Q87-03530Linksys MAX-STREAM AC1900+ WiFi Range Extender

MAX-STREAM ™ AC1900+ Wi-Fi RANGE EXTENDER Regulatory and Warranty Information RE7000 .3".3" .3".3" 1 WIRELESS REGULATORY INFORMATION FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and devices • Connect the equipment to an outlet other than the receiver’s • Consult a dealer or an experienced radio/TV technician for assistance FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. IEEE 802.11b or 802.11g operation of this product in the USA is firmware-limited to channels 1 through 11. The device for the band 5150-5250 MHz is only for indoor usage to reduce the potential for harmful interference to co-channel mobile satellite systems. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 35 cm between the radiator and your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. Innovation, Science and Economic Development Canada Statement CAN ICES-3 (B)/NMB-3 (B) This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. 2 For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology. Innovation, Science and Economic Development Canada Radiation Exposure Statement Industry Canada Radiation Exposure Statement This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 35 cm between the radiator and your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with ISED multi-transmitter product procedures. Restrictions in the 5 GHz Band The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile satellite systems. This device has been designed to operate with an antenna having a maximum gain of 3.31 dBi and 3.38 dBi at 2.4 GHz and 5 GHz respectively. Antenna having a higher gain is strictly prohibited per regulations of ISED. The required antenna impedance is 50 ohms. The maximum antenna gain (Please see the table below) permitted (for devices in the bands 5250-5350 MHz and 5470-5725 MHz) to comply with the EIRP limit and because high power radars are allocated as primary users (meaning they have priority) in 5250-5350 MHz and 5650-5850 MHz, these radars could cause interference and/or damage to license exempt LAN devices. No.Antenna TypeFor 2.4 GHz Gain (peak)For 5 GHz Gain (peak)Antenna Connector 1METALN/A3.19 dBiswitch 2PCB3.28 dBi3.38 dBiI-PEX 3PCB3.31 dBi3.22 dBiI-PEX 4METALN/A3.16 dBiswitch Additional requirements for the band 5600-5650 MHz Until further notice, devices subject to this section shall not be capable of transmitting in the band 5600-5650 MHz, so that Environment Canada weather radars operating in this band are protected. 3 Avis d’Innovation, Sciences et Développement économique Canada CAN ICES-3 (B)/NMB-3 (B). L’exploitation est autorisée seulement aux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) il doit accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Pour les produits disponibles sur le marché aux États-Unis et au Canada, seuls les canaux de 1 à 11 peuvent être utilisés. La sélection d’autres canaux n’est pas possible. Le dispositif peut automatiquement cesser d’émettre en cas d’absence d’informations à transmettre, ou à cause d’une défaillance technique. Notez que l’objet n’est pas d’interdire la transmission des informations de contrôle ou de signalisation ou l’utilisation de codes répétitifs lorsque requis par la technologie. Avis d’Innovation, Sciences et Développement économique Canada concernant l’exposition aux radiofréquences Ce matériel est conforme aux limites établies par ISED en matière d’exposition aux radiofréquences dans un environnement non contrôlé. Ce matériel doit être installé et utilisé à une distance d’au moins 3…

Text truncated - open the document above for the full version.

