Q87-WUSBF54GWireless-G USB Adapter with Wi-Fi Finder

A Division of Cisco Systems, Inc. ® Model No. USB Network Adapter Wireless-G WUSBF54G User Guide WIRELESS GHz 2.4 802.11g with Wi-Fi Finder Wireless-G USB Network Adapter with Wi-Fi Finder Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2005 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders. How to Use this User Guide This User Guide has been designed to make understanding networking with the Wireless-G USB Network Adapter with Wi-Fi Finder easier than ever. Look for the following items when reading this User Guide: In addition to these symbols, there are definitions for technical terms that are presented like this: Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like this: Figure numbers and descriptions can also be found in the "List of Figures" section in the “Table of Contents”. This exclamation point means there is a Caution or warning and is something that could damage your property or the Wireless-G USB Network Adapter with Wi-Fi Finder. This checkmark means there is a Note of interest and is something you should pay special attention to while using the Wireless-G USB Network Adapter with Wi-Fi Finder. This question mark provides you with a reminder about something you might need to do while using the Wireless-G USB Network Adapter with Wi-Fi Finder. word: definition. Figure 0-1: Sample Figure Description WUSBF54G-UG-50810NC BW WARNING:This product contains chemicals, including lead, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. Wireless-G USB Network Adapter with Wi-Fi Finder Table of Contents Chapter 1: Introduction1 Welcome1 What’s in this Guide?2 Chapter 2: Planning your Wireless Network4 Network Topology4 Roaming4 Network Layout5 Chapter 3: Getting to Know and Using the Wireless-G Network Adapter with Wi-Fi Finder6 The Front Panel6 Using the Wi-Fi Finder7 The Side Panels8 Chapter 4: Setting up and Connecting the Wireless-G USB Network Adapter with Wi-Fi Finder9 Starting the Setup Wizard9 Connecting the Adapter10 Setting Up the Adapter10 Chapter 5: Using the Wireless Network Monitor20 Accessing the Wireless Network Monitor20 Link Information Screens20 Site Survey23 Profiles24 Creating a New Profile25 Appendix A: Troubleshooting35 Common Problems and Solutions35 Frequently Asked Questions36 Appendix B: Using Windows XP Wireless Configuration39 Appendix C: Wireless Security42 Security Precautions42 Security Threats Facing Wireless Networks42 Appendix D: Windows Help45 Wireless-G USB Network Adapter with Wi-Fi Finder Appendix E: Glossary46 Appendix F: Specifications53 Appendix G: Warranty Information54 Appendix H: Regulatory Information55 Appendix I: Contact Information57 Wireless-G USB Network Adapter with Wi-Fi Finder List of Figures Figure 3-1: Front Panel6 Figure 3-2: Wi-Fi Finder’s Wireless Network