Q3QHOK6321RFID Tag Reader

R12 Tablet PC Model R001 R12-Series SlateMate BCS/HF RFID/Serial Model RPM001 R12-Series SlateMate HF RFID/Serial Model RPM002 Important Product Information Safety and Regulatory Compliance Limited Warranty Informations importantes sur le produit Respect des normes de sécurité et des réglementations Garantie limitée Wichtige Produktinformationen Sicherheits- und Vorschriftseinhaltungserklärung Eingeschränkte Gewährleistung Información importante del producto Conformidad normativa y de seguridad Garantía limitada Informações importantes sobre o produto Conformidade regulatória e de segurança Garantia limitada 2 R001 Safety and Regulatory Guide English This document contains regulatory, precautionary, and recycling information for the Motion R001 Tablet PC. To avoid injury, read this document and understand its contents before you use the Tablet PC. Keep this document nearby, so you can refer to it later. For detailed operating instructions and safety information, see www.motioncomputing.com/us/support/userdocs. The Motion Tablet PC model R001 is marketed and/or known as the R12. Note: The Motion Tablet PC model R001 is compliant to the UL 60950-1, 2nd ed., CSA 22.2 No. 60950-1-07 and IEC/ EN60950-1:2006+A12:2011 Safety Standard for Information Technology Equipment. Symbol description The following symbols may appear on the products or accessories. Specifications Product safety information Motion Tablet PCs are designed to optimize safety, minimize strain, and withstand the rigors of portability. However, to further reduce the risk of injury or damage to the unit, you should observe certain precautions. Mounting and installation disclaimer Motion Computing shall not be liable under any theory of liability (including, without limitation, contract, tort, or statutory law) for any loss, damage, personal injury, or other damage of any nature (including, without limitation, direct, special, incidental, or consequential damages) arising directly or indirectly as a result of improper or inappropriate placement, installation, or use of its products or any other application. To safely install and use Motion products, full consideration of occupants, systems (e.g., the location of fuel lines, navigation systems, brakes lines, electrical, drive train or other systems), air-bags and other back-up, warning, or safety equipment is required. Without limiting the foregoing, Motion specifically disclaims any responsibility for the placement, use, or installation of its products not consistent with (i) the original manufacturer’s or governmental or regulatory specifications and recommendations for the environment where the products will be placed, used, or installed, (ii) Motion written product instruction sheets, or (iii) workmanship standards. Federal Communications Commission Compliance with Nemko CCL for general product safety in accordance with UL 60950-1 (ITE) and CAN/CSA C22.2 No. 60950-1 (ITE) Canada Interference-Causing Equipment Standard #3 Class B devices Compliance with R&TTE Directive 1999/5/EC for radio frequency devices Conformité Européne; compliance to EMC and Low Voltage Directives of the European Union Product complies with 2002/ 96/EC Compliance with the Independent Communications Authority of South Africa Compliance with Australian and New Zealand EMC, EMR, Radio communication, and Te le co m m u ni c a ti o n Standards (A-Tick symbol) Compliance with the Korea Certification Commission for EMC, Safety, and Te le co m m u ni c a ti o n s Canada ICES-003,Class B Infocomm Development Authority for Singapore Normalizacion Y Certification Electronica A.C. (NYCE) Instituto Argentino de Normalización y Certificación (IRAM) Agência Nacional de Te l e co m u ni c a çõ e s (A N AT E L ) OnOff (Storage) Te m p e ra tu re5– 45 ° C 0–45° C (with SSD option) -20–60° C Humidity8–90% RH5–95% RH Air pressure697–1060 hPa187–1060 hPa Power supply (ITE) Delta Electronics, SADP-65WH Rev. BB Input: 1.5 A, 100–240 VAC, 47–63 Hz Output: 19 V DC, 3.42 A The power supply is compliant with UL 60950-1, CAN/CSA C22.2 No. 60950-1, and IEC/EN 60950-1 NYCE MR R001 Safety and Regulatory Guide 3 Setup precautions Review the following setup precautions: •Read the installation instructions before connecting the Tablet PC to the power supply. •If you put the Tablet PC in a docking station, place it on a level surface so it does not fall over and damage the unit, the docking station, or other components. •When you move the Tablet PC between environments with very different humidity and/or temperature ranges, allow sufficient time to adjust to the new humidity or temperature. •Do not drop the Tablet PC or subject it to other mechanical shocks as this can cause cosmetic imperfections and/or system malfunctions. •Do not apply heavy pressure to the Tablet PC or subject it to strong impact. Excessive pressure or impact can cause damage to Tablet PC components or otherwise cause malfunctions. •Do not use the Tablet PC AC adapter for other equipment. This can generate heat or fire. In addition, do not use other AC adapters with the Tablet PC. •When using the Tablet PC for long periods of time, rest your eyes for approximately 10 to 15 minutes every hour. Failing to rest your eyes can cause eye strain and other deterioration of eye health. Basic personal safety precautions Review the following personal safety precautions: •Do not attempt to service the Tablet PC or its components yourself. Perform only those service procedures for which Motion provides special instructions, for example, hot-swapping a battery or installing a peripheral device. •Turn off the Tablet PC completely to clean it, its components, or chassis, or perform operations requiring similar steps. To do this, turn off the power switch, then disconnect the AC adapter from the electrical outlet. •Do not operate the Tablet PC near water, such as near a bathtub, kitchen sink or laundry tub, in a wet basement, by a swimming pool, or in the rain while plugged into an ele…

