PWO273201WIRELESS DUAL-BAND BI-DIRECTIONAL AMPLIFIER

Contents: How it Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Before Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Quick Installation Overview . . . . . . . . . . . . . . . . . . . . . . . .2 Installing the Outside Antenna . . . . . . . . . . . . . . . . . . . . . .2 Installing the Low-Profile Antenna . . . . . . . . . . . . . . . . . . .3 Installing a Wilson Electronics Signal Booster . . . . . . . . . .3 Powering Up a Wilson Electronics Signal Booster . . . . . . 4 Understanding the Signal Booster Lights . . . . . . . . . . . . . 4 Warnings and Recommendations . . . . . . . . . . . . . . . . . . .5 Guarantee and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . .6 Signal Booster Specifications . . . . . . . . . . . . . .Back Cover Note: This manual contains important safety and operating information . Please read and follow the instructions in this manual . Failure to do so could be hazardous and result in damage to your Signal Booster . Mobile Wireless Dual-Band Smart Technology ™ Signal Booster Appearance of device and accessories may vary . 1 Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660 Or email: [email protected] Mon.- Fri. Hours: 7am to 6 pm MST. 2 Installation Instructions for the Following Wilson Electronics Signal Boosters: Mobile Wireless Dual-Band Smart Technology ™ Signal Booster Model # 273201, Part # 801201, 801212, 801215 FCC ID: PWO273201 IC: 4726A-273201 Wireless Signal Booster DC plug-in power supply (301127) Low-Profile Antenna (301104) NMO Mount Dual-Band (301103) Magnet Mount Dual-Band (301101) Trucker Mount Tri-Band (301113) Mini Magnet Dual-Band (301130) Marine Antenna Dual-Band How it Works Your new Wilson Signal Booster has been carefully engineered to significantly improve the performance of your cell phone and cellular data card in mobile applications . Together with an Outside Antenna, the Signal Booster’s state-of-the-art technology is designed to increase your signal more than 20 times, reduces dropped calls and increase data communication rates needed for 3G technologies . The Outside Antenna will collect the cell tower signal and send it through the cable to the Signal Booster . The signal is then boosted and sent to the Inside Antenna . Your cellular device then communicates with the improved signal . When the cellular device transmits, the signal goes through the Inside Antenna, is boosted by the Signal Booster and transmitted to the cell tower through the Outside Antenna . Optional Antennas Before Getting Started This guide will help you properly install your Wilson Electronics Dual-Band Mobile Wireless Signal Booster . It is important to read through all of the installation steps for your particular application prior to installing any equipment. Read through the instructions, visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment . Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660. (Included with some kits) (Included with some kits) Wilson Electronics manufactures a wide variety of antennas to help you customize your Signal Booster for your specific application . Several authorized antennas are shown above . See your dealer or visit www.WilsonElectronics.com . (Included with some kits) The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met . Inside this Package Appearance of device and accessories may vary . 12 Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660 Or email: [email protected] Mon.- Fri. Hours: 7am to 6 pm MST. Warning: In a wireless installation, do not plug the Signal Booster directly into the cell phone and/ or data card using an antenna adapter . It may damage the Signal Booster, cell phone and/or data card . ! ! ! Quick Installation Overview Installing the Outside Antenna To receive the best cell signal, select a location in the center of the vehicle’s roof 12 inches away from any other antennas or windows . If the vehicle has a sunroof, it is important to separate the Inside and Outside Antennas by at least five feet . This prevents the Signal Booster from overloading or oscillating . As shown above . Follow the specific antenna installation instructions included with the Outside Antenna . Magnet - Mount Antenna Shown Part #301103 Carefully Pull Down Door Seal Run Cable Under Seal Tuck Cable Under Seal Separation of the Inside and Outside Antennas is very important . The metal roof of the vehicle acts as a barrier and helps shield the two antennas from each other, preventing oscillation (feedback) . The Outside Antenna must be installed vertically . Signal performance will be degraded if the antenna is not vertical . The antenna cable may run through the door to the Signal Booster . For a more professional looking installation, run the antenna cable under the door seal . The antenna cable is small enough to easily tuck under the door seal or plastic molding . Carefully pull down the door seal . Run the cable through the seal and push the seal back into place . This prevents constant wear and tear on the cable as the door opens and closes . Warning: Do not plug in the DC power supply until the Outside and Inside Antenna cables are attached to the Signal Booster . Warning: Do not use any type of glass-mount antenna with this Signal Booster . The Outside and Inside Antennas must be shielded from each other to prevent oscillation (feedback) . Installation Diagram Outside Antenna Inside Antenna Distance between antennas through a sunroof must be 5 feet or more . DC Power Supply Signal Booster Cell Phone PDA Notebook 3 Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660 Or email: [email protected] Mon.- Fri. Hours: 7am to 6 pm MST. 4 Place the Low-Profile Antenna on the side…

Text truncated - open the document above for the full version.

?wils,on' 3301 East Deseret Drrve St. George, Utah 84790 ffidffT"J,::[ilf.:.""'# Phone 800.204.4104 . Fax 435.656.2432 May 23,2012 Subject: Authorized lndividuals Re: FCC lD: PWO273201 To Whom lt May Concern: Please be advised that l, James W. Wilson, as contact of record in the Grantee Code data base, have designated Mr. Richard Kline of Wilson Electronics and Mr. Mario de Aranzeta of Timco Engineering as the persons responsible for the above referenced Wilson Electronics certificate application. Any and all acts carried out by Mr. Richard Kline or Mr. Mario de Aranzeta in matters pertaining to processes required in the FCC approval shall have the same legal authority as acts and communications by the undersigned. They are authorized to respond to any future issues or FCC requests regarding this project. This authorization is limited to the product referenced above. Please send any query, acknowledgement or response to this letter directly to Wilson Electronics. Sincerely, U ) - -t, J)- %^ "rW. Wilson President

May 23, 2012 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Data Confidentiality Gentlemen: Wilson Electronics, Inc. respectfully requests confidentiality of certain documentation provided with the submission of our model 273201 Signal Booster under FCC ID: PWO273201 in accordance with sections 0.457 and 0.459 of the Commission’s regulations. We request that the following documents be kept confidential: 1. Schematic Diagram & Parts List (4 pages), filename: 273201 Schematic Diagram & Parts List.pdf 2. Operational Description, filename: 273201 Operational Description.doc 3. Block Diagram, filename: 273201 Block Diagram.pdf The above material is confidential and contains proprietary trade secrets and technical data which must be kept from competitors. Public access to these items could result in duplication of our circuitry and/or techniques thereby reducing our competitive advantage and causing us severe damage. Sincerely, Richard M. Kline Senior Electrical Engineer

APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO273201 IC: 4726A-273201 EXTERNAL PHOTOS

APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO273201 IC: 4726A-273201 Label sample and location LABEL TO BE PLACED ON THE SIDE OF THE UNIT AS SEEN BELOW:

APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO273201 IC: 4726A-273201 INTERNAL PHOTOS

May 23, 2012 To: Whom it May Concern Subject: Final Amplification Stage Voltage and Current Please note that the maximum voltages and currents for the four final amplification stages of the Model 273201 Signal Booster are: Uplink Amplifier (824-849 MHz): 4.5 V, 0.6 A Downlink Amplifier (869-894 MHz): 3.6 V, 0.06 A Uplink Amplifier (1850-1910 MHz): 4.5 V, 0.6 A Downlink Amplifier (1930-1990 MHz): 3.6 V, 0.06 A Sincerely, Richard M. Kline Senior Electrical Engineer

May 23, 2012 Tuning and Adjustment of Wilson Model 273201 Signal Booster There are no external tuning or other adjustments. Sincerely, Richard M. Kline Senior Electrical Engineer

