PWO460006Model 460006 Signal Booster

Contents: Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 How it Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Vehicle Installation Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Install the Outside Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Power up the Wilson Electronics Sleek . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Adjusting the Sleek Arms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Understanding the Sleek Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 In-Building Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 About Wilson Electronics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Signal Booster Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover To boost your phone’s signal power, the phone must be placed in the Sleek cradle . For best results, use a Bluetooth ® headset or hands free device, while the phone remains in the Sleek . Dual-Band SmarTech ™ Booster Appearance of device and accessories may vary . Note: This manual contains important safety and operating information . Please read and follow the instructions in this manual . Failure to do so could be hazardous and result in damage to your Sleek . ® U .S . Patent Nos . – D626,953; 7,684,838; 7,221,967; 7,729,669; 7,486,929; 7,729,656; 7,409,186; 7,783,318 1 Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: [email protected]. Mon.- Fri. Hours: 7 am to 6 pm MST. AC Power Supply *(859969) Gooseneck Suction Cup Cradle Mount (901120) Cup Holder Cradle Mount (901130) Adjustable Desk Mount *(901137) Accessories for your Sleek ® Mobile Antennas Antenna Window Mount (Used with Mini-Magnet Mount Antenna) *(901128) Mini-Magnet Mount Antenna (301126) Vehicle Dash Adhesive Mounting Bracket DC Plug-In Power Supply & USB cable (859963) Sleek ® Vehicle Dash Mounting Kit -Rugged/Screw Mount- -Adhesive Mount- -Vent Clip Mount- (901134 ) (included in some kits) * All 3 available together in the Home Accessory Kit - 859970 Adjustable Arms Carrying case included Appearance of device and accessories may vary . (This product is not marketed by Verizon Wireless or AT&T) . Mobile Power Supply (859984) Inside this Package Sleek ® 800 / 1900 MHz Model #460006 FCC: PWO460006 IC: 4726A-460006 The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. FCC requires to never use the cell phone in the cradle next to your ear . Mini-Mag • 301126 w/ 12.5 RG174 cable- SMA • 301113 w/ 12.5 RG174 cable - FME 12” Mag Mount w/ 12.5’ RG174 • 311103 • 311125 • 311128 • 311703 • 314202 Trucker antenna w/10.5’ RG58 • 311101 • 311701 Trucker antenna w/13.5’ RG58 • 311119 • 311133 NMO Antenna’s w/ RG174 Kit 311104-17410 • 800/1900 NMO antenna • 10’ RG174 cable Kit 311112-17410 • 800/1900 NMO antenna • 10’ RG174 cable Kit 314203-17410 • 800/900/1900 NMO antenna • 10’ RG174 cable Marine Antenna w/ RG58 Kit 311130-5810 • Marine Antenna • 10’ RG58 cable Glass Mount w/14’ RG58 cable • 311102 • 311114 ( Mini Glass Mount) NMO Antenna’s w/ RG58 Kit 311104-5810 • 800/1900 NMO antenna • 10’ RG58 cable Kit 311112-5810 • 800/1900 NMO antenna • 10’ RG58 cable Kit 314203-5810 • 800/900/1900 NMO antenna • 10’ RG58 cable NMO Antenna’s w/ LMR400 Kit 311104-40015 • 800/1900 NMO antenna • 15’ LMR400 cable Kit 311112-40015 • 800/1900 NMO antenna • 15’ LMR400 cable Kit 314203-40015 • 800/900/1900 NMO antenna • 15’ LMR400 cable Outside Fixed Antennas 50 Ohm Outside Antenna Kits Kit 314453-5825 • 50 Ohm Pole Mount Panel Antenna • 25’ RG58 Cable Kit 314411-5825 • 50 Ohm Wide Band Directional • 25’ RG58 Cable Kit 301111-5850 • Yagi Directional Antenna • 50’ RG58 Cable Kit 311124-5840 • 1900 MHz Yagi Directional • 40’ RG58 Cable Kit 311203-5820 • Omni-Directional antenna • 20’ RG58 Cable Kit 311129-5830 • 800 MHz Yagi Antenna • 30’ RG58 Cable Kit 314411-40075 • 50 Ohm Wide Band Directional • 75’ LMR400 Cable Kit 311203-40020 • Omni-Directional antenna • 20’ LMR400 Cable Kit 301111-400170 • Yagi Directional w/ N-Female • 170’ LMR400 Kit 311124-400100 • 1900 MHz Yagi Directional • 100’ LMR400 Cable Kit 311129-400100 • 800 MHz Yagi Antenna • 100’ LMR400 Cable Kit 314453-40075 • 50 Ohm Pole Mount Panel Antenna • 75’ LMR400 Cable 75 Ohm Outside Antenna Kits Kit 301111-0675 • Yagi Directional Antenna • 75’ RG6 Cable • N-Male to F-Female adapter Kit 311201-0620 • Omni Directional w/ F-Female • 20’ RG6 Cable Kit 311124-0660 • 1900 MHz Yagi Directional • 60’ RG6 Cable • N-Male to F-Female adapter Kit 311129-0650 • 800 MHz Yagi Directional • 50’ RG6 Cable • N-Male to F-Female adapter Kit 314473-0640 • 75 Ohm Pole Mount Panel Antenna • 40’ RG6 Cable Kit 314475-0630 • 75 Ohm Wide Band Directional • 30’ RG6 Cable Kit 311141-0620 • 75 Ohm Grey Brick Antenna • 20’ RG6 Cable Kit 301111-11140 • Yagi Directional Antenna • 140’ RG11 Cable • N-Male to F-Female adapter Kit 311201-1120 • Omni Directional w/ F-Female • 20’ RG11 Cable Kit 311124-1…