Text truncated - open the document above for the full version.

March 17, 2014 Federal Communications Commission 445 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement Re: We, Motion Computing, hereby authorized Intertek Testing Services to act as our agent for the purpose of preparing application for FCC ID number Q3QHOK6321 under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is February 1, 2014. The limited agency agreement expires on June 1, 2014 unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, John A. Nagy International Regulatory Compliance Manager Motion Computing, Inc. 8601 RR2222, Building II Austin, TX 78717 [email protected] 512 637-1143(office) 512 627-3787 (cell)

Attention: Application Examiner Re: Request for confidentiality Applicant: Motion Computing, Inc. FCC ID: Q3QHOK6321 To whom it may concern, Permanent Confidentiality Request is hereby submitted by Motion Computing to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential: • Schematics • Detailed Block diagrams • Parts list • Operational Description Motion Computing has invested considerable time and materials in research and development to produce the referenced product. Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. Sincerely, John A. Nagy International Regulatory Compliance Manager Motion Computing, Inc. 8601 RR2222, Building II Austin, TX 78717 [email protected] 512 637-1143(office), 512 627-3787 (cell) 1(1)

PIM Module Installed on Tablet PIM Module Installed on Tablet

The Personality Modules (RPM001 and RPM002) are permanently attached to the Tablet (R001) at the Factory or qualified Service Center. When attached the PEMs label with the FCC and IC ID are included in the battery bay of the tablet. The Labeling instructions are provided. The Tablet (R001) label is also included for your reference. Daisy_Dai 01/24-14” Jassy_Huo 01/24-14” ZSX00 LABEL LABEL 12A PEM 030-05-0291-A00 100% A4 00 00 SIZE 2014 / 02 / 23 ITEMSSPEC. PART NO. MATERIAL REMARK 1. USE WATER DISSOVING INK, INK CONTAINS HEAVY METAL IS PROHIBITED. 2. PIECE BY PIECE HG12A000100 SIZE THICKNESS(±0.02MM) COLOR:MATERIAL PRINTING GROSS WEIGHT 0.142(INCLUDE ADHESIVE) COATING L20×W20 (+0,-0.2MM) 0.17 (± 50%G) ADHESIVE ACRYLIC ADHESIVE SILVER MATT MOTION MARIN MIDNIGHT, PANTONE COOL GRAY 4C 25μ MATT OPP FILM 75μ METALIZED POLYESTER LABEL (SILVER MATT) SIZE:100% Module Bottom View (backside) 20 20 LBL P/N: 030-05-0291-A00 FCC ID: Q3QHOK6321 IC : 4587A- HOK6321 Supplier Instruction, R12-Series System Labels Document Number: 002-01-0335 Revision History Name Date ECN # - General Statement of Change Version Debra Dresser 12/04/2013 ECN 3393 – Initial Release A00 Debra Dresser 02/05/2014 ECN 3406 – Update WWAN ROW Regulatory label part number A01 Debra Dresser 02/17/2014 ECN 3414 – (1) Add SlateMate (PEM) Label part numbers in Section 1.3 and (2) Remove i3 Intel Logo Label References in Section 1.3 and Table 1 A02 Debra Dresser 03/11/2014 ECN 3434 – Update IMEI Label size from 50x6mm to 50x15mm in Section 2.2.2 A03 PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO MOTION COMPUTING AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT FOR WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF MOTION COMPUTING. Supplier Instruction for R12-Series System Labels Motion Computing Confidential ii Document No. 002-01-0335 Table of Contents REVISION HISTORY ................................................................................................................................................ I TABLE OF CONTENTS .......................................................................................................................................... II 1. INTRODUCTION ............................................................................................................................................. 