know the maximum Gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Ref. : David K. Cheng, Field and Wave Electromagnetics, Second Edition, Page 640, Eq. (11-133). 5. EUT Operating condition The software provided by Manufacturer enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. FCC ID: PKW-WCB54G ADT No.: 920206R08A 6. Test Results 6.1 Antenna Gain The maximum Gain measured in Fully Anechoic Chamber is 5dBi or 3.16 (numeric). 6.2 Output Power Into Antenna & RF Exposure Distance : For 802.11b: CHANNEL CHANNEL FREQUENCY (MHz) OUTPUT POWER TO ANTENNA (mW) MINIMUM ALLOWABLE DISTANCE ( r ) FROM SKIN (Centi-Meter) 1241254.203.69 6243756.493.77 11246255.983.75 For 802.11g: CHANNEL CHANNEL FREQUENCY (MHz) OUTPUT POWER TO ANTENNA (mW) MINIMUM ALLOWABLE DISTANCE ( r ) FROM SKIN (Centi-Meter) 1241253.953.68 6243755.593.74 11246255.343.73 The minimum allowable distance is very close to the enclosure of the antenna and is very far away from the human being under normal use condition.

5 5 4 4 3 3 2 2 1 1 DD CC BB AA 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF 68PF 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF 3PF 0.1UF 0.1UF 44MHZ 0.1UF 0.1UF 0.1UF 0.1UF 3PF 0.1UF 0.1UF 0.1UF 10UF 0.1UF 820PF 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF 820PF 0.1UF 0.1UF 0.1UF 0.1UF 62PF 0.1UF 0.1UF 0.1UF AD < 31..0 > AD < 31..0 > PCI < 17.. 0 > 1 2 3 45 6 7 8 A0 A1 A2 GNDSDA SCL WP VCC U8 TPS62005DGS 1 2 3 4 56 7 8 9 10 VIN FC GND PG FBILIM SYNC EN L PGND 12 3 12 CASE 13 2 AC NC 4 1 2 3 VDD GND GND OUT U1 ISL3890IK F19 F17 F18 G17 D19 E19 E18 D20 C19 B16 A19 B17 C16 C17 A15 C15 C12 B9 D11 D13 A9 A8 B11 D10 B7 C6 B8 C7 D8 D5 B6 B4 B2 C5 C3 B5 B3 C4 C11 C13 B13 C14 B14 D14 D9 B12 D15 E17 C10 A1 A5 C9 A12 H17 G19 H18 G20 H19 J17 H20 J18 K18 K17 K19 L20 L19 M19 M20 R4 F4 R18 U16 W17 W14 U10 Y8 W1 U2 N18 P20 G3 D2 A2A4A6A10A13A16A18C20D1E20G1J20K1L18P1R20U1U3Y3A3A7A11A14A17B20C1E1F20H1K20L1M18R1T3Y4U17U19V8W10V11U12W16P18U8 B10B15C8D6D7D12D18E2N17G18H4J3J19L17M2T1T4V1V4W6Y20Y6V9V12V14W19P17T18W7V18 P4 R2 J1 K2 K3 M4 L4 L3 P3 P19 N4 M1 M3 T2 N2 T19 U20 R19 N3 F1 R3 Y9 V10 Y7 W8 Y18 V16 V17 Y19 Y11 W12 Y12 Y13 W13 Y14 Y15 Y16 Y17 V15 W18 N1 P2 W15 W9 U13 E3 K4 J2 H2 J4 H3 G2 L2 F2 G4 F3 Y2 W5 V5 W4 U6 V20 R17 Y5 V7 U7 V6 W11 Y10 PCI_AD0 PCI_AD1 PCI_AD2 PCI_AD3 PCI_AD4 PCI_AD5 PCI_AD6 PCI_AD7 PCI_AD8 PCI_AD9 PCI_AD10 PCI_AD11 PCI_AD12 PCI_AD13 PCI_AD14 PCI_AD15 PCI_AD16 PCI_AD17 PCI_AD18 PCI_AD19 PCI_AD20 PCI_AD21 PCI_AD22 PCI_AD23 PCI_AD24 PCI_AD25 PCI_AD26 PCI_AD27 PCI_AD28 PCI_AD29 PCI_AD30 PCI_AD31 RESET PCI_RST PCI_REQ PCI_INTA PCI_GNT PCI_PME PCI_IRDY PCI_TRDY PCI_SERR PCI_DEVSEL PCI_STOP PCI_PERR PCI_CBE3 PCI_CBE2 PCI_CBE1 PCI_CBE0 PCI_FRAME CLKRUN PCI_CLK PCI_IDSEL PCI_PAR TEST11 TEST10 TEST9 TEST8 TEST7 TEST6 TEST5 TEST4 TEST3 TEST2 TEST1 TEST0 TSTCLK80 TSTCLK44 CLKOUT UARTSIN UARTSOUT COMPPABIAS COMPTX COMPRX COMPIQ COMPIOFF COMPQOFF LFXTALIN LFXTALOUT OSCENABLE CLKIN40 FAAMODE FAA_HRO 3. 3 IO3. 3 IO3. 3 IO3. 3 IO3. 3 IO3. 3 IO3. 3 IO3. 3 IO3. 3 IO3. 3 IO3. 3 IO3. 3 IO3. 3 IO3. 3 IO3. 3 IO3. 3 IO3. 3 IO3. 