Indicator LED Indicator LED Indicator LED 1 Plug the range extender into an electrical outlet close to your router. You can move the range extender to an ideal location later in step 5. After being plugged in, the indicator LED on the front of your range extender will start to blink green for up to a minute. Wi-Fi Protected Setup (WPS) Setting up as a wireless range extender Get started There are two ways to use your Linksys extender: as a wireless range extender or as a wired range extender (access point). Wireless range extenders boost Wi-Fi range for better coverage and increased signal strength. Wired range extender (access points) create new Wi-Fi hotspots when connected to a router or access point with an Ethernet cable. Both scenarios require a router with a working Internet connection. Before starting setup, decide whether you want to use your RE7000 as a wireless range extender or as a wired range extender (access point). Instructions for both setups are in this guide. • The indicator LED on the front of the range extender gives you information about power, updating and signal strength. 3 4 Connect to Linksys Extender Setup network. On a computer, phone or tablet, connect to the Wi-Fi network: Linksys Extender Setup - XXX. (XXX are the last three digits of your range extender’s MAC address.) Launch setup Enter http://extender.linksys.com (or try http://192.168.1.1) in a browser to complete setup. Be sure to choose “As a wireless range extender” when asked how you want to use your range extender. Follow the on-screen instructions to select your network to extend, customize your extended network name and password and find the best spot using Spot Finder Technology. Connect your Wi-Fi devices to the extended network you just created. Select the extended network on your device’s Wi-Fi manager. Use this setup method if you don’t have a WPS button on your router, or if you don’t want to use WPS to set up your RE7000. Frequently asked questions (FAQ) Why can I not find “Linksys Extender Setup - XXX” in my Wi-Fi list? Make sure the indicator LED on the range extender is blinking orange. If you still can’t see the setup network, move the device being used for setup closer to the range extender. Wait for a blinking orange LED and refresh the Wi-Fi list. On browser-based setup, why do I not see the setup screen on http://extender. linksys.com? On your device’s Wi-Fi manager, make sure “Linksys Extender Setup - XXX” is selected, then refresh your browser. On browser-based setup, why can I not see my network name on the “Choose your wireless” page? Your range extender might be too far from the router. Move it closer and refresh the list. I correctly entered my network password during browser-based setup. Why does the “Enter your password” page still show an error? The range extender likely is at the outside limit of the router's signal. The signal could be getting interrupted before your password makes it to the router. Move your range extender closer to the router. Why can’t I connect my range extender with WPS? There are a number of reasons that WPS could fail: • Your router and range extender are too far apart • The two-minute connection window expired • The WPS button on either range extender or router did not depress all the way • WPS is disabled on the router • MAC filtering is enabled on the router How do I reset the range extender to factory defaults? Using a paperclip or safety pin, press the reset button on the side of the range extender and hold until the indicator LED starts blinking green. Why am I experiencing poor signal and slow speed on my range extender? Be sure that you’ve placed your range extender in an ideal location, as indicated by Spot Finder Technology. NOTE: When you move around your home, your wireless devices may not disconnect from the router until they lose the Wi-Fi signal. This may occur even if the Wi-Fi signal from the range extender signal is stronger (and vice versa). If you are having connection issues, select the network with the stronger signal. For advanced configuration, consult the user guide at linksys.com/support/re7000. 8820-02381 Rev. C00 Write down the extended network names and passwords you just created. Extended network names and passwords 2.4 GHz password 2.4 GHz network name 5 GHz network name Range extender admin password Write down your range extender admin password. You'll need the range extender admin password if you want to access your range extender settings. Admin password Get Help Internet: linksys.com/support/RE7000 Twitter: @LinksysCares Phone (US/Canada): 800-326-7114 (complimentary for 90 days from date of original purchase) 7 1 Plug in the range extender. Plug in the range extender midway between your router and the area without Wi-Fi. Using your mobile device or laptop, be sure you have at least two bars (around 50%) of your router’s Wi-Fi signal at that location. If you don’t have two bars, move the range extender closer to the router. You can move the range extender to an ideal location later using the setup software. Browser-based setup WPS is a simple way to connect Wi-Fi devices with Push Button Connect. Routers that support WPS have a button that might look like one of these symbols: NOTE — The WPS button will not work if you have disabled WPS on your router, or if you have chosen WEP as your network security type. In either case, continue with browser-based setup below. Ye s Continue with Wi-Fi Protected Setup (WPS) below No (or not sure) Continue with Browser- based setup, also in this Quick Start Guide 2 Wait for the indicator LED on the front of your range extender to start to blink orange before going to step 3. This can take up to a minute. 4 Extend your 5 GHz network. You may skip this step if your router does not have a 5 GHz network or if you don’t want to extend that network. a. Press the WPS button on the side of your router again. Within the next two minutes complete step 4b. b. Press the WPS button on your …

Text truncated - open the document above for the full version.

LINKSYS LLC 121 Theory Drive Irvine California 92617 United States Tel: 949-238-4518 Date: 2020-04-23 FCC ID: Q87-03530 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Test Setup photos User’s manual Internal Photos Sincerely yours, ----------------------------------- Po-Wen Cheng LINKSYS LLC Tel: 949-238-4518 E-mail: [email protected]

LINKSYS LLC 121 Theory Drive Irvine California 92617 United States Tel: 949-238-4518 Date: 2020-04-23 FCC ID: Q87-03530 AUTHORIZATION LETTER To Whom It May Concern: LINKSYS LLC hereby authorizes Andrea Hsia / Supervisor of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to the Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Andrea Hsia / Supervisor of BV CPS Taoyuan on LINKSYS LLC’s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, ----------------------------------------------- Po-Wen Cheng LINKSYS LLC Tel: 949-238-4518 E-mail: [email protected]

Reference No.: 200107C19 Page 1 of 3 CONSTRUCTION PHOTOS OF EUT Model: RE7000 V2 / Brand: LINKSYS Reference No.: 200107C19 Page 2 of 3 Reference No.: 200107C19 Page 3 of 3

FCC ID: Q87-03530 IC: 3839A-03530 Rear View

Reference No.: 200107C19 Page 1 of 9 CONSTRUCTION PHOTOS OF EUT Model: RE7000 V2 / Brand: LINKSYS Reference No.: 200107C19 Page 2 of 9 Reference No.: 200107C19 Page 3 of 9 Reference No.: 200107C19 Page 4 of 9 Reference No.: 200107C19 Page 5 of 9 Reference No.: 200107C19 Page 6 of 9 Reference No.: 200107C19 Page 7 of 9 Reference No.: 200107C19 Page 8 of 9 Reference No.: 200107C19 Page 9 of 9

