PKW-WSB24-2Wireless Signal Booster

WWW. LINKS YS . C O M A. With your Access Point/Router powered off, place the Wireless Signal Booster on top of the Access Point/Router. B. Disconnect the Access Point’s/Router’s a ntennas. C. Connect the Signal Booster Cables from the Access Point’s/Router’s a nten- na ports to the Wireless Si gnal Booster’s cable ports. D. Connect the antennas to the Wireless Signal Booster’s a ntenna ports. E. Connect the appropriate power adapters to both the Access Point/Router and Wireless Signal Booster. F. Now you are ready to use the Wireless Signal Booster in your wireless network. Connecting the Wireless Signal Booster toYour Linksys Access Point/Router QI-WSB24-10/25/02NC BW B Minimum Requirements• One of the f ollowing Linksys products: Wireless Access Point, WAP11Wireless Router, BEFW11S4 Package Contents• One Linksys W ireless Signal Booster • Two Signal Booster Cables• One Power Adapter• One Quick Installation guide Wireless Signal Booster Instant Wireless ® WSB24 The Wireless Signal Booster with Access Point C D E Note: The images in this document show the Wireless Signal Booster being con- nected to an Access Point; the same directions can be followed when connecting theWireless Signal Booster to a wireless Router. wsb24 quick install-1.qxd 2002/12/11 ¤U¤È 01:14 Page 1 COPYRIGHT & TRADEMARKSCopyright c 2002 Linksys, All Rights Reserved. All other trademarks and brandnames are the property of their respective proprietors.LIMITED WARRANTYLinksys guarantees that every Wireless Signal Booster WSB24 is free from physicaldefects in material and workmanship under normal use for one years from the dateof purchase. If the product proves defective during this warranty period, call LinksysCustomer Support in order to obtain a Return Authorization Number. BE SURE TOHAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. RETURNREQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE.When returning a product, mark the Return Authorization Number clearly on the out-side of the package and include a copy of your original proof of purchase. All cus-tomers outside of the United States of America and Canada shall be held responsi-ble for shipping and handling charges.IN NO EVENT SHALL LIN KSYS’ LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DEFECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSE-QUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, ITSACCOMPANYING SOFTWARE, OR ITS DOCUMENTATION. LINKSYS DOES NOTISSUE REFUNDS. WARRANTY DOES NOT COVER NATURAL DISASTERS ORACTS OF NATURE.Linksys makes no warranty or representation, expressed, implied, or statutory, withrespect to its products or the contents use of this documentation and all accompany-ing software, and specially disclaims its quality, performance, merchantability, or fit-ness for any particular purpose. Linksys reserves the right to revise or update itsproducts, software, or documentation without obligation to notify any individual orentity. Please direct all inquiries to :Linksys P.O.Box 18558, Irvine, CA 92623CAUTION : ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED IN THIS MANUAL COULD VOID YOUR AUTHORIZATION TO USETHIS DEVICE. This device should be operated at least 2.0m away from any person FCC STATEMENTThe Wireless Signal Booster WSB24 has been tested and found to comply with thelimits for a class B digital device, pursuant to part 15 of the FCC Rules. These limitsare designed to provide reasonable protection against harmful interference in a resi-dential installation.This equipment generates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interfer-ence to radio communications. However, there is no guarantee that interference willnot occur in a particular installation. If this equipment does cause harmful interfer-ence to radio or television reception, which can be determined by turning the equip-ment off and on, the user is encouraged to try to correct the interference by one ormore of the following measures:—-Reorient or relocate the rece iving antenna. —-Increas e the separation between the equipment and receiver. —-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.—-Con sult the dealer or an experienced radio/TV technician for help. Regulatory information / DisclaimersInstallation and use of this Wireless LAN device must be in strict accordance withthe instructions included in the user documentation provided with the product. Anychanges or modifications (including the antennas) made to this device that are notexpressly approved by the manufa cturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television inter-ference caused by unauthorized modification of this device, or the substitution of theconnecting cables and equipment other than manufacturer specified. It is the respon-sibility of the user to correct any interference caused by such unauthorized modifica-tion, substitution or attachment. Manufacturer and its authorized resellers or distribu-tors will assume no liability for any damage or violation of government regulationsarising from failing to comply with these guidelines.CAUTION: To maintain compli ance with FCC’sRF exposure guidelines, this equipment should be installed and operated with minimum distance20cm between the radiator and your body. Use on the suppliedantenna. Unauthorized antenna, modification, or attachments coulddamage the transmitter and may violate FCC regulations. MPE Statement (Safety Information)Your device contains a low power transmitter. When device is transmitted it sendsout Radio Frequency (RF) signal.Safety InformationIn order to maintain compliance with the FCC RF exposure guidelines, this equip-ment should be installed and operated with minimum distance 20cm between theradiator and your body.Use only with supplied antenna. Unauthorized antenna, modification, or attachmentscould damage the transmitter an…

Text truncated - open the document above for the full version.