Screen7 Figure 3-3: Wi-Fi Finder’s ON/OFF Switch and Buttons8 Figure 4-1: Setup Wizard’s Welcome Screen9 Figure 4-2: Setup Wizard’s License Agreement9 Figure 4-3: The Connecting the Adapter Screen10 Figure 4-4: Available Wireless Network10 Figure 4-5: Available Wireless Network11 Figure 4-6: Wireless Security - WEP11 Figure 4-7: Wireless Security - WPA Personal12 Figure 4-8: Congratulations12 Figure 4-9: Available Wireless Network13 Figure 4-10: Network Settings13 Figure 4-11: Wireless Mode14 Figure 4-12: Ad-Hoc Mode Settings14 Figure 4-13: Wireless Security15 Figure 4-14: Wireless Security - WEP15 Figure 4-15: Wireless Security - WPA Personal16 Figure 4-16: Wireless Security - WPA Enterprise - EAP-TLS17 Figure 4-17: Wireless Security - WPA Enterprise - PEAP17 Figure 4-18: Wireless Security - RADIUS - EAP-TLS18 Figure 4-19: Wireless Security - RADIUS - PEAP18 Figure 4-20: Confirm New Settings19 Figure 4-21: Congratulations19 Figure 5-1: Wireless Network Monitor Icon20 Figure 5-2: Link Information20 Figure 5-3: More Information - Wireless Network Status21 Figure 5-4: More Information - Wireless Network Statistics22 Figure 5-5: Site Survey23 Figure 5-6: WEP Key Needed for Connection23 Wireless-G USB Network Adapter with Wi-Fi Finder Figure 5-7: WPA-Personal Needed for Connection23 Figure 5-8: Profiles24 Figure 5-9: Import a Profile24 Figure 5-10: Export a Profile24 Figure 5-11: Create a New Profile25 Figure 5-12: Available Wireless Network25 Figure 5-13: Available Wireless Network26 Figure 5-14: WEP Key Needed for Connection26 Figure 5-15: WPA-Personal Needed for Connection27 Figure 5-16: The Congratulations Screen27 Figure 5-17: Available Wireless Network28 Figure 5-18: Network Settings28 Figure 5-19: Wireless Mode29 Figure 5-20: Ad-Hoc Mode Settings29 Figure 5-21: Wireless Security30 Figure 5-22: Wireless Security - WEP30 Figure 5-23: Wireless Security - WPA Personal31 Figure 5-24: Wireless Security - WPA Enterprise - EAP-TLS32 Figure 5-25: Wireless Security - WPA Enterprise - PEAP32 Figure 5-26: Wireless Security - RADIUS - EAP-TLS33 Figure 5-27: Wireless Security - RADIUS - PEAP33 Figure 5-28: Confirm New Settings34 Figure 5-29: The Congratulations Screen34 Figure B-1: Wireless Network Monitor Icon39 Figure B-2: Windows XP - Use Windows XP Wireless Configuration39 Figure B-3: Windows XP Wireless Configuration Icon39 Figure B-4: Available Wireless Network40 Figure B-5: No Wireless Security40 Figure B-6: Network Connection - Wireless Security41 Figure B-7: Wireless Network Connection41 1 Chapter 1: Introduction Welcome Wireless-G USB Network Adapter with Wi-Fi Finder Chapter 1: Introduction Welcome Thank you for choosing the Wireless-G USB Network Adapter with Wi-Fi Finder. With this Adapter, your wireless networking experience will be faster and easier than ever. How does the Adapter do …

