PQRFXE2000-DGWireless LAN Adapter

1 FXE2000-DG IEEE802.11n/a/b/g Wireless LAN Access Point Board FXE2000-DG Setup Guide CONTEC CO.,LTD. The FXE2000-DG is a wireless LAN board that conforms to IEEE 802.11n/a/b/g standards of various countries and features a wide input power supply (5 to 30 VDC) and can be configured either as an access point or station. Packing List - Main unit (FXE2000-DG)...1 - Setup Guide...1 How to Obtain Service For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please obtain a Return Merchandise Authorization number (RMA) from the CONTEC group office where you purchased before returning any product. *No product will be accepted by CONTEC group without the RMA number. This device sold for OEM vendor only. Default setting This product is set up via a network using a Web browser. Connect this product to the PC with a LAN cable using the wired LAN connection and then access the default IP address in a web browser. This product's default settings are shown in the table to the right. Setting Item Default setting IP Address 192.168.0.1 Subnet Mask 255.255.255.0 ESSID LocalGroup Security Disable Username admin Password pass Component Locations (1) LAN port (2) Power connector (3) DC JACK (4) INIT connector (5) DIP Switches (6) DIP LED LED display LED name Status Indicator POWER ON Indicates that the device is operating. Flashing Indicates that the device is being started (This device turned on) OFF Indicates that the device is power off. LAN ON Indicates that a wired LAN has been connected. Flashing Indicates that the product is transmitting/receiving data to/from the connected terminal through wired LAN. OFF Indicates that a wired LAN not logged-in. WLAN ON Indicates that the device has been connected. Flashing Indicates data is being transmitted to or received from the device connected through wireless LAN. OFF Indicates that the device has been no connected. POWER/ LAN/ WLAN Flashing (simultaneously) Indicates that firmware has been reprogrammed. *1 POWER/LAN Blinking twice / On DHCP error *1 Not include LogFile DIP switches INIT connector No. Name Operation / function No. Name Operation / function 1 INIT Turning on this switch flashes the POWER, WLAN LEDs.If the switch is turned off before the LEDs change their status from flashing to ON (about 3 seconds), all the settings are restored to the default settings after the product is started next time. Reboot the product after the LEDs stop flashing. *1 1 INIT Short the INIT signal with the GND so that the POWER, WLAN, and LAN LEDs will flash. Then if you open the INIT signal before the LEDs turn on (approx. 3 seconds), the settings are restored to the default settings the next time the product is started. 2 - 2 GND GND Pin heder (JP2) LAN connector No. Name Operation / function No. Name Operation / function 1 LAN port 4pin The INIT (initialization) signal can be connected to via pin 4 on the LAN port by shorting pin 1 and pin 2. 1 TX+ Transmit (+) 2 TX- Transmit (-) 2 INIT 3 RX+ Receive (+) 3 LAN port 5pin The GND can be connected to via pin 5 on the LAN port by shorting pin 3 and pin 4. 4 INIT/NC Short the INIT signal with the GND so that the POWER, WLAN, and LAN LEDs will flash. Then if you open the INIT signal before the LEDs turn on (approx. 3 seconds), the settings are restored to the default settings the next time the product is started.*1 * Usable when JP2 No. 1 and No. 2 are connected. 4 GND 5 LAN port 7pin The power supply line can be connected to via pin 7 on the LAN port by shorting pin 5 and pin 6. 6 24VDC 7 LAN port 8pin The GND can be connected to via pin 8 on the LAN port by shorting pin 7 and pin 8. 5 GND GND 6 RX- Receive (-) 8 GND 7 24VDC Power Supply 8 GND GND *1 Usable when JP2 No. 1 and No. 2 are connected. When initializing the product by turning the INIT signal on and off, the LEDs will continue flashing for a short time after the signal is turned off. This indicates the internal memory files are being deleted. If the power is turned off while the LEDs are flashing, the internal memory files may be damaged and the product may no longer be able to start properly. Always restart the product after the LEDs stop flashing. For PoE wire route only in the same building. CAUTION When supplying power via the LAN connector, do not use a combination of power supplied from the power connector and the AC adapter. Power Supply Using the DC JACK The power plug to be used must conform to EIAJ voltage classification 2. CAUTION When supplying power via the LAN connector, do not use a combination of power supplied from the power connector and the AC adapter. Using the Power connector The power connector in Figure 1 can be used to supply power from an external source. Use the following power cable or its equivalent. CAUTION When supplying power from the power connector, do not use a combination of power supplied via the LAN connector and the AC adapter. Figure 1 Power connector Housing: JST S02B-PASK-2(LF)(SN) Cable: AWG28-16(equivalent to it) Pin No. Nome Operation / function 1 Vi+ 5-30VDC±5%) 2 Vi- GND When supplying the LAN cable power CAUTION - Create the power cable correctly as specified. Using the power cable with the housing pins assigned wrong numbers may result in device faults or accidents. - The input voltage range of this product is from 5 to 24 VDC ±5%. Supply power outside that range may result in device faults or accidents. - Use the power supply whose supply voltage rises to at least 4.75VDC within the input voltage range within 10ms. Using a power supply which does not satisfy this condition may result in device faults or accidents. - Input voltage range: 5 to 30 VDC ± 5%. Use a power supply that rises to 4.75 VDC or higher in the input voltage range within 10 ms. There is a risk of damage to the device or accident if a power supply outside this range is used. Installation Read and understand the following precautions before installation : - Leaving a metal object in the vicinity of 30mm …