Text truncated - open the document above for the full version.

Contents: Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 How it Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Vehicle Installation Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Install the Outside Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Power up the Wilson Electronics Sleek . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Adjusting the Sleek Arms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Understanding the Sleek Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 In-Building Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 About Wilson Electronics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Signal Booster Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover To boost your phone’s signal power, the phone must be placed in the Sleek cradle . For best results, use a Bluetooth ® headset or hands free device, while the phone remains in the Sleek . Dual-Band SmarTech ™ Booster Appearance of device and accessories may vary . Note: This manual contains important safety and operating information . Please read and follow the instructions in this manual . Failure to do so could be hazardous and result in damage to your Sleek . ® U .S . Patent Nos . – D626,953; 7,684,838; 7,221,967; 7,729,669; 7,486,929; 7,729,656; 7,409,186; 7,783,318 1 Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: [email protected]. Mon.- Fri. Hours: 7 am to 6 pm MST. AC Power Supply *(859969) Gooseneck Suction Cup Cradle Mount (901120) Cup Holder Cradle Mount (901130) Adjustable Desk Mount *(901137) Accessories for your Sleek ® Mobile Antennas Antenna Window Mount (Used with Mini-Magnet Mount Antenna) *(901128) Mini-Magnet Mount Antenna (301126) Vehicle Dash Adhesive Mounting Bracket DC Plug-In Power Supply & USB cable (859963) Sleek ® Vehicle Dash Mounting Kit -Rugged/Screw Mount- -Adhesive Mount- -Vent Clip Mount- (901134 ) (included in some kits) * All 3 available together in the Home Accessory Kit - 859970 Adjustable Arms Carrying case included Appearance of device and accessories may vary . (This product is not marketed by Verizon Wireless or AT&T) . Mobile Power Supply (859984) Inside this Package Sleek ® 800 / 1900 MHz Model #460006 FCC: PWO460006 IC: 4726A-460006 The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. FCC requires to never use the cell phone in the cradle next to your ear . Mini-Mag • 301126 w/ 12.5 RG174 cable- SMA • 301113 w/ 12.5 RG174 cable - FME 12” Mag Mount w/ 12.5’ RG174 • 311103 • 311125 • 311128 • 311703 • 314202 Trucker antenna w/10.5’ RG58 • 311101 • 311701 Trucker antenna w/13.5’ RG58 • 311119 • 311133 NMO Antenna’s w/ RG174 Kit 311104-17410 • 800/1900 NMO antenna • 10’ RG174 cable Kit 311112-17410 • 800/1900 NMO antenna • 10’ RG174 cable Kit 314203-17410 • 800/900/1900 NMO antenna • 10’ RG174 cable Marine Antenna w/ RG58 Kit 