Q3KRW5XMODRF module operating in the 4.9-5.8 GHz band

AP0127730, AP0134760 RF Module Operating in the 4.9-5.8 GHz bands REFERENCE GUIDE Regulatory Compliance FCC/IC - Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and IC RSS standards. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. It is the responsibility of the installer to ensure that when using the outdoor antenna kits, only those antennas certified with the product are used. The use of any antenna other than those certified with the product is expressly forbidden by FCC rules 47 CFR part 15.204 and IC RSS standards. Warning Outdoor units and antennas should be installed ONLY by experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities. Failure to do so may void the product warranty and may expose the end user or the service provider to legal and financial Caution liabilities. Resellers or distributors of this equipment are not liable for injury, damage or violation of regulations associated with the installation of outdoor units or antennas. The installer should configure the output power level of antennas according to country regulations and antenna type. This equipment should be installed and operated with a minimum distance of 354cm between the radiator and your body. Warning The module is granted to operate under FCC certification in the 4.9 GHz and 5.8 GHz bands only. Warning AP0127730, AP0134760 Reference Guide i This device complies with Part 15 of the FCC rules and with Industry Canada license- exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la norme d'Industrie Canada exempts de licence RSS (s). Son fonctionnement est soumis aux deux conditions suivantes: 1. Cet appareil ne peut pas causer d'interférences, et 2. Cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada AP0127730, AP0134760 Reference Guide ii Warning Devices subject to RSS-210 Annex 9 shall not be capable of transmitting in the band 5600-5650 MHz. Overview The AP0127730, AP0134760 is an RF module operating in the 4.9 – 5.8 GHz frequency bands. It is a TDD OFDM radio supporting 5 MHz, 10 MHz, 20 MHz and 40 MHz channel bandwidths. The RF module cannot work as a stand-alone device. It can operate and be controlled only when attached to a digital main board and altogether assembled in an enclosure suitable for outdoor use. The assembly of the RF module attached to the digital main board is hereafter referred to as ‘ODU’. The ODU in its various outdoor enclosures is manufactured by RADWIN. The RF module is certified as a limited modular approval type with the FCC ID: Q3KRW5XMOD and IC: 5100A-RW5XMOD. Condition of Use The AP0127730, AP0134760 RF module is a proprietary radio interface and can only be connected to digital boards manufactured by RADWIN. The ODU resides in an outdoor enclosure also manufactured and assembled by RADWIN or its subcontractors. The RF module is not for sale to the general public. Antennas The AP0127730, AP0134760 RF module is certified with various antenna types covering both Point-to-Point and Point-to-Multipoint systems. They are all dual pole cross polarized antennas and they are the only ones to be used with the RF module. AP0127730, AP0134760 Reference Guide 1 Certified Antennas Following is the list of antennas certified for use with the AP0127730, AP0134760 RF module: Antenna Type Manufacturer Model Number Antenna Max Gain (dBi) Sector Dual Pole Integrated 120 Deg RADWIN Ltd. MT0128930 11 Sector Dual Pole 120 Deg RADWIN Ltd. RW-9061-5004 11 Sector Dual Pole Integrated 95 Deg RADWIN Ltd. AM0135060 12 Sector Dual Pole 90 Deg RADWIN Ltd. RW-9061-5001 14 Sector Dual Pole 60 Deg RADWIN Ltd. RW-9061-5002 16.5 Sector Dual Pole Integrated 90 Deg RADWIN Ltd. MT0125250 13 Flat Panel Dual Pole Integrated RADWIN Ltd. AM0119960 16 Flat Panel Dual Pole Integrated RADWIN Ltd. AM0111760 16.5 Flat Panel Dual Pole Integrated RADWIN Ltd. MT0070760 24 Flat Panel Dual Pole External RADWIN Ltd. RW-9612-5001 23 Flat Panel Dual Pole External RADWIN Ltd. RW-9622-5001 29 Dual Pole Dish RADWIN Ltd. RW-9721-5158 29 Dual Pole Dish RADWIN Ltd. RW-9732-4958* 32 * Only for the 5.8 GHz band Maximum Output Power 5725 – 5850 MHz band - FCC/IC The maximum output power can be set as follows, when operating in the 5.8 GHz band, under FCC and IC regulations. The power values are for PtP systems and PtMP systems with 0 to 6 dBi total antenn…

Text truncated - open the document above for the full version.

