Q87-WES610NV24-Port-Dual-Band N Entertainment

User Guide Linksys WET610N/WES610NDual-Band N Entertainment Bridge i Contents Linksys E-Series i Product Overview LED panel 2 Ports panel 3 Wireless Security Checklist Change the default wireless network name or SSID 4 Change the default password 4 Enable MAC address filtering 4 Enable encryption 4 General Network Security Guidelines 4 Additional Security Tips 5 Advanced Configuration How to access the browser-based utility 6 Setup > Basic Setup 7 Language 7 Network Setup 7 Wireless > Basic Wireless Settings 7 Basic Wireless Settings 8 Wireless Security 8 Wi-Fi Protected Setup 9 Wireless > Wireless Network Site Survey 10 Wireless Network Site Survey 10 Wireless > WMM® 11 WMM 12 Wireless > Advanced Wireless Settings 13 Advanced Wireless 13 Administration > Management 14 Management 14 Administration > Factory Defaults 15 Factory Defaults 15 Administration > Upgrade Firmware 15 Upgrade Firmware 15 Status > Bridge 15 Bridge Information 16 Local Network 16 Status > Wireless 16 Wireless 16 Troubleshooting WES610N/WET610N 17 Specifications WES610N 18 WET610N 19 Contents 2 Product Overview Linksys WES610N/WET610N 2 Thank you for choosing the Linksys Dual-Band N Entertainment Bridge The bridge can connect any wired, Ethernet device to your wireless network The bridge is based on dual-band Wireless-N, so it is compatible with any Wireless-N, -G, -A, or -B router or access point For first-time installation, follow the steps on the CD folder To configure advanced settings, use the convenient, browser-based utility LED panel WES610NWET610N Wireless (Blue) The Wireless LED lights up when there is a wireless connection The LED flashes when the bridge is actively sending or receiving data over the wireless network Wi-Fi Protected Setup Button If your router supports Wi-Fi Protected Setup and uses WPA or WPA2 security, then you can use Wi-Fi Protected Setup to automatically connect the bridge To use Wi-Fi Protected Setup, refer to “Wireless > Basic Wireless Settings” on page 7 Wi-Fi Protected Setup LED (Blue/Amber) The LED flashes blue for two minutes during Wi-Fi Protected Setup It lights up blue when wireless security is enabled If there is an error during the Wi-Fi Protected Setup process, then the LED lights up amber Make sure the network router supports Wi-Fi Protected Setup Wait until the LED is off, and then try again Ethernet (Blue) The Ethernet LED lights up when there is a wired connection The LED flashes when the bridge is actively sending or receiving data over the Ethernet port(s) Power (Blue) The Power LED lights up when the bridge is powered on Product Overview 3 Product Overview Linksys WES610N/WET610N Ports panel WES610NWET610N Ethernet The Ethernet port(s) connects the bridge to a computer or other Ethernet network device The WES610N has four ports, and the WET610N has a single port Reset There are two ways to reset the bridge’s factory defaults Either press and hold the Reset button for approximately five seconds, or restore the defaults from Administration > Factory Defaults in the bridge’s browser-based utility The WES610N has a reset button on the bottom, and the WET610N has a reset button on the back port panel Power The Power port connects the bridge to the included power adapter 4 Wireless Security Checklist Linksys WES610N/WET610N 4 Wireless networks are convenient and easy to install, so homes with high- speed Internet access are adopting them at a rapid pace Because wireless networking operates by sending information over radio waves, it can be more vulnerable to intruders than a traditional wired network Like signals from your cellular or cordless phones, signals from your wireless network can also be intercepted Since you cannot physically prevent someone from connecting to your wireless network, you need to take some additional steps to keep your network secure Change the default wireless network name or SSID Wireless devices have a default wireless network name or Service Set Identifier (SSID) set by the factory This is the name of your wireless network, and can be up to 32 characters in length Linksys wireless products use linksys as the default wireless network name You should change the wireless network name to something unique to distinguish your wireless network from other wireless networks that may exist around you, but do not use personal information (such as your Social Security number) because this information may be available for anyone to see when browsing for wireless networks Change the default password For wireless products such as access points and routers, you will be asked for a password when you want to change their settings These devices have a default password set by the factory The Linksys default password is admin Hackers know these defaults and may try to use them to access your wireless device and change your network settings To thwart any unauthorized changes, customize the device’s password so it will be hard to guess Enable MAC address filtering Linksys routers give you the ability to enable Media Access Control (MAC) address filtering The MAC address is a unique series of numbers and letters assigned to every networking device With MAC address filtering enabled, wireless network access is provided solely for wireless devices with specific MAC addresses For example, you can specify the MAC address of each computer in your home so that only those computers can access your wireless network Enable encryption Encryption protects data transmitted over a wireless network Wi-Fi Protected Access (WPA/WPA2) and Wired Equivalent Privacy (WEP) offer different levels of security for wireless communication A network encrypted with WPA/WPA2 is more secure than a network encrypted with WEP, because WPA/WPA2 uses dynamic key encryption To protect the information as it passes over the airwaves, you should enable the highest level of encryption supported by your network equipment WEP is an older encryption standard and may be the only option available on some olde…

Text truncated - open the document above for the full version.

Linksys Dual-Band Routers and Bridges Regulatory Information Table of Contents i Linksys Regulatory Information Table of Contents Wireless Regulatory Information 1 FCC Statement 1 Mexico Regulatory Statement 1 FCC Radiation Exposure Statement 1 Safety Notices 1 Industry Canada Statement 1 Restrictions in the 5 GHz Band 1 Avis d’Industrie Canada 2 Restrictions dans la bande 5 GHz 2 Wireless Disclaimer 2 Avis de non-responsabilité concernant les appareils sans fil 2 Declaration of Conformity with Regard to EU Directive 1999/5/EC (R&TTE Directive) 2 Wireless Equipment (Wireless-AC/N/G/A/B Products) 3 National Restrictions 3 Product Usage Restrictions 4 Technical Documents on www myciscohome com 4 WEEE Information 5 User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE) 5 1 Linksys Regulatory InformationWireless Regulatory Information Wireless Regulatory Information FCC Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna •Increase the separation between the equipment or devices •Connect the equipment to an outlet other than the receiver’s •Consult a dealer or an experienced radio/TV technician for assistance FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment IEEE 802 11b or 802 11g operation of this product in the USA is firmware-limited to channels 1 through 11 The device for the band 5150-5250 MHz is only for indoor usage to reduce the potential for harmful interference to co-channel mobile satellite systems Mexico Regulatory Statement La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter Safety Notices WARNING: Do not use this product near water, for example, in a wet basement or near a swimming pool WARNING: Avoid using this product during an electrical storm There may be a remote risk of electric shock from lightning WARNING: This product contains lead, known to the State of California to cause cancer, and birth defects or other reproductive harm Wash hands after handling Industry Canada Statement This Class B digital apparatus complies with Canadian ICES-003 and RSS210 Operation is subject to the following two conditions: 1 This device may not cause interference and 2 This device must accept any interference, including interference that may cause undesired operation of the device Industry Canada Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter Restrictions in the 5 GHz Band The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co- channel mobile satellite systems Because high power radars are allocated as primary users (meaning they have priority) in 5250-5350 MHz and 5650-5850 MHz, these radars could cause interference and/or damage to licensed exempt LAN devices Additional requirements for the band 5600-5650 MHz: Until further notice, devices subject to this Section shall not be capable of transmitting in the band 5600- 5650 MHz, so that Environment Canada weather radars operating in this band are protected 2 Linksys Regulatory InformationWireless Regulatory Information Avis d’Industrie Canada Cet appareil numérique de la classe B est conforme aux normes NMB-003 et RSS210 du Canada L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : 1 il ne doit pas produire de brouillage et 2 il doit accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif Avis d’Industrie Canada concernant l’exposition aux radiofréquences Ce matériel est conforme aux limites établies par IC en matière d’exposition aux radiofréquences dans un environnement non contrôlé Ce matériel doit être installé et utilisé à une distance d’au moins 20 cm entre l’antenne et le corps de l’utilisateur L’émetteur ne doit pas être placé près d’une autre antenne ou d’un autre émetteur, ou fonctionner avec une autre antenne ou un autre émetteur Restrictions dans la bande 5 GHz L’appareil pour la bande de 5150 à 5250 MHz …

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT Page 4 Page 12 Page 13 Page 14

V2V2 WES610N V2 Product Label for Certificaiton NOV 28, 2012 U-MEDIA V2

(Fig.1) FCC ID: Q87-WES610NV2 FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Bottom:

Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11

Report No.: SA121105E01 1 of 5 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA121105E01 MODEL NO.: WES610N V2 FCC ID: Q87-WES610NV2 RECEIVED: Nov. 05, 2012 TESTED: Nov. 13 ~ Dec. 07, 2012 ISSUED: Dec. 13, 2012 APPLICANT: Cisco Consumer Products LLC ADDRESS: 121 Theory Drive Irvine, CA 92617(USA) ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. Report No.: SA121105E01 2 of 5 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................ 3 1. CERTIFICATION ............................................................................................................ 4 2. RF EXPOSURE .............................................................................................................. 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) ........................................ 5 2.2 MPE CALCULATION FORMULA ................................................................................... 5 2.3 CLASSIFICATION .......................................................................................................... 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ................................. 5 Report No.: SA121105E01 3 of 5 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA121105E01 Original release Dec. 13, 2012 Report No.: SA121105E01 4 of 5 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT: 4-Port Dual-Band N Entertainment Bridge MODEL NO.: WES610N V2 BRAND: Cisco APPLICANT: Cisco Consumer Products LLC TESTED: Nov. 13 ~ Dec. 07, 2012 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model: WES610N V2) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :Dec. 13, 2012 Jemma Yang / Specialist APPROVED BY : , DATE :Dec. 13, 2012 Ken Liu / Manager Report No.: SA121105E01 5 of 5 Report Format Version 5.0.0 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. 2.4 Calculation result of maximum conducted power FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412~2462 25.41 3.5 20 0.1548 1 5180~5240 14.96 5 20 0.0197 1 5260~5320 15.11 5 20 0.0204 1 5500~5700 15.37 5 20 0.0217 1 5745~5825 22.75 5 20 0.1185 1

Report No.: RF121105E01 1 of 85 Report Format Version 5.1.0 FCC TEST REPORT (15.247) REPORT NO.: RF121105E01 MODEL NO.: WES610N V2 FCC ID: Q87-WES610NV2 RECEIVED: Nov. 05, 2012 TESTED: Nov. 13 ~ Dec. 07, 2012 ISSUED: Dec. 13, 2012 APPLICANT: Cisco Consumer Products LLC ADDRESS: 121 Theory Drive Irvine, CA 92617(USA) ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF121105E01 2 of 85 Report Format Version 5.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................................ 5 1. CERTIFICATION ......................................................................................................................... 6 2. SUMMARY OF TEST RESULTS ................................................................................................ 7 2.1 MEASUREMENT UNCERTAINTY .............................................................................................. 7 3. GENERAL INFORMATION ......................................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT ........................................................................................... 8 3.2 DESCRIPTION OF TEST MODES ........................................................................................... 10 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........................................... 11 3.3 DESCRIPTION OF SUPPORT UNITS ..................................................................................... 16 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ...................................................................... 17 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS .......................................................... 18 4. TEST TYPES AND RESULTS (FOR 2.4GHz BAND) ............................................................... 19 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................................. 19 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................ 19 4.1.2 TEST INSTRUMENTS .............................................................................................................. 20 4.1.3 TEST PROCEDURES .............................................................................................................. 21 4.1.4 DEVIATION FROM TEST STANDARD .................................................................................... 21 4.1.5 TEST SETUP ............................................................................................................................ 22 4.1.6 EUT OPERATING CONDITIONS ............................................................................................. 22 4.1.7 TEST RESULTS ....................................................................................................................... 23 4.2 CONDUCTED EMISSION MEASUREMENT ........................................................................... 36 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................................ 36 4.2.2 TEST INSTRUMENTS .............................................................................................................. 36 4.2.3 TEST PROCEDURES .............................................................................................................. 37 4.2.4 DEVIATION FROM TEST STANDARD .................................................................................... 37 4.2.5 TEST SETUP ............................................................................................................................ 38 4.2.6 EUT OPERATING CONDITIONS ............................................................................................. 38 4.2.7 TEST RESULTS ....................................................................................................................... 39 4.3 6dB BANDWIDTH MEASUREMENT ........................................................................................ 43 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ..................................................................... 43 4.3.2 TEST SETUP ............................................................................................................................ 43 4.3.3 TEST INSTRUMENTS ..........…

Text truncated - open the document above for the full version.

Report No.: RF121105E01-1 1 of 77 Report Format Version 5.1.0 FCC TEST REPORT (15.407) REPORT NO.: RF121105E01-1 MODEL NO.: WES610N V2 FCC ID: Q87-WES610NV2 RECEIVED: Nov. 05, 2012 TESTED: Nov. 13 ~ Dec. 07, 2012 ISSUED: Dec. 13, 2012 APPLICANT: Cisco Consumer Products LLC ADDRESS: 121 Theory Drive Irvine, CA 92617(USA) ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF121105E01-1 2 of 77 Report Format Version 5.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................................ 4 1. CERTIFICATION ......................................................................................................................... 5 2. SUMMARY OF TEST RESULTS ................................................................................................ 6 2.1 MEASUREMENT UNCERTAINTY .............................................................................................. 6 3. GENERAL INFORMATION ......................................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ........................................................................................... 7 3.2 DESCRIPTION OF TEST MODES ............................................................................................. 9 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........................................... 10 3.3 DUTY CYCLE OF TEST SIGNAL ............................................................................................. 12 3.4 DESCRIPTION OF SUPPORT UNITS ..................................................................................... 13 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST ...................................................................... 14 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS .......................................................... 15 4. TEST TYPES AND RESULTS .................................................................................................. 16 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................................. 16 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................ 16 4.1.2 LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS ........................... 16 4.1.3 TEST INSTRUMENTS .............................................................................................................. 17 4.1.4 TEST PROCEDURES .............................................................................................................. 18 4.1.5 DEVIATION FROM TEST STANDARD .................................................................................... 18 4.1.6 TEST SETUP ............................................................................................................................ 19 4.1.7 EUT OPERATING CONDITION ................................................................................................ 19 4.1.8 TEST RESULTS ....................................................................................................................... 20 4.2 CONDUCTED EMISSION MEASUREMENT ........................................................................... 45 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................................ 45 4.2.2 TEST INSTRUMENTS .............................................................................................................. 45 4.2.3 TEST PROCEDURES .............................................................................................................. 46 4.2.4 DEVIATION FROM TEST STANDARD .................................................................................... 46 4.2.5 TEST SETUP ............................................................................................................................ 46 4.2.6 EUT OPERATING CONDITIONS ............................................................................................. 46 4.2.7 TEST RESULTS ....................................................................................................................... 47 4.3 PEAK TRANSMIT POWER MEASUREMENT ......................................................................... 55 4.3.1 LIMITS OF PEAK TRANSMIT POWER MEASUREMENT ........…

Text truncated - open the document above for the full version.

Report No.: RF121105E01-2 1 of 23 Report Format Version 5.0.0 DFS TEST REPORT REPORT NO.: RF121105E01-2 MODEL NO.: WES610N V2 FCC ID: Q87-WES610NV2 RECEIVED: Nov. 05, 2012 TESTED: Nov. 13 ~ Dec. 07, 2012 ISSUED: Dec. 13, 2012 APPLICANT: Cisco Consumer Products LLC ADDRESS: 121 Theory Drive Irvine, CA 92617(USA) ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C. ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only …

Text truncated - open the document above for the full version.