311130-5810 • Marine Antenna • 10’ RG58 cable Glass Mount w/14’ RG58 cable • 311102 • 311114 ( Mini Glass Mount) NMO Antenna’s w/ RG58 Kit 311104-5810 • 800/1900 NMO antenna • 10’ RG58 cable Kit 311112-5810 • 800/1900 NMO antenna • 10’ RG58 cable Kit 314203-5810 • 800/900/1900 NMO antenna • 10’ RG58 cable NMO Antenna’s w/ LMR400 Kit 311104-40015 • 800/1900 NMO antenna • 15’ LMR400 cable Kit 311112-40015 • 800/1900 NMO antenna • 15’ LMR400 cable Kit 314203-40015 • 800/900/1900 NMO antenna • 15’ LMR400 cable Outside Fixed Antennas 50 Ohm Outside Antenna Kits Kit 314453-5825 • 50 Ohm Pole Mount Panel Antenna • 25’ RG58 Cable Kit 314411-5825 • 50 Ohm Wide Band Directional • 25’ RG58 Cable Kit 301111-5850 • Yagi Directional Antenna • 50’ RG58 Cable Kit 311124-5840 • 1900 MHz Yagi Directional • 40’ RG58 Cable Kit 311203-5820 • Omni-Directional antenna • 20’ RG58 Cable Kit 311129-5830 • 800 MHz Yagi Antenna • 30’ RG58 Cable Kit 314411-40075 • 50 Ohm Wide Band Directional • 75’ LMR400 Cable Kit 311203-40020 • Omni-Directional antenna • 20’ LMR400 Cable Kit 301111-400170 • Yagi Directional w/ N-Female • 170’ LMR400 Kit 311124-400100 • 1900 MHz Yagi Directional • 100’ LMR400 Cable Kit 311129-400100 • 800 MHz Yagi Antenna • 100’ LMR400 Cable Kit 314453-40075 • 50 Ohm Pole Mount Panel Antenna • 75’ LMR400 Cable 75 Ohm Outside Antenna Kits Kit 301111-0675 • Yagi Directional Antenna • 75’ RG6 Cable • N-Male to F-Female adapter Kit 311201-0620 • Omni Directional w/ F-Female • 20’ RG6 Cable Kit 311124-0660 • 1900 MHz Yagi Directional • 60’ RG6 Cable • N-Male to F-Female adapter Kit 311129-0650 • 800 MHz Yagi Directional • 50’ RG6 Cable • N-Male to F-Female adapter Kit 314473-0640 • 75 Ohm Pole Mount Panel Antenna • 40’ RG6 Cable Kit 314475-0630 • 75 Ohm Wide Band Directional • 30’ RG6 Cable Kit 311141-0620 • 75 Ohm Grey Brick Antenna • 20’ RG6 Cable Kit 301111-11140 • Yagi Directional Antenna • 140’ RG11 Cable • N-Male to F-Female adapter Kit 311201-1120 • Omni Directional w/ F-Female • 20’ RG11 Cable Kit 311124-1…

Text truncated - open the document above for the full version.

November 27, 2013 Attestation For Wilson Signal Booster: FCC ID PWO460006 Each Signal Booster certificated under FCC ID PWO460006 is manufactured and individually tested to ensure FCC compliance: (1) Since this is not a provider-specific booster, licensee consent is not required. (2) NPS and other compliance/safeguard features have been implemented. (3) NPS and other compliance/safeguard features are defaulted to be “On” (in operation). (4) NPS and other compliance/safeguard features cannot be field reconfigured, disabled, or removed. (5) This consumer booster is not user programmable, does not need fine tuning or adjustment, and does not require professional installation. (6) Future software upgrade will not cause non-compliance. Sincerely, Patrick L. Cook Senior Research and Development Engineer

