Q3K-NEO5XSingle Carrier 5.x GHz Base Station with Beamforming Antenna, Dual Carrier 5.x GHz Base Station with Beamforming Antenna

NEO, NEO DUO Single, Dual Carrier 5 GHz Base Station with Beamforming Antenna REFERENCE GUIDE Regulatory Compliance FCC/ISED - Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and ISED RSS standards. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Outdoor units and antennas should be installed ONLY by experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities. Failure to do so may void the product warranty and may expose the end user or the service provider to legal and financial Caution liabilities. Resellers or distributors of this equipment are not liable for injury, damage or violation of regulations associated with the installation of outdoor units or antennas. The installer should configure the output power level of antennas according to country regulations and antenna type. Les unités extérieures et les antennes doivent être installés que par des professionnels expérimentés d'installation qui sont familiers avec les normes locales et les codes de sécurité et, si applicable, sont agréées par les autorités gouvernementales de réglementation compétents. Ne pas le faire peut annuler la garantie du produit et peuvent exposer l'utilisateur final ou le fournisseur de services d'obligations juridiques et financiers. Revendeurs ou distributeurs de ces équipements ne sont pas responsables des blessures, des dommages ou violation des règlements liés à l'installation des unités extérieures ou des antennes. L'installateur doit configurer le niveau de puissance de sortie des antennes conformément aux réglementations nationales et le type d'antenne. NEO, NEO DUO Reference Guide i Prudence This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. Warning Les antennes utilisées pour cet émetteur doivent être installées de manière à fournir une distance de séparation d'au moins 20 cm par rapport à toutes les personnes The device is granted to operate under FCC Rules in the 5.2 / 5.3 / 5.4 / 5.8 GHz bands. Warning Le module est autorisé à fonctionner sous certification ISDE dans les bandes 5,3 / 5,4 / 5,8 GHz. This device complies with Part 15 of the FCC rules and with ISED license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES-003. NEO, NEO DUO Reference Guide ii Avertissement Overview The NEO, NEO DUO is a single or dual carrier base station radio device. It encapsulates two 5.x GHz radio modules as well as independent beamforming antenna for each individual radio. The unit is designed to deliver up to 2 x 1500Mbps. It supports 10, 20, 40 80 MHz channel bandwidths in the frequency range 5150 – 5250 MHz*, 5725 - 5850 MHz. It is using OFDM transmission technique in TDD Duplexing method. The modulation supported is BPSK, QPSK, 16QAM, 64QAM, 256QAM OFDM The NEO incorporates a beamforming antenna coupled with a radio with software capability to toggle between wide and narrow operating modes. The NEO DUO incorporates an independent beamforming antenna for each radio with software capability to toggle between wide and narrow beamwidths operating modes. The NEO, NEO DUO is powered by a PoE device and has a LAN port option. The NEO, NEO is certified under the identification numbers FCC ID: Q3K-NEO5X and IC: 5100A-NEO5X. * Only supported under FCC Rules Condition of Use The NEO, NEO DUO is a proprietary radio device and can only be deployed and maintained by RADWIN professional installers or its authorized subcontractors FCC Rules and ISED Regulation Restrictions The ODU firmware is factory programmed to operate under the FCC rules and ISED regulation restrictions. The firmware is locked and inaccessible by any third party. As a result o…

Text truncated - open the document above for the full version.

RDWN73 FCC Restriction Config Control Attestation Rev1.1.docx Date: April 4, 2021 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: FCC Restriction Configuration Control Attestation for FCC ID: Q3K-NEO5X To Whom It May Concern: RADWIN Ltd. attests that the software of the model: NEO, NEO DUO conforms to the requirements of the FCC’s “SOFTWARE SECURITY REQUIREMENTS FOR U-NII DEVICES” specified in 594280 D02 U-NII Device Security v01r03 and KDB 442812 D01 SDR Apps Guide v02r03 under the SDR rules. We have submitted separate documentation to the FCC outlining the software security features. Furthermore that the software of the NEO, NEO DUO cannot be modified by any third party in any way that causes the NEO, NEO DUO to operate in violation of the limits of the FCC GRANT OF EQUIPMENT AUTHORIZATION for FCC ID: Q3K-NEO5X. Sincerely Yours, Name: Shlomo Weiss Date: April 4, 2021 Title: Standardization Officer RADWIN Ltd. Phone: +972-3-7662988 Fax: +972-3-7662902 Email: [email protected]