June 28, 2012 Subject: RF MPE EXPOSURE Re: FCC ID: PWO273201 To Whom It May Concern: The MPE calculations for model 273201 signal booster were done for each frequency band: 800 MHz and 1900 MHz. For each band three calculations were done; these included the different possibilities of antennas that may be connected to this signal booster: fixed outside, mobile outside, and inside antennas. The order of the attached calculations is as follows: 800 MHz band: 1. Fixed Outside Antenna 2. Mobile Outside Antenna 3. Inside Antenna 1900 MHz band: 4. Fixed Outside Antenna 5. Mobile Outside Antenna 6. Inside Antenna The results of these calculations determine the safe distances and gains for antennas that may be connected to this signal booster as explained in the user manual. Minimum Safe Distance From Antennas Based upon FCC OET Bulletin 65 and other FCC Sources INPUT DATA Frequency MHz824 Pout Watts1.04700 Duty Cycle Percent100.0% Ant. Gain dBi15.00 Coax Loss dB0.00 Evaluation Distance From Antenna In cm70.0 Ant. Gain less Coax Loss dBi15.00 Evaluation Distance From Antenna In Inches27.56 ERP (Watts)20.1884 EIRP (Watts)33.1090 FCC Limit at Above Frequency (mw/cm 2 ) 0.55 Calculated Power Density With Above Input Data (mw/cm 2 ) 0.54 REFERENCE DATA Pout dBm30.20 Antenna Gain (non-log)31.62 Coax loss (non-log)1.00 General FCC Limit (mw/cm 2 ) f/1500 For Amplifier Model Number: Frequency Band (MHz) Mobile or Fixed? Outside or Inside Antenna? Antenna Type: Safe Distance (inches): Signature: Date:May 23, 2012 cable loss does not exceed 15 dBi 824-849 MHz (Uplink) RESULTS OF CALCULATIONS SUMMARY FOR PUBLICATION 273201 Fixed Any antenna whose gain less Outside 28 inches 5/23/2012, 3:15 PM800 Fixed Outside Minimum Safe Distance From Antennas Based upon FCC OET Bulletin 65 and other FCC Sources INPUT DATA Frequency MHz824 Pout Watts1.04700 Duty Cycle Percent100.0% Ant. Gain dBi3.70 Coax Loss dB0.00 Evaluation Distance From Antenna In cm20.0 Ant. Gain less Coax Loss dBi3.70 Evaluation Distance From Antenna In Inches7.87 ERP (Watts)1.4966 EIRP (Watts)2.4544 FCC Limit at Above Frequency (mw/cm 2 ) 0.55 Calculated Power Density With Above Input Data (mw/cm 2 ) 0.49 REFERENCE DATA Pout dBm30.20 Antenna Gain (non-log)2.34 Coax loss (non-log)1.00 General FCC Limit (mw/cm 2 ) f/1500 For Amplifier Model Number: Frequency Band (MHz) Mobile or Fixed? Outside or Inside Antenna? Antenna Type: Safe Distance (inches): Signature: Date:May 23, 2012 cable loss does not exceed 2.3 dBi 824-849 MHz (Uplink) RESULTS OF CALCULATIONS SUMMARY FOR PUBLICATION 273201 Mobile Any antenna whose gain less Outside 8 inches 5/23/2012, 3:18 PM800 Mobile Outside Minimum Safe Distance From Antennas Based upon FCC OET Bulletin 65 and other FCC Sources INPUT DATA Frequency MHz869 Pout Watts0.00910 Duty Cycle Percent100.0% Ant. Gain dBi15.00 Coax Loss dB0.00 Evaluation Distance From Antenna In cm20.0 Ant. Gain less Coax Loss dBi15.00 Evaluation Distance From Antenna In Inches7.87 ERP (Watts)0.1755 EIRP (Watts)0.2878 FCC Limit at Above Frequency (mw/cm 2 ) 0.58 Calculated Power Density With Above Input Data (mw/cm 2 ) 0.06 REFERENCE DATA Pout dBm9.59 Antenna Gain (non-log)31.62 Coax loss (non-log)1.00 General FCC Limit (mw/cm 2 ) f/1500 For Amplifier Model Number: Frequency Band (MHz) Mobile or Fixed? Outside or Inside Antenna? Antenna Type: Safe Distance (inches): Signature: Date:May 23, 2012 cable loss does not exceed 15 dBi 869-894 MHz (Downlink) RESULTS OF CALCULATIONS SUMMARY FOR PUBLICATION 273201 Fixed/Mobile Any antenna whose gain less Inside 8 inches 5/23/2012, 3:16 PM800 Inside Minimum Safe Distance From Antennas Based upon FCC OET Bulletin 65 and other FCC Sources INPUT DATA Frequency MHz1850 Pout Watts1.17500 Duty Cycle Percent100.0% Ant. Gain dBi15.00 Coax Loss dB0.00 Evaluation Distance From Antenna In cm55.0 Ant. Gain less Coax Loss dBi15.00 Evaluation Distance From Antenna In Inches21.65 ERP (Watts)22.6566 EIRP (Watts)37.1568 FCC Limit at Above Frequency (mw/cm 2 ) 1.00 Calculated Power Density With Above Input Data (mw/cm 2 ) 0.98 REFERENCE DATA Pout dBm30.70 Antenna Gain (non-log)31.62 Coax loss (non-log)1.00 General FCC Limit (mw/cm 2 ) 1.00 For Amplifier Model Number: Frequency Band (MHz) Mobile or Fixed? Outside or Inside Antenna? Antenna Type: Safe Distance (inches): Signature: Date:May 23, 2012 cable loss does not exceed 15 dBi 1850-1910 MHz (Uplink) RESULTS OF CALCULATIONS SUMMARY FOR PUBLICATION 273201 Fixed Any antenna whose gain less Outside 28 inches 5/23/2012, 3:18 PM1900 Fixed Outside Minimum Safe Distance From Antennas Based upon FCC OET Bulletin 65 and other FCC Sources INPUT DATA Frequency MHz1850 Pout Watts1.17500 Duty Cycle Percent100.0% Ant. Gain dBi2.30 Coax Loss dB0.00 Evaluation Distance From Antenna In cm20.0 Ant. Gain less Coax Loss dBi2.30 Evaluation Distance From Antenna In Inches7.87 ERP (Watts)1.2167 EIRP (Watts)1.9954 FCC Limit at Above Frequency (mw/cm 2 ) 1.00 Calculated Power Density With Above Input Data (mw/cm 2 ) 0.40 REFERENCE DATA Pout dBm30.70 Antenna Gain (non-log)1.70 Coax loss (non-log)1.00 General FCC Limit (mw/cm 2 ) 1.00 For Amplifier Model Number: Frequency Band (MHz) Mobile or Fixed? Outside or Inside Antenna? Antenna Type: Safe Distance (inches): Signature: Date:May 23, 2012 cable loss does not exceed 2.3 dBi 1850-1910 MHz (Uplink) RESULTS OF CALCULATIONS SUMMARY FOR PUBLICATION 273201 Mobile Any antenna whose gain less Outside 8 inches 5/23/2012, 3:19 PM1900 Mobile Outside Minimum Safe Distance From Antennas Based upon FCC OET Bulletin 65 and other FCC Sources INPUT DATA Frequency MHz1930 Pout Watts0.00680 Duty Cycle Percent100.0% Ant. Gain dBi15.00 Coax Loss dB0.00 Evaluation Distance From Antenna In cm20.0 Ant. Gain less Coax Loss dBi15.00 Evaluation Distance From Antenna In Inches7.87 ERP (Watts)0.1311 EIRP (Watts)0.2150 FCC Limit at Above Frequency (mw/cm 2 ) 1.00 Calculated Power Density With Above Input Data (mw/cm 2 ) 0.04 REFERENCE DATA Pout dBm8.33 Antenna Gain (non-log)…