November 27, 2013 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Data Confidentiality To Whom It May Concern: Wilson Electronics, Inc. respectfully requests confidentiality of certain documentation provided with the submission of our model 460006 Signal Booster under FCC ID: PWO460006 in accordance with sections 0.457 and 0.459 of the Commission’s regulations. We request that the following documents be kept confidential: 1. Schematic Diagram & Parts List 2. Operational Description 3. Block Diagram 4. Antenna Measurements and Testing Data The above material is confidential and contains proprietary trade secrets and technical data which must be kept from competitors. Public access to these items could result in duplication of our circuitry and/or techniques thereby reducing our competitive advantage and causing us severe damage. Sincerely, Patrick L. Cook Senior Research and Development Engineer

November 27, 2013 To: Whom it May Concern Subject: Final Amplification Stage Voltage and Current Please note that the maximum voltages and currents for the final amplification stages of the Model 460006 Signal Booster are: Uplink Amplifier (824-849 MHz): 4.3 V, 0.5 A Downlink Amplifier (869-894 MHz): 4.3 V, 0.5 A Uplink Amplifier (1850-1910 MHz): 4.3 V, 0.5 A Downlink Amplifier (1930-1990 MHz): 4.3 V, 0.5 A Patrick L. Cook Senior Research and Development Engineer

November 27, 2013 To: Whom it May Concern Subject: Alternative Warning Label Placement This letter is to request alternative warning label placement for the signal booster model number 460006. The signal booster is too small to fit the warning label as can be seen from the Label Placement and External Photos exhibits. Instead, the warning can be found on page 6 of the User Manual. Sincerely, Patrick L. Cook Senior Research and Development Engineer

Page 1 of 1 FCC ID: PWO460006 IC ID: CT Project: P1350026 From: John Erhard Date: December 2, 2013 1. No test setup photos were provided. CT – Test Photos exhibit provided. 2. Note to laboratory – Not all OOBE plots have the full 100 averages. The plots clearly show the EUT complies and additional averages will only show additional margin to the limit. There is no additional action necessary as this is an advisory notice. CT - Noted Response by: Jennifer Sanchez Submitted by: Jennifer Sanchez Date: 12-4-13

Page 1 of 2 From: Axel Rodriguez [email protected] Re: FCC ID: PWO460006 Applicant: Wilson Electronics, LLC Correspondence Reference Number: 166313 Form 731 Confirmation Number: TC371891 Date of Original E-mail: 02/10/2014 1) Concerning the 20.21(f)(1)(4)(i) statement and label text requirement, FCC requests that the same words and the same uppercase and lowercase lettering scheme as shown in the rules shall be used for the label; please provide updated exhibit. Wilson - According to Title 47 Part 2.925(f): Where it is shown that a permanently affixed nameplate is not desirable or is not feasible, an alternative method of positively identifying the equipment may be used if approved by the Commission. The proposed alternative method of identification and the justification for its use must be included with the application for equipment authorization. The devise is too small for the requested label to fit on the device, rendering a permanently affixed label infeasible. The proposed alternative and justification was included with the application as seen on three exhibits: Cover Letter_Alternative Warning Label Placement, Label & Location, and External Photos. Attached are copies of those exhibits. Alternatively I have included a file with images of the PWO460006 with the required label. It is obvious from these images that the label does not fit. 2) Per 20.21(f)(1)(2), the 20.21(f)(1)(4)(i) statement must also be in the users' manual; please provide updated exhibit. Wilson - The updated user manual exhibit is also attached with the required information. Response by: Wilson Electronics Submitted by: CTL Date: 2/14/14

Page 1 of 1 From: Axel Rodriguez [email protected] Re: FCC ID: PWO460006 Applicant: Wilson Electronics, LLC Correspondence Reference Number: 166432 Form 731 Confirmation Number: TC371891 Date of Original E-mail: 02/11/2014 During our verification testing of this device we have found that it does not comply with section §20.21(e)(8)(ii)(A) Anti-Oscillation. Upon detecting oscillation, the booster is required to continue mitigation for at least one minute before restarting. In our testing we have observed that this booster upon detecting oscillation restarts after only 5 seconds. Please explain. Wilson - The problem that occurred here is that the booster with the 5 second delay was shipped rather than the one with the 60 second delay. As recommended by the KDB there were two models sent for testing. The one that was shipped to the FCC for sample testing was the wrong one. The one with the 60 second delay is in transit and should arrive at the FCC by 2/12/2014. Response by: Wilson Electronics Submitted by: CTL Date: 2/14/14

