PPQ-WN6301MH802.11b/g, 2.4G WIRELESS LAN SDIO HALF SIZE MINI CARD

Ben J. Chen Page 1 10/19/2010 8 8 0 0 2 2 . . 1 1 1 1 b b / / g g , , 2 2 . . 4 4 G G W W i i r r e e l l e e s s s s L L A A N N S S D D I I O O H H a a l l f f S S i i z z e e M M i i n n i i C C a a r r d d W W N N 6 6 3 3 0 0 1 1 M M H H U U s s e e r r ’ ’ s s M M a a n n u u a a l l Ben J. Chen Page 2 10/19/2010 REGULATORY STATEMENTS FCC Certification The United States Federal Communication Commission (FCC) and the Canadian Department of Communications have established certain rules governing the use of electronic equipment. Part15, Class B This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Ben J. Chen Page 3 10/19/2010 Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. For product available in the USA market, only channel 1~11 can be operated. Selection of other channels is not possible. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the user manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Ben J. Chen Page 4 10/19/2010 This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B conforme á la norme NMB-003 du Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p) is not more than that permitted for successful communication. Ben J. Chen Page 5 10/19/2010 INTRODUCTION The Marvell sd8686 Wirless LAN SDIO Adapter is a device that allows you connect your computer to a wireless local area network (LAN). A wireless LAN allows your system to use wireless Radio Frequency (RF) technology to transmit and receive data without physically attaching to the network. The Wireless protocols that come with this product ensure data security and isolation from interference generated by other radio frequencies. This card also allows you to take full advantage of your computer’s mobility with access to real-time information and online services anytime and anywhere. In addition, this device eliminates the bother of pulling cable through walls and under furniture. It even allows you to place your system in locations where cabling is impossible. Modifying and augmenting networks has never been so easy. Wireless Network Options The Peer-to-Peer Network This network installation lets you set a small wireless workgroup easily and quickly. Equipped with wireless PC Cards or wireless PCI, you can share files and printers between each PC and laptop. You can also use one computer as an Internet Server to connect to a wired global network and share files and information with other computers via a wireless LAN. Ben J. Chen Page 6 10/19/2010 The Access P…

Text truncated - open the document above for the full version.

Lite-On Technology Corp. FCC ID.: PPQ-WN6301MH 4F,90,Chien 1 Road,Chung-Ho,Taipei Hsien 235,Taiwan,R.O.C..Tel : 886-2-2222-6181 Federal Communications Commission Oct. 28, 2010 Authorization and Evaluation Division ATTESTATION FCC ID: PPQ-WN6301MH Product: 802.11 b/g, 2.4G Wireless LAN SDIO Half Size Mini Card Model: WN6301MH We don't provide any controls or software to allow operation outside the USA frequency band when we sell this product in USA. Sincerely, ------------------------------------------------------- ML WU / Manager Lite-On Technology Corp.

Lite-On Technology Corp. 4F, 90 ,Chien 1 Road,Chung-Ho,Taipei Hsien 235,Taiwan,R.O.C. TEL No: 886-2-2222-6181 FAX No.: 886-2-2226-6749 Letter of Authorization Date: 2010/11/04 To Whom it may concern I Mr. TC WU, hereby authorize Mr. ML WU, Technical Service Section to take over the certification of below products, he(she) will be designated to act on behalf of me to do all the process related to certification. Product: FCC ID：PPQ-WN6301MH Model name：802.11 b/g, 2.4G Wireless LAN SDIO Half Size Mini Card Model NO：WN6301MH Thank you. Sincerely Yours, _______________________ Name：Mr. TC WU Title Dep. ：Director Company name：Lite-On Technology Corp.

Lite-On Technology Corp. FCC ID.: PPQ-WN6301MH 4F,90,Chien 1 Road,Chung-Ho,Taipei Hsien 235,Taiwan,R.O.C. Tel : 886-2-2222-6181 Lite-On Technology Corp. 4F,90,Chien 1 Road,Chung-Ho,Taipei Hsien 235,Taiwan,R.O.C. Tel : 886-2-2222-6181 Fax: 886-2-2226-6749 Federal Communications Commission Oct. 28, 2010 Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant Hereby requests confidential treatment of information accompanying this Application As outlined below: Schematics: (WN6301MH) Schem Block Diagram: (WN6301MH) BlkDia The above materials contain trade secrets and proprietary information not customarily Released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, ------------------------------------------------------- ML WU / Manager Lite-On Technology Corp.

