PS6R3003-A1Packetwave Point-to-Point

PacketWave 200 Series Subscriber Equipment Manual 10004880 Rev D1, December 2003 PacketWave Fixed Wireless Broadband Access System PacketWave 200 Series Subscriber Equipment Installation and Operation Manual PacketWave 200 Installation and Operation ©Copyright 2003 by Aperto Networks All rights reserved. Specifications subject to change. Aperto, PacketWave, and WaveCenter are trademarks of Aperto Networks. All other trademarks used herein are the property of their respective owners. Aperto Networks 1637 South Main Street Milpitas, CA 95035 USA Phone: 408.719.9977 Fax: 408.719.9970 www.apertonet.com iii 10004880 Rev. D1 Regulatory Information Part 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • this device may not cause harmful electromagnetic interference, and • this device must accept any interference received including interference that may cause undesired operations. FCC Notice: Radio and Television Interference The PacketWave 200 Series Subscriber Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfer- ence to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment or device. • Connect the equipment to an outlet other than the receiver's. • Consult a dealer or an experienced radio/TV technician for assistance. iv 10004880 Rev. D1 RF Exposure Notice The installer shall mount all transmit antennas so as to comply with the limits for human exposure to radio frequency (RF) fields per paragraph 1.1307 of FCC regulations. The FCC requirements incorporate limits for Maximum Permissible Exposure (MPE) in terms of electric field strength, magnetic field strength, and power density. CAUTION:5.8 GHz ISM — To comply with FCC RF exposure requirements, antennas used for this device must be installed to provide a separation distance of at least 1.5m from all persons to satisfy RF exposure compliance. CAUTION:2.5 GHz MMDS — To comply with FCC RF exposure requirements in sec- tion 1.1307, a minimum separation distance of 20 cm is required between this antenna and all persons. Canadian Standards Compliance This Class B digital apparatus complies with Canadian ICES-003 Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada v 10004880 Rev. D1 CE Notice Declaration of Conformity Aperto Networks Inc. of 1637 S. Main Street, Milpitas CA 95037, USA, declare under our sole responsibility that the product PacketWave 3.5 GHz system (3.4-3.7 GHz operation) to which this declaration relates, is in conformity with the following standards and/or other normative documents. •EN 301 753 •EN301 489-4 •EN60950 We hereby declare that all essential radio test suites have been carried out and that the above named product is in conformity to all the essential requirements of Directive 1999/ 5/EC. The conformity assessment procedure referred to in Article 10 and detailed in Annex [III] or [IV] of Directive 1999/5/EC has been followed with the involvement of the following Notified Body: Compliance Certification Services, 561F Monterey Road, Morgan Hill, CA 95037 0984 vi 10004880 Rev. D1 The PacketWave 3.5 GHz system is approved in the following countries: CountryLower bandUpper band Austria3,510 - 3,5493,560 - 3,599 Belgium3,450 - 3,5003,550 - 3,600 Denmark3,410 - 3,4903,510 - 3,590 Finland3,410 - 3,5003,510 - 3,600 France3,465 - 3,4953,565 - 3,595 Germany3,410 - 3,580 Greece3,410 - 3,438 3,459 - 3,473 3,476.5 - 3,497.5 3,510 - 3,538 3,559 - 3,573 3,576.5 - 3,597.5 Iceland3,400 - 3,600 Ireland3,410 - 3,4353,475 - 3,500 3,510 - 3,5353,575 - 3,600 Netherlands3,500 - 3,5303,550 - 3,580 Norway3,413.5 - 3,5003,513.5 - 3,600 Portugal3,410 - 3,4383,600 - 3,800 3,510 - 3,538 Spain3,400 - 3,4603,500 - 3,560 Sweden3,400 - 3,600 Switzerland3,410 - 3,5003,510 - 3,600 UK3,480 - 3,5003,580 - 3,600 vii 10004880 Rev. D1 Ta b l e o f Contents Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii Preface Scope of This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi Conventions Used in This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii Intended Audience for this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii General Cautions and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii Chapter 1. QuickStart Guide Chapter 2. Overview Models and Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 VLAN and PPPoE/PPP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Subscriber Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Outdoor Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Automatic Frequency Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Interface Box . . . . . . . . . …

Text truncated - open the document above for the full version.

1637 S. Main Street Milpitas CA 95035 (408) 719-7799 (408) 719-9970 FAX [email protected] August 6, 2004 Federal Communications Commission Equipment Authorization branch 7435 Oakland Mills Road Columbia, MD 21046 Re: Request for Confidentiality Gentlemen: In reference to the application under FCC ID: PS6R3003-A1 and pursuant to Sections 0.457(d)(l)(ii) and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of the accompanying information as outlined below: Schematics Block Diagrams Theory of Operation. These documents contain detailed system and equipment description and related information about the product that Aperto Networks to be proprietary, confidential, and a custom design and, otherwise, would not release to the general public. Since this design is a basis from which future technological products will evolve, Aperto Networks considers that this information would be of benefit to its competitors, and that disclosure of the information in these documents would give competitors an unfair advantage in the market. Sincerely, Dean S.K. Chang Director, Product Management Aperto Networks

1637 S. Main Street Milpitas CA 95035 (408) 719-9977 (408) 719-9970 FAX [email protected] August 6, 2004 Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern: We, the undersigned, hereby authorize Compliance Engineering Services, Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Compliance Engineering Service, Inc. on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This authorization is valid until further written notice from the applicant. Sincerely Yours, Dean S.K. Chang Director, Product Management Aperto Networks

1 Mike Kuo From: Kathy Yao Sent: August302004Monday 11:22 AM To: Mike Kuo Cc: Chuck Cowden; Claire Hoque Subject: RE: Aperto Networks Inc. , FCC ID: PS6R3002-A1, Assessment NO.: AN04T4114, Notice#1 Importance: High -----Original Message----- From: Claire Hoque Sent: Wednesday, August 25, 2004 1:42 PM To: Mike Kuo Cc: Kathy Yao Subject: RE: Aperto Networks Inc. , FCC ID: PS6R3002-A1, Assessment NO.: AN04T4114, Notice#1 Hi Mike, Here are the answers. Question #1: The proposed antenna to be used with this point-to-point operation is phased array antenna with multiple radiating elements. Please address the following issues related to phased array antenna: a. How many beams can be transmitting simultaneously b. What are the beamwidth c. How many radiating elements in the antenna d. What is the max. output power for each element e. What are the aggregate transmitted power simultaneously <Aperto>Aperto system is not Phase array system. "patch," not "phased" Patches, or simply a number of blobs of copper in a square shape slapped(etched) on a flat dielectric material that direct the beam in the proper direction within a limited angle. Also known as flat panel antennas. A phased arrayed system on the other hand, requires two or more antenna elements (4 typical, but can even be 16 or more) , where the electromagnetic wave arriving at these elements is separately controlled by a digital signal processor in a manner such that the phases of said signals add and cancel according to an algorithm that makes the signal emanating from the entire phased-antenna-system directional and controllable in real time. A fairly complex system which at times collapses under its own complexity. Ours is just a simple 'antenna,' with dual polarity, but only one functioning at a time and with equal gain and symmetry in either polarization. Question #2: The MPE estimate is using the total output power measured at antenna connector which may not be the true effective power to each of radiated element. Please consider the aggregate output power to the number of active radiating elements and submit MPE estimate again. <answer>no need based on Q1 answer. Question #3: What is the data rate used during each of test. <Aperto>we do all these tests at 4.77 Mbaud. Question #4: The specification in A-3 of user manual listed the operating frequency for 5.8GHz unit is from 5725 - 5875MHz which does not agree the operating frequency range and the specified frequency range is outside the authorized frequency band allowed in section 15.247 of FCC rules. Please explain. <Aperto>Aperto Networks sells this product world-wide and some customers have spectrum outside of the designated US frequency band. These customers accept the FCC certification with the stated wider frequency band for their regulatory certification. US customers are obliged to only operate within the limits of frequencies specified by CFR47.15.247 but we want to note in the report that the device was tested to a wider frequency range. Question #5: How many channels are allowed within 5728 - 5847MHz band / <Aperto>20 in 6 MHz channels; 40 in 3 MHz, and any combination of these that results in less than 120 MHz of BW 2 Thanks, Claire

PROPOSED FCC ID LABEL AND LOCATION APERTO NETWORKS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: PS6R3003-A1 FCC ID LABEL LOCATION

FCC CFR47 PART 15 SUBPART C CERTIFICATION TEST REPORT FOR PACKETWAVE POINT TO POINT MODEL NUMBER: PW210, PW220, PW230 FCC ID: PS6R3003-A1 REPORT NUMBER: 04U2749-1 ISSUE DATE: JULY 28, 2004 Prepared for APERTO NETWORKS 1637S. MAIN STREET MILPITAS CALIFORNIA 95035, USA Prepared by COMPLIANCE CERTIFICATION SERVICES 561F MONTEREY ROAD, MORGAN HILL, CA 95037, USA TEL: (408) 463-0885 FAX: (408) 463-0888 REPORT NO: 04U2749-1 DATE: AUGUST 042004 EUT: PACKETWAVE PONIT TO POINT FCC ID:PS6R3003-A1 Page 2 of 51 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION.................................................................................................. 3 2. EUT DESCRIPTION.......................................................................................................................... 4 3. TEST METHODOLOGY .................................................................................................................. 5 4. FACILITIES AND ACCREDITATION .......................................................................................... 5 5. CALIBRATION AND UNCERTAINTY.......................................................................................... 6 5.1. MEASURING INSTRUMENT CALIBRATION ............................................................................. 6 5.2. MEASUREMENT UNCERTAINTY ............................................................................................... 6 5.3. TEST AND MEASUREMENT EQUIPMENT................................................................................ 7 6. SETUP OF EQUIPMENT UNDER TEST ....................................................................................... 8 7. APPLICABLE LIMITS AND TEST RESULTS ........................................................................... 10 7.1. 6 dB BANDWIDTH ..................................................................................................................... 10 7.2. 99% BANDWIDTH ..................................................................................................................... 14 7.3. PEAK OUTPUT POWER............................................................................................................ 18 7.4. MAXIMUM PERMISSIBLE EXPOSURE ................................................................................... 23 7.5. AVERAGE POWER..................................................................................................................... 26 7.6. PEAK POWER SPECTRAL DENSITY ....................................................................................... 27 7.7. CONDUCTED SPURIOUS EMISSIONS.................................................................................... 31 7.8. RADIATED EMISSIONS.............................................................................................................38 7.8.1. TRANSMITTER RADIATED SPURIOUS EMISSIONS ................................................. 38 7.8.2. TRANSMITTER RADIATED EMISSIONS ABOVE 1 GHZ .......................................... 41 7.8.3. WORST-CASE RADIATED EMISSIONS BELOW 1 GHz ............................................. 42 7.9. POWERLINE CONDUCTED EMISSIONS ................................................................................ 43 8. SETUP PHOTOS .............................................................................................................................. 47 REPORT NO: 04U2749-1 DATE: AUGUST 042004 EUT: PACKETWAVE PONIT TO POINT FCC ID:PS6R3003-A1 Page 3 of 51 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. 1. TEST RESULT CERTIFICATION COMPANY NAME: APERTO NETWORKS 1637 S. MAIN STREET MILPITAS CA.95035, USA EUT DESCRIPTION: PACKETWAVE POINT TO MULTIPOINT MODEL NAME: PW210, PW220, PW230 MODEL DIFFERENCE: The three models are identical to each other except that they have different software features inside, which allow the products to be configured as VLAN or just a HUB. DATE TESTED: DECEMBER 03-JULY 28, 2004 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 15 SUBPART C NO NON-COMPLIANCE NOTED Compliance Certification Services, Inc. tested the above equipment in accordance with the requirements set forth in the above standards. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: This document reports conditions under which testing was conducted and results of tests performed. This document may not be altered or revised in any way unless done so by Compliance Certification Services and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by Compliance Certification Services will constitute fraud and shall nullify the document. Approved & Released For CCS By: Tested By: THU CHAN CHIN PANG EMC SUPERVISOR EMC TECHNICIAN COMPLIANCE CERTIFICATION SERVICES COMPLIANCE CERTIFICATION SERVICES REPORT NO: 04U2749-1 DATE: AUGUST 042004 EUT: PACKETWAVE PONIT TO POINT FCC ID:PS6R3003-A1 Page 4 of 51 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compl…

Text truncated - open the document above for the full version.

REPORT NO: 04U2749-1 DATE: AUGUST 042004 EUT: PACKETWAVE PONIT TO POINT FCC ID:PS6R3003-A1 Page 47 of 51 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. 8. SETUP PHOTOS ANTENNA PORT CONDUCTED RF MEASUREMENT SETUP ANTENNA PORT CONDUCTED PHOTO REPORT NO: 04U2749-1 DATE: AUGUST 042004 EUT: PACKETWAVE PONIT TO POINT FCC ID:PS6R3003-A1 Page 48 of 51 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. RADIATED RF MEASUREMENT SETUP RADIATED FRONT PHOTO REPORT NO: 04U2749-1 DATE: AUGUST 042004 EUT: PACKETWAVE PONIT TO POINT FCC ID:PS6R3003-A1 Page 49 of 51 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. RADIATED BACK PHOTO REPORT NO: 04U2749-1 DATE: AUGUST 042004 EUT: PACKETWAVE PONIT TO POINT FCC ID:PS6R3003-A1 Page 50 of 51 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP LINE CONDUCTED FRONT PHOTO REPORT NO: 04U2749-1 DATE: AUGUST 042004 EUT: PACKETWAVE PONIT TO POINT FCC ID:PS6R3003-A1 Page 51 of 51 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. END OF REPORT LINE CONDUCTED BACK PHOTO