Text truncated - open the document above for the full version.

FCC PART 22H AND PART 24E TEST REPORT Applicant WILSON ELECTRONICS, INC. Address 3301 E. DESERET DRIVE ST. GEORGE UTAH 84790 USA FCC ID PWO273201 Model Number 273201 Product Description WIRELESS DUAL-BAND SIGNAL BOOSTER Date Sample Received 3/15/2012 Date Tested 4/26/2012 Tested By Nam Nguyen Approved By Mario de Aranzeta Report No. 662AUT12TestReport_for FCC.doc Test Results PASS FAIL THE ATTACHED REPORT SHALL NOT BE REPRODUCED EXCEPT IN FULL WITHOUT THE WRITTEN APPROVAL OF TIMCO ENGINEERING, INC. Test Certificate #0955-01 849 NW STATE ROAD 45 NEWBERRY, FL 32669 USA PH: 888.472.2424 OR 352.472.5500 FAX: 352.472.2030 EMAIL: [email protected] HTTP://WWW.TIMCOENGR.COM APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO273201 Report #: W\WILSON_PWO\662AUT12\662AUT12TestReport.doc Page 2 of 70 TABLE OF CONTENTS ATTESTATION STATEMENT ............................................................................ 3 REPORT SUMMARY ........................................................................................ 4 TEST ENVIRONMENT ..................................................................................... 4 TEST SETUP ................................................................................................... 4 DEVICE UNDER TEST INFORMATION ............................................................ 5 EQUIPMENT LIST ........................................................................................... 6 TEST PROCEDURE ......................................................................................... 7 RF POWER OUTPUT ..................................................................................... 10 Test Data Table 1 – Output Power – CDMA 1900 – Uplink/Downlink .................. 10 Test Data Table 2 – Output Power – HSPA 1900 – Uplink/Downlink ................... 10 Test Data Table 3 – Output Power – LTE 1900 – Uplink/Downlink ...................... 10 Test Data Table 4 – Output Power – GSM 1900 – Uplink/Downlink .................... 10 Test Data Table 5 – Output Power – EDGE 1900 – Uplink/Downlink .................. 11 Test Data Table 6 – Output Power – CDMA 800 – Uplink/Downlink .................... 11 Test Data Table 7 – Output Power – HSPA 800 – Uplink/Downlink ..................... 11 Test Data Table 8 – Output Power – LTE 800 – Uplink/Downlink ........................ 11 Test Data Table 9 – Output Power – GSM 800 – Uplink/Downlink ...................... 11 Test Data Table 10 – Output Power – EDGE 800 – Uplink/Downlink .................. 12 INPUT/OUTPUT MODULATED AMPLITUDE COMPARISON AND BAND-EDGES COMPLIANCE ............................................................................................... 13 Test Data Table 11 – CDMA 1900 – Uplink/Downlink ......................................... 14 Test Data Table 12 – HSPA 1900 – Uplink/Downlink .......................................... 18 Test Data Table 13 – LTE 1900 – Uplink/Downlink ............................................ 22 Test Data Table 14 –GSM 1900 – Uplink/Downlink ............................................ 26 Test Data Table 15 – EDGE 1900 – Uplink/Downlink ......................................... 30 Test Data Table 16 – CDMA 800 – Uplink/Downlink ........................................... 34 Test Data Table 17 – HSPA 800 – Uplink/Downlink ............................................ 38 Test Data Table 18 – LTE 800 – Uplink/Downlink .............................................. 42 Test Data Table 19 – GSM 800 – Uplink/Downlink ............................................. 46 Test Data Table 20 – EDGE 800 – Uplink/Downlink ........................................... 50 INTERMODULATION PRODUCT SPURIOUS EMISSIONS ............................... 54 SPURIOUS EMISSIONS AT ANTENNA TERMINALS ........................................ 62 Test Data Table 21 – Conducted Emissions – CDMA 1900 – Uplink .................... 62 Test Data Table 22 – Conducted Emissions – CDMA 1900 – Downlink ................ 62 Test Data Table 23 – Conducted Emissions – GSM 1900 - Uplink ....................... 63 Test Data Table 24 – Conducted Emissions – GSM 1900 - Downlink ................... 63 Test Data Table 25 – Conducted Emissions – CDMA 800 - Uplink ...................... 63 Test Data Table 26 – Conducted Emissions – CDMA 800 - Downlink .................. 64 Test Data Table 27 – Conducted Emissions – GSM 800 – Uplink ......................... 64 Test Data Table 28 – Conducted Emissions – GSM 800 - Downlink ..................... 64 FIELD STRENGTH OF SPURIOUS EMISSIONS .............................................. 65 Test Data Table 29 – Radiated Emissions – CW (1900 MHz) – Uplink /Downlink . 65 Test Data Table 30 – Radiated Emissions – CW (800 MHz) – Uplink /Downlink ... 66 OUT OF BAND REJECTION: FREQUENCY RESPONSE ................................. 67 APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO273201 Report #: W\WILSON_PWO\662AUT12\662AUT12TestReport.doc Page 3 of 70 ATTESTATION STATEMENT Summary The device under test does: fulfill the general approval requirements as identified in this test report not fulfill the general approval requirements as identified in this test report This equipment has been tested in accordance with the standards identified in this test report. To the best of my knowledge and belief, these tests were performed using the measurement procedures described in this report. All instrumentation and accessories used to test products for compliance to the indicated standards are calibrated regularly in accordance with ISO 17025: 2005 requirements. Certificate # 0955-01 I attest that the necessary measurements were made, under my supervision, at TIMCO ENGINEERING, INC. located at 849 N.W. State Road 45, Newberry, Florida 32669. Authorized Signatory Name: Mario de Aranzeta Signature: Function: Engineer Date: 5/4/2012 APPLICANT: WILSON ELECTRONICS, INC. FCC ID: PWO273201 Report #: W\WILSON_PWO\662AUT12\662AUT12TestReport.doc Page 4 of 70 REPORT SUMMARY Disclaimer The test results relate on…

Text truncated - open the document above for the full version.