Q87-RE1000Wireless-N Extender

Linksys E3000 High Performance Wireless-N Router Linksys RE1000 Wireless-N Extender User Guide Linksys RE1000Table of Contents i Wireless-N Extender Contents Chapter 1: Product Overview 1 Front 1 To p 1 Bottom 2 Chapter 2: Advanced Configuration 3 How to Access the Browser-Based Utility 3 How to Use the Browser-Based Utility 3 Setup > Basic Setup 4 Wireless > Site Survey 5 Wireless > Basic Wireless Settings 5 Wireless > Wireless Security 8 Wireless > QoS 9 Administration > Management 10 Administration > Log 10 Administration > Diagnostics 10 Administration > Factory Defaults 11 Status > Device Information 13 Status > Ethernet Statistics 13 Status > WLAN Statistics 14 Appendix F: Specifications 15 Linksys RE1000Chapter 1: Product Overview 1 Wireless-N Extender Chapter 1: Product Overview Thank you for choosing the Linksys RE1000 Wireless-N Extender The Extender lets you repeat the wireless signal of any Access Point or Router to provide Internet connectivity in hard to reach areas via a wireless connection or through its Ethernet port Various security features help protect your data and your privacy while you are online Security features include Wi-Fi Protected Access 2 (WPA2) security, which encrypts data on your wireless network Setup and use of the router is easy using Cisco Connect, the software that is installed when you run the included CD Advanced configuration of the router is available through the provided browser-based utility Alternatively, you can use WPS to add the RE1000 to your existing network, if your Access Point or Router supports this feature Front This light indicates power or Wi-Fi Protected Setup status If you have client devices, such as wireless printers, that support Wi-Fi Protected Setup, then you can use Wi-Fi Protected Setup to automatically configure wireless security for your wireless network To use Wi-Fi Protected Setup, refer to “Wi-Fi Protected Setup” on page 12 Power (white) When the router is powered on, resets to factory defaults, or upgrades its firmware, the light flashes slowly (every three seconds) When the router is ready for use, the light is continuously lit If there is an error, the light flashes quickly (every second); disconnect the power adapter from your router, wait two seconds, and then reconnect the power adapter to your router Wi-Fi Protected Setup (white) When the Wi-Fi Protected Setup process is active, the light flashes slowly (every two seconds) for two minutes When the Wi-Fi Protected Setup is successful, the light is continuously lit If there is an error, the light flashes quickly (every second) for two minutes; please wait and try again To p Wi-Fi Protected Setup Button If you have client devices, such as wireless printers, that support Wi-Fi Protected Setup, then you can use Wi-Fi Protected Setup to automatically configure wireless security for your wireless network To use Wi-Fi Protected Setup, refer to “Wi-Fi Protected Setup” on page 12 Reset This button allows you to reset the router to its factory defaults Press and hold the Reset button for approximately five seconds As an alternative, you can restore the defaults from the Administration > Factory Defaults screen in the router’s browser-based utility (refer to “Administration > Factory Defaults” on page 42) Linksys RE1000Chapter 1: Product Overview 2 Wireless-N Extender Power Switch Only featured in the European versions of the RE1000 Bottom Ethernet (green) Using Ethernet cables (also called network cables), this Ethernet port connects Ethernet network devices to your wireless network The green light turns on when an Ethernet device is connected and active on this port 3 Wireless-N Extender Linksys RE1000Chapter 2: Advanced Configuration Chapter 2: Advanced Configuration After setting up the Extender with the setup software (located on the CD-ROM), the Extender will be ready for use If you would like to change its advanced settings, use the Extender’s browser-based utility This chapter describes each web page of the utility and each page’s key functions You can access the utility via a web browser on a computer connected to the Extender How to Access the Browser-Based Utility To access the browser-based utility, launch the web browser on your computer, and enter the Extender’s default Internet Protocol (IP) address, 192.168.1.1, in the Address field Then press Enter This works only if your Extender has not been configured If your Extender has been configured, log into your access point or router User Interface, look for the status page, locate the DHCP table using the user manual of your access point or router, and look for RE1000 in the DHCP table The IP address should show up , make a note of it , and then enter it in your web browser link address Then press Enter NOTE: You can also access the browser-based utility on Windows computers by looking up the UPnP network devices Double click on the RE1000 icon A login screen appears (A similar screen appears for non-Windows 7 users ) Login Screen 1 In the User name field, enter admin 2 In the Password field, enter the password created by the setup software If you did not run the setup software, then enter the default, admin NOTE: You can set a new password on the Administration > Management screen Refer to “Administration > Management” on page 40 3 Click OK to continue NOTE: You can also access the browser-based utility through Cisco Connect How to Use the Browser-Based Utility Use the tabs at the top of each screen to navigate within the utility The tabs are arranged in two levels, top-level tabs for general functions and lower-level tabs for the corresponding specific functions Top- and Lower-Level Tabs The top-level tabs are: Setup, Wireless, Security, Administration, and Status Each of these has its own unique, lower-level tabs NOTE: Within this User Guide, each screen is identified by its top- and lower-level tab names For example, “Setup > Basic Setup” is the screen accessed via the Setup top-level tab, and its Basic Se…