Report No.: SA200107C19 Page No. 1 / 6 Report Format Version: 6.1.1 RF Exposure Report Report No.: SA200107C19 FCC ID: Q87-03530 Test Model: RE7000 V2, RE6900, RE7100 Received Date: Jan. 07, 2020 Date of Evaluation: Jan. 30, 2020 Issued Date: Feb. 04, 2020 Applicant: LINKSYS LLC Address: 121 Theory Drive Irvine California 92617 United State Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: SA200107C19 Page No. 2 / 6 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 2.4 Calculation Result of Maximum Conducted Power ............................................................................. 6 Report No.: SA200107C19 Page No. 3 / 6 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued SA200107C19 Original Release Feb. 04, 2020 Report No.: SA200107C19 Page No. 4 / 6 Report Format Version: 6.1.1 1 Certificate of Conformity Product: Linksys MAX-STREAM AC1900+ WiFi Range Extender Brand: LINKSYS Test Model: RE7000 V2, RE6900, RE7100 Sample Status: Engineering Sample Applicant: LINKSYS LLC Date of Evaluation: Jan. 30, 2020 Standards: FCC Part 2 (Section 2.1091) References Test Guidance : KDB 447498 D01 General RF Exposure Guidance v06 IEEE C95.3 -2002 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date: Feb. 04, 2020 Rona Chen / Specialist Approved by : , Date: Feb. 04, 2020 Dylan Chiou / Senior Project Engineer Report No.: SA200107C19 Page No. 5 / 6 Report Format Version: 6.1.1 2 RF Exposure 2.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f 2 )* 30 30-300 27.5 0.073 0.2 30 300-1500 ... ... f/1500 30 1500-100,000 ... ... 1.0 30 f = Frequency in MHz ; *Plane-wave equivalent power density 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 24cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA200107C19 Page No. 6 / 6 Report Format Version: 6.1.1 2.4 Calculation Result of Maximum Conducted Power Band Frequency Band (MHz) Max Power (dBm) Antenna Gain (dBi) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) WLAN 2412-2462 25.12 6.31 24 0.192 1.00 5180-5240 26.85 8.94 24 0.524 1.00 5745-5825 28.42 9.06 24 0.773 1.00 Note: 1. Determining compliance based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. 2. 2.4GHz: Directional gain = 10log[(10 G1/20 + 10 G2/20 + .... + 10 GN/20 ) 2 / N ANT ] = 6.31 dBi 5GHz: U-NII-1 Band: Directional gain = 10log[(10 G1/20 + 10 G2/20 + .... + 10 GN/20 ) 2 / N ANT ] = 8.94 dBi U-NII-3 Band: Directional …

Text truncated - open the document above for the full version.

Report No.: RF200107C19-1 Page No. 1 / 75 Report Format Version:6.1.2 FCC Test Report Report No.: RF200107C19-1 FCC ID: Q87-03530 Test Model: RE7000 V2 Series Model: RE6900, RE7100 (Refer to Section 3.1 for more details) Received Date: Jan. 07, 2020 Test Date: Jan. 14, 2020 ~ Jan. 17, 2020 Issued Date: Feb. 04, 2020 Applicant: LINKSYS LLC Address: 121 Theory Drive Irvine California 92617 United State Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location : No.19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF200107C19-1 Page No. 2 / 75 Report Format Version:6.1.2 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ........................................................................................................................... 5 2 Summary of Test Results ........................................................................................................................... 6 2.1 Measurement Uncertainty ..................................................................................................................... 6 2.2 Modification Record .............................................................................................................................. 6 3 General Information ................................................................................................................................... 7 3.1 General Description of EUT .................................................................................................................. 7 3.2 Description of Test Modes ..................................................................................................................... 9 3.2.1 Test Mode Applicability and Tested Channel Detail .................................................................. 10 3.3 Duty Cycle of Test Signal .................................................................................................................... 12 3.4 Description of Support Units ............................................................................................................... 13 3.4.1 Configuration of System under Test ......................................................................................... 13 3.5 General Description of Applied Standards and References ............................................................... 14 4 Test Types and Results ............................................................................................................................ 15 4.1 Radiated Emission and Bandedge Measurement .............................................................................. 15 4.1.1 Limits of Radiated Emission and Bandedge Measurement ..................................................... 15 4.1.2 Limits of Unwanted Emission Out of the Restricted Bands ...................................................... 16 4.1.3 Test Instruments ....................................................................................................................... 17 4.1.4 Test Procedures ........................................................................................................................ 18 4.1.5 Deviation from Test Standard ................................................................................................... 18 4.1.6 Test Setup ................................................................................................................................. 19 4.1.7 EUT Operating Conditions ........................................................................................................ 20 4.1.8 Test Results .............................................................................................................................. 21 4.2 Conducted Emission Measurement .................................................................................................... 40 4.2.1 Limits of Conducted Emission Measurement ........................................................................... 40 4.2.2 Test Instruments ....................................................................................................................... 40 4.2.3 Test Procedures ............................................…

Text truncated - open the document above for the full version.

Report No.: RF200107C19 1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: RF200107C19 2 RADIATED EMISSION TEST BELOW 1GHz (Z-Plane) Report No.: RF200107C19 3 RADIATED EMISSION TEST ABOVE 1GHz (Z-Plane)