- EUT - Adaptor

RD / IE NOTE: 1. 2. SIZE:55.9x25.4mm 3.+-0.5mm Color Black WB1000#LK LBWB1000-RBB-LK120-1 V1.0 03/12//2003 CorelDRAW 9.0 Erica ext. 6104 = 25.4 mm 55.9 mm 1:1 FCC ID:PKW-WSB24-2 The WSB24 is certified by the FCC for use with Linksys WAP11 or BEFW11S4 only. Use of the WSB24 with any other products is strictly prohibited by FCC regulations. Linksys expressly disclaims the implied warranties of merchantability and fitness for a particular purpose for any damages caused by misuses of the WSB24. FOR HOME OR OFFICE USE Tested to Comply With FCC Standards FCC ID:PKW-WSB24-2 The WSB24 is certified by the FCC for use with Linksys WAP11 or BEFW11S4 only. Use of the WSB24 with any other products is strictly prohibited by FCC regulations. Linksys expressly disclaims the implied warranties of merchantability and fitness for a particular purpose for any damages caused by misuses of the WSB24. FOR HOME OR OFFICE USE Tested to Comply With FCC Standards

Spectrum Research & Testing Lab., Inc. No. 101-10, Ling 8, Shan-Tong Li, Chung-Li City, Taoyuan, Taiwan Tel: 886-3-4987684 Fax:: 886-3-4986528 ID LABEL FCC Label Location

- EUT inside - EUT circuit board component and solder side

Spectrum Research & Testing Lab., Inc. No. 101-10, Ling 8, Shan-Tong Li, Chung-Li City, Taoyuan, Taiwan, TEST REPORT Reference No.:A03031104 Report No.:FCCA02120305-01 FCC ID: PKW-WSB24-2 R.O.C. Page:2 of 67 Date:Mar. 11, 2003 TABLE OF CONTENTS 1. DOCUMENT POLICY AND TEST STATEMENT................................................4 1.1 DOCUMENT POLICY.........................................................................................4 1.2 TEST STATEMENT............................................................................................4 2. DESCRIPTION OF EUT AND TEST MODE.......................................................4 2.1 GENERAL DESCRIPTION OF EUT...................................................................4 2.2 DESCRIPTION OF SUPPORT UNIT..................................................................5 2.3 DESCRIPTION OF TEST MODE.......................................................................5 3. DESCRIPTION OF APPLIED STANDARDS.......................................................6 4 . TECHNICAL CHARACTERISTICS TEST..........................................................7 4.1 CONDUCTED EMISSION TEST........................................................................7 4.1.1 LIMIT..................................................................................................................7 4.1.2 TEST EQUIPMENT............................................................................................7 4.1.3 TEST SETUP.....................................................................................................8 4.1.4 TEST PROCEDURE..........................................................................................8 4.1.5 EUT OPERATING CONDITION.........................................................................8 4.1.6 TEST RESULT...................................................................................................9 4.2 RADIATED EMISSION TEST...........................................................................11 4.2.1 LIMIT................................................................................................................11 4.2.2 TEST EQUIPMENT..........................................................................................12 4.2.3 TEST SET-UP..................................................................................................13 4.2.4 TEST PROCEDURE........................................................................................14 4.2.5 EUT OPERATING CONDITION.......................................................................14 4.2.6 TEST RESULT.................................................................................................15 4.3 6DBC BANDWIDTH TEST...............................................................................25 4.3.1 LIMIT................................................................................................................25 4.3.2 TEST EQUIPMENT..........................................................................................25 4.3.3 TEST SET-UP..................................................................................................25 4.3.5 EUT OPERATING CONDITION.......................................................................25 4.3.6 TEST RESULT.................................................................................................26 4.4 PEAK POWER TEST........................................................................................32 4.4.1 LIMIT................................................................................................................32 4.4.2 TEST EQUIPMENT..........................................................................................32 4.4.3 TEST SET-UP..................................................................................................33 4.4.5 EUT OPERATING CONDITION.......................................................................33 4.4.6 TEST RESULT.................................................................................................34 4.5 BAND EDGE TEST...........................................................................................40 4.5.1 LIMIT................................................................................................................40 4.5.2 TEST EQUIPMENT..........................................................................................41 4.5.3 TEST SET-UP..................................................................................................42 4.5.5 EUT OPERATING CONDITION.......................................................................43 4.5.6 TEST RESULT.................................................................................................44 4.5.6 TEST RESULT.................................................................................................47 Spectrum Research & Testing Lab., Inc. No. 101-10, Ling 8, Shan-Tong Li, Chung-Li City, Taoyuan, Taiwan, TEST REPORT Reference No.:A03031104 Report No.:FCCA02120305-01 FCC ID: PKW-WSB24-2 R.O.C. Page:3 of 67 Date:Mar. 11, 2003 4.6 POWER DENSITY TEST................................................................................50 4.6.1 LIMIT................................................................................................................50 4.6.2 TEST EQUIPMENT..........................................................................................50 4.6.3 TEST SET-UP..................................................................................................50 4.6.5 EUT OPERATING CONDITION.......................................................................50 4.6.6 TEST RESULT.................................................................................................51 4.7 RF POWER EXPOSURE EVALUATION TEST...............................................58 4.7.1 LIMIT....................................................................................................…

Text truncated - open the document above for the full version.

- Conducted test (Wireless AP) - Conducted test(Wireless Router) - Radiated test(Wireless AP) - Radiated test(Wireless Router)