PWO271230SA800MHZ AMPS & 1900PCS BOOSTER AMPLIFIER

Amplifier Installation Guide SignalBoost Vehicle Wireless Dual-Band Cellular / PCS Amplifier Contents: Guarantee and Warranty · · · · · · · · · · · · · · · · · · · · · · · · 1 How it Works · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2 Before Getting Started · · · · · · · · · · · · · · · · · · · · · · · · · · 3 Installing a Wilson Outside Antenna · · · · · · · · · · · · · · · 4 Installing a Wilson Amplifier · · · · · · · · · · · · · · · · · · · · · · 5 Installing a Wilson Inside Antenna (Wireless) · · · · · · · · 6 Attaching a Wilson Inside Antenna (Laptop/Data Card) · · 7 Optional Cell Phone Cradle Plus · · · · · · · · · · · · · · · · · · 7 Powering Up a Wilson Amplifier · · · · · · · · · · · · · · · · · · · 8 Understanding the Amplifier Lights · · · · · · · · · · · · · · · · 8 Warnings and Recommendations · · · · · · · · · · · · · · · · · 9 About Wilson Electronics · · · · · · · · · · · · · · · · · · · · · · · · 10 Amplifier Specifications · · · · · · · · · · · · · · · · · · Back Cover Wilson ® Electronics, Inc. Warning: This manual contains important safety and operating information. Please read and follow the instructions in this manual. Failure to do so could be hazardous and result in damage to your amplifier. !  30-Day Money-Back Guarantee All Wilson Electronics products are protected by Wilson’s 30-day money-back guarantee. If, for any reason, the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase. 1-Year Warranty Wilson Electronics amplifiers are warranted for one (1) year against defects in workmanship and / or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase. Amplifiers may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by Wilson Electronics. Wilson shall, at its option, either repair or replace the product. Wilson Electronics will pay for delivery of the repaired or replaced product back to the original consumer. This warranty does not apply to any amplifiers determined by Wilson Electronics to have been subjected to misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties. RMA numbers may be obtained by phoning Technical Support at 866-294-1660. Disclaimer: The information provided by Wilson Electronics, Inc. is believed to be complete and accurate. However, no responsibility is assumed by Wilson Electronics, Inc. for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use. Copyright © 2008 Wilson Electronics, Inc. All rights reserved. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.  Installation Instructions for the Following Wilson Amplifier: SignalBoost Vehicle Wireless Dual-Band Amplifier Part # 801230 Model #271230 FCC ID: PWO271230SA (pending) IC:4726A-271230SA (pending) The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. Inside this Package How it Works Your new Wilson amplifier has been carefully engineered to significantly improve the performance of your cell phone or cellular data card in mobile applications. Together with an outside antenna, the amplifier’s state-of-the-art technology is designed to increase your signal up to 10 times, reduce disconnects and dropouts, and increase data communication rates needed for 3G technologies. The outside antenna will collect the cell tower signal and send it through the cable to the amplifier. The signal is then boosted and sent through the Ultra-slim inside antenna. Your cell phone or data card then communicates with the improved signal. When the cell phone or data card transmits, the signal goes through the inside antenna, is boosted by the amplifier and broadcast back to the cell tower through the outside antenna. The Ultra-slim antenna may also be attached directly to a laptop or cellular data card for maximum signal performance. Wilson Electronics manufactures a wide variety of antennas to help you customize your amplifier for your specific application. Several are shown below. See your dealer or visit www.wilsonelectronics.com. Wireless amplifier NMO Mount Dual-BandMagnet Mount Dual-Band Trucker Mount Dual-Band Mini Magnet Dual-BandMarine Antenna Dual-Band NOTE: Use of this amplifier with an antenna gain higher than 6.12 dBi is in violation of FCC regulations for which the offender is fully liable. All Wilson mobile antennas are 6.12 dBi or less. Ultra-slim antenna DC plug-in power supply  Before Getting Started This guide will help you properly install Wilson’s SignalBoost Vehicle Wireless amplifier. It is important to read through all of the installation steps for your particular application prior to installing any equipment. Read through the instructions, visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment. If you do not understand the instructions in full, seek professional help, or contact Wilson Technical Support at 866-294-1660. Warning: In a wireless installation, do not plug the amplifier directly into the cell phone or data card using an antenna adapter. It will damage the amplifier. ! Outside Antenna Ultra-slim Inside Antenna Amplifier DC Power Supply Cell Phone PDA Notebook Outside Antenna Amplifier DC Power Supply Laptop with Ultra- slim antenna attached (see pg. 7) Installation Diagram Inside Antenna Warning: Do not plug the amplifier directly into the laptop or data card using an antenna adapter. It will damage the amplifier. ! Installation Diagram Laptop Use  Installing a Wilson…

Text truncated - open the document above for the full version.