November 21, 2013 Subject: Antenna Kitting Re: FCC ID: PWO460006 To Whom It May Concern: The antenna kitting options for model 460006 signal booster were done for 19 Mobile Outside Antenna kit options, 27 Fixed Outside Antenna kit options, and no Inside Antenna kit options. The Inside Antenna kits are not applicable for model 460006 due to an inside antenna integrated into the Signal Booster. The order of the attached calculations is as follows: Mobile Outside Antenna Kit Options: 1. Kits 311103, 311125, 311128, 314202 2. Kit 311703 3. Kit 301113, 301126 4. Kit 311101 5. Kit 311701 6. Kit 311119 7. Kit 311133 8. Kit 311104-17410 9. Kit 311112-17410 10. Kit 314203-17410 11. Kit 311130-5810 12. Kit 311114 13. Kit 311102 14. Kit 311104-5810 15. Kit 311112-5810 16. Kit 314203-5810 17. Kit 311104-40015 18. Kit 311112-40015 19. Kit 314203-40015 Fixed Outside Antenna Kit Options: 1. Kit 314411-40075 2. Kit 314411-5825 3. Kit 314775-0630 4. Kit 301111-0675 5. Kit 301111-5850 6. Kit 311124-400100 7. Kit 311124-5840 8. Kit 311124-0660 9. Kit 311129-0650 10. Kit 311129-400100 11. Kit 311203-40020 12. Kit 311203-5820 13. Kit 311201-0620 14. Kit 301126 15. Kit 301111-11140 16. Kit 314453-5825 17. Kit 314453-40075 18. Kit 314473-0640 19. Kit 311141-0620 20. Kit 311129-1180 21. Kit 311201-1120 22. Kit 311124-11110 23. Kit 314475-1175 24. Kit 301111-400170 25. Kit 311141-1120 26. Kit 314473-1175 27. Kit 311129-5830 Sincerely, Patrick L. Cook Senior Research and Development Engineer FCC ID:460006 Final Output Power Limited to 30 dBm EIRP in all frequency bands Uplink Frequency (MHz)824-8491850-1910 Uplink Output Power (dBm)22.8625.15 1Magnet Mount w/12.5' RG-174311128311128311103311125 Antenna Gains (dBi)1.972.51 Coax Loss (dB)3.74.7 Final Gain less Loss (dB)-1.7-2.2 Output Power plus Final Gain (dBm EIRP)21.1323.0 2Magnet Mount w/12.5' RG-174311703 Antenna Gains (dBi)0.691.13 Coax Loss (dB)3.74.7 Final Gain less Loss (dB)-3.0-3.6 Output Power plus Final Gain (dBm EIRP)19.8521.58 3Mini-Mag Mount w/12.5' RG-174301126301113 Antenna Gains (dBi)-1.921.85 Coax Loss (dB)3.74.7 Final Gain less Loss (dB)-5.6-2.9 Output Power plus Final Gain (dBm EIRP)17.2422.3 4Trucker Antenna w/10.5' RG-58311101 Antenna Gains (dBi)1.726.12 Coax Loss (dB)1.42.3 Final Gain less Loss (dB)0.33.8 Output Power plus Final Gain (dBm EIRP)23.229.0 5Trucker Antenna w/10.5' RG-58311701 Antenna Gains (dBi)2.182.66 Coax Loss (dB)1.42.3 Final Gain less Loss (dB)0.80.4 Output Power plus Final Gain (dBm EIRP)23.6425.5 6Trucker Antenna w/13.5' RG-58311119 Antenna Gains (dBi)1.213.57 Coax Loss (dB)1.72.9 Final Gain less Loss (dB)-0.50.7 Output Power plus Final Gain (dBm EIRP)22.3725.82 7Trucker Antenna w/13.5' RG-58311133 Antenna Gains (dBi)1.154.22 Coax Loss (dB)1.72.9 Final Gain less Loss (dB)-0.61.3 Output Power plus Final Gain (dBm EIRP)22.326.5 8NMO Antenna 10' RG-174311104-17410 Antenna Gains (dBi)2.481.8 Coax Loss (dB)3.03.8 Final Gain less Loss (dB)-0.5-2.0 Output Power plus Final Gain (dBm