3 IO3. 3 IO 1. 8V1. 8V1. 8V1. 8V1. 8V1. 8V1. 8V1. 8V1. 8V1. 8V1. 8V1. 8V1. 8V1. 8V1. 8V1. 8V VDDD1 VDDAPLL VDDA1VDDA2VDDA3VDDA4VDDA5VDDA6VDDD0 GNDDGNDDGNDDGNDDGNDDGNDDGNDDGNDDGNDDGNDDGNDDGNDDGNDDGNDDGNDDGNDDGNDDGNDDGNDDGNDDGNDDD1GNDD0GNDA1GNDA3GNDA4GNDA5GNDA6GNDAPLLVSUB1VSUB2 LED0 LED1 FAA_LED SERCLL SERDAT DLL_LD ANTSEL RADIO_PE SYNTH_LE LNA H/L T/R_SW ANTSEL T/R_SW PE1 PE2 FSADPABIAS 2GPABIAS 5GPABIAS PA_PE2G PA_PE5G HB_LB IOFFSET + IOFFSET - QOFFSET + QOFFSET - BB_AGC + BB_AGC - FSADTX FSADRX RXI + RXI - RXQ + RXQ - TXI + TXI - TXQ + TXQ - PA_DET TX_IQ_DET TX_IFAGC SYNTHCLK SYNTHDATA RX_IF_DET FSADOFF FSADIQ GP1-2 GP2-3 GP2-4 GP2-5 GP2-6 GP2-7 GP2-8 GP2-10 GP2-11 GP2-12 GP2-13 TRST TD0 TDI TMS TCK LOOP80 LOOP44 TMSEL3 TMSEL2 TMSEL1 TMSEL0 IREF VREF ISL6411IR U3 1 2 3 4 5678 9 10 11 12 13141516 17 RESET CT SHDN SHDN3 OUT3CC3GND3GND CC2 OUT2 CC1 OUT1 VINVIN FAULTRESET EP J2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 GND CAD0 CAD1 CAD3 CAD5 CAD7 CCBE0# CAD9 CAD11 CAD12 CAD14 CCBE1# CPAR CPERR# CGNT# CINT# VCC VPP1 CCLK CIRDY# CCBE2# CAD 18 CAD20 CAD21 CAD22 CAD23 CAD24 CAD25 CAD26 CAD27 CAD29 RFU CCLKRUN# GND GND CCD1# CAD2 CAD4 CAD6 RFU CAD8 CAD10 CVS1 CAD13 CAD15 CAD16 RFU CBLOCK# CSTOP# CDEVSEL# VCC VPP2 CTRDY# CFRAME# CAD17 CAD19 CVS2 CRST# CSERR# CREQ# CCBE3# CAUDIO CSTSCHG CAD28 CAD30 CAD31 CCD2# GND GND GND GND GND GND GND GND GND

5 5 4 4 3 3 2 2 1 1 DD CC BB AA 100PF no popno pop 27PF no pop no pop no pop no pop no pop 27PF no pop no pop no pop no pop no pop 27PF no popno pop 100PF 27PF 1 2 3 4 5 6 789101112 13 14 15 16 17 18 192021222324 25 GND 5GHZ_BIAS 2GHZ_BIAS GND 2GHZ_RF_IN GND +3.3V+3.3VGND2GHZ_RF_OUT2GHZ_RF_OUTGND GND 2GHZ_DET_OUT GND 5GHZ_RF_OUT 5GHZ_RF_OUT GND 5GHZ_DET_OUT +3.3V+3.3V GND 5GHZ_RFIN GND EP 1 2 3 4 5 6 HIGHFREQ GND LOWFREQ GND COMMPORT GND 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33343536373839404142434445464748 12345678910111213141516 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 LNA_VCC LNA_GND LB_SHIELD LB_LNA_IN + LB_LNA_IN - HB_SHIELD HB_LNA_IN + HB_LNA_IN - HB_SHIELD_2 LB_TX_OUT + LB_TX_OUT - HB_TX_OUT + HB_TX_OUT - TX_GND TX_VCC2 TX_VCC1 TX_DETTX_AGCTX_BB_VCCTX_BB_GNDQLO_VCCQLO_GNDLO_IN +LO_IN -QLO_GND_2REF_INCLKCP_VDDCP_DOCP_GNDSYNTH_GNDSYNTH_VDD BB_OVLDBB_AGC - BB_AGC + BB_GND/RREF I_OFFSET - I_OFFSET + BB_GND/RREF_2 Q_OFFSET - Q_OFFSET + MIXER_GND_2 MIXER_GND MIXER_VCC PE2PE1 HB_LB LNA_H/L LD_RREF PRE_VDD PRE_GND TX_Q - TX_Q+ LE TX_I - TX_I + DATA 1.2V_REF RX_Q - RX_Q + RX_AGC_VCC RX_AGC_GND RX_I - RX_I + EP 1 2 48 1357 OUTIN GNDGNDGNDGND 1 2 4 35 6 78 NC UNBAL BAL NCNC BAL GNDGND 1 2 123 4 5 6 789 10 11 12 13 GNDGND V1 ANT1 GND ANT2 V2GNDGND RX GND TX EP 1 24 35 6 78 NC UNBALBAL NCNC BAL GNDGND IN OUT GND GND GND GND 1 2 3 4 13141516 5678 9 10 11 12 17 BUFF_GND1 OSC - OSC + BUFF_GND2 CORE_GND1 VTUNEVTREF GND BUFF_VCCPEHB_LBCORE_GND2 FILTER_CAP2 FILTER_GND FILTER_CAP1 CORE_VCC EP 12 43 INOUT GNDGND 1 2 4 3 56 IN GND OUT OUT GNDNC 1 2 4 3 56 IN GND OUT OUT GNDNC 1 2 3 4 5 6 HIGHFREQ GND LOWFREQ GND COMMPORT GND