Text truncated - open the document above for the full version.

32 Chapter 5: Using the Wireless Network Monitor Creating a New Profile Wireless-G USB Network Adapter with Wi-Fi Finder WPA Enterprise WPA Enterprise features WPA security used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) WPA Enterprise offers two authentication methods, EAP- TLS and PEAP, as well as two encryption methods, TKIP and AES, with dynamic encryption keys. Authentication - Select the authentication method your network is using, EAP-TLS or PEAP. EAP-TLS If you selected EAP-TLS, enter the login name of your wireless network in the Login Name field. Enter the name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have installed to authenticate you on your wireless network. Select the type of encryption, TKIP or AES, from the Encryption drop-down menu. Click the Next button to continue or the Back button to return to the previous screen. PEAP If you selected PEAP, enter the login name of your wireless network in the Login Name field. Enter the password of your wireless network in the Password field. Enter the name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have installed to authenticate you on your wireless network; if you want to use any certificate, keep the default setting, Trust Any. Then select the authentication method (Inner Authen.) used inside the PEAP tunnel. Select EAP-MSCHAP v2. Then, select the type of encryption, TKIP or AES, from the Encryption drop-down menu. Click the Next button to continue or the Back button to return to the previous screen. Figure 5-24: Wireless Security - WPA Enterprise - EAP-TLS Figure 5-25: Wireless Security - WPA Enterprise - PEAP 33 Chapter 5: Using the Wireless Network Monitor Creating a New Profile Wireless-G USB Network Adapter with Wi-Fi Finder RADIUS RADIUS uses the security of a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) It offers two authentication methods: EAP-TLS and PEAP. Authentication - Select the authentication method your network is using, EAP-TLS or PEAP. EAP-TLS Enter the Login name of your wireless network in the Login Name field. From the Certificate drop-down menu, select the certificate you have installed to authenticate you on your wireless network. PEAP If you selected PEAP, enter the login name of your wireless network in the Login Name field. Enter the password of your wireless network in the Password field. Enter the name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have installed to authenticate you on your wireless network; if you want to use any certificate, keep the default setting, Trust Any. Then select the authentication method (Inner Authen.) used inside the PEAP tunnel. Select EAP-MSCHAP v2. Click the Next button to continue to the Confirm New Settings screen or the Back button to return to the previous screen. Figure 5-26: Wireless Security - RADIUS - EAP-TLS Figure 5-27: Wireless Security - RADIUS - PEAP 34 Chapter 5: Using the Wireless Network Monitor Creating a New Profile Wireless-G USB Network Adapter with Wi-Fi Finder 5. The next screen displays all of the Adapter’s settings. If these are correct, you can save these settings to your hard drive by clicking Save. Click Next to continue. If these settings are not correct, click Back to change your settings. 6. After the software has been successfully installed, the Congratulations screen will appear. Click Connect to Network to connect to your network. Clicking Return to Profile will open the Wireless Network Monitor’s Profiles screen. Congratulations! The profile has been configured. Figure 5-28: Confirm New Settings Figure 5-29: The Congratulations Screen 35 Appendix A: Troubleshooting Common Problems and Solutions Wireless-G USB Network Adapter with Wi-Fi Finder Appendix A: Troubleshooting This appendix provides solutions to problems usually encountered during the installation and operation of the Adapter. Read the description below to solve your problems. If you can't find an answer here, check the Linksys website at www.linksys.com. Common Problems and Solutions 1.My computer does not recognize the USB Network Adapter. •Make sure that the USB Network Adapter is properly inserted into the USB port. •Also, make sure that the USB Controller is enabled in the BIOS. Check with your motherboard User Guide for more information. 2. The USB Network Adapter does not work properly. •Reinsert the USB Network Adapter into the notebook or desktop’s USB port. •Right-click on My Computer, and select Properties. Select the Adapter, then chose the Device Manager tab, and click on the Network Adapter. You will find the USB Network Adapter if it is installed successfully. If you see a yellow exclamation mark, the resources may be conflicting and you must follow the steps below: •Uninstall the driver software from your PC. •Restart your PC and repeat the hardware and software installation as specified in this User Guide. 3. I cannot communicate with the other computers linked via Ethernet in the Infrastructure configuration. •Make sure that the notebook or desktop is powered on. •Make sure that your USB Network Adapter is configured on the same channel, SSID, and WEP as the other computers in the Infrastructure configuration. 36 Appendix A: Troubleshooting Frequently Asked Questions Wireless-G USB Network Adapter with Wi-Fi Finder Frequently Asked Questions Can I run an application from a remote computer over the wireless network? This will depend on whether or not the application is designed to be used over a network. Consult the application’s user guide to determine if it supports operation over a network. Can I play computer games with other members of the wireless network? Yes,…

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

FCC ID : Q87-WUSBF54G Label Location

WUSBF54G Bottom Label 63.000.15 1 9 . 7 0 0 . 1 5 Q87-WUSBF54G IC: 3839A-WUSBF54G WUSBF54G Wireless-G USB Adapter with Wi-Fi Finder

Page 3 Page 4 Page 5 Page 6 Page 7

FCC ID: Q87-WUSBF54G Report No. RF940826L01 Technical Description This device is a Wireless-G USB Adapter with Wi-Fi Finder which operates in the 2.4GHz frequency spectrum with throughput of up to 54Mbps which OFDM technique will be applied. If the signal to noise radio is too poor which could not support 54Mbps, the 11Mbps data rate with DSSS technique will be applied. This is a multi-functional device features Hotspot Finder and Wireless-G USB Adapter in a compact enclosure. This Finder supports graphical LCD display with readable and complete site survey information, such as Signal Strength, Security and Encryption, Operation Channel, Radio Band and SSID. The transmitter of the EUT is powered by host equipment. The antenna used in this product is Printed antenna without connector. The other instruction, please have a look at the users manual.

