Q87-RE1000V2Wireless-N Range Extender

Linksys RE1000 Regulatory Information Contents i Linksys RE1000 Table of Contents Regulatory Information 1 FCC Statement 1 FCC Radiation Exposure Statement 1 Safety Notices 1 Safety guidelines 1 Industry Canada Statement 2 Avis d’Industrie Canada 2 Wireless Disclaimer 2 Avis de non-responsabilité concernant les appareils sans fil 2 Mexico 2 Declaration of Conformity with Regard to EU Directive 1999/5/EC (R&TTE Directive) 3 Wireless Equipment (Wireless-AC/N/G/A/B Products) 4 National Restrictions 4 Product Usage Restrictions 5 Technical Documents on www myciscohome com 5 WEEE Information 6 User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE) 6 1 Linksys RE1000Regulatory Information Regulatory Information FCC Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna •Increase the separation between the equipment or devices •Connect the equipment to an outlet other than the receiver’s •Consult a dealer or an experienced radio/TV technician for assistance FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter IEEE 802 11b or 802 11g operation of this product in the USA is firmware-limited to channels 1 through 11 Safety Notices WARNING: Do not use this product near water, for example, in a wet basement or near a swimming pool WARNING: Avoid using this product during an electrical storm There may be a remote risk of electric shock from lightning WARNING: This product contains lead, known to the State of California to cause cancer, and birth defects or other reproductive harm Wash hands after handling Safety guidelines WARNING: Use the following safety guidelines to ensure your own personal safety and to help protect your product from potential damage To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment, observe the following precautions Do not service this product except as explained in your system documentation If any of the following conditions occur, unplug the product from the electrical outlet and replace the part or contact your service provider/retailer: •The power cable or plug is damaged •An object has fallen into the product •The product has been exposed to water •The product has been dropped or damaged •The product does not operate correctly when you follow the operating instructions Keep your system away from radiators and heat sources Install product in a manner and location to assure ventilation openings are not blocked Do not spill food or liquids on your system components, and never operate the product in a wet environment If the system gets wet, contact your service provider/retailer Do not push any objects into the openings of your system Doing so can cause fire or electric shock by shorting out interior components Operate the product only from the type of external power source indicated on the electrical ratings label Be sure that attached devices are electrically rated to operate with the power available in your location 2 Linksys RE1000Regulatory Information Position system cables and power cables carefully; route cables so that they cannot be stepped on or tripped over Be sure that nothing rests on any cables Do not modify power cables or plugs Always follow your local and national wiring rules Industry Canada Statement This Class B digital apparatus complies with Canadian ICES-003 and RSS210 Operation is subject to the following two conditions: 1 This device may not cause interference and 2 This device must accept any interference, including interference that may cause undesired operation of the device This device has been designed to operate with an antenna having a maximum gain of 1 5 dBi Antenna having a higher gain is strictly prohibited per regulations of Industry Canada The required antenna impedance is 50 ohms Industry Canada Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter Avis d’Industrie Canada Cet appareil numérique de la classe B est conforme aux normes NMB-003 et RSS210 du Canada L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : 1 il ne doit pas produire de brouillage et 2 il doit accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptibl…

Text truncated - open the document above for the full version.

Cisco Consumer Products LLC 121 Theory Drive Irvine, CA 92617 (USA) Phone: 949-261-1288 Fax: 949-823-3002 D ate: 2013-04-03 Re: Supersede request for FCC ID: Q 87-RE1000V2; Granted on 01/23/2013 To Whom It May Concern: We regret to inform you that due to Modified FCC website information : Add version 2 in the FCC webside, we have submitted the wrong test report exhibit to the filing. To prevent misunderstanding to the public, we would like to request the FCC to supersede the exhibit described as test report. If you have any questions, feel free to contact us. Thank you. Darrell Tennis ------------------------------------------------------ Darrell Tennis S enior Manager, Global Compliance Cisco Consumer Products LLC Phone: 949-910-7048 Fax: 949-823-3002 [email protected]

Report No.: 121204E06 1 of 10 CONSTRUCTION PHOTOS OF EUT EUT (White) Report No.: 121204E06 2 of 10 EUT (Black) Report No.: 121204E06 9 of 10 Report No.: 121204E06 10 of 10

Material: PC + (T=0.3mm)

Report No.: 121204E06 3 of 10 Report No.: 121204E06 4 of 10 Report No.: 121204E06 5 of 10 Report No.: 121204E06 6 of 10 Report No.: 121204E06 7 of 10 Report No.: 121204E06 8 of 10

FCC ID: Q87-RE1000V2 IC ID: 3839A-RE1000V2 Report No.: RF121204E06 IC121204E06 Operational Description This device is a Wireless-N Range Extender, which operates in 2.4GHz bands; the maximum data rate could be up to 300Mbps which OFDM technique. If the signal to noise ratio is too poor which could not support 300Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by a 12Vdc power adapter. The antenna is a PIFA antenna. The other instruction, please have a look at the users manual.

Report No.: SA121204E06 R1 1 of 6 Report Format Version 5.0.0 Cancels and replaces the report No.: SA121204E06 dated Jan. 17, 2013 RF EXPOSURE REPORT REPORT NO.: SA121204E06 R1 MODEL NO.: RE1000 VERSION: 2 FCC ID: Q87-RE1000V2 RECEIVED: Dec. 04, 2012 TESTED: Dec. 20, 2012 ISSUED: Feb. 26, 2013 APPLICANT: Cisco Consumer Products, LLC ADDRESS: 121 Theory Drive Irvine, CA 92617(USA) ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: SA121204E06 R1 2 of 6 Report Format Version 5.0.0 Cancels and replaces the report No.: SA121204E06 dated Jan. 17, 2013 TABLE OF CONTENTS RELEASE CONTROL RECORD ..................................................................................... 3 1. CERTIFICATION ...................................................................................................... 4 2. RF EXPOSURE LIMIT .............................................................................................. 5 3. MPE CALCULATION FORMULA ............................................................................. 5 4. CLASSIFICATION .................................................................................................... 5 5. ANTENNA GAIN....................................................................................................... 5 6. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ........................... 6 Report No.: SA121204E06 R1 3 of 6 Report Format Version 5.0.0 Cancels and replaces the report No.: SA121204E06 dated Jan. 17, 2013 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA121204E06 Original release Jan. 17, 2013 SA121204E06 R1 Added version information on page 1 & 4 Feb. 26, 2013 Report No.: SA121204E06 R1 4 of 6 Report Format Version 5.0.0 Cancels and replaces the report No.: SA121204E06 dated Jan. 17, 2013 1. CERTIFICATION PRODUCT: Wireless-N Range Extender BRAND NAME: Cisco MODEL NO.: RE1000 VERSION: 2 TEST SAMPLE: ENGINEERING SAMPLE APPLICANT: Cisco Consumer Products, LLC TESTED DATE: Dec. 20, 2012 STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: RE1000) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: Oct. 26, 2012 ( Lori Chung, Specialist ) APPROVED BY : , DATE: Oct. 26, 2012 ( May Chen, Deputy Manager ) Report No.: SA121204E06 R1 5 of 6 Report Format Version 5.0.0 Cancels and replaces the report No.: SA121204E06 dated Jan. 17, 2013 2. RF EXPOSURE LIMIT LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 3. MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 4. CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. 5. ANTENNA GAIN Transmitter Circuit Antenna Type Gain (dBi) Connector type Frequency range (MHz to MHz) Chain (0) PIFA 2.8 NA 2400-2500 Chain (1) PIFA 2.8 NA 2400-2500 Report No.: SA121204E06 R1 6 of 6 Report Format Version 5.0.0 Cancels and replaces the report No.: SA121204E06 dated Jan. 17, 2013 6. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER FREQUENCY BAND (MHz) MAX POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 586.621 2.80 20 0.22238 1 --- END --- CONCLUSION: Both of the 2.4GHz and 5GHz WLAN can transmit simultaneously, the formula of calculated the MPE is: CPD 1 / LPD 1 + CPD 2 / LPD 2 + ......etc. < 1 CPD = Calculation power density LPD = Limit of power density Therefore, the worst-case situation is 0.19107 / 1 + 0.26777 / 1 = 0.45884, which is less than “1”. This confirmed that the device comply with FCC 1.1310 MPE limit.

Report No.: RF121204E06 R1 1 of 54 Report Format Version 5.1.0 Cancels and replaces the report No.: RF121204E06 dated Jan. 17, 2013 FCC TEST REPORT REPORT NO.: RF121204E06 R1 MODEL NO.: RE1000 VERSION : 2 FCC ID: Q87-RE1000V2 RECEIVED: Dec. 04, 2012 TESTED: Dec. 06 to 20, 2012 ISSUED: Feb. 26, 2013 APPLICANT: Cisco Consumer Products LLC ADDRESS: 121 Theory Drive Irvine, CA 92617(USA) ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF121204E06 R1 2 of 54 Report Format Version 5.1.0 Cancels and replaces the report No.: RF121204E06 dated Jan. 17, 2013 Table of Contents RELEASE CONTROL RECORD ........................................................................................ 4 1. CERTIFICATION .................................................................................................... 5 2. SUMMARY OF TEST RESULTS ............................................................................ 6 2.1 MEASUREMENT UNCERTAINTY .......................................................................... 7 3. GENERAL INFORMATION ..................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT ....................................................................... 8 3.2 DESCRIPTION OF TEST MODES ....................................................................... 10 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........................ 11 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ....................................... 14 3.4 DESCRIPTION OF SUPPORT UNITS .................................................................. 15 3.5 CONFIGURATION OF SYSTEM UNDER TEST ................................................... 15 4. TEST TYPES AND RESULTS .............................................................................. 16 4.1 CONDUCTED EMISSION MEASUREMENT ........................................................ 16 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ...................................... 16 4.1.2 TEST INSTRUMENTS .......................................................................................... 16 4.1.3 TEST PROCEDURES .......................................................................................... 17 4.1.4 DEVIATION FROM TEST STANDARD ................................................................. 17 4.1.5 TEST SETUP ....................................................................................................... 18 4.1.6 EUT OPERATING CONDITIONS ......................................................................... 18 4.1.7 TEST RESULTS ................................................................................................... 19 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................ 21 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............. 21 4.2.2 TEST INSTRUMENTS .......................................................................................... 22 4.2.3 TEST PROCEDURES .......................................................................................... 23 4.2.4 DEVIATION FROM TEST STANDARD ................................................................. 23 4.2.5 TEST SETUP ....................................................................................................... 24 4.2.6 EUT OPERATING CONDITIONS ......................................................................... 24 4.2.7 TEST RESULTS ................................................................................................... 25 4.3 6dB BANDWIDTH MEASUREMENT .................................................................... 38 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT .................................................. 38 4.3.2 TEST INSTRUMENTS .......................................................................................... 38 4.3.3 TEST PROCEDURE ............................................................................................. 38 4.3.4 DEVIATION FROM TEST STANDARD ................................................................. 38 4.3.5 TEST SETUP ...............................................................................…

Text truncated - open the document above for the full version.

Report No.: 120927E07 1 of 3 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: 120927E07 2 of 3 RADIATED EMISSION TEST (Z-plane) Report No.: 120927E07 3 of 3 RADIATED EMISSION TEST (Y-plane)