Q87-PLW400Powerline AV Wireless Network Extender

Linksys Powerline Networking PLW400, PLWK400 (PLW400+PLE400) Regulatory Information Table of ContentsLinksys Powerline Networking Table of Contents Wireless Regulatory Information 1 FCC Statement 1 FCC Radiation Exposure Statement 1 Safety Notices 1 Industry Canada Statement 1 Avis d’Industrie Canada 1 Wireless Disclaimer 2 Avis de non-responsabilité concernant les appareils sans fil 2 Declaration of Conformity with Regard to EU Directive 1999/5/EC (R&TTE Directive) 2 Wireless Equipment (Wireless-N/G/A/B Products) 3 National Restrictions 3 Product Usage Restrictions 4 Technical Documents on http://home cisco com/wireless 4 WEEE Information 5 User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE) 5 1 Linksys Powerline NetworkingWireless Regulatory Information Wireless Regulatory Information FCC Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna •Increase the separation between the equipment or devices •Connect the equipment to an outlet other than the receiver’s •Consult a dealer or an experienced radio/TV technician for assistance FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter IEEE 802 11b or 802 11g operation of this product in the USA is firmware-limited to channels 1 through 11 Safety Notices WARNING: Do not use this product near water, for example, in a wet basement or near a swimming pool WARNING: Avoid using this product during an electrical storm There may be a remote risk of electric shock from lightning WARNING: This product contains lead, known to the State of California to cause cancer, and birth defects or other reproductive harm Wash hands after handling Industry Canada Statement This Class B digital apparatus complies with Canadian ICES-003 and RSS210 Operation is subject to the following two conditions: 1 This device may not cause interference and 2 This device must accept any interference, including interference that may cause undesired operation of the device To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication Industry Canada Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter Avis d’Industrie Canada Cet appareil numérique de la classe B est conforme aux normes NMB-003 et RSS210 du Canada L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : 1 il ne doit pas produire de brouillage et 2 il doit accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif Afin de réduire les interférences avec d’autres systèmes, le choix du type d’antenne et de son gain doivent respecter la limite de P I R E (Puissance Isotrope Rayonnée Équivalente) requise pour un fonctionnement adéquat 2 Linksys Powerline NetworkingWireless Regulatory Information Avis d’Industrie Canada concernant l’exposition aux radiofréquences : Ce matériel est conforme aux limites établies par IC en matière d’exposition aux radiofréquences dans un environnement non contrôlé Ce matériel doit être installé et utilisé à une distance d’au moins 20 cm entre l’antenne et le corps de l’utilisateur L’émetteur ne doit pas être placé près d’une autre antenne ou d’un autre émetteur, ou fonctionner avec une autre antenne ou un autre émetteur Wireless Disclaimer The maximum performance for wireless is derived from IEEE Standard 802 11 specifications Actual performance can vary, including lower wireless network capacity, data throughput rate, range and coverage Performance depends on many factors, conditions and variables, including distance from the access point, volume of network traffic, building materials and construction, operating system used, mix of wireless products used, interference and other adverse conditions Avis de non-responsabilité concernant les appareils sans fil Les performances maximales pour les réseaux sans fil sont tirées des spécifications de la norme IEEE 802 11 Les performances réelles peuvent varier, notamment en fonction de la capacité du réseau sans fil, du débit de la transmission de données, de la portée et de la couverture Les performances dépe…

Text truncated - open the document above for the full version.

Report No.:111202C19 1 CONSTRUCTION PHOTOS OF EUT Report No.:111202C19 2

Report No.:111202C19 3 Report No.:111202C19 4 Report No.:111202C19 5 Report No.:111202C19 6 Report No.:111202C19 7

Report No.: SA111202C19 Report Format Version 4.0.0 1 RF EXPOSURE REPORT REPORT NO.: SA111202C19 MODEL NO.: PLW400 FCC ID: Q87-PLW400 RECEIVED: Dec. 04, 2011 TESTED: Dec. 14, 2011 ISSUED: Jan. 09, 2012 APPLICANT: Cisco Consumer Products LLC ADDRESS: 121 Theory Drive Irvine California 92617 United States ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan This test report consists of 5 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement. The test results in the report only apply to the tested sample. Report No.: SA111202C19 Report Format Version 4.0.0 2 TABLE OF CONTENTS RELEASE CONTROL RECORD....................................................................................3 1. CERTIFICATION......................................................................................................4 2. RF EXPOSURE LIMIT..............................................................................................5 3. MPE CALCULATION FORMULA.............................................................................5 4. CLASSIFICATION....................................................................................................5 5. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER...........................5 Report No.: SA111202C19 Report Format Version 4.0.0 3 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA111202C19 Original release Jan. 09, 2012 Report No.: SA111202C19 Report Format Version 4.0.0 4 1. CERTIFICATION PRODUCT: Powerline AV Wireless Network Extender BRAND NAME: CISCO MODEL NO.: PLW400 TEST SAMPLE: ENGINEERING SAMPLE APPLICANT: Cisco Consumer Products LLC TESTED: Dec. 14, 2011 STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: PLW400) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: Jan. 09, 2012 ( Midoli Peng, Specialist ) APPROVED BY : , DATE: Jan. 09, 2012 ( May Chen, Deputy Manager ) Report No.: SA111202C19 Report Format Version 4.0.0 5 2. RF EXPOSURE LIMIT LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 3. MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 4. CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. 5. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER FREQUENCY BAND (MHz) MAX POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 414.4 2.48 20 0.146 1.00 --- END ---

