PWO274080iDEN 800MHz Signal Booster

Contents: Antenna Options & Accessories . . . . . . . . . . . . . . . . . . . . . . .1 Quick Install Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Installation Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Before Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Outside Antenna Installation . . . . . . . . . . . . . . . . . . . . . . . . . .5 Finding the Strongest Signal . . . . . . . . . . . . . . . . . . . . . . . . . .6 Installing the Inside Antenna . . . . . . . . . . . . . . . . . . . . . . . . . .8 Installing a Wilson Electronics Signal Booster . . . . . . . . . . . . . 9 Powering up a Wilson Electronics Signal Booster . . . . . . . . . .9 Understanding the Signal Booster Light . . . . . . . . . . . . . . . .10 Warnings and Recommendations . . . . . . . . . . . . . . . . . . . . .12 Guarantee & Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover Note: This manual contains important safety and operating information . Please read and follow the instructions in this manual . Failure to do so could be hazardous and result in damage to your Signal Booster . iDEN 800 MHz Adjustable Gain In-Building Wireless Smart Technology ™ Signal Booster Appearance of device and accessories may vary . 1 Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: [email protected]. Mon.- Fri. Hours: 7 am to 6 pm MST. 2 Installation Instructions for the Following Wilson Electronics Signal Booster: iDEN 800 MHz Adjustable Gain In-Building Wireless Smart Technology ™ Signal Booster How it Works Wilson Electronics Signal Boosters are bi-directional devices that deliver service levels consistent with what would be expected in areas of high cell network coverage . They amplify a weak or shadowed signal in mobile, M2M, marine and in-building applications . When using a Wilson Electronics Signal Booster in conjunction with Wilson Electronics antennas, the Outside Antenna will collect the cell tower signal and send it through the cable to the Signal Booster . The signal is then amplified and re-transmitted through the Inside Antenna into the room . Cell phones and cellular data cards in that area then communicate with the improved signal . When a cell phone or cellular device transmits, the signal is received by the Inside Antenna, amplified by the Signal Booster and transmitted back to the cell tower through the Outside Antenna . Inside this Package Signal Booster 7V AC/DC Power Supply (included in some kits) To purchase, call Wilson Electronics Sales Department at: 800-204-4104 Outdoor Antenna Options Indoor Antenna Options & Accessories 1 . 800 MHz Yagi Antenna (301111) 2 . 800 MHz Yagi Cellular Antenna (301129) 3 . Wide Band Directional Antenna 700 - 2700 MHz (304411) 4 . Outdoor Panel Antenna 700-2700 MHz (301157) A . Wide-Band Panel Antenna 700-2700MHz (301134 & 301135) B . 50 Ohm Lightning Surge Protector with N-Connectors (859902) Splitter options on page 8 3 1 2 B A 4 Note: Kits may contain different accessories Appearance of device and accessories may vary . Model #274080 FCC ID: PWO274080 IC: 4726A-274080 1 2 Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: [email protected]. Mon. -Fri. Hours: 7 am to 6 pm MST. Select a location to install the Signal Booster that is away from 1 . excessive heat, direct sunlight, moisture and has proper ventilation . Do not place the Signal Booster in an air-tight enclosure . Select a location on the roof of the building to install the Outside 2 . Antenna (see page 5) . Use a cell phone in test mode to find the strongest signal from the cell tower . (see page 6) . Visit www.WilsonElectronics.com to find the test mode function for your particular cell phone . Run the Outside Antenna cable to the Signal Booster and attach it to 3 . the connector labeled “Outside Antenna” on the Signal Booster . Run the Inside Antenna cable to the Signal Booster and attach it to the connector labeled “Inside Antenna” on the Signal Booster . See page 7 for more information on running cable . Lightning Surge Protection is recommended for all in-building installations (see page 6) . Select a location for the Inside Antenna, preferably in the center of 4 . where the signal needs to be amplified (see page 8) . A minimum separation distance of 20 vertical feet is necessary for operation . If the inside coverage is not sufficient you may need as much as 75 feet of horizontal separation . See installation diagram on pages 3 & 4 . Before powering up the Signal Booster, verify that both the Outside 5 . Antenna and the Inside Antenna are connected and check that all connections are tight (see page 9) . Note: Be careful when plugging the connectors in so as not to bend the center pins on the connectors. The Signal Booster has been packaged with the gain control knobs 6 . adjusted to the highest gain position . If the light is not green, please refer to pages 10-11 . Quick Install Overview See Installation Diagram on page 3 . Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 . Warning: Connecting the Signal Booster directly to a cell phone with use of an adapter will damage the cell phone and/or the Signal Booster . IMPORTANT NOTICE It is very important to power your Signal Booster using a • surge protected AC Power Strip with at least a 1000 Joule rating. Failure to do this will void your warranty in the • event of a power surge or lightning strike . 3 Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: [email protected]. Mon.- Fri. Hours: 7 am to 6 pm MST. 4 Typical Installation Outside Antenna (Yagi option shown) Cell Tower Inside Antenna Installation Diagram Note: The Inside Antenna may be mounted on the wall directly under the Out…

Text truncated - open the document above for the full version.