EIRP)22.3423.15 9NMO Antenna 10' RG-174311112-17410 Antenna Gains (dBi)2.47-0.65 Coax Loss (dB)3.03.8 Final Gain less Loss (dB)-0.5-4.5 Output Power plus Final Gain (dBm EIRP)22.3320.7 10NMO Antenna 10' RG-174314203-17410 Antenna Gains (dBi)1.820.75 Coax Loss (dB)3.03.8 Final Gain less Loss (dB)-1.2-3.1 Output Power plus Final Gain (dBm EIRP)21.722.1 Mobile Outside Antenna Kit Options FCC ID:460006 Final Output Power Limited to 30 dBm EIRP in all frequency bands Uplink Frequency (MHz)824-8491850-1910 Uplink Output Power (dBm)22.8625.15 11Marine Antenna w/10' RG-58311130-5810 Antenna Gains (dBi)0.653.57 Coax Loss (dB)1.32.1 Final Gain less Loss (dB)-0.61.4 Output Power plus Final Gain (dBm EIRP)22.226.6 12Mini-Glass Mount w/14' RG-58311114 Antenna Gains (dBi)-5.391.44 Coax Loss (dB)1.83.0 Final Gain less Loss (dB)-7.2-1.6 Output Power plus Final Gain (dBm EIRP)15.723.6 13Glass Mount w/14' RG-58311102 Antenna Gains (dBi)-0.863.39 Coax Loss (dB)1.83.0 Final Gain less Loss (dB)-2.70.4 Output Power plus Final Gain (dBm EIRP)20.225.5 14NMO Antenna w/10' RG-58311104-5810 Antenna Gains (dBi)2.481.8 Coax Loss (dB)1.32.1 Final Gain less Loss (dB)1.2-0.3 Output Power plus Final Gain (dBm EIRP)24.0424.85 15NMO Antenna w/10' RG-58311112-5810 Antenna Gains (dBi)2.47-0.65 Coax Loss (dB)1.32.1 Final Gain less Loss (dB)1.2-2.8 Output Power plus Final Gain (dBm EIRP)24.0322.4 16NMO Antenna w/10' RG-58314203-5810 Antenna Gains (dBi)1.820.75 Coax Loss (dB)1.32.1 Final Gain less Loss (dB)0.5-1.4 Output Power plus Final Gain (dBm EIRP)23.423.8 17NMO Antenna w/15'LMR 400311104-40015 Antenna Gains (dBi)2.481.8 Coax Loss (dB)0.91.3 Final Gain less Loss (dB)1.580.5 Output Power plus Final Gain (dBm EIRP)24.425.7 18NMO Antenna w/15'LMR 400311112-40015 Antenna Gains (dBi)2.47-0.65 Coax Loss (dB)0.91.3 Final Gain less Loss (dB)1.57-2.0 Output Power plus Final Gain (dBm EIRP)24.4323.2 19NMO Antenna w/15'LMR 400314203-40015 Antenna Gains (dBi)1.820.75 Coax Loss (dB)0.91.3 Final Gain less Loss (dB)0.9-0.6 Output Power plus Final Gain (dBm EIRP)23.824.6 Mobile Outside Antenna Kit Options FCC ID:PWO460006FCC ID:PWO460006 Final Output Power Limited to 30 dBm EIRP in all frequency bandsFinal Output Power Limited to 30 dBm EIRP in all frequency bands Uplink Frequency (MHz)824-8491850-1915Uplink Frequency (MHz)824-8491850-1915 Uplink Output Power (dBm)22.8625.15Uplink Output Power (dBm)22.8625.15 1Wide Band Directional Antenna With 75' LMR 400314411-400756Yagi Antenna 311124 With 100' LMR 400311124-400100 Antenna Gains (dBi)7.89.1Antenna Gains (dBi)9.64-11.97 Coax Loss (dB)3.65.4Coax Loss (dB)4.77.1 Final Gain less Loss (dB)4.23.7Final Gain less Loss (dB)4.9-19.07 Output Power plus Final Gain (dBm EIRP)27.0628.9Output Power plus Final Gain (dBm EIRP)27.86.1 2Wide Band Directional Antenna With 25' RG-58314411-58257Yagi Antenna 311124 With 40' RG-58311124-5840 Antenna Gains (dBi)7.89.1Antenna Gains (dBi)9.64-11.97 Coax Loss (dB)3.25.4Coax Loss (dB)5.28.6 Final Gain less Loss (dB)4.63.7Final…