Lite-On Technology Corp. FCC ID.: PPQ-WN6301MH 4F,90,Chien 1 Road,Chung-Ho,Taipei Hsien 235,Taiwan,R.O.C.Tel : 886-2-2222-6181 Lite-On Technology Corp. 4F,90,Chien 1 Road,Chung-Ho,Taipei Hsien 235,Taiwan,R.O.C. Tel : 886-2-2222-6181 Fax: 886-2-2226-6749 Gentlemen: Regarding to the Pubic Notice DA 00-1407 pertaining to PART 15 UNLICENSED MODULAR TRANSMITTER APPROVAL, Lite-On Technology Corp..would like to request modular approval for the submission FCC ID: PPQ-WN6301MH. Lite-On Technology Corp.. confirms that the product complies with numbered requirements identified below: 1. The modular transmitter have its own RF shielding(Please see the internal photo). 2. The modular transmitter have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over- modulation(Please see the schematic EEPROM “AT25080B-XHL-T TSSOP 8P” in page1). 3. The modular transmitter have its own power supply regulation(Please see the schematic regulation chip“RT9013-18PB in page1). 4. The modular transmitter complies with the antenna requirements of Section 15.203 and 15.204(c). 5. The modular transmitter is tested in a stand-alone configuration (Please see the test photo). 6. The modular transmitter is labeled with its own FCC ID number(Please see the label sample). 7. The modular transmitter complies with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements(Please see the Uesr’s manual). 8. The modular transmitter complies with any applicable RF exposure requirements. Sincerely, ------------------------------------------------------- ML WU / Manager Lite-On Technology Corp.

RF_160, Issue 02 Lite-On Technology Corp. Declaration of Authorization We Name: Lite-On Technology Corp. Address: 4F, 90 ,Chien 1 Road,Chung-Ho,Taipei Hsien 235,Taiwan,R.O.C. City: Taipei  . Country: Taiwan  .  . Declare that: Name Representative of agent: Gene Chang (1) Agent Company name: QuieTek Corp. Address: Fl.2, No.345, Xin-hu 2 nd Rd., Nei-hu District City: Taipei Country Taiwan is authorized to apply for Certification of the following product(s): Product description: 802.11 b/g, 2.4G Wireless LAN SDIO Half Size Mini Card Type designation: WN6301MH  Trademark: LITE-ON  . on our behalf. Date:  2010/10/27  . City:  Taipei  Name:  ML WU  (2) Function:  Manager  Signature:  . Notes: (1): Required for FCC application (2): For FCC it must be the Grantee Code “owner” or the authorized agent.

Lite-On Technology Corp. 4F, 90 ,Chien 1 Road,Chung-Ho,Taipei Hsien 235,Taiwan,R.O.C. Tel No: 886-2-2222-6181 Fax No.: 886-2-2226-6749 Attestation for FCC Declaration of Conformity FCC ID: PPQ-WN6301MH Data: Oct. 28, 2010 Please be notified that we, the undersigned, Lite-On Technology Corp. declares that the product which bears the above FCC ID is also compliant with the FCC requirements for DoC. The test report number supporting the DoC is DOCTR0001 (10A237R-RFUSP24V02 ). Testing in regards to this report was done by QuieTek Corporation, located at 2F, No.345, Xinhu 2nd Rd., Neihu District, Taipei City 114,Taiwan, R.O.C. which has been accredited in accordance to all of the requirements of 47CFR 2.948 (d) and (e) of the FCC rules and KDB349827. Sincerely, ML WU / Manager Lite-On Technology Corp. Tel: 886-2-2222-6181 Fax: 886-2-2226-6749 Email: [email protected]

Report No.: 10A237R-RFUSP42V01 Page : 1 of 4 Attachment 2 : EUT Detailed Photographs (1) EUT Photo (2) EUT Photo

Lite-On Technology Corp. FCC ID.: PPQ-WN6301MH 4F,90,Chien 1 Road,Chung-Ho,Taipei Hsien 235,Taiwan,R.O.C..Tel : 886-2-2222-6181 FCC ID Label The FCC ID Label will be placed on the equipment as shown in the photograph below.