Text truncated - open the document above for the full version.

Linksys E3000 High Performance Wireless-N Router Supplemental Information Linksys RE1000 Wireless-N Extender Regulatory Information Table of Contents i Wireless-N Extender Linksys RE1000 Table of Contents Wireless Regulatory Information 1 FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 FCC Radiation Exposure Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Avis d’Industrie Canada. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Wireless Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Avis de non-responsabilité concernant les appareils sans fil . . . . . . . . . . . . . . . . . . 2 Declaration of Conformity with Regard to EU Directive 1999/5/EC (R&TTE Directive) . . . 2 Wireless Equipment (Wireless-N/G/A/B Products) . . . . . . . . . . . . . . . . . . . . . . . . . 3 National Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Product Usage Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Technical Documents on http://home.cisco.com/wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 WEEE Information 5 User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1 Wireless-N Extender Linksys RE1000Wireless Regulatory Information Wireless Regulatory Information FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: sReorient or relocate the receiving antenna sIncrease the separation between the equipment or devices sConnect the equipment to an outlet other than the receiver’s sConsult a dealer or an experienced radio/TV technician for assistance FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11b or 802.11g operation of this product in the USA is firmware-limited to channels 1 through 11. Safety Notices WARNING: Do not use this product near water, for example, in a wet basement or near a swimming pool. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. WARNING: This product contains lead, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. Industry Canada Statement This Class B digital apparatus complies with Canadian ICES-003 and RSS210. Operation is subject to the following two conditions: 1. This device may not cause interference and 2. This device must accept any interference, including interference that may cause undesired operation of the device. This device has been designed to operate with an antenna having a maximum gain of 1.5 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. Industry Canada Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Avis d’Industrie Canada Cet appareil numérique de la classe B est conforme aux normes NMB-003 et RSS210 du Canada. L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : 1. il ne doit pas produire de brouillage et 2. il doit accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Le dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximum de 1,5 dBi. Les règlements d’Industrie Canada interdisent strictement l’utilisation d’antennes dont le gain est supérieur à cette limite. L’impédance requise de l’antenne est de 50 ohms. 3 dBi 3 dBi. 2 Wireless-N Extender Linksys RE1000Wireless Regulatory Information Avis d’Industrie Canada concernant l’exposition aux radiofréquences : Ce matériel est conforme aux limites établies par IC en matière d’exposition aux radiofréquences dans un environnement non contrôlé. Ce maté…

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT

FCC ID：Q87-RE1000 LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device.

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3 Page 4 Page 5 Page 6

FCC ID: Q87-RE1000 Report No.: RF110420E03 Operational Description This device is a Wireless-N Extender operates in the 2.4GHz band, which the maximum data rate could be up to 270Mbps which OFDM technique. If the signal to noise ratio is too poor which could not support 270Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by internal power supply. The antennas are Dipole antennas without antenna connector. The other instruction, please have a look at the users manual.

