POO-WC62Wii Remote Controller

IMPORTANT SAFETY INFORMATION: READ THE FOLLOWING WARNINGS BEFORE YOU OR YOUR CHILD PLAY VIDEO GAMES • Some people (about 1 in 4000) may have seizures or blackouts triggered by light flashes or patterns, such as while watching TV or playing video games, even if they have never had a seizure before. • Anyone who has had a seizure, loss of awareness, or other symptom linked to an epileptic condition should consult a doctor before playing a video game. • Parents should watch when their children play video games. Stop playing and consult a doctor if you or your child have any of the following symptoms: Convulsions Eye or muscle twitching Loss of awareness Altered vision Involuntary movements Disorientation • To reduce the likelihood of a seizure when playing video games: 1. Sit or stand as far from the screen as possible. 2. Play video games on the smallest available television screen. 3. Do not play if you are tired or need sleep. 4. Play in a well-lit room. 5. Take a 10 to 15 minute break every hour. Playing video games can make your muscles, joints, skin or eyes hurt after a few hours. Follow these instructions to avoid problems such as tendinitis, carpal tunnel syndrome, skin irritation or eyestrain: • Avoid excessive play. It is recommended that parents monitor their children for appropriate play. • Take a 10 to 15 minute break every hour, even if you don't think you need it. • If your hands, wrists, arms or eyes become tired or sore while playing, stop and rest them for several hours before playing again. • If you continue to have sore hands, wrists, arms or eyes during or after play, stop playing and see a doctor. WARNING - Seizures WARNING - Repetitive Motion Injuries and Eyestrain IMPORTANT SAFETY INFORMATION: READ THE FOLLOWING WARNINGS BEFORE YOU OR YOUR CHILD PLAY VIDEO GAMES To avoid electric shock when you use this system: • Do not use the Wii during a lightning storm. There may be a risk of electric shock from lighting. • Use only the AC Adapter that comes with your system. • Do not use the AC Adapter if it has damaged, split or broken cords or wires. • Make sure that the AC Adapter cord is fully inserted into the wall outlet or extension cord. • Always carefully disconnect all plugs by pulling on the plug and not on the cord. Make sure the Wii power switch is turned OFF before removing the AC Adapter cord from an outlet. Playing video games can cause motion sickness. If you or your child feel dizzy or nauseous when playing video games with this system, stop playing and rest. Do not drive or engage in other demanding activity until you feel better. The Wii is a Class I laser product. Do not attempt to disassemble the Wii. Refer servicing to qualified personnel only. Caution: Use of controls or adjustments or procedures other than those specified herein may result in hazardous radiation exposure. Specifications: Laser Type: Semiconductor laser Laser wave length: 662nm (typ.) (647nm~687nm) Laser power : Max. 0.9mW Numeric aperture: 0.6 NOTE: This is a latex-free product. WARNING - Electric Shock CAUTION - Motion Sickness CAUTION - Laser Device Components Front ViewBack ViewTOP View BACK View Use to turn the Power ON or OFF. Power Button Power LED RESET SYNCHRO SD Card Slot USB Connector Connector for USB device which has a mark like . Green LED illuminates when power is on. The color and the state(steady light/blinking)of the Power Indicator LED indicate system status. Press to restart the game. Press to resister a Wii Remote to be used with the console. Slot where a SD Card is inserted. Disc Eject Button Press to eject a disc Disc Slot Slot where the disc is inserted Blue light is turned on when disc is inserted. Vent Sensor Bar Connector Connector for Sensor Bar (RVL-014). AV Multi Out Connector for AV Cable (RVL-008) or optional cable (Sold separately). DC Input Connector Connector for DC input of AC Adapter (RVL-002 (USA)). Nintendo Gameube Memory Card Slots Slot where Nintendo GameCube Memory ards are inserted. Upper Slot is Slot-A and Bottom slot is Slot-B. Nintendo GameCube Controller Sockets Socket for connecting Nintendo GameCube controllers (including DK Bongo Controller and Mat Controller). From the right: controller Socket 1,2,3,4. Battery Cover Button Battery (CR2032) is built- in. Open cover only when the battery pack has to be removed for disposal or replacement. Inlet LR6(AA)1.5Vx2 0000000000 FCC ID: X XXXXXXX IC:XXXXX-XXXXX Wii RemoteStrap Use to turn the Power ON or OFF Power Button +Control Pad Speaker Wrist Strap Attachment HOME 1 Button 2 Button Player LED Connector for External Extension device such as Nunchuk and Classic Controller. External Extension Connector -Button (minus(-) button) +Button(plus(+) button) A Button B Button C Button Sensor Bar Plug DC JACK AC Plug Z Button Nunchuk Plug Control Stick Battery cover SYNCHRO Press to register a Wii Remote to be used with the console. For attachment of a wrist strap. Connects to 120V AC wall outlet. AV Multi Out ConnectorPlug Connects to AV Multi Out connector on back of the Wii. Connects to DC input Connector on back of the Wii. Components Front View TOP View View Back View Video(Yellow) Audio Left(White) Audio Right(Red) Setting a Wii Remote Setting a Sensor Bar TV INPUT VIDEO IN AUDIO IN LEFT RIGHT 1. Connecting AV cable Before connecting 2. Connecting Sensor Bar 3. Connecting AC Adapter System set up S Y S T E M O P E R AT I O N Turn your TV on. If the console is connected to your VCR, turn it on also and set the TV to VCR Mode. Chose Disc channel and press A button to confirm. For details on subsequent operations, see the instruction manual of the specific game. Insert the Wii disc or Nintendo GameCube Disk into the Disc slot of the Wii console. Then power goes on automatically. Starting a game 1. 2. 3. Push the Disc Eject Button and remove the Game Disc from the console. REMOVING A GAME DISC VIDEO Wii Game Disc or Nintendo GameCube Disk WARNING - Seizures WARNING - Repetitive Motion Injuries and Eyestr…

Text truncated - open the document above for the full version.

Appendix I sequence the entire LAP (24 bits), 4 LSB’s (4 bits) (Input 1) and the 27 MSB’s of the clock (Input 2) are used. With this input values different mathematical procedures (permutations, additions, XOR-operations) are performed to generate the sequence. This will be done at the beginning of every new transmission. Regarding short transmissions the Bluetooth system has the following behaviors: The first connection between the two devices is established, a hopping sequence was generated. For transmitting the wanted data the complete hopping sequence was not used. The connection ended. The second connection will be established. A new hopping sequence is generated. Due to the fact that the Bluetooth clock has a different value, because the period between the two transmission is longer (and it cannot be shorter) than the minimum resolution of the clock (312.5 μs). The hopping sequence will always differ from the first one. 6 Receiver input bandwidth and behaviors for repeated single or multiple packets: The input bandwidth of the receiver is 1 MHz. In every connection one Bluetooth device is the master and the other one is the slave. The master determines the hopping sequence (see chapter 5). The slave follows this sequence. Both devices shift between RX and TX time slot according to the clock of the master. Additionally the type of connection (e.g. single or multislot packet) is set up at the beginning of the connection. The master adapts its hopping frequency and its TX/RX timing according to the packet type of the connection. Also the slave of the connection will use these settings. Repeating of a packet has no influence on the hopping sequence. The hopping sequence generated by the master of the connection will be followed in any case. That means, a repeated packet will not be send on the same frequency, it is send on the next frequency of the hopping sequence. 7 Dwell time in data mode The dwell time of 0.117s within a 31.6 second period in data mode is independent from the packet type (packet length). The calculation for a 31.6 second period is a follows: Dwell time = time slot length * hop rate / number of hopping channels *31.6s Example for a DH1 packet (with a maximum length of one time slot) Dwell time = 367 μs * 1600 * 1/2 * 1/s / 79 * 31.6s = 0.117s (in a 31.6s period) This is according the Bluetooth Core Specification V 1.0B (+ critical errata) for all Bluetooth devices. There for all Bluetooth devices comply with the FCC dwell time requirement in data mode. This was checked during the Bluetooth Qualification tests. The Dwell time in hybrid mode is measured and stated in the test report.

MITSUMI ELECTRIC CO., LTD. FCC ID: POO-WC62 IC: 4250A-WC62 Page 1 of 3 MITSUMI ELECTRIC CO., LTD. FCC ID: POO-WC62 IC: 4250A-WC62 Page 2 of 3 MITSUMI ELECTRIC CO., LTD. FCC ID: POO-WC62 IC: 4250A-WC62 Page 3 of 3

ID Label Location [ Side view ] top side connector front side side

MITSUMI ELECTRIC CO., LTD. FCC ID: POO-WC62 IC: 4250A-WC62 Page 1 of 5 MITSUMI ELECTRIC CO., LTD. FCC ID: POO-WC62 IC: 4250A-WC62 Page 2 of 5 MITSUMI ELECTRIC CO., LTD. FCC ID: POO-WC62 IC: 4250A-WC62 Page 3 of 5 MITSUMI ELECTRIC CO., LTD. FCC ID: POO-WC62 IC: 4250A-WC62 Page 4 of 5 MITSUMI ELECTRIC CO., LTD. FCC ID: POO-WC62 IC: 4250A-WC62 Page 5 of 5

Report number: Z071C-10017 Page 2 of 37 ZACTA Technology Corp. FCC ID: POO-WC62 FCC 15C Rev.3.0 IC Certification Number: 4250A-WC62 Table of contents Page 1. Summary of Test .................................................................................................................................................................. 4 1.1 Purpose of test .......................................................................................................................................................................... 4 1.2 Standards .................................................................................................................................................................................. 4 1.3 Summary of test results ........................................................................................................................................................... 4 1.4 Deviation from the standard .................................................................................................................................................... 4 1.5 Modification to the EUT by laboratory .................................................................................................................................. 4 2. Equipment description ......................................................................................................................................................... 5 2.1 General Description of equipment .......................................................................................................................................... 5 2.2 EUT information ...................................................................................................................................................................... 5 2.3 Operating channels and frequencies ....................................................................................................................................... 6 2.4 Operating mode ....................................................................................................................................................................... 7 3. Configuration information................................................................................................................................................... 8 3.1 EUT and Peripheral(s) used .................................................................................................................................................... 8 3.2 Cable(s) information ................................................................................................................................................................ 8 3.3 System configuration ............................................................................................................................................................... 8 4. Test Type and Results .......................................................................................................................................................... 9 4.1 20dB Bandwidth / Occupied Bandwidth ................................................................................................................................ 9 4.1.1 Test Procedure [ FCC 15.247(a)(1), IC RSS-210 A8.1(a) ] ........................................................................................... 9 4.1.2 Measurement Setup ........................................................................................................................................................... 9 4.1.3 Limit of Bandwidth at 20 dB below .................................................................................................................................. 9 4.1.4 Measurement Result .......................................................................................................................................................... 9 4.1.5 Trace Data .......................................................................................................................................................................... 9 4.2 Carrier Frequency Separation ............................................................................................................................................... 11 4.2.1 Test Procedure [ FCC 15.247(a)(1), IC RSS-210 A8.1(b) ] ........................................................................................ 11 4.2.2 Measurement Setup ......................................................................................................................................................... 11 4.2.3 Limit of Carrier Frequency Separation ........................................................................................................................... 11 4.2.4 Measurement Result ........................................................................................................................................................ 11 4.2.5 Trace Data ........................................................................................................................................................................ 11 4.3 Number of Hopping Frequencies ........................................................................................................................................ 13 4.3.1 Test Procedure [ FCC 15.247(a)(1)(iii), IC RSS-210 A8.1(d) ] .................................................................................. 13 4.3.2 Measurement Setup ......................................................................................................................................................... 13 4.3.3 Limit of Number of Hopping Frequencies ..................................................................................................................... 13 4.3.4 Measurement Result .........................................................................................…

Text truncated - open the document above for the full version.

MITSUMI ELECTRIC CO., LTD. FCC ID: POO-WC62 IC: 4250A-WC62 Page 1 of 2 System configuration (RF Conducted test) Transmitter Radiated Spurious Emissions (RF Radiated test) MITSUMI ELECTRIC CO., LTD. FCC ID: POO-WC62 IC: 4250A-WC62 Page 2 of 2 Case 1 Case 2 Case 3 Note: Case 1 generates the maximum emission.