Q87-EA2700Linksys EA2700 Dual-Band N600 Router with Gigabit

User Guide Linksys EA-Series i Table of Contents Linksys EA-Series i Product overview EA2700/EA3500 1 Back view 1 Bottom view 1 EA4500 2 Top view 2 Back view 2 Setting Up Your EA-Series Router Where to find more help 3 How to set up your router 3 How to start Cisco Connect 3 Use Cisco Connect to manage your router 3 How to manually set up your router 3 Advanced Configuration How to open the browser-based utility 4 Setup > Basic Setup 5 Language 5 Internet Setup 5 Wireless > Wireless Settings 6 Wireless Settings 6 Wireless Security Wireless > Wireless Security 7 Personal options 7 Office options 7 Option settings 7 Troubleshooting How to run Cisco Connect after setup 10 Your router was not successfully set up 11 Get Windows XP Service Pack 3 message 11 Your Internet cable is not plugged in message 12 Cannot access your router message 13 Device not found message 14 Specifications Linksys EA2700 16 Linksys EA3500 17 Linksys EA4500 18 Table of Contents 1 Product overview Linksys EA-Series 1 Product overview EA2700/EA3500 Back view Ethernet portsWi-Fi Protected Setup button Internet port Power port Power indicatorUSB port (EA3500 only) Your router’s appearance may vary •USB port (EA3500 only)—To easily share disk storage with other users on your network or on the Internet, connect a USB drive to this port •Ethernet ports—Connect Ethernet cables (also called network cables) to these Gigabit (10/100/1000) ports, color coded blue, and to other wired Ethernet network devices on your network •Internet port—Connect an Ethernet cable (also called a network or Internet cable) to this port, color coded yellow, and to your modem Wi-Fi Protected Setup™ button—Press this button to easily configure wireless security on Wi-Fi Protected Setup-enabled network devices For more information, see “Wireless Security” on page 8 •Power indicator—Stays on steadily while power is connected and following a successful Wi-Fi Protected Setup connection Flashes slowly during bootup, during firmware upgrades, and during a Wi-Fi Protected Setup connection Flashes quickly when there is a Wi-Fi Protected Setup error •Power—Connect the included AC power adapter to this port CAUTIon Use only the adapter that came with your router •Power button—Press | (on) to turn on the router Bottom view Your router’s appearance may vary •Reset button—Press and hold this button for 5-15 seconds (until the port lights flash at the same time) to reset the router to its factory defaults You can also restore the defaults using the browser-based utility 2 Product overview Linksys EA-Series EA4500 Top view Indicator light •Indicator light—Stays on steadily while power is connected and following a successful Wi-Fi Protected Setup connection Pulses slowly during bootup, during firmware upgrades, and during a Wi-Fi Protected Setup connection Flashes quickly when there is a Wi-Fi Protected Setup error Back view Ethernet ports Wi-Fi Protected Setup button Internet portPower port Reset button USB port •Ethernet ports—Connect Ethernet cables (also called network cables) to these Gigabit (10/100/1000) ports, color coded blue, and to other wired Ethernet network devices on your network •Internet port—Connect an Ethernet cable (also called a network or Internet cable) to this port, color coded yellow, and to your modem •Wi-Fi Protected Setup™ button—Press this button to easily configure wireless security on Wi-Fi Protected Setup-enabled network devices For more information, see “Wireless Security” on page 8 •USB port—To easily share disk storage with other users on your network or on the Internet, connect a USB drive to this port •Reset button—Press and hold this button for 5-15 seconds (until the port lights flash at the same time) to reset the router to its factory defaults You can also restore the defaults using the browser-based utility •Power—Connect the included AC power adapter to this port CAUTIon Use only the adapter that came with your router •Power button—Press | (on) to turn on the router 3 Setting Up Your EA-Series Router Linksys EA-Series 3 Where to find more help In addition to this User Guide, you can find help at these locations: •Linksys.com/support (documentation, downloads, FAQs, technical support, live chat, forums) •Cisco Connect help (run Cisco Connect, then click Learn More where available) •Browser-based utility context-sensitive help (open the utility, then click Help in the right-side column ) How to set up your router The easiest and fastest way to set up your router is to run the Cisco Connect setup software How to start Cisco Connect When you run the setup CD, Cisco Connect (your router’s setup software) is automatically installed onto your computer You can then use Cisco Connect to easily manage your router noTE: If you lose your setup CD, you can download the software from Linksys.com/support To start Cisco Connect for the first time: 1. Insert the CD into your CD or DVD drive 2. Click Set up your Linksys Router If you do not see this: •For Windows, click Start, Computer, then double-click the CD drive and the Setup icon •For Mac, double-click the CD icon on your desktop, then double-click the Setup icon 3. Follow the on-screen instructions to complete your router setup Use Cisco Connect to manage your router After your router has been set up and Cisco Connect has been installed, you can use Cisco Connect to easily manage many of your router’s settings such as: •Connect devices to your network •Test your Internet connection speed •Configure parental controls •Set up guest access •Change your router’s name and password How to manually set up your router After setting up the router with the setup software (located on the CD), the router will be ready for use If you would like to change its advanced settings, or if the software does not run, use the router’s browser-based utility You can access the utility with a web browser on a computer connected to the router For more information on using the utility, see “How to open the brow…