Report No.: SA110420E03 Report Format Version 4.0.0. 1 RF EXPOSURE REPORT REPORT NO.: SA110420E03 MODEL NO.: RE1000 FCC ID: Q87-RE1000 ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT: Cisco Consumer Products LLC ADDRESS: 121 Theory Drive Irvine, CA 92617(USA) ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan Report No.: SA110420E03 Report Format Version 4.0.0. 2 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA110420E03 Original release May 18, 2011 Report No.: SA110420E03 Report Format Version 4.0.0. 3 1.CERTIFICATION PRODUCT: Wireless-N Extender BRAND NAME: Cisco MODEL NO.: RE1000 TEST SAMPLE: ENGINEERING SAMPLE APPLICANT: Cisco Consumer Products LLC STANDARDS: IEEE C95.1 The above equipment (Model: RE1000) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: May 18, 2011 (Carol Liao, Specialist ) APPROVED BY : , DATE: May 18, 2011 ( May Chen, Deputy Manager ) Report No.: SA110420E03 Report Format Version 4.0.0. 4 2.RF Exposure Limit LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 3.MPE calculation Formula Pd = (Pout*G) / (4*pi*r2) where Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 4.Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. 5.Calculation result of maximum conducted power FREQUENCY BAND (MHz) MAX POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 550.8 3 20 0.219 1.00 ---END---

Report No.: RF110420E03 1 Report Format Version 4.0.0 FCC TEST REPORT REPORT NO.: RF110420E03 MODEL NO.: RE1000 FCC ID: Q87-RE1000 RECEIVED: Mar. 23, 2011 TESTED: Mar. 23 to May 06, 2011 ISSUED: May 18, 2011 APPLICANT: Cisco Consumer Products LLC ADDRESS: 121 Theory Drive Irvine, CA 92617(USA) ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan This test report consists of 84 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF110420E03 2 Report Format Version 4.0.0 Table of Contents RELEASE CONTROL RECORD........................................................................................4 1. CERTIFICATION....................................................................................................5 2. SUMMARY OF TEST RESULTS............................................................................6 2.1 MEASUREMENT UNCERTAINTY..........................................................................7 3. GENERAL INFORMATION.....................................................................................8 3.1 GENERAL DESCRIPTION OF EUT.......................................................................8 3.2 DESCRIPTION OF TEST MODES.......................................................................10 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL........................11 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS.......................................13 3.4 DESCRIPTION OF SUPPORT UNITS..................................................................14 3.5 CONFIGURATION OF SYSTEM UNDER TEST...................................................15 4. TEST TYPES AND RESULTS..............................................................................17 4.1 CONDUCTED EMISSION MEASUREMENT........................................................17 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT......................................17 4.1.2 TEST INSTRUMENTS..........................................................................................17 4.1.3 TEST PROCEDURES..........................................................................................18 4.1.4 DEVIATION FROM TEST STANDARD.................................................................18 4.1.5 TEST SETUP.......................................................................................................19 4.1.6 EUT OPERATING CONDITIONS.........................................................................19 4.1.7 TEST RESULTS...................................................................................................20 4.2 RADIATED EMISSION MEASUREMENT.............................................................22 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT...........................................22 4.2.2 TEST INSTRUMENTS..........................................................................................23 4.2.3 TEST PROCEDURES..........................................................................................25 4.2.4 DEVIATION FROM TEST STANDARD.................................................................25 4.2.5 TEST SETUP.......................................................................................................26 4.2.6 EUT OPERATING CONDITIONS.........................................................................27 4.2.7 TEST RESULTS...................................................................................................28 4.3 6dB BANDWIDTH MEASUREMENT....................................................................57 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT..................................................57 4.3.2 TEST INSTRUMENTS..........................................................................................57 4.3.3 TEST PROCEDURE.............................................................................................57 4.3.4 DEVIATION FROM TEST STANDARD.................................................................57 4.3.5 TEST SETUP.......................................................................................................57 4.3.6 EUT OPERATING CONDITIONS.........................................................................57 4.3.7 TEST RESULTS...................................................................................................58 4.4 MAXIMUM PEAK OUTPUT POWER....................................................................62 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT.....................62 4.4.2 INSTRUMENTS....................................................................................................62 4.4.3 TEST PROCEDURES..........................................................................................62 Report No.: RF110420E03 3 Report Format Version 4.0.0 4.4.4 DEVIATION FROM TEST STANDARD.................................................................62 4.4.5 TEST SETUP.......................................................................................................62 4.4.6 EUT OPERATING CONDITIONS.........................................................................62 4.4.7 TEST RESULTS...................................................................................................63 4.5 POWER SPECTRAL DENSITY MEASUREMENT.....................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST(Below 1GHz) 3 RADIATED EMISSION TEST(Above 1GHz)