1 1.1 PURPOSE ..................................................................................................................................................... 1 1.2 SCOPE ......................................................................................................................................................... 1 1.3 REFERENCE DOCUMENTS ........................................................................................................................... 1 2. SYSTEM LABELING REQUIREMENTS ..................................................................... .........................1 2.1 GENERAL REQUIREMENTS ................................................................................................1 2.2 R12-SERIES.................................................................................................................3 2.2.1 SYSTEM FRONT................................................................................................................3 2.2.2 SYSTEM BACK.................................................................................................................4 Supplier Instruction for R12-Series System Labels Motion Computing Confidential 1 Document No. 002-01-0335 1 Introduction 1.1 Purpose This document specifies system labeling requirements for the R12-Series products. 1.2 Scope This instruction is applicable to the R12-Series systems. 1.3 Reference Documents The following documents can be referenced for further information: - Bill of Materials for the series referenced above for specific part numbers of the items - R12 Cosmetic Specification, 002-09-0040 - PPID Specification, 030-02-0007 - R12 Serial Number Specification, 002-09-0041 - Microsoft GML Label Drawing:  030-08-0067 Label, Microsoft, Windows 8.1 GML, R12-Series - Intel Logo Label Drawings:  030-08-0065 Label, Tablet, Intel Core, Haswell, i5 Processor, Vertical  030-08-0066 Label, Tablet, Intel Core, Haswell, i7 Processor, Vertical - Motion Label Drawings:  030-08-0049 Label, Create Recovery Media Alert, HDD Recovery  030-05-0281 Label, Regulatory, Sierra Wireless, WWAN, North America  030-05-0290 Label, Regulatory, Sierra Wireless, WWAN, ROW  030-05-0285 Label, Regulatory, Intel WLAN/BT Combo, AC7260, R12  030-05-0291 Label, Regulatory, SlateMate, BCS/HF RFID/Serial, R12- Series  030-05-0292 Label, Regulatory, SlateMate, HF RFID/Serial, R12-Series - Brazil Anatel Label Drawing:  030-05-0282 Label, Regulatory, Brazil, MGI Tech, R12 - Costa Rica Sutel Label Drawing:  030-05-0283 Label, Regulatory, SUTEL, Costa Rica, R12 2 System Labeling Requirements 2.1 General Requirements 2.1.1 Apply adequate pressure to affix labels securely, evenly, and completely to the surface. 2.1.2 Ensure labels are aligned and within the allowed parameters of the cosmetic specification. Supplier Instruction for R12-Series System Labels Motion Computing Confidential 2 Document No. 002-01-0335 2.1.3 Apply the appropriate Intel Logo Label according to Table 1 and Microsoft Logo Label according to Table 2. TABLE 1 Intel Logo Label for Tablet Placement Processors R12 (Como) i5 CPU i7 CPU Any Wireless Solution TABLE 2 Genuine Microsoft Logo (GML) Label for Tablet Placement Windows 8 Image Supplier Instruction for R12-Series System Labels Motion Computing Confidential 3 Document No. 002-01-0335 2.2 R12-Series 2.2.1 System Front Supplier Instruction for R12-Series System Labels Motion Computing Confidential 4 Document No. 002-01-0335 2.2.2 System Back Label Placement inside the battery bays:

Serial board Bar Code reader RFID reader (6321) Serial board bottom Bar Code Logic USB Connector Board