Model Difference Declaration Letter There are 2 models requested for approval under FCC ID: Q3K-NEO5X 1. NEO 2. NEO DUO The radio module, the digital board and the beamforming antenna is identical in both models. The models indicate single or dual assembly options as shown below – 1. NEO – assembly incorporating a single digital board, a single radio module, and a single beamforming antenna 2. NEO DUO – assembly incorporating a single digital board, two radio modules, and a two beamforming antennas. Name: Shlomo Weiss Title: Standardization Officer Signature of applicant

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: April 4, 2021 Subject; Request for Confidentiality FCC ID: Q3K-NEO5X To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Additionally the device is not accessible to users being installed in hosts manufactured only by RADWIN and hosts being mounted on antenna towers. Schematic Diagram Block Diagram Parts List Operational Description Security Descriptions In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); Internal Photos External Photos Test Setup Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Shlomo Weiss Title: Standardization Officer

Agent Authorization Company: RADWIN Ltd. Address: 27 Habarzel Street Tel Aviv, 6971039 Israel Product Name: Single Carrier 5.x GHz Base Station with Beamforming Antenna, Dual Carrier 5.x GHz Base Station with Beamforming Antenna Model Number(s): NEO, NEO DUO Product Description: Single Carrier 5.x GHz Base Station with Beamforming Antenna, Dual Carrier 5.x GHz Base Station with Beamforming Antenna We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: April 1, 2021 Name: Shlomo Weiss Title: Standardization Officer Company: RADWIN Ltd.

RDWN73 Software Config Control Declaration Rev1.1.docx FCC Software Configuration Control Declaration Date: April 4, 2021 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Attn: OET Dept. Product/ Model Number: NEO, NEO DUO Regarding FCC Country Code Selection guidelines identified in KDB 594280. “All applications for equipment authorization for transmitters that can have radio parameters, or other technical parameters, reported to the Commission set by software must have an attestation indicating that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified.” We declare that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. Name: Shlomo Weiss Date: April 4, 2021 Title: Standardization Officer Signature of applicant

PHOTOS - EXTERNAL Company: Radwin Product Name: NEO Report No.: RDWN73 – External Photos Title: RDWN73 External Photos To: Serial #: Issue Date: 20 April 2021 Page: 2 of 6 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com 1. External Photographs 1.1.1. Product - External Front View Title: RDWN73 External Photos To: Serial #: Issue Date: 20 April 2021 Page: 3 of 6 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com Back View Bottom View Title: RDWN73 External Photos To: Serial #: Issue Date: 20 April 2021 Page: 4 of 6 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com Left View Right View Title: RDWN73 External Photos To: Serial #: Issue Date: 20 April 2021 Page: 5 of 6 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com Top View 575 Boulder Court Pleasanton, California 94566, USA Tel: +1 (925) 462 0304 Fax: +1 (925) 462 0306 www.micomlabs.com