FCC ID: PKW-WCB54G Report No.: RF920206R08A1Issued: March 24, 2003 FCC TEST REPORT REPORT NO.: RF920206R08A MODEL NO.: WCB54G RECEIVED: Feb. 6, 2003 TESTED: Feb. 13 ~ Mar. 19, 2003 APPLICANT: The Linksys Group, Inc. ADDRESS: 17401 Armstrong Ave. Irvine, CA 92614 ISSUED BY: Advance Data Technology Corporation LAB LOCATION: 47 14th Lin, Chiapau Tsun, Linko, Taipei, Taiwan, R.O.C. This test report consists of 73 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, NVLAP or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA Lab Code: 200102-0 FCC ID: PKW-WCB54G Report No.: RF920206R08A2Issued: March 24, 2003 Table of Contents 1CERTIFICATION ........................................................................................... 4 2SUMMARY OF TEST RESULTS................................................................... 5 3GENERAL INFORMATION ........................................................................... 6 3.1GENERAL DESCRIPTION OF EUT.............................................................. 6 3.2DESCRIPTION OF TEST MODES................................................................ 7 3.3GENERAL DESCRIPTION OF APPLIED STANDARDS ............................... 7 3.4DESCRIPTION OF SUPPORT UNITS .......................................................... 8 4TEST TYPES AND RESULTS....................................................................... 9 4.1CONDUCTED EMISSION MEASUREMENT ................................................ 9 4.1.1LIMITS OF CONDUCTED EMISSION MEASUREMENT.............................. 9 4.1.2TEST INSTRUMENTS .................................................................................. 9 4.1.3TEST PROCEDURES................................................................................. 10 4.1.4DEVIATION FROM TEST STANDARD ....................................................... 10 4.1.5TEST SETUP ...............................................................................................11 4.1.6EUT OPERATING CONDITIONS................................................................ 12 4.1.7TEST RESULTS.......................................................................................... 13 4.2RADIATED EMISSION MEASUREMENT ................................................... 19 4.2.1LIMITS OF RADIATED EMISSION MEASUREMENT................................. 19 4.2.2TEST INSTRUMENTS ................................................................................ 20 4.2.3TEST PROCEDURES................................................................................. 21 4.2.4DEVIATION FROM TEST STANDARD ....................................................... 21 4.2.5TEST SETUP .............................................................................................. 22 4.2.6EUT OPERATING CONDITIONS................................................................ 22 4.2.7TEST RESULTS (A) .................................................................................... 23 4.2.8TEST RESULTS (B) .................................................................................... 