D3: DAE SN: 579

APPENDIX D: SYSTEM CERTIFICATE & CALIBRATION D1: SAM PHANTOM

A - 1 APPENDIX A: TEST CONFIGURATIONS AND TEST DATA A1: TEST CONFIGURATION EUT PLACE : Horizontal The bottom of the EUT to the flat phantom distance 7 mm A - 2 EUT PLACE : Vertical The edge of the EUT to the flat phantom distance 6 mm A - 3 EUT Photo Reference Point A - 4 A - 5 Liquid Level Photo MSL 2450MHz D=152mm A - 6 Date/Time: 2005/8/30 15:41:41 Test Laboratory: Advance Data Technology WUSBF54G-Horizontal-N800C-11b-Mode 1 DUT: Wireless-G USB Adapter with Wi-Fi Finder ; Type: WUSBF54G ; Test Frequency: 2412 MHz Communication System: 802.11b ; Frequency: 2412 MHz ; Duty Cycle: 1:1 ; Modulation type: CCK Medium: MSL2450 Medium parameters used: f = 2412 MHz; σ = 1.94 mho/m; ε r = 50.7; ρ = 1000 kg/m 3 ; Liquid level : 152mm Phantom section: Flat Section ; Separation distance : 7 mm (The bottom side of the EUT to the Phantom) Antenna type : Internal Antenna ; Air temp. : 22.1 degrees ; Liquid temp. : 21.6 degrees DASY4 Configuration: - Probe: ET3DV6 - SN1790 ; ConvF(4.35, 4.35, 4.35) ; Calibrated: 2004/12/20 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579 ; Calibrated: 2005/3/23 - Phantom: SAM 12 ; Type: SAM V4.0 ; Serial: TP 1202 - Measurement SW: DASY4, V4.5 Build 19 ; Postprocessing SW: SEMCAD, V1.8 Build 146 Low Channel 1/Area Scan (5x9x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.855 mW/g Low Channel 1/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 17.1 V/m Peak SAR (extrapolated) = 1.93 W/kg SAR(1 g) = 0.779 mW/g; SAR(10 g) = 0.390 mW/g Maximum value of SAR (measured) = 0.849 mW/g A - 7 Date/Time: 2005/8/30 15:58:26 Test Laboratory: Advance Data Technology WUSBF54G-Horizontal-N800C-11b-Mode 1 DUT: Wireless-G USB Adapter with Wi-Fi Finder ; Type: WUSBF54G ; Test Frequency: 2437 MHz Communication System: 802.11b ; Frequency: 2437 MHz ; Duty Cycle: 1:1 ; Modulation type: CCK Medium: MSL2450 Medium parameters used: f = 2437 MHz; σ = 1.98 mho/m; ε r = 50.6; ρ = 1000 kg/m 3 ; Liquid level : 152mm Phantom section: Flat Section ; Separation distance : 7 mm (The bottom side of the EUT to the Phantom) Antenna type : Internal Antenna ; Air temp. : 22.1 degrees ; Liquid temp. : 21.6 degrees DASY4 Configuration: - Probe: ET3DV6 - SN1790 ; ConvF(4.35, 4.35, 4.35) ; Calibrated: 2004/12/20 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579 ; Calibrated: 2005/3/23 - Phantom: SAM 12 ; Type: SAM V4.0 ; Serial: TP 1202 - Measurement SW: DASY4, V4.5 Build 19 ; Postprocessing SW: SEMCAD, V1.8 Build 146 Mid Channel 6/Area Scan (5x9x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.926 mW/g Mid Channel 6/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 17.8 V/m Peak SAR (extrapolated) = 1.97 W/kg SAR(1 g) = 0.869 mW/g; SAR(10 g) = 0.431 mW/g Maximum value of SAR (measured) = 0.977 mW/g A - 8 Date/Time: 2005/8/30 16:16:02 Test Laboratory: Advance Data Technology WUSBF54G-Horizontal-N800C-11b-Mode 1 DUT: Wireless-G USB Adapter with Wi-Fi Finder ; Type: WUSBF54G ; Test Frequency: 2462 MHz Communication System: 802.11b ; Frequency: 2462 MHz ; Duty Cycle: 1:1 ; Modulation type: CCK Medium: MSL2450 Medium parameters used: f = 2462 MHz; σ = 2.01 mho/m; ε r = 50.5; ρ = 1000 kg/m 3 ; Liquid level : 152mm Phantom section: Flat Section ; Separation distance : 7 mm (The bottom side of the EUT to the Phantom) Antenna type : Internal Antenna ; Air temp. : 22.1 degrees ; Liquid temp. : 21.6 degrees DASY4 Configuration: - Probe: ET3DV6 - SN1790 ; ConvF(4.35, 4.35, 4.35) ; Calibrated: 2004/12/20 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579 ; Calibrated: 2005/3/23 - Phantom: SAM 12 ; Type: SAM V4.0 ; Serial: TP 1202 - Measurement SW: DASY4, V4.5 Build 19 ; Postprocessing SW: SEMCAD, V1.8 Build 146 High Channel 11/Area Scan (5x9x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.991 mW/g High Channel 11/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 18.0 V/m Peak SAR (extrapolated) = 2.11 W/kg SAR(1 g) = 0.905 mW/g; SAR(10 g) = 0.446 mW/g Maximum value of SAR (measured) = 1.02 mW/g A - 9 A - 10 Date/Time: 2005/8/30 16:35:50 Test Laboratory: Advance Data Technology WUSBF54G-Horizontal-N800C-11g-Mode 2 DUT: Wireless-G USB Adapter with Wi-Fi Finder ; Type: WUSBF54G ; Test Frequency: 2412 MHz Communication System: 802.11g ; Frequency: 2412 MHz ; Duty Cycle: 1:1 ; Modulation type: OFDM Medium: MSL2450 Medium parameters used: f = 2412 MHz; σ = 1.94 mho/m; ε r = 50.7; ρ = 1000 kg/m 3 ; Liquid level : 152mm Phantom section: Flat Section ; Separation distance : 7 mm (The bottom side of the EUT to the Phantom) Antenna type : Internal Antenna ; Air temp. : 22.1 degrees ; Liquid temp. : 21.6 degrees DASY4 Configuration: - Probe: ET3DV6 - SN1790 ; ConvF(4.35, 4.35, 4.35) ; Calibrated: 2004/12/20 - Sensor-Surface: 4mm (Mechanical Surface Detection) - Electronics: DAE3 Sn579 ; Calibrated: 2005/3/23 - Phantom: SAM 12 ; Type: SAM V4.0 ; Serial: TP 1202 - Measurement SW: DASY4, V4.5 Build 19 ; Postprocessing SW: SEMCAD, V1.8 Build 146 Low Channel 1/Area Scan (5x9x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.708 mW/g Low Channel 1/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 15.9 V/m Peak SAR (extrapolated) = 1.45 W/kg SAR(1 g) = 0.642 mW/g; SAR(10 g) = 0.312 mW/g Maximum value of SAR (measured) = 0.722 mW/g A - 11 Date/Time: 2005/8/30 16:53:03 Test Laboratory: Advance Data Technology WUSBF54G-Horizontal-N800C-11g-Mode 2 DUT: Wireless-G USB Adapter with Wi-Fi Finder ; Type: WUSBF54G ; Test Frequency: 2437 MHz Communication System: 802.11g ; Frequency: 2437 MHz ; Duty Cycle: 1:1 ; Modulation type: OFDM Medium: MSL2450 Medium parameters used: f = 2437 MHz; σ = 1.98 mho/m; ε r = 50.6; ρ = 1000 kg/m 3 ; Liquid level : 152mm Phantom section: Flat Section ; Separation distance : 7 mm (The bottom side…

Text truncated - open the document above for the full version.