This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. EMC Report for Motion Computing on the Como Tablet Page 1 of 18 731 Enterprise Drive Lexington, KY 40510 Telephone: 859-226-1000 Facsimile: 859-226-1040 www.intertek-etlsemko.com TEST REPORT Report Number: 101488929LEX-002 Project Number: G101488929 Report Issue Date: 3/16/2014 Product Name: Como Tablet FCCID: Q3QHOK6321 ICID: 4587A-HOK6321 FCC Standards: Industry Canada Standards: CFR Title 47 Part 15 Subpart C RSS-210 Issue 8 Tested by: Client: Intertek Testing Services NA, Inc. 731 Enterprise Drive Lexington, KY 40510 Motion Computing 8601 Ranch Road 2222 Bldg #2 Austin , TX 78730 Report prepared by Report reviewed by Bryan Taylor, Team Leader Jason Centers, Senior Project Engineer Intertek Report Number: 101488929LEX-002 Issued: 3/16/2014 EMC Report for Motion Computing on the Como Tablet FCCID:Q3QHOK6321; ICID:4587A-HOK6321 Page 2 of 18 TABLE OF CONTENTS 1 Introduction and Conclusion .............................................................................................................. 3 2 Test Summary ...................................................................................................................................... 3 3 Description of Equipment Under Test ............................................................................................... 4 4 20dB Bandwidth ................................................................................................................................... 6 5 In-Band Radiated Spurious Emissions (Transmitter) ...................................................................... 7 6 Out of Band Radiated Spurious Emissions (Transmitter) ............................................................... 9 7 AC Powerline Conducted Emissions ............................................................................................... 11 8 Frequency Stability ............................................................................................................................ 15 9 Antenna Requirement per FCC Part 15.203 ..................................................................................... 16 10 Measurement Uncertainty.............................................................................................................. 17 11 Revision History ............................................................................................................................. 18 Intertek Report Number: 101488929LEX-002 Issued: 3/16/2014 EMC Report for Motion Computing on the Como Tablet FCCID:Q3QHOK6321; ICID:4587A-HOK6321 Page 3 of 18 1 Introduction and Conclusion The tests indicated in section 2 were performed on the product constructed as described in section 3. The remaining test sections are the verbatim text from the actual data sheets used during the investigation. These test sections include the test name, the specified test method, a list of the actual test equipment used, documentation photos, results and raw data. No additions, deviations, or exclusions have been made from the standard(s) unless specifically noted. Based on the results of our investigation, we have concluded the product tested complied with the requirements of the standard(s) indicated. The results obtained in this test report pertain only to the item(s) tested. The INTERTEK-Lexington is located at 731 Enterprise Drive, Lexington Kentucky, 40510. The radiated emission test site is a 10-meter semi-anechoic chamber. The chamber meets the characteristics of CISPR 16-1 and ANSI C63.4. For measurements, a remotely controlled flush-mount metal-top turntable is used to rotate the EUT a full 360 degrees. A remote controlled non-conductive antenna mast is used to scan the antenna height from one to four meters. The test site is listed with the FCC under registration number 485103. The test site is listed with Industry Canada under site number IC 2042M-1. 2 Test Summary Page Test Name FCC Reference IC Reference Result 6 20dB Bandwidth § 2.1049 RSS-GEN (4.6.1) Pass 7 In-Band Radiated Spurious Emissions (Transmitter) § 15.225(a)(b)(c) RSS-210 (A2.6) Pass 9 Out of Band Radiated Spurious Emissions (Transmitter) § 15.225(d), § 15.209 RSS-210 (A2.6) Pass 11 AC Powerline Conducted Emissions § 15.107, § 15.207 RSS-Gen (7.2.4) Pass 15 Frequency Stability § 15.225(e) RSS-210 (A2.6) Pass 16 Antenna Requirement per FCC Part 15.203 § 15.203 RSS-Gen (7.1.2) Pass Intertek Report Number: 101488929LEX-002 Issued: 3/16/2014 EMC Report for Motion Computing on the Como Tablet FCCID:Q3QHOK6321; ICID:4587A-HOK6321 Page 4 of 18 3 Description of Equipment Under Test Equipment Under Test Manufacturer Motion Computing Model Number Como Tablet Serial Number Test Sample #1 FCC Identifier Q3QHOK6321 IC Identifier 4587A-HOK6321 Receive Date 2/3/2014 Test Start Date 3/6/2014 Test End Date 3/16/2014 Device Received Condition Good Test Sample Type Production Frequency Band 13.56MHz Mode(s) of Operation RFID Transmission Control Normal Operation Antenna Type (15.203) Internal Power Supply 19VDC (Via AC / DC power adapter) Description of Equipment Under Test The Como Tablet is a …

Text truncated - open the document above for the full version.