Lite-On Technology Corp. FCC ID.: PPQ-WN6301MH 4F,90,Chien 1 Road,Chung-Ho,Taipei Hsien 235,Taiwan,R.O.C..Tel : 886-2-2222-6181 FCC ID Label The FCC ID Label will be placed on the equipment as shown in the photograph below.

Report No.: 10A237R-RFUSP42V01 Page : 2 of 4 (3) EUT Photo (4) EUT Photo Report No.: 10A237R-RFUSP42V01 Page : 3 of 4 (5) EUT Photo (6) EUT Photo Report No.: 10A237R-RFUSP42V01 Page : 4 of 4 (7) EUT Photo (Test Fixture) (8) EUT Photo EUT

Report No. 10A237R-RFUSP42V01 Page : 7 of 64 1.2. Operational Description The EUT is an 802.11 b/g, 2.4G Wireless LAN SDIO Half Size Mini Card with 11 channels. This device provided four kinds of transmitting speed 1, 2, 5.5 and 11Mbps and the device of RF carrier is DBPSK, DQPSK and CCK (IEEE 802.11b). The device provided of eight kinds of transmitting speed 6, 9, 12, 18, 24, 36, 48 and 54Mbps the device of RF carrier is BPSK, QPSK, 16QAM and 64QAM (IEEE 802.11g). This 802.11 b/g, 2.4G Wireless LAN SDIO Half Size Mini Card, compliant with IEEE 802.11b and IEEE 802.11g, is a high-efficiency Wireless LAN adapter. It allows your computer to connect to a wireless network and to share resources, such as files or printers without being bound to the network wires. Operation in 2.4GHz Direst Sequence Spread Spectrum (DSSS) and Orthogonal Frequency Division Multiplexing (OFDM) radio transmission, the 802.11 b/g, 2.4G Wireless LAN SDIO Half Size Mini Card Wired Equivalent Protection (WEP) algorithm is used. In addition, its standard compliance ensures that it can communicate with any IEEE 802.11b and IEEE 802.11g network.

Report No. 10A237R-RFUSP42V01 Page: 1 of 4 Version: 1.0 RF Exposure Evaluation declaration Product Name : 802.11 b/g, 2.4G Wireless LAN SDIO Half Size Mini Card Model No. : WN6301MH FCC ID : PPQ-WN6301MH Applicant : Lite-On Technology Corp. Address : 4F,90,Chien 1 Road,Chung-Ho,Taipei Hsien 235,Taiwan,R.O.C. Date of Receipt : Oct. 14, 2010 Date of Declaration : Oct. 22, 2010 Report No. : 10A237R-RFUSP42V01 The declaration results relate only to the samples calculated. The declaration shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Report No. 10A237R-RFUSP42V01 Page: 2 of 4 Version: 1.0 1. RF Exposure Evaluation 1.1. Limits According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (Minutes) (A) Limits for Occupational/ Control Exposures 300-1500 -- -- F/300 6 1500-100,000 -- -- 5 6 (B) Limits for General Population/ Uncontrolled Exposures 300-1500 -- -- F/1500 6 1500-100,000 -- -- 1 30 F= Frequency in MHz Friis Formula Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. 1.2. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. The temperature and related humidity: 18°Cand 78％ RH. Report No. 10A237R-RFUSP42V01 Page: 3 of 4 Version: 1.0 1.3. Test Result of RF Exposure Evaluation Product : 802.11 b/g, 2.4G Wireless LAN SDIO Half Size Mini Card Test Item : RF Exposure Evaluation Test Site : No.3 OATS External Antenna Gain Antenna Gain: The maximum Gain measured in fully anechoic chamber is 3.41 dBi in logarithm scale. 802.11b Output Power Into Antenna & RF Exposure Evaluation Distance (3.41dBi): Channel Frequency (MHz) Output Power to Antenna (mW) Power Density at R = 20 cm (mW/cm2) 1 2412.00 57.5440 0.025103 6 2437.00 48.6407 0.021219 11 2462.00 49.4311 0.021564 802.11g Output Power Into Antenna & RF Exposure Evaluation Distance (3.41dBi): Channel Frequency (MHz) Output Power to Antenna (mW) Power Density at R = 20 cm (mW/cm2) 1 2412.00 90.3649 0.039421 6 2437.00 128.8250 0.056199 11 2462.00 117.7606 0.051372 The distance r (4 th column) calculated from the Fries transmission formula is far shorter than 20 cm separation requirement.