LABEL AND LABEL LOCATION NEO label Artwork NEO DUO Label Artwork Label Location

PHOTOS - INTERNAL Company: Radwin Product Name: NEO Report No.: RDWN73 – Internal Photos Title: RDWN73 Internal Photos To: Serial #: Issue Date: 20 April 2021 Page: 2 of 11 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com 1. Internal Photographs 1.1.1. Product - Internal Antenna Assembly Front Title: RDWN73 Internal Photos To: Serial #: Issue Date: 20 April 2021 Page: 3 of 11 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com Left Antenna Assembly Back Left Antenna Assembly Front Title: RDWN73 Internal Photos To: Serial #: Issue Date: 20 April 2021 Page: 4 of 11 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com Left Antenna Assembly Front panel removed Left Radio Module Back Title: RDWN73 Internal Photos To: Serial #: Issue Date: 20 April 2021 Page: 5 of 11 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com Left Radio Module Front Left Radio Module Front Shield Removed Title: RDWN73 Internal Photos To: Serial #: Issue Date: 20 April 2021 Page: 6 of 11 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com Main Board Back Main Board Front Title: RDWN73 Internal Photos To: Serial #: Issue Date: 20 April 2021 Page: 7 of 11 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com Main Board in unit Right Antenna Assembly Back Title: RDWN73 Internal Photos To: Serial #: Issue Date: 20 April 2021 Page: 8 of 11 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com Right Antenna Assembly Front Right Antenna Assembly Front panel removed Title: RDWN73 Internal Photos To: Serial #: Issue Date: 20 April 2021 Page: 9 of 11 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com Right Radio Module Back Right Radio Module Front Title: RDWN73 Internal Photos To: Serial #: Issue Date: 20 April 2021 Page: 10 of 11 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com Right Radio Module Front Shield Removed 575 Boulder Court Pleasanton, California 94566, USA Tel: +1 (925) 462 0304 Fax: +1 (925) 462 0306 www.micomlabs.com

