QIE0738-02Wireless Duplex Receptacle

LOM-15 102609 LOM-15 by EVOLVE GUEST CONTROLS 1 LOM-15 LOM-15 dupLex receptacLe The LOM-15 Duplex Receptacle is a component of the HomePro lighting control system. Wire the Duplex Receptacle in place of a standard receptacle according to the diagram above and program from the Wireless Controller to operate loads. Inclusion of this Receptacle on the IR-100 Wireless Controller menu allows remote ON/OFF control of loads connected to the controlled outlet. The other outlet remains powered all the time. This LOM-15 Duplex Receptacle is designed to work with other Evolve enabled devices. Evolve nodes of other types can be included in the system and will also act as repeaters if they support this function of repeating the signal received, to other modules in the system. this product supports 40Kbps data transmission. This product can also be used for networking support in systems that stream metadata. An example might include transmission of information from audio devices such as song title, artist, and album information to various displays around the home. As part of a Evolve network, the LOM-15 will also act as a wireless repeater to insure that commands intended for another device in the network are received. This is useful when the device would otherwise be out of the radio range of the wireless controller. There are no field repairable assemblies on this unit. It is covered by a one year limited warranty. If service is needed, the unit must be returned where purchased. daNGer! ShOcK hazard. Read and understand these instructions before installing. This device is intended for installation in accordance with the National Electric code and local regulations in the United States, or the Canadian Electrical Code and local regulations in Canada. It is recommended that a qualified electrician perform this installation. Make sure the total load controlled does not exceed 1800 watts. For indoor use only. Retain instructions for future use. INStaLLatION Wire this Receptacle in place of a current receptacle according to the diagram above. Use copper wire only, or the equivalent. See the IR-100 Wireless Controller operating instructions to add this module under the command of the Wireless Controller. INcLudING LOM-15 tO the NetwOrK Step 1.. Prepare the Controller to include a unit to the network , by adding it to a group (method of adding a node to the network). Refer to controller instructions. Note: This module must be “Included in the Net- work” only where it will be permanently installed. The proper operation of this node in the mesh network is dependent on it knowing its location with respect to other nodes. You cannot “test bench” configure this module, then install. Radio Frequency Controlled, 120 VAC, 15A, Duplex Receptacle, Rel. 2.1 Controlled Outlet Always Powered Outlet LOM-15 102609 LOM-15 by EVOLVE GUEST CONTROLS 2 Step 2. the LOM-15 must be in its permanently installed location. Tap the button on the face of the LOM-15 once when your controller indicates (to include in the network). Step 3. You should see an indication on your Controller that the “DEvICE WAS INCLUDED” in the network. NOte: If you have trouble adding the LOM-15 to a group it may be that the Home ID and Node ID were not cleared from it after testing. You must first “RESET UNIT” with your controller to remove it from the network. If using the IR-100 select “SETUP” and scroll to “RESET UNIT” Although adding it to a group includes it in the network, removing it from a group does not remove it from the network. If removed from a group, it functions as a repeater only. “RESET UNIT” removes it from the network. Receptacle Configuration The LOM-15 Receptacle controls the ON and OFF of a load connected to the controlled outlet (see diagram on page one for identification). The other outlet remains powered all the time. A button on the face of the receptacle is used to add the module to the wireless network and be controlled from the wireless controller. With the Wireless Controller, the LOM-15 Receptacle can be turned ON and OFF remotely, and can be included in groups that operate at the same time (a group can also be a single module), and in scenes that set a lighting mood. Local ON and OFF When the button on the face of the LOM-15 is pressed, the power to the controlled outlet will turn on. When the button is pressed again, the the controlled outlet will turn off. Child Protection The LOM-15 controlled outlet can be set in a child protect mode by the Wireless Controller. When this mode is active, a user will have to press the button on the face 3 times rapidly to activate the attached load. The module operates normally when controlled by the Wireless Controller.. Other functions The button on the face of the LOM-15 Receptacle can be used to carry out inclusion (add to a group), association (operate simultane- ously with other nodes), exclusion (remove from group) or reset (remove from network). This is described in more detail in the Advanced Wireless Controller instructions on our web site. The LOM-15 has a blue indicator LED. This LED will turn on when the controlled outlet is on and will turn off when the controlled outlet is off. However, its behavior can be configured as a “night light” (LED ON when the controlled outlet is off). See Configuration section below on how to do it. advaNced OperatION Configuration The LOM-15 supports the Configuration command. The LOM-15 has some features that can be configured (If your controller supports it). The LOM-15 can be configured to operate slightly differently than how it works when you first install it. You can use a HomePro IR-100 Wireless Controller to send Configuration commands (refer to the Setup Menu, Configuration section of the IR-100 instructions). Using the Configuration command you can configure the following: Set this parameter to 0 to have the blue indicator LED show state of controlled outlet (indicator ON = outlet ON). Set this parameter to 1 to have indicator show the…

Text truncated - open the document above for the full version.