Letter of Authorization Company: RADWIN Ltd. Address: 27 Habarzel Street, Tel Aviv, Israel, 69710 Product Name: RF module operating in the 4.9-5.8 GHz bands Model Number: AP0127730, AP0134760 We authorize MiCOM Labs, 440 Boulder Court, Suite 200, Pleasanton, CA 94566, USA, to act on our behalf on all matters concerning the above named equipment. This shall include the following: - Testing - Approval applications and procedures - Payment of approval fees We declare that MiCOM Labs, 440 Boulder Court, Suite 200, Pleasanton, CA 94566, USA, is allowed to forward all information related to the approval project to the applied notified body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Name: Itai Rubinstein Date: November 25, 2012 Title: Engineering Department Manager Signature of applicant

www.radwin.com Address goes here Address goes here Address goes here Beamforming Statement To whom it may concern, RADWIN Ltd. herby states that the models AP0127730, AP0134760 under FCC ID: Q3KRW5XMOD and IC: 5100A-RW5XMOD have no beamforming capabilities. Itai Rubinstein December 10, 2012 Engineering Department Manager RADWIN Ltd.

www.radwin.com Address goes here Address goes here Address goes here DC Voltage/Current Info for Module AP0127730, AP0134760 DC Voltage/Current info as required by FCC rule 2.1033(c)(8) The diagram details the Voltage/Current consumption values of the AP0127730, AP0134760 module when operating at the highest load.

www.radwin.com Address goes here Address goes here Address goes here Justification for Using Emission Designator ‘W7W’ RADWIN has chosen the Emission Designator ‘W7W’ for the following reasons: 1. The transmitted signal is based on 802.11n OFDM encoding in modulation formats BPSK, QPSK, 16QAM, 64QM operating in more than two channels and in four channel bandwidths. 2. The transmission can deliver data, voice and video information. 3. The first ‘W’ character defines the definition an emission consists of the main carrier modulated in a combination of amplitude and angle. 4. The character ‘7’ defines that there are more than two channels containing digital information. 5. The second ‘W’ character defines that there is a combination of data, voice and video that can be transmitted. Itai Rubinstein December 10, 2012 Engineering Department Manager RADWIN Ltd.

www.radwin.com Address goes here Address goes here Address goes here Modular Approval Request Letter To: Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 To: Industry Canada Certification and Engineering Bureau 3701 Carling Avenue Bldg. 94 P.O. Box 11490, Station “H” Ottawa, Ontario K2H 8S2 CANADA RE: Limited Modular Approval Request Dear certification officers, Pursuant to the FCC Rule 15.212 Modular transmitters and KDB 966369 D01 Module Certification Guide v01r03, RADWIN Ltd. herby applies for Limited Modular Approval for the Models AP0127730, AP0134760 under FCC ID: Q3KRW5XMOD and IC: 5100A-RW5XMOD. The justification for the application is based on the attestation that RADWIN Ltd., being the sole manufacturer and the assembling factory of both the module and the final product, has full control over the production line and the final product. The module is assembled in enclosures manufactured and tested by RADWIN or its approved subcontractors. The module will not be marketed, distributed or sold to the general public as it is incapable of operating as a standalone product. It is installed only in devices manufactured by RADWIN Ltd. or its approved subcontractors. According to the requirements in section 15.212 of FCC rules - 1. The module has its own RF shielding as shown in the presented in the photo at the end of this document. 2. The module has buffered data/modulation inputs provided by the Atheros. 3. The module has on board the power supply regulation. 4. The module is supplied with unique antenna connector. The module is installed into the device at RADWIN’s production line with the unique antenna cabling and connectors, as tested. Only the RADWIN antennas detailed in the manual are marketed with the module. The final installation of the unit is done only by professional installers trained by RADWIN representatives. www.radwin.com Address goes here Address goes here Address goes here 5. The unit was tested in a stand-alone configuration. The test was performed with an open configuration enclosure with the module exposed and attached to a digital board representing typical RADWIN host configuration. 6. The module will be labeled with the FCC ID: Q3KRW5XMOD and IC: 5100A-RW5XMOD as shown in the photo at the end of this document. The device into which the module is installed will also display a label referring to the enclosed module as shown at the end of this document: “Contains FCC ID: Q3KRW5XMOD, Contains IC: 5100A-RW5XMOD”. 7. The module was tested for compliance with FCC rule Part 15 subparts C and E and Part 90 subpart Y. The integration of the module is done by RADWIN and there is no access to RADWIN manufactured device by third party. 8. The module complies with RF exposure requirements as shown in the MPE documents. Photographs Module with the RF shielding and Label External Label sample attached to host enclosure Itai Rubinstein December 10, 2012 Engineering Department Manager RADWIN Ltd.