MPE/RF EXPOSURE REPORT FCC CFR 47 Part 1.1310 Report No.: RDWN73-U2_FCC_MPE Rev A Company: Radwin Model Name: NEO, NEO DUO MPE/RF EXPOSURE REPORT Company Name: Radwin Model Name: NEO, NEO DUO To: FCC CFR 47 Part 1.1310 Report Serial No.: RDWN73-U2_FCC_MPE Rev A This report supersedes: NONE Applicant: Radwin 27 Habarzel Street Tel Aviv, 6971039 Israel Issue Date: 19 th April 2021 This Test Report is Issued Under the Authority of: MiCOM Labs, Inc. 575 Boulder Court Pleasanton California 94566 USA Phone: +1 (925) 462-0304 Fax: +1 (925) 462-0306 www.micomlabs.com MiCOM Labs is an ISO 17025 Accredited Testing Laboratory Title: Radwin NEO, NEO DUO To: FCC CFR 47 Part 1.1310 Serial #: RDWN73-U2 FCC MPE Draft Issue Date: 19 th April 2021 Page: 3 of 5 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com 1. MAXIMUM PERMISSABLE EXPOSURE Calculations for Maximum Permissible Exposure Levels Power Density = Pd (mW/cm 2 ) = EIRP/(4*π*d 2 ) EIRP = P * G P = Peak output power (mW) G = Antenna numeric gain (numeric) d = Separation distance (cm) Numeric Gain = 10 ^ (G (dBi)/10) These calculations represent worst case in terms of the exposure levels. Limits for Occupational/Controlled Exposure for professional installation: 5 mW/cm 2 Non-Beamforming Freq. Band (MHz) Ant Gain (dBi) Numeric Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Calculated Power Density (mW/cm 2 ) @ 20cm Power Density Limit (mW/cm 2 ) Min Calculated safe distance for Limit (cm) Calculated Power Density (mW/cm 2 ) @ Safe Distance 5150.0 - 5250.0 10.00 10.00 25.75 375.84 0.748 5.00 7.734 5.00 5250.0-5350.0 10.00 10.00 19.91 97.95 0.195 5.00 3.948 5.00 5470.0-5725.0 10.00 10.00 19.87 97.05 0.193 5.00 3.930 5.00 5725.0 - 5850.0 11.00 12.59 24.98 314.77 0.788 5.00 7.942 5.00 Beamforming Freq. Band (MHz) Ant Gain (dBi) Numeric Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Calculated Power Density (mW/cm 2 ) @ 20cm Power Density Limit (mW/cm 2 ) Min Calculated safe distance for Limit (cm) Calculated Power Density (mW/cm 2 ) @ Safe Distance 5150.0 - 5250.0 16.00 39.81 19.95 98.86 0.783 5.00 7.91 5.00 5250.0-5350.0 16.00 39.81 13.88 24.43 0.194 5.00 3.93 5.00 5470.0-5725.0 16.00 39.81 13.93 24.72 0.196 5.00 3.96 5.00 5725.0 - 5850.0 17.00 50.12 18.93 78.16 0.779 5.00 7.90 5.00 Note: for mobile or fixed location transmitters the minimum separation distance is 20cm, even if calculations indicate the MPE distance to be less. Title: Radwin NEO, NEO DUO To: FCC CFR 47 Part 1.1310 Serial #: RDWN73-U2 FCC MPE Draft Issue Date: 19 th April 2021 Page: 4 of 5 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com The following assessments are worst case exposure conditions where the RADWIN NEO DUO contains 2 radio modules:- 2 x 5GHz 802.11 with both radios transmitting simultaneously;- Non-BeamForming Freq. Band (MHz) Ant Gain (dBi) Numeric Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Calculated Power Density (mW/cm 2 ) @ 20cm Power Density Limit (mW/cm 2 ) E ref Min Calculated safe distance for Limit (cm) Summation E i /E ref @ 20 cm 5150.0 - 5250.0 16.00 39.81 19.95 98.86 0.748 5.00 7.734 0.748 5725.0 - 5850.0 17.00 50.12 18.93 78.16 0.788 5.00 7.942 0.788 EIRP TOTAL (mW/EIRP) : 7721.15 20 cm distance Total Evaluation: 1.54 mW/cm 2 BeamForming Freq. Band (MHz) Ant Gain (dBi) Numeric Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Calculated Power Density (mW/cm 2 ) @ 20cm Power Density Limit (mW/cm 2 ) Min Calculated safe distance for Limit (cm) Summation E i /E ref @ 20 cm 5150.0 - 5250.0 16.00 39.81 19.95 98.86 0.783 5.00 7.91 0.783 5725.0 - 5850.0 17.00 50.12 18.93 78.16 0.779 5.00 7.90 0.779 EIRP TOTAL (mW/EIRP) : 7852.9195 20 cm distance Total Evaluation: 1.56 mW/cm 2 Note: for mobile or fixed location transmitters the minimum separation distance is 20cm, even if calculations indicate the MPE distance to be less. Specification Maximum Permissible Exposure Limits FCC §1.1310 Limit = 5mW / cm 2 from 1.310 Table 1 575 Boulder Court Pleasanton, California 94566, USA Tel: +1 (925) 462 0304 Fax: +1 (925) 462 0306 www.micomlabs.com

REGULATORY COMPLIANCE TEST REPORT FCC CFR 47 15.407, RSS-247 Issue 2 Report No.: RDWN73-U3 Rev A Company: Radwin Model Name: NEO, NEO DUO REGULATORY COMPLIANCE TEST REPORT Company Name: Radwin Model Name: NEO, NEO DUO To: FCC CFR 47 Part 15 Subpart E 15.407, RSS-247 Test Report Serial No.: RDWN73-U3 Rev A This report supersedes: NONE Applicant: Radwin 27 Habarzel Street Tel Aviv, 6971039 Israel Issue Date: 12 th April 2021 This Test Report is Issued Under the Authority of: MiCOM Labs, Inc. 575 Boulder Court Pleasanton California 94566 USA Phone: +1 (925) 462-0304 Fax: +1 (925) 462-0306 www.micomlabs.com MiCOM Labs is an ISO 17025 Accredited Testing Laboratory Title: Radwin NEO, NEO DUO To: FCC CFR 47 Subpart E 15.407, ISED RSS 247 Serial #: RDWN73-U3 Rev A Issue Date: 12 th April 2021 Page: 3 of 167 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com Table of Contents 1. ACCREDITATION, LISTINGS & RECOGNITION ................................................................................ 4 1.1. TESTING ACCREDITATION ........................................................................................................ 4 1.2. RECOGNITION ............................................................................................................................. 5 1.3. PRODUCT CERTIFICATION ........................................................................................................ 6 2. DOCUMENT HISTORY ......................................................................................................................... 7 3. TEST RESULT CERTIFICATE ............................................................................................................. 8 4. REFERENCES AND MEASUREMENT UNCERTAINTY ..................................................................... 9 4.1. Normative References .................................................................................................................. 9 4.2. Test and Uncertainty Procedure ................................................................................................. 10 5. EMC TEST SUMMARY ....................................................................................................................... 11 5.1. Technical Details ......................................................................................................................... 11 5.2. Scope Of Test Program .............................................................................................................. 12 5.3. Equipment Model(s) and Serial Number(s) ................................................................................. 13 5.4. Antenna Details ........................................................................................................................... 13 5.5. Cabling and I/O Ports .................................................................................................................. 13 5.6. Test Configurations ..................................................................................................................... 13 5.7. Equipment Modifications ............................................................................................................. 14 5.8. Deviations from the Test Standard ............................................................................................. 14 6. TEST SUMMARY ................................................................................................................................ 15 7. TEST EQUIPMENT CONFIGURATION(S) ......................................................................................... 16 7.1. Radiated Emissions - 3m Chamber ............................................................................................ 16 8. MEASUREMENT AND PRESENTATION OF TEST DATA ............................................................... 18 9. TEST RESULTS .................................................................................................................................. 19 9.1. Peak Transmit Power .................................................................................................................. 19 9.1.1. Non-Beamforming ................................................................................................................ 22 9.1.2 Beamforming ...................................................................................................................... 26 9.2. 6 dB & 99% Bandwidth ............................................................................................................... 30 9.3. Power Spectral Density ............................................................................................................... 35 9.3.1. Non-Beamforming ................................................................................................................ 37 9.3.2. Beamforming ........................................................................................................................ 41 9.4. Radiated ...................................................................................................................................... 45 9.4.1. TX Spurious & Restricted Band Emissions .......................................................................... 48 9.4.1.1. RADWIN MR0269440 .................................................................................................... 48 9.4.1.2. RADWIN MR0269440BF ............................................................................................... 51 9.4.2. Restricted Edge & Band-Edge Emissions ............................................................................ 54 9.4.2.3. RADWIN MR0269440 .....................…

Text truncated - open the document above for the full version.

REGULATORY COMPLIANCE TEST REPORT FCC CFR 47 Part 15 Subpart E 15.407 Report No.: RDWN73-U4 Rev A Company: Radwin Model Name: NEO, NEO DUO REGULATORY COMPLIANCE TEST REPORT Company Name: Radwin Model Name: NEO, NEO DUO To: FCC CFR 47 Part 15 Subpart E 15.407 Test Report Serial No.: RDWN73-U4 Rev A This report supersedes: NONE Applicant: Radwin 27 Habarzel Street Tel Aviv 6971039 Israel Issue Date: 12 th April 2021 This Test Report is Issued Under the Authority of: MiCOM Labs, Inc. 575 Boulder Court Pleasanton California 94566 USA Phone: +1 (925) 462-0304 Fax: +1 (925) 462-0306 www.micomlabs.com MiCOM Labs is an ISO 17025 Accredited Testing Laboratory Title: Radwin NEO, NEO DUO To: FCC CFR 47 Part 15 Subpart E 15.407 Serial #: RDWN73-U4 Rev A Issue Date: 12 th April 2021 Page: 3 of 149 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com Table of Contents 1. ACCREDITATION, LISTINGS & RECOGNITION ................................................................................ 5 1.1. TESTING ACCREDITATION ........................................................................................................ 5 1.2. RECOGNITION ............................................................................................................................. 6 1.3. PRODUCT CERTIFICATION ........................................................................................................ 7 2. …

Text truncated - open the document above for the full version.