Wilson Electronics, Inc. FCC ID: PWO274080 Report Number: R1109072-90 Page 89 of 92 FCC Part 90 Test Report 11 EXHIBIT B - EUT PHOTOGRAPHS 11.1 EUT - Front View 11.2 EUT - Bottom View Wilson Electronics, Inc. FCC ID: PWO274080 Report Number: R1109072-90 Page 90 of 92 FCC Part 90 Test Report 11.3 EUT - Side View 1 11.4 EUT - Side View 2 11.5 EUT – Inside Antenna Port View 11.6 EUT – Outside Antenna Port View

Wilson Electronics, Inc. FCC ID: PWO274080 Report Number: R1109072-90 Page 91 of 92 FCC Part 90 Test Report 11.7 EUT – Cover off View 11.8 EUT – Main PCB Board Front View Wilson Electronics, Inc. FCC ID: PWO274080 Report Number: R1109072-90 Page 92 of 92 FCC Part 90 Test Report 11.9 EUT – Main PCB Board Rear View 11.10 AC/DC Power Supply View ---End of Report---

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, NIST, or any agency of the Federal Government. * This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “*” (Rev.2) FCC PART 90 TEST AND MEASUREMENT REPORT For Wilson Electronics, Inc. 3301 East Deseret Drive, St. George, Utah 84790, USA FCC ID:PWO274080 Report Type: Original Report Product Type: Signal Booster Test Engineer: Quinn Jiang Report Number: R1109072-90 Report Date: 2012-05-21 Reviewed By: Victor Zhang EMC/RF Lead Prepared By: (RZ) Bay Area Compliance Laboratories Corp. 1274 Anvilwood Avenue, Sunnyvale, CA 94089, USA Tel: (408) 732-9162 Fax: (408) 732 9164 Wilson Electronics, Inc. FCC ID: PWO274080 Report Number: R1109072-90 Page 2 of 92 FCC Part 90 Test Report TABLE OF CONTENTS 1 GENERAL INFORMATION.............................................................................................................................. 5 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)........................................................................ 5 1.2 MECHANICAL DESCRIPTION........................................................................................................................... 5 1.3 OBJECTIVE...................................................................................................................................................... 5 1.4 RELATED SUBMITTAL(S)/GRANT(S) ............................................................................................................... 5 1.5 TEST METHODOLOGY..................................................................................................................................... 6 1.6 MEASUREMENT UNCERTAINTY...................................................................................................................... 6 1.7 TEST FACILITY............................................................................................................................................... 6 2 SYSTEM TEST CONFIGURATION ................................................................................................................. 7 2.1 JUSTIFICATION................................................................................................................................................ 7 2.2 EUT EXERCISE SOFTWARE............................................................................................................................. 7 2.3 EQUIPMENT MODIFICATIONS.......................................................................................................................... 7 2.4 LOCAL SUPPORT EQUIPMENT AND SOFTWARE LIST AND DETAILS................................................................. 7 2.5 EUT INTERNAL CONFIGURATION................................................................................................................... 7 2.6 INTERFACE PORTS AND CABLES..................................................................................................................... 7 3 SUMMARY OF TEST RESULTS ...................................................................................................................... 8 4 FCC §2.1046 & §90.205 – RF OUTPUT POWER ............................................................................................. 9 4.1 APPLICABLE STANDARD................................................................................................................................. 9 4.2 TEST PROCEDURE........................................................................................................................................... 9 4.3 TEST SETUP BLOCK DIAGRAM........................................................................................................................ 9 4.4 TEST EQUIPMENT LIST AND DETAILS............................................................................................................. 9 4.5 TEST ENVIRONMENTAL CONDITIONS............................................................................................................ 10 4.6 TEST RESULTS.............................................................................................................................................. 10 5 FCC §2.1047 - MODULATION CHARACTERISTIC ................................................................................... 12 5.1 APPLICABLE STANDARD...............................................................................................................................12 5.2 TEST RESULT................................................................................................................................................ 12 6 FCC §2.1049 & §90.209 – OCCUPIED BANDWIDTH .................................................................................. 13 6.1 APPLICABLE STANDARD...............................................................................................................................13 6.2 TEST PROCEDURE......................................................................................................................................... 13 6.3 TEST EQUIPMENT LIST AND DETAILS........................................................................................................... 13 6.4 TEST ENVIRONMENTAL CONDITIONS............................................................................................................ 13 6.5 TEST RESULTS.............................................................................................................................................. 13 7 FCC §2.1049, §90.210 & §90.961 – EMISSION MASK ...........................................................................…

Text truncated - open the document above for the full version.

Wilson Electronics, Inc. FCC ID: PWO274080 Report Number: R1109072-90 Page 87 of 92 FCC Part 90 Test Report 10 EXHIBIT A - TEST SETUP PHOTOGRAPHS 10.1 Radiated Emissions - Front View 10.2 Radiated Emissions 30 MHz to 1 GHz- Rear View Wilson Electronics, Inc. FCC ID: PWO274080 Report Number: R1109072-90 Page 88 of 92 FCC Part 90 Test Report 10.3 Radiated Emissions above 1 GHz- Rear View 10.4 Conducted Measurement View