Text truncated - open the document above for the full version.

November 21, 2013 Subject: RF MPE EXPOSURE Re: FCC ID: PWO460006 To Whom It May Concern: The MPE calculations for model 460006 signal booster were done for each frequency band: 800 MHz and 1900 MHz. The power density for multiple radiators was calculated as well as two calculations for each band; these included the different possibilities of antennas that may be connected to this signal booster: Mobile Outside and Fixed Outside Antennas. The Inside Antenna is integrated into the model 460006 Signal Booster and any other Inside Antenna is non- applicable to this device. The order of the attached calculations is as follows: 800 MHz band: 1. Mobile Outside Antenna: 311104 2. Fixed Outside Antenna: 311124-400100 1900 MHz band: 3. Outside Antenna: 311101 4. Fixed Outside Antenna: 314473-0640 Radiation Safety 5. Calculated Combined Power Density A booster’s uplink power must not exceed 1 watt equivalent isotropic radiated power (EIRP) for each band of operation. Composite downlink power must not exceed 0.05 watt EIRP for each band of operation ( 20.21(e)(8)(i)(D)). The following formula was used to calculate the equivalent isotropic radiated power: EIRP= Power Out (Watts)*Duty Cycle Percent*Antenna Gain (non-log)*Coax loss (non-log) The power density (mW/cm 2 ) is calculated using the following formula: Calculated Power Density=1000*EIRP (Watts)/(4*π*(Distance from Antenna (cm)^2)) Sincerely, Patrick L. Cook Senior Research and Development Engineer Minimum Safe Distance From Antennas Based upon FCC OET Bulletin 65 and other FCC Sources 11/27/2013, 8:42 AM460006 800 MHz Mobile Outside Antenna INPUT DATA Frequency MHz824 Pout Watts0.19320 Duty Cycle Percent100.0% Ant. Gain dBi2.48 Coax Loss dB0.00 Distance From Antenna In cm20.3 Ant. Gain less Coax Loss dBi2.48 Distance From Antenna In Inches8.00 EIRP (Watts)0.3420 FCC Power Density Limit (mw/cm 2 ) 0.55 Calculated Power Density (mw/cm 2 ) 0.0660 REFERENCE DATA Pout dBm22.86 Antenna Gain (non-log)1.77 Coax loss (non-log)1.00 General FCC Limit (mw/cm 2 ) f/1500 Antenna # 311104 RESULTS OF CALCULATIONS Minimum Safe Distance From Antennas Based upon FCC OET Bulletin 65 and other FCC Sources 11/27/2013, 8:42 AM460006 800 MHz Fixed Outside Antenna INPUT DATA Frequency MHz824 Pout Watts0.19320 Duty Cycle Percent100.0% Ant. Gain dBi9.60 Coax Loss dB4.70 Distance From Antenna In cm20.3 Ant. Gain less Coax Loss dBi4.90 Distance From Antenna In Inches8.00 EIRP (Watts)0.5970 FCC Power Density Limit (mw/cm 2 ) 0.55 Calculated Power Density (mw/cm 2 ) 0.1152 REFERENCE DATA Pout dBm22.86 Antenna Gain (non-log)9.12 Coax loss (non-log)0.34 General FCC Limit (mw/cm 2 ) f/1500 Antenna # 311124-400100 RESULTS OF CALCULATIONS Minimum Safe Distance From Antennas Based upon FCC OET Bulletin 65 and other FCC Sources 11/27/2013, 8:43 AM460006 1900 MHz Mobile Outside Antenna INPUT DATA Frequency MHz1850 Pout Watts0.32734 Duty Cycle Percent100.0% Ant. Gain dBi6.21 Coax Loss dB2.39 Distance From Antenna In cm20.3 Ant. Gain less Coax Loss dBi3.82 Distance From Antenna In Inches8.00 EIRP (Watts)0.7889 