B - 1 APPENDIX B: ADT SAR MEASUREMENT SYSTEM C - 1 APPENDIX C: PHOTOGRAPHS OF SYSTEM VALIDATION

FCC ID: Q87-WUSBF54G Report no.: SA940826L011Report Format Version 2.0.2 SAR TEST REPORT REPORT NO.: SA940826L01 MODEL NO.: WUSBF54G RECEIVED: Aug. 26, 2005 TESTED: Aug. 30, 2005 ISSUED: Sep. 05, 2005 APPLICANT: Cisco-Linksys LLC ADDRESS: 121 Theory Drive, Irvine, CA 92617 (USA) ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 36 pages in total except Appendix. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA No. 2177-01 FCC ID: Q87-WUSBF54G Report no.: SA940826L012Report Format Version 2.0.2 TABLE OF CONTENTS 1.CERTIFICATION.......................................................................................................3 2.GENERAL INFORMATION........................................................................................4 2.1GENERAL DESCRIPTION OF EUT.......................................................................4 2.2GENERAL DESCRIPTION OF APPLIED STANDARDS.........................................5 2.3GENERAL INOFRMATION OF THE SAR SYSTEM................................................5 2.4GENERAL DESCRIPTION OF THE SPATIAL PEAK SAR EVALUATION...............8 3.DESCRIPTION OF SUPPORT UNITS....................................................................12 4.DESCRIPTION OF TEST MODES AND CONFIGURATIONS.................................13 4.1.DESCRIPTION OF ANTENNA LOCATION...........................................................13 4.2.DESCRIPTION OF ASSESSMENT POSITION.....................................................14 4.3.DESCRIPTION OF TEST MODE..........................................................................15 4.4.SUMMARY OF TEST RESULTS...........................................................................15 5.TEST RESULTS......................................................................................................16 5.1TEST PROCEDURES..........................................................................................16 5.2MEASURED SAR RESULTS................................................................................18 5.3SAR LIMITS..........................................................................................................20 5.4RECIPES FOR TISSUE SIMULATING LIQUIDS..................................................21 5.5TEST EQUIPMENT FOR TISSUE PROPERTY....................................................23 6.SYSTEM VALIDATION............................................................................................24 6.1TEST EQUIPMENT..............................................................................................24 6.2TEST PROCEDURE.............................................................................................25 6.3VALIDATION RESULTS........................................................................................27 6.4SYSTEM VALIDATION UNCERTAINTIES............................................................28 7.MEASUREMENT SAR PROCEDURE UNCERTAINTIES........................................29 7.1.PROBE CALIBRATION UNCERTAINTY...............................................................29 7.2.ISOTROPY UNCERTAINTY.................................................................................30 7.3.BOUNDARY EFFECT UNCERTAINTY.................................................................30 7.4.PROBE LINEARITY UNCERTAINTY....................................................................31 7.5.READOUT ELECTRONICS UNCERTAINTY........................................................31 7.6.RESPONSE TIME UNCERTAINTY......................................................................31 7.7.INTEGRATION TIME UNCERTAINTY..................................................................32 7.8.PROBE POSITIONER MECHANICAL TOLERANCE...........................................33 7.9.PROBE POSITIONING.........................................................................................33 7.10.PHANTOM UNCERTAINTY..................................................................................34 7.11.DASY4 UNCERTAINTY BUDGET........................................................................35 8.INFORMATION ON THE TESTING LABORATORIES.............................................36 APPENDIX A: TEST CONFIGURATIONS AND TEST DATA APPENDIX B: ADT SAR MEASUREMENT SYSTEM APPENDIX C: PHOTOGRAPHS OF SYSTEM VALIDATION APPENDIX D: SYSTEM CERTIFICATE & CALIBRATION FCC ID: Q87-WUSBF54G Report no.: SA940826L013Report Format Version 2.0.2 1. CERTIFICATION PRODUCT: Wireless-G USB Adapter with Wi-Fi Finder MODEL: WUSBF54G BRAND: Linksys APPLICANT: Cisco-Linksys LLC TESTED: Aug. 30, 2005 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1093), FCC OET Bulletin 65, Supplement C (01-01), RSS-102 The above equipment has been tested by Advance Data Technology Corporation, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY :, DATE:Sep. 05, 2005 Wendy Liao TECHNICAL ACCEPTANCE:, DATE:Sep. 05, 2005 Responsible for RF Stanely Hsu APPROVED BY:, DATE:Sep. 05, 2005 Cody Chang / Deputy Manager FCC ID: Q87-WUSBF54G Report no.: SA940826L014Report Format Version 2.0.2 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT PRODUCT Wireless-G USB Adapter with Wi-Fi Finder MODEL NO. WUSBF54G POWER SUPPLY 5.0Vdc from host equipment CLASSIF…

