PPQ-WN4622R802.11b/g/n 1T1R Wireless Lan USB Module

Ben J. Chen Page 1 12/6/2012 8 8 0 0 2 2 . . 1 1 1 1 n n 2 2 . . 4 4 G G 1 1 T T 1 1 R R W W i i r r e e l l e e s s s s L L A A N N U U S S B B M M o o d d u u l l e e W W N N 4 4 6 6 2 2 2 2 R R User’s Manual Ben J. Chen Page 2 12/6/2012 REGULATORY STATEMENTS FCC Certification The United States Federal Communication Commission (FCC) and the Canadian Department of Communications have established certain rules governing the use of electronic equipment. Part15, Class B This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Ben J. Chen Page 3 12/6/2012 Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. For product available in the USA market, only channel 1~11 can be operated. Selection of other channels is not possible. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the user manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Ben J. Chen Page 4 12/6/2012 Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes: 1. l'appareil ne doit pas produire de brouillage, et 2. l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada. This Category II radio communication device complies with Industry Canada Standard RSS-210. Ce dispositif de radiocommunication de categorie II respecte la norme CNR-210 d'Industrie Canada. Ben J. Chen Page 5 12/6/2012 INTRODUCTION The 802.11b/g/n 1T1R USB WLAN Module is a device that allows you connect your computer to a wireless local area network (LAN). A wireless LAN allows your system to use wireless Radio Frequency (RF) technology to transmit and receive data without physically attaching to the network. The Wireless protocols that come with this product ensure data security and isolation from interference generated by other radio frequencies. This card also allows you to take full advantage of your computer’s mobility with access to real-time information and online services anytime and anywhere. In addition, this device eliminates the bother of pulling cable through walls and under furniture. It even allows you to place your system in locations where cabling is impossible. Modifying and augmenting networks has never been so easy. Wireless Network Options The Peer-to-Peer Network This network installation lets you set a small wireless workgroup easily and quickly. Equipped with wireless PC Cards or wireless PCI, you can share files and printers between each PC and laptop. You can also use one computer as an Internet Server to connect to a wired global network and share files and information with other computers via a wireless LAN. The Access Point Network The network installation allows you to share files, printers, and Internet access much more conveniently. With Wireless LAN Cards, you can connect wireless LAN to a wired global network via an Access Point. Ben J. Chen Page 6…

Text truncated - open the document above for the full version.

RF_160, Issue 03 Declaration of Authorization We Name: Lite-On Technology Corp. Address: 4F, 90, Chien 1 Road, Chung Ho, City: New Taipei City . Country: Taiwan . Declare that: Name Representative of agent: Murphy Wang Agent Company name: A Test Lab Techno Corp. Address: No. 140-1, Changan Street, City: Bade City, Country Taoyuan County 334, Taiwan R.O.C. is authorized to apply for Certification of the following product(s): Product description: 802.11b/g/n 1T1R Wireless Lan USB Module . Type designation:  WN4622R. Trademark: LITE-ON . on our behalf. Date: 12/13/212 City: 4F, 90, Chien 1 Road, Chung Ho,New Taipei City 23585, Taiwan, R.O.C. Name: LITE-ON TECHNOLOGY CORP. / TC Wu Function: Director Signature:  . Notes: (1): Required for FCC application (2): For FCC it must be the Grantee Code “owner” or the authorized agent.

FCC, Request for non-disclosure Date: 16-Jul-10 RF_501, Issue 6 Page 1 of 1 Company Name: LITE-ON TECHNOLOGY CORP. Address: 4F, 90, Chien 1 Road, Chung Ho, 23585, R.O.C. City: New Taipei City Country: Taiwan To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: PPQ-WN4622R Reference number: ###### Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (note 1): Internal Photos User’s Manual Test Set-up Photos External Photos Justification: Planned Release Date STC: (notes 2, 3, 4, 5) Date: 13/12/2012 Name and signature of applicant: TC Wu Director Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY (DoC) Equipment: 802.11b/g/n 1T1R Wireless Lan USB Module Trademark(s) and Model(s): LITE-ON / WN4622R Manufacturer: LITE-ON TECHNOLOGY (Changzhou) CO., LTD FCC ID in case other parts of this equipment are subject to certification: PPQ-WN4622R This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The following test reports are subject to this declaration: Test report number: Issue date: 1212FE14 12/12/2012 The following manufacturer/importer/entity (located in the USA) is responsible for this declaration: Company name: LITE-ON TECHNOLOGY CORP. Name/Title (legal representative): TC Wu /Director Address: 4F, 90, Chien 1 Road, Chung Ho,New Taipei City 23585, Taiwan, R.O.C. Phone: 886-2-2222-6181 Fax: 886-2-2226-6749 E-mail: [email protected] Date: 13/12/2012 Signature: FCC