31 4.36dB BANDWIDTH MEASUREMENT .......................................................... 39 4.3.1LIMITS OF 6dB BANDWIDTH MEASUREMENT ........................................ 39 4.3.2TEST INSTRUMENTS ................................................................................ 39 4.3.3TEST PROCEDURE ................................................................................... 40 4.3.4DEVIATION FROM TEST STANDARD ....................................................... 40 4.3.5TEST SETUP .............................................................................................. 40 4.3.6EUT OPERATING CONDITIONS................................................................ 40 4.3.7TEST RESULTS.......................................................................................... 41 4.4MAXIMUM PEAK OUTPUT POWER .......................................................... 49 4.4.1LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT ........... 49 FCC ID: PKW-WCB54G Report No.: RF920206R08A3Issued: March 24, 2003 4.4.2TEST INSTRUMENTS ................................................................................ 49 4.4.3TEST PROCEDURES................................................................................. 50 4.4.4DEVIATION FROM TEST STANDARD ....................................................... 50 4.4.5TEST SETUP .............................................................................................. 50 4.4.6EUT OPERATING CONDITIONS................................................................ 50 4.4.7TEST RESULTS.......................................................................................... 51 4.5POWER SPECTRAL DENSITY MEASUREMENT...................................... 52 4.5.1LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT ................... 52 4.5.2TEST INSTRUMENTS ................................................................................ 52 4.5.3TEST PROCEDURE ................................................................................... 53 4.5.4DEVIATION FROM TEST STANDARD ....................................................... 53 4.5.5TEST SETUP .............................................................................................. 53 4.5.6EUT OPERATING CONDITIONS................................................................ 53 4.5.7TEST RESULTS.......................................................................................... 54 4.6BAND EDGES MEASUREMENT ................................................................ 62 4.6.1LIMITS OF BAND EDGES MEASUREMENT ............................................. 62 4.6.2TEST INSTRUMENTS ......................…

Text truncated - open the document above for the full version.

FCC ID: PKW-WCB54G Report No.: RF920206R08A69Issued: March 24, 2003 5 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST FCC ID: PKW-WCB54G Report No.: RF920206R08A70Issued: March 24, 2003 FCC ID: PKW-WCB54G Report No.: RF920206R08A71Issued: March 24, 2003 RADIATED EMISSION TEST FCC ID: PKW-WCB54G Report No.: RF920206R08A72Issued: March 24, 2003