1.1.1. Maximum Permissible Exposure FCC, Part 90 Subpart C §90.1217 Industry Canada RSS-Gen §5.6 Calculations for Maximum Permissible Exposure Levels Power Density = Pd (mW/cm 2 ) = EIRP/(4πd 2 ) EIRP = P * G P = Peak output power (mW) G = Antenna numeric gain (numeric) d = Separation distance (cm) Numeric Gain = 10 ^ (G (dBi)/10) Because the EUT belongs to the General Population/Uncontrolled Exposure the limit of power 2 density is 1.0 mW/cm Note: for mobile or fixed location transmitters the minimum separation distance is 20cm, even if calculations indicate the MPE distance to be less. Specification Maximum Permissible Exposure Limits §90.1217 Licensees and manufacturers are subject to the radiofrequency radiation exposure requirements specified in §§ 1.1307(b), 2.1091 and 2.1093 of this chapter, as appropriate. Applications for equipment authorization of mobile or portable devices operating under this section must contain a statement confirming compliance with these requirements for both fundamental emissions and unwanted emissions. Technical information showing the basis for this statement must be submitted to the Commission upon request. FCC §1.1310 Limit = 1mW / cm 2 from 1.310 Table 1 RSS-Gen §5.6 Category I and Category II equipment shall comply with the applicable requirements of RSS-102. Laboratory Measurement Uncertainty for Power Measurements Measurement uncertainty ±1.33dB 4940 – 4990 MHz Antenna Model Type Ant Gain (dBi) Numeric Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Calculated Safe Distance @ 1mW/cm 2 Limit(cm) Power Density @ 20cm (mW/cm 2 ) MT0128930 Sector Dual Pole Integrated 120 Deg 1113 24.6 288.40 17.00 0.72 RW-9061-5004 Sector Dual Pole 120 Deg 1113 24.6 288.40 17.00 0.72 AM0135060 Sector Dual Pole Integrated 95 Deg 1216 24.6 288.40 19.07 0.91 RW-9061-5001 Sector Dual Pole 90 Deg 1425 24.6 288.40 24.01 1.44 RW-9061-5002 Sector Dual Pole 60 Deg 15.535 24.6 288.40 28.54 2.04 MT0125250 Sector Dual Pole Integrated 90 Deg 1320 24.6 288.40 21.40 1.14 AM0119960 Flat Panel Dual Pole Integrated 1640 24.6 288.40 30.23 2.28 AM0111760 Flat Panel Dual Pole Integrated 1640 24.6 288.40 30.23 2.28 RW-9612-5001 Flat Panel Dual Pole External 23200 24.6 288.40 67.67 11.45 MT0070760 Flat Panel Dual Pole Integrated 23.5224 24.6 288.40 71.68 12.84 RW-9622-5001 Flat Panel Dual Pole External 29794 21.6 144.54 95.59 22.84 RW-9721-5158 Dual Pole Dish 28631 22.6 181.97 95.59 22.84 RW-9732-4958 Dual Pole Dish 321585 18.6 72.44 95.59 22.84