RF_734_00, Issue 1 Modular Approval Request FCC (per DA 00-1407) FCC ID: PPQ-WN4622R Items to be covered Answer from applicant 1. The modular transmitter must have its own RF shielding. Yes, please refer to EUT photo 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. Yes, module use RT5370 as buffer modulation/ data inputs 3. The modular transmitter must have its own power supply regulation. Yes, module use LDO for 1.2V-3.3V as 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable).. Yes, the antenna is METAL STAMPING ANTENNA. Please refer to external photo. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. Yes, please refer to test photo 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: PPQ-WN4622R” or “Contains FCC ID: PPQ-WN4622R” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. Yes, please refer to label 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. Yes, please refer to user manual 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Yes, please refer RF Exposure test report Note: If compliance with one or more of the numbered requirements, listed above, cannot be demonstrated, it may be possible to obtain a “Limited Modular Approval” (LMA). Name and surname of applicant (or authorized representative): __TC Wu___ Date: __13/12/2012______ Signature: _____ __

1 of 2 External Photos Model Number: WN4622R FCC ID: PPQ-WN4622R IC: 4491A-WN4622R 2 of 2 EUT Photo 1 ) EUT Photo 2 )

16.00mm 13.00mm MM11306990D MAC ID Label WN4622R TPV Rita Huang 2012.11.29 WI-CQES-002 16*13mm S/N:WN4622RXXXXXXXXX MAC ID:XXXXXXXXXXXX FCC ID: PPQ-WN4622R IC: 4491A-WN4622R Made in China 注： MAC ID 一維條碼使用ECC200 1,MAC ID內容顯示為： 2,SN條碼內容顯示為： SN編碼原則： WN4622RXXXXXXXXX WN4622R 客戶：TPV 空白label P/N:50900006563D 16.00mm 13.00mm Model: WN4622R S/N:WN4622RXXXXXXXXX MAC ID:XXXXXXXXXXXX FCC ID: PPQ-WN4622R IC: 4491A-WN4622R Made in China Model: WN4622R

1 of 2 Internal Photos Model Number: WN4622R FCC ID: PPQ-WN4622R IC: 4491A-WN4622R 2 of 2 EUT Photo 1 ) EUT Photo 2 ) ANT