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT EUT with adapter Model: CAP012121 US EUT with adapter Model: CAD1212C Page 2 EUT with adapter Model: MU12-G120100-A1 Page 3 Page 4 Page 5 Page 6 Page 7

BACK Label location

Page 8 Main source Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16 Page 17 Second source Page 18 Page 19 Page 20 Page 21 Page 22 Page 23 Page 24 Page 25

Report No.: SA111219C11 1 Report Format Version 4.0.0 RF EXPOSURE REPORT REPORT NO.: SA111219C11 MODEL NO.: EA2700 FCC ID: Q87-EA2700 RECEIVED: Dec. 19, 2011 TESTED: Dec. 20, 2011 ~ Jan. 17, 2012 ISSUED: Jan. 18, 2012 APPLICANT: Cisco Consumer Products LLC ADDRESS: 121 Theory Drive Irvine California 92617 United States ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 6 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval or endorsement by any government agency. The test results in the report only apply to the tested sample. Report No.: SA111219C11 2 Report Format Version 4.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD.............................................................................................3 1. CERTIFICATION..........................................................................................................4 2. RF EXPOSURE ...........................................................................................................5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) .....................................5 2.2 MPE CALCULATION FORMULA.................................................................................5 2.3 CLASSIFICATION .......................................................................................................5 2.4 CACLULATION RESULT OF MAXIMUM CONDUCTED POWER ..............................6 Report No.: SA111219C11 3 Report Format Version 4.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED Original release N/A Jan. 18, 2012 Report No.: SA111219C11 4 Report Format Version 4.0.0 1. CERTIFICATION PRODUCT: Linksys EA2700 Dual-Band N600 Router with Gigabit MODEL: EA2700 BRAND: CISCO APPLICANT: Cisco Consumer Products LLC TESTED: Dec. 20, 2011 ~ Jan. 17, 2012 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: EA2700) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE:Jan. 18, 2012 Ivy Lin / Specialist APPROVED BY : , DATE:Jan. 18, 2012 Gary Chang / Technical Manager Report No.: SA111219C11 5 Report Format Version 4.0.0 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE calculation Formula Pd = (Pout*G) / (4*pi*r2) where Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA111219C11 6 Report Format Version 4.0.0 2.4 CACLULATION RESULT OF MAXIMUM CONDUCTED POWER FREQUENCY BAND (MHz) MAX CONDUCTED POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 27.38 3.45 20 0.241 1 5180-5240 15.84 3.62 20 0.018 1 5745-5825 26.73 5.15 20 0.307 1 CONCULSION: Both of the WLAN 2.4G & 5.0G can transmit simultaneously, the formula of calculated the MPE is: CPD1 / LPD1 + CPD2 / LPD2 + ......etc. < 1 CPD = Calculation power density LPD = Limit of power density 1. WLAN 2.4G + WLAN 5.0G = 0.241 + 0.307 = 0.548 Therefore, the maximum calculation of this situation is 0.548, which is less than the “1” limit.

Report No.: RF111219C11 1 Report Format Version 4.1.0 FCC TEST REPORT (15.247) REPORT NO.: RF111219C11 MODEL NO.: EA2700 FCC ID: Q87-EA2700 RECEIVED: Dec. 19, 2011 TESTED: Dec. 20, 2011 ~ Jan. 17, 2012 ISSUED: Jan. 18, 2012 APPLICANT: Cisco Consumer Products LLC ADDRESS: 121 Theory Drive Irvine California 92617 United States ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 89 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. Report No.: RF111219C11 2 Report Format Version 4.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD.............................................................................................5 1. CERTIFICATION..........................................................................................................6 2. SUMMARY OF TEST RESULTS .................................................................................7 2.1 MEASUREMENT UNCERTAINTY...............................................................................7 3. GENERAL INFORMATION ..........................................................................................8 3.1 GENERAL DESCRIPTION OF EUT ............................................................................8 3.2 DESCRIPTION OF TEST MODES ............................................................................ 11 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST .......................................................12 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............................13 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ...........................................17 3.4 DESCRIPTION OF SUPPORT UNITS ......................................................................17 4. TEST TYPES AND RESULTS (FOR 2.4GHz BAND) ................................................18 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT....................................18 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .................18 4.1.2 TEST INSTRUMENTS...............................................................................................19 4.1.3 TEST PROCEDURES ...............................................................................................20 4.1.4 DEVIATION FROM TEST STANDARD......................................................................20 4.1.5 TEST SETUP.............................................................................................................21 4.1.6 EUT OPERATING CONDITIONS ..............................................................................21 4.1.7 TEST RESULTS ........................................................................................................22 4.2 CONDUCTED EMISSION MEASUREMENT ............................................................36 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT..........................................36 4.2.2 TEST INSTRUMENTS...............................................................................................36 4.2.3 TEST PROCEDURES ...............................................................................................37 4.2.4 DEVIATION FROM TEST STANDARD......................................................................37 4.2.5 TEST SETUP.............................................................................................................38 4.2.6 EUT OPERATING CONDITIONS ..............................................................................38 4.2.7 TEST RESULTS ........................................................................................................39 4.3 6dB BANDWIDTH MEASUREMENT.........................................................................43 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ......................................................43 4.3.2 TEST SETUP.............................................................................................................43 4.3.3 TEST INSTRUMENTS...............................................................................................43 4.3.4 TEST PROCEDURE..................................................................................................43 4.3.5 DEVIATION FROM TEST STANDARD......................................................................43 4.3.6 EUT OPERATING CONDITIONS ..............................................................................43 4.3.7 TEST RESULTS ........................................................................................................44 4.4 CONDUCTED OUTPUT POWER..............................................................................45 4.4.1 LIMITS OF CONDUCTED OUTPUT POWER MEASUREMENT ..............................45 4.4.2 TEST SETUP.............................................................................................................45 Report No.: RF111219C11 3 Report Format Version 4.1.0 4.4.3 TEST INSTRUMENTS...............................................................................................45 4.4.4 TEST PROCEDURES ...............................................................................................45 4.4.5 DEVIATION FROM TEST STANDARD......................................................................45 4.4.6 EUT OPERATING CONDITIONS ..............................................................................45 4.4.7 TEST RESULTS ................................................................................................…