COVER PAGE Test of AP0127730, AP0134760 To: FCC 47 CFR Part 90, Subpart Y; IC RSS 111 Test Report Serial No.: RDWN12-U4 Rev A TEST REPORT FROM Test of AP0127730, AP0134760 To FCC 47 CFR Part 90, Subpart Y; IC RSS 111 Test Report Serial No.: RDWN12-U4 Rev A This report supersedes NONE Manufacturer: RADWIN Ltd 27 Habarzel Street Tel Aviv, 69710 Israel Product Function:5 GHz 2x2 MIMO RF Module Copy No: pdf Issue Date: 28th November 2012 This Test Report is Issued Under the Authority o f; MiCOM Labs, Inc. 440 Boulder Cour t, Suite 200 Pleasanton, CA 94566 USA Phone: +1 (925) 462-0304 Fax: +1 (925) 462-0306 www.micomlabs.com TEST CERTIFICATE #2381.01 MiCOM Labs is an ISO 17025 Accredited Testing Laboratory Title: To: AP0127730, AP0134760 FCC 47 CFR Part 90, Subpart Y; IC RSS 111 Serial #: Issue Date: Page: RDWN12- U4 Rev A 28th November 2012 3 of 109 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs p ersonnel. Any changes will be noted in the Document History section of the report. MiCOM Labs, 440 Boulder Court, Suite 200, Pleasanton, CA 94566 USA, Phone: 925.462.0304, Fax: 925.462.0306, www.micomlabs.com This page has been left intentionally blank Title: AP0127730, AP0134760 To: Serial #: Issue Date: Page: FCC 47 CFR Part 90, Subpart Y; IC RSS 111 RDWN12- U4 Rev A 28th November 2012 4 of 109 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs p ersonnel. Any changes will be noted in the Document History section of the report. MiCOM Labs, 440 Boulder Court, Suite 200, Pleasanton, CA 94566 USA, Phone: 925.462.0304, Fax: 925.462.0306, www.micomlabs.com TABLE OF CONTENTS ACCREDITATION, LISTINGS & RECOGNITION ..........................................................5 TESTING ACCREDITATION ........................................................................................... 5 RECOGNITION................................................................................................................ 6 PRODUCT CERTIFICATION........................................................................................... 7 1. TEST RESULT CERTIFICATE .................................................................................9 2. REFERENCES AND MEASUREMENT UNCERTAINTY ......................................10 2.1. Normative References .......................................................................................... 10 2.2. Test and Uncertainty Procedures ......................................................................... 11 3. PRODUCT DETAILS AND TEST CONFIGURATIONS ........................................12 3.1. Technical Details .................................................................................................. 12 3.2. Scope of Test Program ......................................................................................... 13 3.3. Equipment Model(s) and Serial Number(s) .......................................................... 17 3.4. Antenna Details .................................................................................................... 17 3.5. Cabling and I/O Ports ........................................................................................... 18 3.6. Test Configurations............................................................................................... 18 3.7. Equipment Modifications....................................................................................... 19 3.8. Deviations from the Test Standard ....................................................................... 19 3.9. Subcontracted Testing or Third Party Data .......................................................... 19 4. TEST SUMMARY ....................................................................................................20 5. TEST RESULTS ......................................................................................................21 5.1. Device Characteristics .......................................................................................... 21 5.1.1. Occupied Bandwidth and Emission Mask ............................................. 21 5.1.2. Peak Output Power ............................................................................... 42 5.1.3. Peak Power Spectral Density (PPSD)................................................... 47 5.1.4. Maximum Permissible Exposure ........................................................... 67 5.1.5. Frequency Stability; Temperature Variations, and Voltage Variations .. 69 5.1.6. Spurious Emissions at Antenna Terminals - Transmitter ...................... 87 5.1.7. Radiated Spurious Emissions ............................................................... 95 5.1.8. Receiver Radiated Spurious Emissions (above 1 GHz)...................... 101 6. TEST SET-UP PHOTOGRAPHS..........................................................................106 6.1. Conducted Measurement Test Set-Up ............................................................... 106 6.2. Radiated Spurious Emissions ............................................................................. 107 7. TEST EQUIPMENT DETAILS...............................................................................108 Title: AP0127730, AP0134760 To: Serial #: Issue Date: Page: FCC 47 CFR Part 90, Subpart Y; IC RSS 111 RDWN12- U4 Rev A 28th November 2012 5 of 109 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs p ersonnel. Any changes will be noted in the Document History section of the report. MiCOM Labs, 440 Boulder Court, Suite 200, Pleasanton, CA 94566 USA, Phone: 925.462.0304, Fax: 925.462.0306, www.micomlabs.com ACCREDITATION, LISTINGS & RECOGNITION TESTING ACCREDITATION MiCOM Labs, Inc. is an accredited Electrical testing laboratory per the international standard EN ISO/IEC 17025. The company is accredited by the American Association for Laboratory Accreditation (A2LA) www.a2la.org test labora…

Text truncated - open the document above for the full version.