Report No. 10A237R-RFUSP42V01 Page : 1 of 63 Test Report Product Name 802.11 b/g, 2.4G Wireless LAN SDIO Half Size Mini Card Model No WN6301MH FCC ID. PPQ-WN6301MH Applicant Lite-On Technology Corp. Address 4F,90,Chien 1 Road,Chung-Ho,Taipei Hsien 235,Taiwan,R.O.C. Date of Receipt Oct. 14, 2010 Issue Date Oct. 22, 2010 Report No. 10A237R-RFUSP42V01 Report Version V1.0 The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Report No. 10A237R-RFUSP42V01 Page : 2 of 63 Test Report Certification Issue Date: Oct. 22, 2010 Report No.: 10A237R-RFUSP42V01 Product Name 802.11 b/g, 2.4G Wireless LAN SDIO Half Size Mini Card Applicant Lite-On Technology Corp. Address 4F,90,Chien 1 Road,Chung-Ho,Taipei Hsien 235,Taiwan,R.O.C. Manufacturer DONG GUAN G-COM COMPUTER CO., LTD. Model No. WN6301MH EUT Rated Voltage DC 3.3V EUT Test Voltage AC 120V/60Hz Trade Name LITE-ON Applicable Standard FCC CFR Title 47 Part 15 Subpart C: 2009 ANSI C63.4: 2003 Test Result Complied The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Documented By : ( Senior Adm. Specialist / Genie Chang ) Tested By : ( Engineer / Joe Guo ) Approved By : ( Manager / Vincent Lin) Accredited by NIST (NVLAP) NVLAP Lab Code: 200533-0 Report No. 10A237R-RFUSP42V01 Page : 3 of 63 TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION .....................................................................................................5 1.1. EUT Description............................................................................................................................5 1.2. Operational Description ................................................................................................................7 1.3. Tested System Details....................................................................................................................8 1.4. Configuration of Tested System ....................................................................................................8 1.5. EUT Exercise Software .................................................................................................................8 1.6. Test Facility ...................................................................................................................................9 2. Conducted Emission..................................................................................................................10 2.1. Test Equipment............................................................................................................................10 2.2. Test Setup ....................................................................................................................................10 2.3. Limits ..........................................................................................................................................11 2.4. Test Procedure .............................................................................................................................11 2.5. Uncertainty ..................................................................................................................................11 2.6. Test Result of Conducted Emission.............................................................................................12 3. Peak Power Output ...................................................................................................................14 3.1. Test Equipment............................................................................................................................14 3.2. Test Setup ....................................................................................................................................14 3.3. Limits ..........................................................................................................................................14 3.4. Test Procedure .............................................................................................................................14 3.5. Uncertainty ..................................................................................................................................14 3.6. Test Result of Peak Power Output...............................................................................................15 4. Radiated Emission .....................................................................................................................17 4.1. Test Equipment............................................................................................................................17 4.2. Test Setup ....................................................................................................................................18 4.3. Limits ..........................................................................................................................................19 4.4. Test Procedure .............................................................................................................................20 4.5. Uncertainty ..................................................................................................................................20 4.6. Test Result of Radiated Emission................................................................................................21 5. RF antenna conducted test........................................................................................................29 5.1. Test Equipment.............................................................................................…

Text truncated - open the document above for the full version.

Report No.: 10A237R-RFUSP42V01 Page : 1 of 3 Attachment 1: EUT Test Setup Photographs Front View of Conducted Test Back View of Conducted Test Report No.: 10A237R-RFUSP42V01 Page : 2 of 3 Front View of Radiated Test Back View of Radiated Test Report No.: 10A237R-RFUSP42V01 Page : 3 of 3 Front View of Radiated Test (Horn) Back View of Radiated Test (Horn)