Text truncated - open the document above for the full version.

Report No.: RF111219C11-1 1 Report Format Version 4.1.0 FCC TEST REPORT (15.407) REPORT NO.: RF111219C11-1 MODEL NO.: EA2700 FCC ID: Q87-EA2700 RECEIVED: Dec. 19, 2011 TESTED: Dec. 21, 2011 ~ Jan. 17, 2012 ISSUED: Jan. 18, 2012 APPLICANT: Cisco Consumer Products LLC ADDRESS: 121 Theory Drive Irvine California 92617 United States ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 57 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. Report No.: RF111219C11-1 2 Report Format Version 4.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD.............................................................................................4 1. CERTIFICATION..........................................................................................................5 2. SUMMARY OF TEST RESULTS .................................................................................6 2.1 MEASUREMENT UNCERTAINTY...............................................................................6 3. GENERAL INFORMATION ..........................................................................................7 3.1 GENERAL DESCRIPTION OF EUT ............................................................................7 3.2 DESCRIPTION OF TEST MODES ..............................................................................9 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST .........................................................9 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............................10 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ...........................................12 3.4 DESCRIPTION OF SUPPORT UNITS ......................................................................12 4. TEST TYPES AND RESULTS ...................................................................................13 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT....................................13 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .................13 4.1.2 LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS .............13 4.1.3 TEST INSTRUMENTS...............................................................................................14 4.1.4 TEST PROCEDURES ...............................................................................................15 4.1.5 DEVIATION FROM TEST STANDARD......................................................................15 4.1.6 TEST SETUP.............................................................................................................16 4.1.7 EUT OPERATING CONDITION.................................................................................16 4.1.8 TEST RESULTS ........................................................................................................17 4.2 CONDUCTED EMISSION MEASUREMENT ............................................................27 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT..........................................27 4.2.2 TEST INSTRUMENTS...............................................................................................27 4.2.3 TEST PROCEDURES ...............................................................................................28 4.2.4 DEVIATION FROM TEST STANDARD......................................................................28 4.2.5 TEST SETUP.............................................................................................................29 4.2.6 EUT OPERATING CONDITIONS ..............................................................................29 4.2.7 TEST RESULTS ........................................................................................................30 4.3 PEAK TRANSMIT POWER MEASUREMENT ..........................................................34 4.3.1 LIMITS OF PEAK TRANSMIT POWER MEASUREMENT ........................................34 4.3.2 TEST SETUP.............................................................................................................34 4.3.3 TEST INSTRUMENTS...............................................................................................34 4.3.4 TEST PROCEDURE..................................................................................................35 4.3.5 DEVIATION FROM TEST STANDARD......................................................................35 4.3.6 EUT OPERATING CONDITIONS ..............................................................................35 4.3.7 TEST RESULTS ........................................................................................................36 4.4 PEAK POWER EXCURSION MEASUREMENT .......................................................38 4.4.1 LIMITS OF PEAK POWER EXCURSION MEASUREMENT.....................................38 Report No.: RF111219C11-1 3 Report Format Version 4.1.0 4.4.2 TEST SETUP.............................................................................................................38 4.4.3 TEST INSTRUMENTS...............................................................................................38 4.4.4 TEST PROCEDURE..................................................................................................38 4.4.5 DEVIATION FROM TEST STANDARD......................................................................38 4.4.6 EUT OPERATING CONDITIONS ..............................................................................38 4.4.7 TEST RESULTS ..............…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST