Q87-WAP54GPEWireless-G Exterior Access Point with Power Over E

A Division of Cisco Systems, Inc. ® Model No. Exterior Access Point Wireless- G WAP54GPE User Guide WIRELESS GHz 2.4 802.11g Wireless-G Exterior Access PointCopyright and TrademarksSpecifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2004 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.How to Use this User GuideThe user guide to the Wireless-G Exterior Access Point has been designed to make understanding networking with the Access Point easier than ever. Look for the following items when reading this User Guide:In addition to these symbols, there are definitions for technical terms that are presented like this:Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like this:Figure numbers and descriptions can also be found in the “List of Figures” section. This exclamation point means there is a caution or warning and is something that could damage your property or the Access Point. word: definition. This checkmark means there is a note of interest and is something you should pay special attention to while using the Access Point. This question mark provides you with a reminder about something you might need to do while using the Access Point. Figure 0-1: Sample Figure Description WAP54GPE-UG-41217NC JL WARNING: This product contains chemicals, including lead, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. Wireless-G Exterior Access PointTable of ContentsChapter 1: Introduction 1 Welcome 1 What’s in this User Guide? 2 Chapter 2: Planning Your Wireless Network 4 Network Topology 4 Roaming 4 Network Layout 4 Chapter 3: Getting to Know the Wireless-G Exterior Access Point 5 The LEDs 5 The Ports 6 The Reset Button and Ground 7 Chapter 4: Connecting the Wireless-G Exterior Access Point 8 Overview 8 Hardware Installation 8 Chapter 5: Setting Up the Wireless-G Exterior Access Point 10 Setup Wizard 10 Chapter 6: Configuring the Wireless-G Exterior Access Point 17 Overview 17 Navigating the Utility 17 Accessing the Utility 19 The Setup Tab 19 The Wireless - Basic Wireless Settings Tab 21 The Wireless - Wireless Security Tab 22 The Wireless - Wireless Network Access Tab 25 The Wireless - Advanced Wireless Settings Tab 25 The AP Mode Tab 27 The Administration - Management Tab 30 The Administration - Log Tab 31 The Administration - Factory Default Tab 33 The Administration - Firmware Upgrade Tab 33 The Administration - Language Upgrade Tab 34 The Administration - Reboot Tab 34 Wireless-G Exterior Access Point The Administration - Config Management Tab 35 The Status - Local Network Tab 35 The Status - Wireless Tab 36 The Status - System Performance Tab 37 Appendix A: Troubleshooting 39 Frequently Asked Questions 39 Appendix B: Wireless Security 43 Security Precautions 43 Security Threats Facing Wireless Networks 43 Appendix C: Upgrading Firmware 46 Appendix D: Windows Help 47 Appendix E: Glossary 48 Appendix F: Specifications 55 Appendix G: Warranty Information 57 Appendix H: Regulatory Information 58 Appendix I: Contact Information 60 Wireless-G Exterior Access Point List of FiguresFigure 3-1: Front Panel 5 Figure 3-2: Ethernet Network Port 6 Figure 3-3: Antenna Port 6 Figure 3-4: Reset Button 7 Figure 4-1: Mark the Locations of the Two Wall-Mount Slots 8 Figure 4-2: Attach the Mounting Plate 8 Figure 4-3: Ground the Access Point 9 Figure 4-4: Attach the Access Point to the Wall 9 Figure 5-1: Setup Wizard’s Welcome Screen 10 Figure 5-2: Connecting the Access Point 11 Figure 5-3: Select an Access Point 11 Figure 5-4: Login Screen 12 Figure 5-5: Configure Network Address Settings Screen 12 Figure 5-6: Wireless Settings Screen 13 Figure 5-7: Wireless Security Settings - WEP Screen 14 Figure 5-8: Wireless Security Settings - WPA-Personal Screen 15 Figure 5-9: Wireless Power Management Screen 15 Figure 5-10: Confirmation Screen 16 Figure 5-11: Congratulations Screen 16 Figure 6-1: Login Screen 19 Figure 6-2: Setup - Automatic Configuration - DHCP Screen 19 Figure 6-3: Setup - Static IP Address Screen 20 Figure 6-4: Wireless - Basic Wireless Settings Screen 21 Figure 6-5: Wireless - Wireless Security (WPA Pre-Shared Key) Screen 22 Figure 6-6: Wireless Security - WPA RADIUS Screen 23 Figure 6-7: Wireless Security - RADIUS Screen 24 Figure 6-8: Wireless Settings - WEP Screen 24 Figure 6-9: Wireless - Wireless Network Access Screen 25 Wireless-G Exterior Access PointFigure 6-10: Wireless - Advanced Wireless Settings Screen 25 Figure 6-11: AP Mode Screen 27 Figure 6-12: Wireless Repeater Diagram 28 Figure 6-13: Site Survey Screen 28 Figure 6-14: Wireless Bridge Diagram 29 Figure 6-15: Administration - Management Screen 30 Figure 6-16: The Administration - Log Screen 31 Figure 6-17: Administration - Factory Default Screen 33 Figure 6-18: Administration - Firmware Upgrade Screen 33 Figure 6-19: Administration - Language Upgrade Screen 34 Figure 6-20: Administration - Reboot Screen 34 Figure 6-21: Administration - Config Management Screen 35 Figure 6-22: Status - Local Network Screen 35 Figure 6-23: Status - Wireless Screen 36 Figure 6-24: Status - System Performance Screen 37 Figure C-1: Firmware Upgrade 46 1 Chapter 1: IntroductionWelcomeWireless-G Exterior Access PointChapter 1: IntroductionWelcomeThank you for choosing the Wireless-G Exterior Access Point. This Access Point will allow you to network wirelessly better than ever.How does the Access Point do all of this? An access point allows for greater range and mobility within your wireless network while also allowing you to connect the wireless network to a wired environment. In fact, the Wireless-G Exterior Access Point can support communications on up to eight wireless networks, using Virtual Local…

Text truncated - open the document above for the full version.

Cisco-Linksys, LLC 121 Theory Drive Irvine, CA 92612 (USA) Phone: 949-823-3188 Fax: 949-823-3002 Date: Dec 20, 2004 FCC ID: Q87-WAP54GPE Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, __________________________________________ Jennifer Yu / Associate Engineer Cisco-Linksys, LLC Tel.: ( 949 ) 823-3188 Fax: ( 949 ) 823-3002 [email protected]

Cisco-Linksys, LLC 121 Theory Drive Irvine, CA 92612 (USA) Phone: 949-823-3188 Fax: 949-823-3002 Date: Dec 20, 2004 FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY (DoC) Cisco-Linksys, LLC declares that the equipment described in this document is within the requirements of the Code of Federal Regulations listed below: Product Name: Wireless-G Exterior Access Point with Power Over Ethernet Model Number: WAP54GPE This device complies with the limits for a Class B digital device pursuant to IEEE ANSI C63.4 and FCC Part 15 subpart B of the Rules and Regulations. The test result has been shown in the ADT test report with numbered FD931102L03 Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. The Part 15 radio device operates on a non-interference basis with other devices operation at this frequency. Any change or modification to the product not expressly approved by Linksys could void the user’s authority to operate the device. Jennifer Yu / Associate Engineer Cisco-Linksys, LLC Tel.: ( 949 ) 823-3188 Fax: ( 949 ) 823-3002 [email protected]

Cisco-Linksys, LLC 121 Theory Drive Irvine, CA 92612 (USA) Phone: 949-823-3188 Fax: 949-823-3002 Agency Authorization Letter Date: Dec 20, 2004 To whom it may concern: We, the undersigned, hereby authorize Advance Data Technology Corp. (ADT) of Taiwan to act on our behalf, as our agent, in the following matters related to the FCC approval of our products: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out by ADT within the scope of this authorization shall have the same effects as our own. This authorization shall expire six months from the original date. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, __________________________________________ Jennifer Yu / Associate Engineer Cisco-Linksys, LLC Tel.: ( 949 ) 823-3188 Fax: ( 949 ) 823-3002 [email protected]

Cisco-Linksys LLC 121 Theory Drive Irvine, CA 92617 (USA) Phone: 949-261-1288 Fax: 949-823-3002 Professional Installation Attestation Date: 03.21.2005 CKC Certification Service 4933 Sierra Pines Drive Mariposa, CA 95338 To Whom It May Concern: Please be advised that due to the unique function supplied by this product, this device is intended for use as a Wireless LAN bridge only and will be distributed through controlled distribution channel which has trained professional to install this product and will not be sold directly to the general public through retail store. Thank you for your attention. Yours sincerely, __________________________________________ Jennifer Yu / Associate Engineer Cisco-Linksys LLC Tel.: ( 949 ) 823-3188 Fax: ( 949 ) 823-3002 [email protected]