Text truncated - open the document above for the full version.

Report No.: 140128E04 Page 1 CONSTRUCTION PHOTOS OF EUT Report No.: 140128E04 Page 2 Report No.: 140128E04 Page 3 Report No.: 140128E04 Page 4 Report No.: 140128E04 Page 5

(Fig.1) FCC ID: PQRFXE2000-DG PROPOSED FCC ID LABEL AND LOCATION The label will be permanently affixed at a conspicuous location on the device.

Report No.: 140128E04 Page 1 CONSTRUCTION PHOTOS OF EUT

Report No.: SA140128E04 1 of 8 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA140128E04 MODEL NO.: FXE2000-DG FCC ID: PQRFXE2000-DG RECEIVED: Jan. 28, 2014 TESTED: Feb. 13 to 14, 2014 ISSUED: Apr. 01, 2014 APPLICANT: Contec Co., Ltd. ADDRESS: 3-9-31, Himesato, Nishiyodogawa-ku Osaka Japan 555-0025 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: SA140128E04 2 of 8 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD .................................................................................... 3 1. CERTIFICATION ...................................................................................................... 4 2. RF EXPOSURE LIMIT .............................................................................................. 5 3. MPE CALCULATION FORMULA ............................................................................. 5 4. CLASSIFICATION .................................................................................................... 5 5. ANTENNA GAIN....................................................................................................... 6 6. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ........................... 7 Report No.: SA140128E04 3 of 8 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA140128E04 Original release Apr. 01, 2014 Report No.: SA140128E04 4 of 8 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT: Wireless LAN Adapter BRAND NAME: CONTEC MODEL NO.: FXE2000-DG TEST SAMPLE: ENGINEERING SAMPLE APPLICANT: Contec Co., Ltd. TESTED DATE: Feb. 13 to 14, 2014 STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: FXE2000-DG) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: Apr. 01, 2014 ( Phoenix Huang, Specialist ) APPROVED BY : , DATE: Apr. 01, 2014 ( May Chen, Manager ) Report No.: SA140128E04 5 of 8 Report Format Version 5.0.0 2. RF EXPOSURE LIMIT LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 3. MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 4. CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA140128E04 6 of 8 Report Format Version 5.0.0 5. ANTENNA GAIN The antennas provided to the EUT, please refer to the following table: Transmitter Circuit Brand Model Gain (dBi) (Exclude cable loss) Cable Loss (dB) Net Gain (dBi) (Include cable loss) Antenna Type Connecter Type Frequency range (GHz to GHz) Cable Length (cm) Chain (0) FDK A3001 2 1 1 Chip U.FL 2.4~2.4835 6 1 2 -1 5.15~5.85 Chain (1) FDK A3001 2 1.5 0.5 Chip U.FL 2.4~2.4835 16 1 2.5 -1.5 5.15~5.85 Report No.: SA140128E04 7 of 8 Report Format Version 5.0.0 6. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER For 15.247 (2.4GHz): 802.11b: FREQUENCY BAND (MHz) CONDUCTED POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 2412 - 2462 120.318 3.76 20 0.05689 1.00 NOTE: 1. Directional gain = 10 log[(10 G1/20 + 10 G2/20 ) 2 / 2] = 3.76dBi. 802.11g: FREQUENCY BAND (MHz) CONDUCTED POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 2412 - 2462 835.103 3.76 20 0.39488 1.00 NOTE: 1. Directional gain = 10 log[(10 G1/20 + 10 G2/20 ) 2 / 2] = 3.76dBi. 802.11n (HT20): FREQUENCY BAND (…

Text truncated - open the document above for the full version.

Report No.: RF140128E04A 1 of 27 Report Format Version 5.0.0 Reference No.: 140303E10 DFS TEST REPORT REPORT NO.: RF140128E04A MODEL NO.: FXE2000-DG FCC ID: PQRFXE2000-DG RECEIVED: Jan. 28, 2014 TESTED: Mar. 15, 2014 ISSUED: Apr. 01, 2014 APPLICANT: Contec Co., Ltd. ADDRESS: 3-9-31, Himesato, Nishiyodogawa-ku Osaka Japan 555-0025 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF140128E04A 2 of 27 Report Format Version 5.0.0 Reference No.: 140303E10 Table of Contents RELEASE CONTROL RECORD ........................................................................................ 3 1. CERTIFICATION .................................................................................................... 4 2. EUT INFORMATION ............................................................................................... 5 2.1 OPERATING FREQUENCY BANDS AND MODE OF EUT ..................................... 5 2.2 EUT SOFTWARE AND FIRMWARE VERSION ...................................................... 5 2.3 DESCRIPTION OF AVAILABLE ANTENNAS TO THE EUT .................................... 5 2.4 EUT MAXIMUM CONDUCTED POWER ................................................................ 6 2.5 EUT MAXIMUM EIRP POWER ............................................................................... 7 2.6 TRANSMIT POWER CONTROL (TPC) .................................................................. 8 2.7 STATEMENT OF MAUNFACTURER ...................................................................... 8 3. U-NII DFS RULE REQUIREMENTS ....................................................................... 9 3.1 WORKING MODES AND REQUIRED TEST ITEMS .............................................. 9 3.2 TEST LIMITS AND RADAR SIGNAL PARAMETERS ........................................... 10 4. TEST & SUPPORT EQUIPMENT LIST ................................................................. 13 4.1 TEST INSTRUMENTS .......................................................................................... 13 4.2 DESCRIPTION OF SUPPORT UNITS .................................................................. 13 5. TEST PROCEDURE ............................................................................................. 14 5.1 BVADT DFS MEASUREMENT SYSTEM: ............................................................. 14 5.2 CALIBRATION OF DFS DETECTION THRESHOLD LEVEL: ............................... 15 5.3 DEVIATION FROM TEST STANDARD ................................................................. 16 5.4 CONDUCTED TEST SETUP CONFIGURATION .................................................. 16 5.4.1 CLIENT WITHOUT RADAR DETECTION MODE ................................................. 16 6. TEST RESULTS ................................................................................................... 17 6.1 SUMMARY OF TEST RESULTS .......................................................................... 17 6.2 DETAILED TEST RESULTS ................................................................................. 18 6.2.1 TEST MODE: DEVICE OPERATING IN CLIENT WITHOUT RADAR DETECTION MODE................................................................................................................... 18 6.2.1.1 DFS DETECTION THRESHOLD .......................................................................... 18 6.2.1.2 CHANNEL CLOSING TRANSMISSION AND CHANNEL MOVE TIME ................. 19 6.2.1.3 NON- OCCUPANCY PERIOD .............................................................................. 20 6.2.1.4 NON-ASSOCIATED TEST .................................................................................... 22 6.2.1.5 NON- CO-CHANNEL TEST .................................................................................. 22 7. INFORMATION ON THE TESTING LABORATORIES .......................................... 23 8. APPENDIX-A ........................................................................................................ 24 9. APPENDIX B - MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB ................................................................................... 27 Report No.: RF140128E04A 3 of 27 Report Format Version 5.0.0 Reference No.: 140303E10 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED RF140128E04A Original release Apr. 01, 2014 Report No.: RF140128E04A 4 of 27 Report Format Version 5.0.0 Reference No.: 1…

Text truncated - open the document above for the full version.