FCC Power Density Limit (mw/cm 2 ) 1.00 Calculated Power Density (mw/cm 2 ) 0.1522 REFERENCE DATA Pout dBm25.15 Antenna Gain (non-log)4.18 Coax loss (non-log)0.58 General FCC Limit (mw/cm 2 ) 1.00 Antenna # 311101 RESULTS OF CALCULATIONS Minimum Safe Distance From Antennas Based upon FCC OET Bulletin 65 and other FCC Sources 11/27/2013, 8:43 AM460006 1900 MHz Fixed Outside Antenna INPUT DATA Frequency MHz1850 Pout Watts0.32734 Duty Cycle Percent100.0% Ant. Gain dBi10.04 Coax Loss dB5.30 Distance From Antenna In cm20.3 Ant. Gain less Coax Loss dBi4.74 Distance From Antenna In Inches8.00 EIRP (Watts)0.9750 FCC Power Density Limit (mw/cm 2 ) 1.00 Calculated Power Density (mw/cm 2 ) 0.1881 REFERENCE DATA Pout dBm25.15 Antenna Gain (non-log)10.09 Coax loss (non-log)0.30 General FCC Limit (mw/cm 2 ) 1.00 Antenna # 314473-0640 RESULTS OF CALCULATIONS Radiation Safety - Combined Radiation From Amplifier and Cell Phone Calculated Power Density and Minimum Safe Distance For Cellular Phones (Uplink) INPUT DATA Frequency MHz (Uplink)8241850 Radiated Power (Watts)1.000001.00000 Duty Cycle Percent100.0%100.0% Distance From Antenna In cm20.320.3 RESULTS OF CALCULATIONS Distance From Antenna In Inches8.008.00 EIRP (Watts)1.00001.0000 FCC Power Density Limit (mw/cm 2 ) 0.551.00 Calculated Power Density (mw/cm 2 ) 0.19290.1929 Calculated Power Density and Minimum Safe Distance For Amplifier (Downlink) Frequency MHz8691930 Pout Watts1.57E-061.222E-06 Duty Cycle Percent100.0%100.0% Ant. Gain dBi0.702.60 Coax Loss dB0.000.00 Distance From Antenna In cm20.320.3 RESULTS OF CALCULATIONS Ant. Gain less Coax Loss dBi0.702.60 Distance From Antenna In Inches8.008.00 EIRP (Watts)0.000001850.00000222 FCC Power Density Limit (mw/cm 2 ) 0.581.00 Calculated Power Density (mw/cm 2 ) 0.00000040.0000004 Calculated Combined Power Density For Amplifier and Phone at 20.31 cm (8.0 in.) (Determined by most limiting factors) FCC Power Density Limit (mw/cm2)0.551.00 Combined Power Density for Phone and Amp (mw/cm 2 ) 0.1930.193 11/27/2013, 8:41 AMPower Density for Sleek DL with Phone UL

p1350026_FCC_Part 20_Rev 2.0 Page 1 of 69 Test Report Prepared for: Wilson Electronics, Inc. Model: 460006 Description: Dual Band Direct Contact Coupling Signal Booster FCC ID: PWO460006 To FCC Part 20 Date of Issue: October 14, 2013 On the behalf of the applicant: Wilson Electronics, Inc. 3301 E Deseret Drive St. George, UT 84790 To the attention of: Pat Cook, Sr. Electrical Engineer Ph: (435) 673-5021 Email: [email protected] Prepared By Compliance Testing, LLC 3356 N San Marcos Pl, Suite 107 Chandler, AZ 85225-7176 (866) 311-3268 phone / (480) 926-3598 fax www.compliancetesting.com Project No: p1350026 Mike Graffeo Project Test Engineer This report may not be reproduced, except in full, without written permission from Compliance Testing All results contained herein relate only to the sample tested p1350026_FCC_Part 20_Rev 2.0 Page 2 of 69 Test Report Revision History Revision Date Revised By Reason for Revision 1.0 October 14, 2013 Mike Graffeo Original Document 2…

Text truncated - open the document above for the full version.