February 28, 2008 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Data Confidentiality Wilson Electronics requests confidentiality of certain documentation provided with the submission of our model 271230 amplifier under FCC ID: PWO271230SA in accordance with sections 0.457 and 0.459 of the Commission’s regulations. We request that the following documents be kept confidential: 1. Schematic Diagrams, file names: 271230 RX Schematic.jpg, 271230 TX Schematic.jpg 2. Operational Description, file name: 271230 Operational Description.doc 3. Block Diagram, file name: 271230 Block Diagram. xls The above material is confidential and contains proprietary trade secrets and technical data which must be kept from competitors. Public access to these items could result in duplication of our circuitry and/or techniques thereby reducing our competitive advantage and causing us severe damage. Sincerely, Richard M. Kline Senior Electrical Engineer

DUT External Photos Back Bottom Front Top Inside Antenna Outside Antenna

FCC ID and IC Label Proposed Location – Bottom of DUT

DUT Internal Photos Open Case Board Top Board Bottom

WILSON ELECTRONICS, INC. FCC ID: PWO271230SA PARTS LIST All of the information that would be on a parts list (component values, part no. of active devices, etc.) is in the schematic diagram, so we don't have a separate parts list.

WILSON ELECTRONICS, INC. FCC ID: PWO271230SA TUNING PROCEDURE – No tuning procedure is available or required for this device. There is no tuning required.

Minimum Safe Distance From Antennas Based upon FCC OET Bulletin 65 and other FCC Sources INPUT DATA Frequency MHz1850 Pout Watts1.5450 Duty Cycle Percent100.0% Ant. Gain dBi6.12 Coax Loss dB4.12 Min. Distance Inches5.50 Min. Distance Centimeters13.96 ERP (Watts)1.4931 EIRP (Watts)2.4487 REFERENCE DAT A Antenna Gain (non-log)4.09 Coax loss (non-log)0.39 Calculated limit (mw/cm2)1.00 FCC Limit (mw/cm2)1.00 NOTES : (1) Valid only between 300 MHz - 100,000 MHz (3) Mobile antenna distances shall be no less than 8 inches. For Amplifier Model Number: Frequency Band (MHz) Mobile or Building? Outside or Inside Antenna? Antenna Type: Safe Distance (inches): Signature: Date: RESULTS OF CALCULATIONS SUMMARY FOR PUBLICATION 1900 271230 (2) Calculations are sufficient for determining antenna safe distance for mobile antennas provided that calculated ERP < 1.5 watts for frequencies equal to or below 1.5 GHz, and calculated ERP < 3 watts for frequencies above 1.5 GHz. (5) Indoor building antenna criteria is the same as the criteria for mobile antennas (see #2 & #3). (4) There are no predefined ERP and distance limitations for fixed outside (building) antennas (see #5). 2/22/2008 Mobile 10 Outside not exceed 2.00 dBi Magnet-Mount or any antenna whose gain less coax loss does RF Exp_271230 MPE1900 OUTSIDE.xls

Minimum Safe Distance From Antennas Based upon FCC OET Bulletin 65 and other FCC Sources INPUT DATA Frequency MHz869 Pout Watts0.0700 Duty Cycle Percent100.0% Ant. Gain dBi3.00 Coax Loss dB0.00 Min. Distance Inches1.72 Min. Distance Centimeters4.38 ERP (Watts)0.0852 EIRP (Watts)0.1397 REFERENCE DAT A Antenna Gain (non-log)2.00 Coax loss (non-log)1.00 Calculated limit (mw/cm2)0.58 FCC Limit (mw/cm2)f/1500 NOTES : (1) Valid only between 300 MHz - 100,000 MHz (3) Mobile antenna distances shall be no less than 8 inches. For Amplifier Model Number: Frequency Band (MHz) Mobile or Building? Outside or Inside Antenna? Antenna Type:antenna whose gain less coax loss does not exceed 3 dBi Safe Distance (inches): Signature: Date: Inside 2/22/2008 Mobile 8 Ultra-slim, Cradle Plus, or any RESULTS OF CALCULATIONS SUMMARY FOR PUBLICATION 800 271230 (2) Calculations are sufficient for determining antenna safe distance for mobile antennas provided that calculated ERP < 1.5 watts for frequencies equal to or below 1.5 GHz, and calculated ERP < 3 watts for frequencies above 1.5 GHz. (5) Indoor building antenna criteria is the same as the criteria for mobile antennas (see #2 & #3). (4) There are no predefined ERP and distance limitations for fixed outside (building) antennas (see #5). RF Exp_271230 MPE 800 INSIDE.xls

