Q3K-500TVWSSUTV White Space Subscriber Unit

INSTALLATION GUIDE RADWIN TV WHITE SPACE Release 1.0 FOR REGULATORY USES ONLY TV White Space Installation GuideRelease 1.01‐1 Table of Contents Chapter 1: Introduction 1.1 Scope of This Document...................................................................................................... 1‐1 1.2 RADWIN TV White Space Overview .................................................................................... 1‐1 1.2.1 Radio Units..................................................................................................................1-1 1.2.2 Method of Work..........................................................................................................1-3 1.2.3 Management Tools .....................................................................................................1-4 1.3 Key features of TV White Space .......................................................................................... 1‐4 1.4 What’s New in Release 1.0.................................................................................................. 1‐5 1.5 Notifications........................................................................................................................ 1‐5 Chapter 2: Installation Steps 2.1 Prepare Laptop.................................................................................................................... 2‐2 2.2 Connect Laptop to Radio Unit............................................................................................. 2‐2 2.2.1 TV White Space HBS Units...........................................................................................2-3 2.2.2 TV White Space SU Units.............................................................................................2-3 2.3 Update Connectivity Parameters of Radio Unit ................................................................. 2‐4 2.3.1 HBS Units.....................................................................................................................2-4 2.3.2 SU Units.......................................................................................................................2-5 2.4 Check items to be installed ................................................................................................. 2‐5 2.5 Prepare Tools ...................................................................................................................... 2‐6 2.6 Mount the HBS.................................................................................................................... 2‐6 2.6.1 Mounting the HBS with its antenn a ... .........................................................................2-6 2.6.2 Mounting the HBS adjacent to its antenna.................................................................2-7 2.7 Connect HBS antenna.......................................................................................................... 2‐7 2.8 Install SU Mounting Kit........................................................................................................ 2‐9 2.8.1 Standard Mounting Kit................................................................................................2-9 2.8.2 Vertical Pole ..............................................................................................................2-10 2.8.3 Horizontal Pole..........................................................................................................2-12 2.8.4 Wall...........................................................................................................................2-12 2.9 Mounting the SU ............................................................................................................... 2‐13 2.10 Ground Radio Unit........................................................................................................... 2‐13 2.10.1 HBS Units.................................................................................................................2-13 2.10.2 SU Units...................................................................................................................2-14 2.11 Mounting the Lightning P rotection Units........................................................................ 2‐14 2.12 Waterproofing................................................................................................................. 2‐17 2.13 Connect Radio (External Connections)............................................................................ 2‐18 2.13.1 HBS Units.................................................................................................................2-18 2.13.2 SU Units...................................................................................................................2-19 2.14 Check Connectivity to Radio............................................................................................ 2‐19 2.15 Request (and receive) permitted frequencies................................................................. 2‐20 2.16 Activate HBS.................................................................................................................... 2‐20 2.17 Align SU Unit ................................................................................................................... 2‐21 Chapter 3: Safety Practices and Provisions 3.1 Scope of this Chapter .......................................................................................................... 3‐1 3.1.1 Preventing Overexposure to RF Energy.......................................................................3-1 3.1.2 Grounding ...................................................................................................................3-1 3.1.3 Protection against Lightning.......................................................................................3-1 3.1.4 General.............................................................................................…

Text truncated - open the document above for the full version.

Nemko Canada Inc. 303 River Road Ottawa, Ontario, Canada K1V 1H2 FCC ID: Q3K-500TVWSSU Model: TVWS SU INT Request for Permanent Confidentiality Pursuant to Sections 0.457(d) and 0.459 of the Commission’s rules, we hereby request that the following documents be held confidential:  Schematics  Block diagram  Bill of Materials  Operational description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated: 1/9/2020 Signed: Printed name: Shlomo Weiss Title: Standardization Officer On behalf of: Radwin, Ltd.

Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent FCC On our behalf, I appoint Tom Tidwell of Nemko USA, Inc. at 2648 FM 407, Suite 200, Bartonville, TX 76226 to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in FCC regulations will have affixed to it a label identical to that submitted for approval with this application. In signing this letter, Applicant certifies that neither the applicant nor any party to the application is not subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. § 862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a "party" for these purposes. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with Radwin, Ltd.. Dated: 1/9/2020 Agency agreement expiration date: 1/8/2021 Sincerely, Shlomo Weiss Standardization Officer

LABEL AND LABEL LOCATION Label Artwork Label Location

TVWS SU INT INTERNL PHOTOS Photo 1: Internal Assembly View Photo 2: PCB C.S. view Photo 3: PCB C.S. view with shields off Photo 4: PCB P.S. view Photo 5: Antenna assembly top view Photo 6: Antenna assembly bottom view Photo 7: GPS module assembled on antenna

Prediction of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 where:S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna Maximum peak output power at device output terminal:26.70dBm Cable and Jumper loss:0.0dB Maximum peak output power at antenna input terminal:26.70dBm 467.7351413mW Single Antenna gain (typical):3dBi Number of Antennae:1 Total Antenna gain (typical):3dBi 1.995262315(numeric) Prediction distance:20cm Prediction frequency:2422MHz MPE limit for uncontrolled exposure at prediction frequency:1mW/cm 2 Power density at prediction frequency:0.185665 mW/cm 2 1.856650W/m 2 Tx On time:1.000000ms Tx period time:1.000000ms Average Factor:100.000000% Average Power density at prediction frequency:1.856650W/m 2 Maximum allowable antenna gain:10.31269855dBi Margin of Compliance:7.312698554dB 2 4R PG S   Choose Scandinavian trust

www.nemko.com Nemko Canada Inc., a testing laboratory, is accredited by the Standards Council of Canada. The tests included in this report are within the scope of this accreditation FCC 15.247 and RSS-247.docx; Date: Apr 2019 MRA il ac SCC Accredited LAB LAB Accrédité CCN TM Choose Scandinavian trust Wireless test report – 378820-3TRFWL Type of assessment: Original Certification Applicant: RADWIN Ltd. Product type: 2.4 GHz Wi-Fi Module Incorporated in Television Band Device (TVBD) Model (of TVBD): Model variant (of TVBD): TVWS SU INT RW-5HA0-0PWS FCC ID (of TVBD): Q3K-500TVWSSU Test standard specification: FCC 47 CFR Part 15 Subpart C, §15.247 Operation in the 902–928 MHz, 2400–2483.5 MHz, and 5725–5850 MHz Date of issue: December 10, 2019 Andrey Adelberg, Senior EMC/Wireless Specialist Tested by Signature Kevin Rose, Wireless/EMC Specialist Reviewed by Signature Report reference ID: 378820-3TRFWL Applicant: RADWIN Ltd. Model: TVWS SU INT Page 2 of 41 Test location(s) Company name Nemko Canada Inc. Site name Ottawa Address 303 River Road City Ottawa Province Ontario Postal code K1V 1H2 Country Canada Telephone +1 613 737 9680 Facsimile +1 613 737 9691 Toll free +1 800 563 6336 Website www.nemko.com Site number (3 m SAC) FCC: CA2040; IC: 2040A-4 Limits of responsibility Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. All results contain in this report are within Nemko Canada’s ISO/IEC 17025 accreditation. Copyright notification Nemko Canada Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko Canada Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. © Nemko Canada Inc. Report reference ID: 378820-3TRFWL Applicant: RADWIN Ltd. Model: TVWS SU INT Page 3 of 41 Table of contents Table of contents .......................................................................................................................................................................................................... 3 Section 1. Report summary ................................................................................................................................................................................. 4 1.1 Applicant and manufacturer .................................................................................................................................................................................... 4 1.2 Test specification ...................................................................................................................................................................................................... 4 1.3 Test methods ............................................................................................................................................................................................................ 4 1.4 Statement of compliance ......................................................................................................................................................................................... 4 1.5 Exclusions ................................................................................................................................................................................................................. 4 1.6 Test report revision history ...................................................................................................................................................................................... 4 Section 2. Summary of test results ....................................................................................................................................................................... 5 2.1 FCC Part 15 Subpart C, general requirements test results ........................................................................................................................................ 5 2.2 FCC Part 15 Subpart C, intentional radiators test results for digital transmission systems (DTS) ............................................................................. 5 Section 3. Equipment under test (EUT) details ..................................................................................................................................................... 6 3.1 Sample information .................................................................................................................................................................................................. 6 3.2 EUT information ....................................................................................................................................................................................................... 6 3.3 Technical information .............................................................................................................................................................................................. 6 3.4 Product description and theory of operation ........................................................................................................................................................... 6 3.5 EUT exercise details .................................................................................................................................................................................................. 6 3.6 EUT setup diagram ..........................................................................…

Text truncated - open the document above for the full version.