Report No.: RF140128E04 1 of 106 Report Format Version 5.2.0 Reference No.: FCC TEST REPORT (15.247) REPORT NO.: RF140128E04 MODEL NO.: FXE2000-DG FCC ID: PQRFXE2000-DG RECEIVED: Jan. 28, 2014 TESTED: Feb. 10 to 13, 2014 ISSUED: Apr. 01, 2014 APPLICANT: Contec Co., Ltd. ADDRESS: 3-9-31, Himesato, Nishiyodogawa-ku Osaka Japan 555-0025 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF140128E04 2 of 106 Report Format Version 5.2.0 Reference No.: Table of Contents RELEASE CONTROL RECORD ........................................................................................ 5 1. CERTIFICATION .................................................................................................... 6 2. SUMMARY OF TEST RESULTS ............................................................................ 7 2.1 MEASUREMENT UNCERTAINTY .......................................................................... 8 3. GENERAL INFORMATION ..................................................................................... 9 3.1 GENERAL DESCRIPTION OF EUT ....................................................................... 9 3.2 DESCRIPTION OF TEST MODES ....................................................................... 11 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........................ 12 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ....................................... 15 3.4 DUTY CYCLE OF TEST SIGNAL ......................................................................... 16 3.5 DESCRIPTION OF SUPPORT UNITS .................................................................. 18 3.6 CONFIGURATION OF SYSTEM UNDER TEST ................................................... 19 4. TEST TYPES AND RESULTS (FOR 2.4GHz, 2.400 ~ 2.4835GHz BAND) ........... 20 4.1 CONDUCTED EMISSION MEASUREMENT ........................................................ 20 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ...................................... 20 4.1.2 TEST INSTRUMENTS .......................................................................................... 20 4.1.3 TEST PROCEDURES .......................................................................................... 21 4.1.4 DEVIATION FROM TEST STANDARD ................................................................. 21 4.1.5 TEST SETUP ....................................................................................................... 21 4.1.6 EUT OPERATING CONDITIONS ......................................................................... 22 4.1.7 TEST RESULTS ................................................................................................... 23 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................ 25 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............. 25 4.2.2 TEST INSTRUMENTS .......................................................................................... 26 4.2.3 TEST PROCEDURES .......................................................................................... 28 4.2.4 DEVIATION FROM TEST STANDARD ................................................................. 28 4.2.5 TEST SETUP ....................................................................................................... 29 4.2.6 EUT OPERATING CONDITIONS ......................................................................... 29 4.2.7 TEST RESULTS ................................................................................................... 30 4.3 6DB BANDWIDTH MEASUREMENT ................................................................... 43 4.3.1 LIMITS OF 6DB BANDWIDTH MEASUREMENT ................................................. 43 4.3.2 TEST INSTRUMENTS .......................................................................................... 43 4.3.3 TEST PROCEDURE ............................................................................................. 43 4.3.4 DEVIATION FROM TEST STANDARD ................................................................. 43 4.3.5 TEST SETUP ....................................................................................................... 43 4.3.…

Text truncated - open the document above for the full version.

Report No.: RF140128E04-1 1 of 80 Report Format Version 5.2.0 FCC TEST REPORT (15.407) REPORT NO.: RF140128E04-1 MODEL NO.: FXE2000-DG FCC ID: PQRFXE2000-DG RECEIVED: Jan. 28, 2014 TESTED: Feb. 10 to Mar. 08, 2014 ISSUED: Apr. 01, 2014 APPLICANT: Contec Co., Ltd. ADDRESS: 3-9-31, Himesato, Nishiyodogawa-ku Osaka Japan 555-0025 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF140128E04-1 2 of 80 Report Format Version 5.2.0 Table of Contents RELEASE CONTROL RECORD ........................................................................................ 4 1. CERTIFICATION .................................................................................................... 5 2. SUMMARY OF TEST RESULTS ............................................................................ 6 2.1 MEASUREMENT UNCERTAINTY .......................................................................... 7 3. GENERAL INFORMATION ..................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT(WLAN) ........................................................... 8 3.2 DESCRIPTION OF TEST MODES ....................................................................... 11 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........................ 12 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ....................................... 14 3.4 DUTY CYCLE OF TEST SIGNAL ......................................................................... 15 3.5 DESCRIPTION OF SUPPORT UNITS .................................................................. 18 3.6 CONFIGURATION OF SYSTEM UNDER TEST ................................................... 19 4. TEST TYPES AND RESULTS .............................................................................. 20 4.1 CONDUCTED EMISSION MEASUREMENT ........................................................ 20 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ...................................... 20 4.1.2 TEST INSTRUMENTS .......................................................................................... 20 4.1.3 TEST PROCEDURES .......................................................................................... 21 4.1.4 DEVIATION FROM TEST STANDARD ................................................................. 21 4.1.5 TEST SETUP ....................................................................................................... 21 4.1.6 EUT OPERATING CONDITIONS ......................................................................... 22 4.1.7 TEST RESULTS ................................................................................................... 23 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................ 25 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............. 25 4.2.2 LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS.......... 25 4.2.3 TEST INSTRUMENTS .......................................................................................... 26 4.2.4 TEST PROCEDURES .......................................................................................... 28 4.2.5 DEVIATION FROM TEST STANDARD ................................................................. 28 4.2.6 TEST SETUP ....................................................................................................... 29 4.2.7 EUT OPERATING CONDITION ............................................................................ 29 4.2.8 TEST RESULTS ................................................................................................... 30 4.3 TRANSMIT POWER MEASUREMENT ................................................................ 58 4.3.1 LIMITS OF TRANSMIT POWER MEASUREMENT .............................................. 58 4.3.2 TEST INSTRUMENTS…

Text truncated - open the document above for the full version.