Text truncated - open the document above for the full version.

FCC ID: Q87-WUSBF54G Report No.: RF940826L011Report Format Version 2.0.3 FCC TEST REPORT REPORT NO.: RF940826L01 MODEL NO.: WUSBF54G RECEIVED: Aug. 17, 2005 TESTED: Aug. 17 ~ Aug. 27, 2005 ISSUED: Aug. 31, 2005 APPLICANT: Cisco-Linksys LLC ADDRESS: 121 Theory Drive, Irvine, CA 92617 (USA) ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: 47 14 th Lin, Chiapau Tsun, Linko, Taipei, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Kueishan, Taoyuan, Taiwan, R.O.C. This test report consists of 62 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA No. 2177-01 FCC ID: Q87-WUSBF54G Report No.: RF940826L012Report Format Version 2.0.3 Table of Contents 1CERTIFICATION.........................................................................................................4 2SUMMARY OF TEST RESULTS.................................................................................5 2.1MEASUREMENT UNCERTAINTY..............................................................................5 3GENERAL INFORMATION.........................................................................................6 3.1GENERAL DESCRIPTION OF EUT...........................................................................6 3.2DESCRIPTION OF TEST MODES.............................................................................7 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST.........................................................7 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL..............................8 3.3GENERAL DESCRIPTION OF APPLIED STANDARDS...........................................10 3.4DESCRIPTION OF SUPPORT UNITS.....................................................................10 4TEST TYPES AND RESULTS...................................................................................11 4.1CONDUCTED EMISSION MEASUREMENT............................................................11 4.1.1LIMITS OF CONDUCTED EMISSION MEASUREMENT..........................................11 4.1.2TEST INSTRUMENTS..............................................................................................11 4.1.3TEST PROCEDURES..............................................................................................12 4.1.4DEVIATION FROM TEST STANDARD.....................................................................12 4.1.5TEST SETUP...........................................................................................................13 4.1.6EUT OPERATING CONDITIONS.............................................................................13 4.1.7TEST RESULTS.......................................................................................................14 4.2RADIATED EMISSION MEASUREMENT.................................................................20 4.2.1LIMITS OF RADIATED EMISSION MEASUREMENT...............................................20 4.2.2TEST INSTRUMENTS..............................................................................................21 4.2.3TEST PROCEDURES..............................................................................................22 4.2.4DEVIATION FROM TEST STANDARD.....................................................................22 4.2.5TEST SETUP...........................................................................................................23 4.2.6EUT OPERATING CONDITIONS.............................................................................23 4.2.7TEST RESULTS.......................................................................................................24 4.36dB BANDWIDTH MEASUREMENT........................................................................31 4.3.1LIMITS OF 6dB BANDWIDTH MEASUREMENT......................................................31 4.3.2TEST INSTRUMENTS..............................................................................................31 4.3.3TEST PROCEDURE.................................................................................................32 4.3.4DEVIATION FROM TEST STANDARD.....................................................................32 4.3.5TEST SETUP...........................................................................................................32 4.3.6EUT OPERATING CONDITIONS.............................................................................32 4.3.7TEST RESULTS...................................…

Text truncated - open the document above for the full version.