-----Original Message----- From: [email protected] [mailto:[email protected]] Sent: Monday, March 21, 2005 7:12 PM To: steve.cheng Cc: [email protected] Subject: 回信: RE: 轉寄： 回信: RE: Solve the pending projects *(FCC ID: Q87-WAP54GPE& IC ID: 3839A-WAP54GPE), 931102L03 Dear Steve Regarding the pending FCC project, I uploaded the Professional Installation Attestation letter and add the Professional installation instruction of the manual on ftp server. For the Canada project, I uploaded the correct test report and manual today. Please check! Thanks for your patience! Best Regards Wendy Liao Wendy Liao (廖意紋)/ ADT Corp. TEL: 03-318-3232 EXT 1625 FAX: 03-318-5050 Email: [email protected] 地址:桃園縣龜山鄉文化村華亞二路１９號 -----Original Message----- From: [email protected] [mailto:[email protected]] Sent: Thursday, March 10, 2005 12:24 AM To: Steve Cheng Cc: [email protected] Subject: 轉寄： 回信: Solve the comment for Q87-WAP54GPE_Cisco Wireless G Exterior AP with Power Over Ethernet Dear Steve We added the external antenna test data in the test report and reply the comment you sent. (FCC Project) Question #1: As indicated on the external photos that there is an external antenna connector furnished with this unit, please clarify the purpose of this external antenna port? And if it is of unique type? Per 15.203, this connect has to be a unique coupling device to compliance with this rule part. Answer: This is a professional installed product. We will revise test report and users manual to address this. Question #2: Schematic does not include RF circuits, please supply. Answer: we re-uploaded the shematic include RF circuits. Question #3: Bandedge measurement has only average plots but no peak measured. Please supply? Answer: The test report added the peak measured for Bandedge measurement. Thanks for your assistance! Best Regards Wendy Liao Wendy Liao (廖意紋)/ ADT Corp. TEL: 03-318-3232 EXT 1625 FAX: 03-318-5050 Email: [email protected] 地址:桃園縣龜山鄉文化村華亞二路１９號 "Steve Cheng" <stevesjcheng@hot mail.com> 收件 人 "Wendy Liao" <[email protected]> 2005/02/24 下午 副本抄 送 01:02 <[email protected]>, <[email protected]> 主旨 Q87-WAP54GPE_Cisco Wireless G Exterior AP with Power Over Ethernet TCB Review Questions for Cisco Wireless G Exterior AP with Power Over Ethernet Q87-WAP54GPE -EMC- Question #1: As indicated on the external photos that there is an external antenna connector furnished with this unit, please clarify the purpose of this external antenna port? And if it is of unique type? Per 15.203, this connect has to be a unique coupling device to compliance with this rule part. Question #2: Schematic does not include RF circuits, please supply. Question #3: Bandedge measurement has only average plots but no peak measured. Please supply? The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 60 days of the original e-mail date may result in application dismissal and forfeiture of the filing fee. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the e-mail address listed below the name of the sender. Best regards, Steve Cheng North American EMC Certification Services Inc. 359 Hawkland Cir., NW. Calgary, Alberta Canada T3G 3R3 Tel: (403) 241-8826 Email: [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

FCC ID Label Location

Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14

FCC ID: Q87-WAP54GPE Report No. RF931102L03 Operational Description This device is a Wireless-G Exterior Access Point with Power Over Ethernet which operates in the 2.4GHz frequency spectrum with throughput of up to 54Mbps which OFDM technique will be applied. If the signal to noise radio is too poor which could not support 54Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by POE. The antenna are Patch antenna with UFL connector and Omnidirectional Antenna with N-Type connector. Under normal use condition, the user has to keep at least 20cm separation distance between radiator and the body of the user. The other instruction, please have a look at the users manual.

FCC ID: Q87-WAP54GPE Report No: SA931102L03 1 RF EXPOSURE REPORT REPORT NO.: SA931102L03 MODEL NO.: WAP54GPE ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT: Cisco-Linksys, LLC ADDRESS: 121 Theory Drive Irvine, CA 92617, U.S.A. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. FCC ID: Q87-WAP54GPE Report No: SA931102L03 2 RF Exposure Measurement (Mobile Device) 1. Introduction In this document, we try to prove the safety of radiation harmfulness to the human body for our product. The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The Gain of the antenna used in this product is measured in a Fully Anechoic Chamber (FAC) calibrated for antenna measurement in ADT, and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis transmission formula is a far field assumption, the calculated result of that is an over-prediction for near field power density. We will take that as the worst case to specify the safety range. 2. RF Exposure Limit According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) (A)Limits For Occupational / Control Exposures 300-1500......F/3006 1500-100,000......56 (B)Limits For General Population / Uncontrolled Exposure 300-1500......F/15006 1500-100,000......1.030 F = Frequency in MHz FCC ID: Q87-WAP54GPE Report No: SA931102L03 3 3. Friis Formula Friis transmission formula : Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm If we know the maximum Gain of the antenna and the total power input to the antenna, through the calculation, we will know the MPE value at distance r. Ref. : David K. Cheng, Field and Wave Electromagnetics, Second Edition, Page 640, Eq. (11-133). 4 EUT Operating condition The software provided by Manufacturer enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. 5. Classification The antenna of the product, under normal use condition, is at least 20cm away from the body of the user. Warming statement for keeping 20cm separation distance and the prohibition of operating next to a person has been printed on the user’s manual. So, this product is classified as the Mobile Device. FCC ID: Q87-WAP54GPE Report No: SA931102L03 4 6 Test Results 6.1 Antenna Gain The maximum Gain measured in Fully Anechoic Chamber is 9dBi or 7.94 (numeric). 6.2 Output Power Into Antenna & RF Exposure value at distance 20cm: DSSS Mode: Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1241226.0620.0411.0 6243726.3630.0421.0 1124625.2970.0081.0 OFDM Mode: Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1241225.3510.0401.0 6243725.4680.0401.0 1124624.1880.0071.0

FCC ID: Q87-WAP54GPE Report No.: RF931102L031 Report Format Version 2.0.2 FCC TEST REPORT REPORT NO.: RF931102L03 MODEL NO.: WAP54GPE RECEIVED: Nov. 08 2004 TESTED: Nov. 08 ~ Feb. 25, 2005 ISSUED: Mar. 04, 2005 APPLICANT: Cisco-Linksys LLC ADDRESS: 121 Theory Drive Irvine, CA 92617, U.S.A. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 71 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA No. 2177-01 FCC ID: Q87-WAP54GPE Report No.: RF931102L032Report Format Version 2.0.2 Table of Contents 1 CERTIFICATION ............................................................................................................4 2 SUMMARY OF TEST RESULTS....................................................................................5 2.1 MEASUREMENT UNCERTAINTY ................................................................................5 3 GENERAL INFORMATION ............................................................................................6 3.1 GENERAL DESCRIPTION OF EUT ..............................................................................6 3.2 DESCRIPTION OF TEST MODES ................................................................................7 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST............................................................7 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ...............................8 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS .............................................10 3.4 DESCRIPTION OF SUPPORT UNITS ........................................................................10 4 TEST TYPES AND RESULTS ..................................................................................... 11 4.1 CONDUCTED EMISSION MEASUREMENT ..............................................................11 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT........................................... 11 4.1.2 TEST INSTRUMENTS................................................................................................ 11 4.1.3 TEST PROCEDURES ................................................................................................12 4.1.4 DEVIATION FROM TEST STANDARD.......................................................................12 4.1.5 TEST SETUP..............................................................................................................13 4.1.6 EUT OPERATING CONDITIONS ...............................................................................13 4.1.7 TEST RESULTS .........................................................................................................14 4.2RADIATED EMISSION MEASUREMENT ..................................................................20 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT................................................20 4.2.2 TEST INSTRUMENTS................................................................................................21 4.2.3 TEST PROCEDURES ................................................................................................22 4.2.4 DEVIATION FROM TEST STANDARD ......................................................................22 4.2.5 TEST SETUP .............................................................................................................23 4.2.6 EUT OPERATING CONDITIONS ...............................................................................23 4.2.7 TEST RESULTS .........................................................................................................24 4.36dB BANDWIDTH MEASUREMENT .........................................................................38 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT .......................................................38 4.3.2 TEST INSTRUMENTS................................................................................................38 4.3.3 TEST PROCEDURE...................................................................................................39 4.3.4 DEVIATION FROM TEST STANDARD ......................................................................39 4.3.5 TEST SETUP .............................................................................................................39 4.3.6 EUT OPERATING CONDITIONS ...............................................................................39 4.3.7 TEST RESULTS .........................................................................................................40 4.4MAXIMUM PEAK OUTPUT POWER .........................................................................46 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT..........................46 4.4.2 TEST INSTRUMENTS................................................................................................46 4.4.3 TEST PROCEDURES ................................................................................................47 4.4.4 DEVIATION FROM TEST STANDARD ......................................................................47 4.4.5 TEST SETUP .............................................................................................................47 4.4.6 EUT OPERATING CONDITIONS ...............................................................................47 4.4.7 TEST RESULTS .........................................................................................................48 4.5POWER SPECTRAL DENSITY MEASUREMENT ....................................................49 FCC ID: …

Text truncated - open the document above for the full version.

FCC ID: Q87-WAP54GPE Report No.: RF931102L0368Report Format Version 2.0.2 5 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST FCC ID: Q87-WAP54GPE Report No.: RF931102L0369Report Format Version 2.0.2 RADIATED EMISSION TEST (Patch Antenna) FCC ID: Q87-WAP54GPE Report No.: RF931102L0370Report Format Version 2.0.2 (Omnidirectional Antenna)