©2012 A Test Lab Techno Corp. Report Number: 1212FS11Page 1 of 6 A Test Lab Techno Corp. Changan Lab：No. 140 -1, Changan Street, Bade City, Taoyuan County, Taiwan R.O.C. Te l：886-3-271-0188 / Fax：886-3-271-0190 MPE Report Test Report No. ： 1212FS11 Applicant ： LITE-ON TECHNOLOGY CORP. Manufacturer ： LITE-ON TECHNOLOGY (Changzhou) CO., LTD Product Type ： 802.11b/g/n 1T1R Wireless Lan USB Module Trade Name ： LITE-ON Model Number ： WN4622R Date of Received ： Dec. 04, 2012 Test Period ： Dec. 04 ~ Dec. 12, 2012 Date of Issued ： Dec. 12, 2012 Test Specification ： 47 CFR § 2.1091 47 CFR §1.1310 ANSI / IEEE Std.C95.1-1992 H46-2/99-237E Location of Test Lab. ： Chang-an Lab. 1. The test operations have to be performed with cautious behavior, the test results are as attached. 2. The test results are under chamber environment of A Test Lab Techno Corp. A Test Lab Techno Corp. does not assume responsibility for any conclusions and generalizations drawn from the test results with regard to other specimens or samples. 3. The measurement report has to be written approval of A Test Lab Techno Corp. It may only be reproduced or published in full. This report shall not be reproduced except in full, without the written approval of A Test Lab Techno Corp. 4. This document may be altered or revised by A Test Lab Techno. Corp. personnel only, and shall be noted in the revision section of the document. Approved By ： Tested By ： (Yung Tan Tsai ) (Bill Hu) Contents 1. Description of Equipment under Test (EUT) ............................................................... 3 2. Human Exposure Assessment..................................................................................... 4 3. RF Output Power........................................................................................................... 5 4. Test Result .....................................................................................................................6 ©2012 A Test Lab Techno Corp. Report Number: 1212FS11Page 2 of 6 ©2012 A Test Lab Techno Corp. Report Number: 1212FS11Page 3 of 6 1. Description of Equipment under Test (EUT) Applicant LITE-ON TECHNOLOGY CORP. Applicant Address 4F, 90, Chien 1 Road, Chung Ho,New Taipei City 23585, Taiwan, R.O.C. Manufacturer LITE-ON TECHNOLOGY (Changzhou) CO., LTD Manufacturer Address A9 Building,No.88 Yanghu Road, Wujin Hi-Tech Industrial Development Zone ,Changzhou City, Jiangsu Province 213100 China Product Type 802.11b/g/n 1T1R Wireless Lan USB Module Trade Name LITE-ON Model Number WN4622R FCC ID PPQ-WN4622R IC 4491A-WN4622R Frequency Range IEEE 802.11b / 802.11g / 802.11n 2.4GHz 20MHz: 2412 – 2462 MHz IEEE 802.11n 2.4GHz 40MHz: 2422 – 2452 MHz Transmit Power IEEE 802.11b: 0.087 W / 19.41 dBm (Conducted Power) IEEE 802.11g: 0.275 W / 24.40 dBm IEEE 802.11n 2.4GHz 20MHz: 0.243 W / 23.86 dBm IEEE 802.11n 2.4GHz 40MHz: 0.166 W / 22.21 dBm Antenna Designation METAL STAMPING ANTENNA Antenna Specification 3.51 dBi Temperature Range -30 ~ +70°C The above equipment was tested by A Test Lab Techno Corp. For compliance with the requirements set forth in 47 CFR § 2.1091 & 47 CFR § 1.1310. The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties 2. Human Exposure Assessment Due to the design and installation of this product, it is not possible to conduct SAR evaluation. This is because client either manufactures or supplies the antenna(s) that will be used in the installation of this product. Therefore, this product will be evaluated as a mobile device per 47 CFR §1.1310 titled “Radiofrequency radiation exposure limits”, generally referred to as MPE limits. In 47 CFR § 2.1091, paragraph (b) defines a mobile device as “a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 cm is normally maintained between the transmitter’s radiating structure(s) and the body of the user or nearby persons. ” This product is intended to be installed into a vehicle such that the unit is physically secured at one location. In the installation guide supplied with the product, Client has made the following statement: “IMPORTANT: To meet the FCC’s RF Exposure Guidelines, the antenna should be installed so there is at least 20 cm of separation between the body of the user and nearby persons and the antenna”. Based on the installation of the transceiver and the antenna, the transmitters radiating structure is more than 20 cm from the user. Thus, this product is a “mobile device” as defined in section § 2.1091 paragraph (b). Exposure evaluation Equation from page 18 of OET Bulletin 65, Edition 97-01 2 4R PG S π = Where S: power density P: power input to the antenna G: power gain of the antenna in the direction of interest relative to an isotropic radiator. R: distance to the center of radiation of the antenna. ©2012 A Test Lab Techno Corp. Report Number: 1212FS11Page 4 of 6 ©2012 A Test Lab Techno Corp. Report Number: 1212FS11Page 5 of 6 3. RF Output Power Conducted power (dBm) Band Date Rate Frequency (MHz) Average Peak Worst Case 2412 16.52 19.23 □ 2437 16.50 19.10 □ IEEE 802.11b 1 M 2462 16.83 19.41 ■ 2412 14.60 24.36 □ 2437 14.08 23.62 □ IEEE 802.11g 6 M 2462 14.49 24.40 ■ 2412 14.32 23.86 ■ 2437 14.47 23.55 □ IEEE 802.11n 2.4GHz_20MHz 6.5 M 2462 14.21 23.84 □ 2422 12.53 22.21 ■ 2437 12.37 22.20 □ IEEE 802.11n 2.4GHz_40MHz 13.5 M 2452 12.16 22.01 □ ©2012 A Test Lab Techno Corp. Report Number: 1212FS11Page 6 of 6 4. Test Result Band Data Rate Frequency (MHz) Limit (mw/cm 2 ) Distance (cm) [R] Power (dBm) [P] ANT Gain (dBi) [G] [P]+ [G] (W) [TP] Power Density [S] (mw/cm 2 ) Min. distance (cm) 2412 1.000 20 19.23 3.51 0.188 0.023 20cm 2437 1.000 20 19.10 3.51 0.182 0.022 20cm IEEE 802.11b 1 M 2462 1.000 20 19.41 3.51 0.196 0.024 20cm 2412 1.000 20 24.36 3.51 0.612 0.0…

Text truncated - open the document above for the full version.

A Test Lab Techno Corp. Report Number: 1212FR14 1 of 70 FCC 47 CFR PART 15 SUBPART C Product Type ： 802.11b/g/n 1T1R Wireless Lan USB Module Applicant ： LITE-ON TECHNOLOGY CORP. Address ： 4F, 90, Chien 1 Road, Chung Ho,New Taipei City 23585, Taiwan, R.O.C. Trade Name ： LITE-ON Model Number ： WN4622R Test Specification ： FCC 47 CFR PART 15 SUBPART C: Oct., 2011 Canada RSS-210 ISSUE 8: Dec., 2010 Canada RSS-Gen ISSUE 3: Dec., 2010 ANSI C63.4-2009 Receive Date ： Dec. 04, 2012 Test Period ： Dec. 04 ~ Dec. 09, 2012 Issue Date ： Dec. 12, 2012 Issue by A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, Taoyuan County 334, Taiwan R.O.C. Te l：+886-3-2710188 / Fax：+886-3-2710190 T aiwan Accreditation Foundation accreditation number: 1330 Note: This report shall not be reproduced except in full, without the written approval of A Test Lab Techno Corp. This document may be altered or revised by A Test Lab Techno Corp. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, or any government agencies. The test results in the report only apply to the tested sample. Revision History Rev. Issue Date Revisions Revised By 00 Dec. 12, 2012 Initial Issue A Test Lab Techno Corp. Report Number: 1212FR14 2 of 70 A Test Lab Techno Corp. Report Number: 1212FR14 3 of 70 Verification of Compliance Issued Date: 12/02/2011 Product Type : 802.11b/g/n 1T1R Wireless Lan USB Module Applicant : LITE-ON TECHNOLOGY CORP. Address : 4F, 90, Chien 1 Road, Chung Ho,New Taipei City 23585, Taiwan, R.O.C. Trade Name : LITE-ON Model Number : WN4622R FCC ID : PPQ-WN4622R IC : 4491A-WN4622R EUT Rated Voltage : DC 3.3V Test Voltage : 120 Vac / 60 Hz Applicable Standard : FCC 47 CFR PART 15 SUBPART C: Oct., 2011 Canada RSS-210 ISSUE 8: Dec., 2010 Canada RSS-Gen ISSUE 3: Dec., 2010 ANSI C63.4-2009 Test Result : Complied Performing Lab. : A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, Taoyuan County 334, Taiwan R.O.C. Te l：+886-3-2710188 / Fax：+886-3-2710190 T aiwan Accreditation Foundation accreditation number: 1330 http://www.atl-lab.com.tw/e-index.htm The above equipment was tested by A Test Lab Techno Corp. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2009 and the energy emitted by the sample tested as described in this report is in compliance with the requirements of FCC Rules Part 15.207, 15.209, 15.247 . The test results of this report relate only to the tested sample identified in this report. Approved By ： Reviewed By ： (Manager) (Murphy Wang) (Testing Engineer) (Fly Lu) TABLE OF CONTENTS 1 General Information ....................................................................................................................................... 6 2 EUT Description ............................................................................................................................................. 7 3 Test Methodology .......................................................................................................................................... 8 3.1. Mode of Operation.................................................................................................................................. 8 3.2. EUT Exercise Software.......................................................................................................................... 8 3.3. Configuration of Test System Details ..................................................................................................... 9 3.4. Test Site Environment .......................................................................................................................... 10 4 Conducted Emission Measurement ........................................................................................................... 11 4.1. Limit .......................................................................................................................................................11 4.2. Test Instruments ....................................................................................................................................11 4.3. Test Setup..............................................................................................................................................11 4.4. Test Procedure ..................................................................................................................................... 12 4.5. Test Result............................................................................................................................................ 13 5 Radiated Emission Measurement............................................................................................................... 15 5.1. Limit ...................................................................................................................................................... 15 5.2. Test Instruments ................................................................................................................................... 15 5.3. Setup .................................................................................................................................................... 16 5.4. Test Procedure ..................................................................................................................................... 17 5.5. Test Result............................................................................................................................................ 19 6 Maximum Conducted Output Power Measurement.................................................................................. 27 6.1. Limit ...................................................................................................................................................... 27 6.2.…

Text truncated - open the document above for the full version.

Part 15C / RSS-210 Test Setup Photographs Conducted Emissions Test Configuration: Front View Rear View A Test Lab Techno Corp. Report Number: 1212FR14 1 of 4 Radiated Emissions Test Configuration: Below 1GHz _ Front View Below 1GHz _ Rear View A Test Lab Techno Corp. Report Number: 1212FR14 2 of 4 Above 1GHz _ Front View Above 1GHz _ Rear View A Test Lab Techno Corp. Report Number: 1212FR14 3 of 4 Close View A Test Lab Techno Corp. Report Number: 1212FR14 4 of 4