Report No.: RF111202C19 1 Report Format Version 4.0.0 FCC TEST REPORT REPORT NO.: RF111202C19 MODEL NO.: PLW400 FCC ID: Q87-PLW400 RECEIVED: Dec. 04, 2011 TESTED: Dec. 13 to 20, 2011 ISSUED: Jan. 09, 2012 APPLICANT: Cisco Consumer Products LLC ADDRESS: 121 Theory Drive Irvine California 92617 United States ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan This test report consists of 78 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF111202C19 2 Report Format Version 4.0.0 Table of Contents RELEASE CONTROL RECORD..............................................................................4 1. CERTIFICATION...........................................................................................5 2. SUMMARY OF TEST RESULTS...................................................................6 2.1 MEASUREMENT UNCERTAINTY................................................................7 3. GENERAL INFORMATION...........................................................................8 3.1 GENERAL DESCRIPTION OF EUT..............................................................8 3.2 DESCRIPTION OF TEST MODES..............................................................10 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL..............11 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS.............................14 3.4 DESCRIPTION OF SUPPORT UNITS........................................................15 3.5 CONFIGURATION OF SYSTEM UNDER TEST.........................................16 4. TEST TYPES AND RESULTS.....................................................................17 4.1 CONDUCTED EMISSION MEASUREMENT..............................................17 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT............................17 4.1.2 TEST INSTRUMENTS................................................................................17 4.1.3 TEST PROCEDURES.................................................................................18 4.1.4 DEVIATION FROM TEST STANDARD.......................................................18 4.1.5 TEST SETUP..............................................................................................19 4.1.6 EUT OPERATING CONDITIONS................................................................19 4.1.7 TEST RESULTS..........................................................................................20 4.2 RADIATED EMISSION MEASUREMENT...................................................22 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT.................................22 4.2.2 TEST INSTRUMENTS................................................................................23 4.2.3 TEST PROCEDURES.................................................................................24 4.2.4 DEVIATION FROM TEST STANDARD.......................................................24 4.2.5 TEST SETUP..............................................................................................25 4.2.6 EUT OPERATING CONDITIONS................................................................25 4.2.7 TEST RESULTS..........................................................................................26 4.3 6dB BANDWIDTH MEASUREMENT..........................................................55 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT........................................55 4.3.2 TEST INSTRUMENTS................................................................................55 4.3.3 TEST PROCEDURE...................................................................................55 4.3.4 DEVIATION FROM TEST STANDARD.......................................................55 4.3.5 TEST SETUP..............................................................................................55 4.3.6 EUT OPERATING CONDITIONS................................................................55 4.3.7 TEST RESULTS..........................................................................................56 4.4 MAXIMUM PEAK OUTPUT POWER..........................................................60 Report No.: RF111202C19 3 Report Format Version 4.0.0 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT...........60 4.4.2 INSTRUMENTS..........................................................................................60 4.4.3 TEST PROCEDURES.................................................................................60 4.4.4 DEVIATION FROM TEST STANDARD.......................................................60 4.4.5 TEST SETUP..............................................................................................60 4.4.6 EUT OPERATING CONDITIONS................................................................60 4.4.7 TEST RESULTS..........................................................................................61 4.5 POWER SPECTRAL DENSITY MEASUREMENT......................................63 4.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT...................63 4.5.2 TEST INSTRUMENTS................................................................................63 4.5.3 TEST PROCEDURE...................................................................................63 4.5.4 DEVIATION FROM TEST STANDARD.......................................................63 4.5.5 TEST S…

Text truncated - open the document above for the full version.

Report No.: 111013E05 1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: 111013E05 2 RADIATED EMISSION TEST (below 1GHz) Report No.: 111013E05 3 RADIATED EMISSION TEST (above 1GHz)