Minimum Safe Distance From Antennas Based upon FCC OET Bulletin 65 and other FCC Sources INPUT DATA Frequency MHz824 Pout Watts1.5380 Duty Cycle Percent100.0% Ant. Gain dBi6.12 Coax Loss dB4.10 Min. Distance Inches7.42 Min. Distance Centimeters18.83 ERP (Watts)1.4932 EIRP (Watts)2.4488 REFERENCE DAT A Antenna Gain (non-log)4.09 Coax loss (non-log)0.39 Calculated limit (mw/cm2)0.55 FCC Limit (mw/cm2)f/1500 NOTES : (1) Valid only between 300 MHz - 100,000 MHz (3) Mobile antenna distances shall be no less than 8 inches. For Amplifier Model Number: Frequency Band (MHz) Mobile or Building? Outside or Inside Antenna? Antenna Type: Safe Distance (inches): Signature: Date: Outside not exceed 2.02 dBi Magnet-Mount or any antenna whose gain less coax loss does 2/22/2008 Mobile 10 RESULTS OF CALCULATIONS SUMMARY FOR PUBLICATION 800 271230 (2) Calculations are sufficient for determining antenna safe distance for mobile antennas provided that calculated ERP < 1.5 watts for frequencies equal to or below 1.5 GHz, and calculated ERP < 3 watts for frequencies above 1.5 GHz. (5) Indoor building antenna criteria is the same as the criteria for mobile antennas (see #2 & #3). (4) There are no predefined ERP and distance limitations for fixed outside (building) antennas (see #5). RF Exp_271230 MPE 800 OUTSIDE.xls

Minimum Safe Distance From Antennas Based upon FCC OET Bulletin 65 and other FCC Sources INPUT DATA Frequency MHz1930 Pout Watts0.0250 Duty Cycle Percent100.0% Ant. Gain dBi3.00 Coax Loss dB0.00 Min. Distance Inches0.78 Min. Distance Centimeters1.99 ERP (Watts)0.0304 EIRP (Watts)0.0499 REFERENCE DAT A Antenna Gain (non-log)2.00 Coax loss (non-log)1.00 Calculated limit (mw/cm2)1.00 FCC Limit (mw/cm2)1.00 NOTES : (1) Valid only between 300 MHz - 100,000 MHz (3) Mobile antenna distances shall be no less than 8 inches. For Amplifier Model Number: Frequency Band (MHz) Mobile or Building? Outside or Inside Antenna? Antenna Type: Safe Distance (inches): Signature: Date: RESULTS OF CALCULATIONS SUMMARY FOR PUBLICATION 1900 271230 (2) Calculations are sufficient for determining antenna safe distance for mobile antennas provided that calculated ERP < 1.5 watts for frequencies equal to or below 1.5 GHz, and calculated ERP < 3 watts for frequencies above 1.5 GHz. (5) Indoor building antenna criteria is the same as the criteria for mobile antennas (see #2 & #3). (4) There are no predefined ERP and distance limitations for fixed outside (building) antennas (see #5). 2/22/2008 Mobile 8 Inside loss does not exceed 3 dBi Ultra-slim, Cradle Plus, or any antenna whose gain less coax RF Exp_271230 MPE 1900 INSIDE.xls

FCC AND IC TEST REPORT PER PART 22H, PART 24E, RSS-131 SIGNAL BOOSTER Applicant Wilson Electronics, Inc. Address 3301 E. Deseret Drive St. George, Utah 84790 USA FCC ID PWO271230SA IC Label IC: 4726A-271230SA Model Number 271230 Product Description 800MHz AMPS & 1900 PCS Booster Amplifier Date Sample Received November 14, 2007 Date Tested November 30, 2007 Tested By Nam Nguyen Approved By Mario de Aranzeta Report No. 3591AUT7TestReport.pdf Test Results PASS FAIL THE ATTACHED REPORT SHALL NOT BE REPRODUCED EXCEPT IN FULL WITHOUT THE WRITTEN APPROVAL OF TIMCO ENGINEERING, INC. 849 NW STATE ROAD 45 NEWBERRY, FL 32669 USA PH: 888.472.2424 OR 352.472.5500 FAX: 352.472.2030 EMAIL: [email protected] HTTP://WWW.TIMCOENGR.COM Test Certificate # 0955-01 APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO271230, IC: 4726A-271230 Repot #:W:\W\WILSON_PWO\3591AUT7\3591AUT7TestReport.doc Page 2 of 61 TABLE OF CONTENTS ATTESTATION................................................................................................. 4 REPORT SUMMARY ........................................................................................ 5 TEST ENVIRONMENT ..................................................................................... 5 TEST SETUP ................................................................................................... 5 DEVICE UNDER TEST INFORMATION ............................................................ 6 EQUIPMENT LIST ........................................................................................... 7 TEST PROCEDURE ......................................................................................... 8 RF POWER OUTPUT........................................................................................ 11 Test Data Table 1 – Output Power – CDMA 1900 – Uplink/Downlink....... 11 Test Data Table 2 – Output Power – EDGE 1900 – Uplink/Downlink ....... 11 Test Data Table 3 – Output Power – GSM 1900 – Uplink/Downlink ......... 11 Test Data Table 4 – Output Power – CDMA 800 – Uplink/Downlink......... 12 Test Data Table 5 – Output Power – EDGE 800 – Uplink/Downlink ......... 12 Test Data Table 6 – Output Power – GSM 800 – Uplink/Downlink ........... 12 Test Data Table 7 – Output Power – AMPS 800 – Uplink/Downlink ......... 12 INPUT/OUTPUT MODULATED AMPLITUDE COMPARISON AND BAND-EDGES COMPLIANCE ............................................................................................... 13 Test Data Table 8 – CDMA 1900 – Uplink/Downlink........................................... 14 Figure 1: CDMA – In vs. Out 1851.25MHz ............................................... 14 Figure 2: CDMA – In vs. Out 1908.75MHz ............................................... 15 Figure 3: CDMA – In vs. Out 1931.25MHz ............................................... 16 Figure 4: CDMA – In vs. Out 1988.75MHz ............................................... 17 Test Data Table 9 – EDGE 1900 – Uplink/Downlink ........................................... 18 Figure 5: EDGE – In vs. Out 1850.20MHz ............................................... 18 Figure 6: EDGE – In vs. Out 1909.80MHz ............................................... 19 Figure 7: EDGE – In vs. Out 1930.20MHz ............................................... 20 Figure 8: EDGE – In vs. Out 1989.80MHz ............................................... 21 Test Data Table 10 –GSM 1900 – Uplink/Downlink ............................................ 22 Figure 9: GSM – In vs. Out 1850.20MHz ................................................. 22 Figure 10: GSM – In vs. Out 1909.80MHz ............................................... 23 Figure 11: GSM – In vs. Out 1930.20MHz ............................................... 24 Figure 12: GSM – In vs. Out 1989.80MHz ............................................... 25 Test Data Table 11 – CDMA 800 – Uplink/Downlink........................................... 26 Figure 13: CDMA – In vs. Out 825.25MHz ............................................... 26 Figure 14: CDMA – In vs. Out 847.75 MHz .............................................. 27 Figure 15: CDMA – In vs. Out 870.25 MHz .............................................. 28 Figure 16: CDMA – In vs. Out 892.75 MHz .............................................. 29 Test Data Table 12 – EDGE 800 – Uplink/Downlink ........................................... 30 Figure 17: EDGE – In vs. Out 824.20 MHz .............................................. 30 Figure 18: EDGE – In vs. Out 848.80 MHz .............................................. 31 Figure 19: EDGE – In vs. Out 869.20 MHz .............................................. 32 APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO271230, IC: 4726A-271230 Repot #:W:\W\WILSON_PWO\3591AUT7\3591AUT7TestReport.doc Page 3 of 61 Figure 20: EDGE – In vs. Out 893.80 MHz .............................................. 33 Test Data Table 13 – GSM 800 – Uplink/Downlink ............................................. 34 Figure 21: GSM – In vs. Out 824.2 MHz .................................................. 34 Figure 22: GSM – In vs. Out 848.8 MHz .................................................. 35 Figure 23: GSM – In vs. Out 869.2MHz ................................................... 36 Figure 24: GSM – In vs. Out 893.8MHz ................................................... 37 Test Data Table 14 – AMPS 800 – Uplink/Downlink ........................................... 38 Figure 25: AMPS – In vs. Out 824.20 MHz............................................... 38 Figure 26: AMPS – In vs. Out 848.80 MHz............................................... 39 Figure 27: AMPS – In vs. Out 869.20 MHz............................................... 40 Figure 28: AMPS – In vs. Out 893.80 MHz............................................... 41 INTERMODULATION PRODUCT SPURIOUS EMISSIONS ............................... 42 Figure 29: CDMA 3 tones intermodulation - (1850 – 1910) MHz. ............. 43 Figure 30: CDMA 3 tones intermodulation - (1930 – 1990)…

Text truncated - open the document above for the full version.