Z-Wave ZRR150 Instructions, Series 300, Rel. 2.1 010510 HomePro by ADVANCED CONTROL TECHNOLOGIES, INC. 0738-02 1 ZRR150 HomePro RF Home Automation ZRR150 DUPLEX RECEPTACLE The ZRR150 Duplex Receptacle is a component of the HomePro lighting control system. Wire the Duplex Receptacle in place of a standard receptacle according to the diagram above and program from the Wireless Controller to operate loads. Inclusion of this Receptacle on the ZTH100 Wireless Controller menu allows remote ON/OFF control of loads connected to the controlled outlet. The other outlet remains powered all the time. This ZRR150 Duplex Receptacle is designed to work with other Z-Wave enabled devices. Z-Wave nodes of other types can be included in the system and will also act as repeaters if they support this function of repeating the signal received, to other modules in the system. This product supports 40Kbps data transmission. This product can also be used for networking support in systems that stream metadata. An example might include transmission of information from audio devices such as song title, artist, and album information to various displays around the home. As part of a Z-Wave network, the ZRR150 will also act as a wireless repeater to insure that commands intended for another device in the network are received. This is useful when the device would otherwise be out of the radio range of the wireless controller. There are no field repairable assemblies on this unit. It is covered by a one year limited warranty. If service is needed, the unit must be returned where purchased. DANGER! SHOCK HAZARD. Read and understand these instructions before installing. This device is intended for installation in accordance with the National Electric code and local regulations in the United States, or the Canadian Electrical Code and local regulations in Canada. It is recommended that a qualified electrician perform this installation. Make sure the total load controlled does not exceed 1800 watts. For indoor use only. Retain instructions for future use. INSTALLATION Wire this Receptacle in place of a current receptacle according to the diagram above. Use copper wire only, or the equivalent. See the ZTH100 Wireless Controller operating instructions to add this module under the command of the Wireless Controller. Note: This module must be “Included in the Network” only where it will be permanently installed. The proper operation of this node in the mesh network is dependent on it knowing its location with respect to other nodes. You cannot “test bench” configure this module, then install. Controlled Outlet Always Powered Outlet Radio Frequency Controlled, 120 VAC, 15A, Duplex Receptacle, Series 300, Rel. 2.1 • This product supports Zensor Net Beam technology. Z-Wave ZRR150 Instructions, Series 300 Rel. 2.1 010510 HomePro by ADVANCED CONTROL TECHNOLOGIES, INC. 0738-02 2 INCLUDING ZRR150 TO THE NETWORK STEP 1.. Prepare the Controller to include a unit to the network, by selecting “Groups” and “Add Unit to Group” (method of adding a node to the network). Refer to controller instructions. STEP 2. The ZRR150 must be in its permanently installed location. Tap the button on the face of the ZRR150 once when your controller indicates “Press Button on Unit”. STEP 3. You should see an indication on your Controller that the “Device was Included” in the network. NOTE: If you have trouble adding the ZRR150 to a group it may be that the Home ID and Node ID were not cleared from it after testing. You must first “Reset Unit” with your controller to remove it from the network. If using the ZTH100 select “Setup” and scroll to “Reset Unit” Although adding it to a group includes it in the network, removing it from a group does not remove it from the network. If removed from a group, it functions as a repeater only. “Reset Unit” removes it from the network. Receptacle Configuration The ZRR150 Receptacle controls the ON and OFF of a load connected to the controlled outlet (see diagram on page one for identification). The other outlet remains powered all the time. A button on the face of the receptacle is used to add the module to the wireless network and be controlled from the wireless controller. With the Wireless Controller, the ZRR150 Receptacle can be turned ON and OFF remotely, and can be included in groups that operate at the same time (a group can also be a single module), and in scenes that set a lighting mood. Local ON and OFF When the button on the face of the ZRR150 is pressed, the power to the controlled outlet will turn on. When the button is pressed again, the the controlled outlet will turn off. Child Protection The ZRR150 controlled outlet can be set in a child protect mode by the Wireless Controller. When this mode is active, a user will have to press the button on the face 3 times rapidly to activate the attached load. The module operates normally when controlled by the Wireless Controller.. Other functions The button on the face of the ZRR150 Receptacle can be used to carry out inclusion (add to a group), association (operate simultaneously with other nodes), exclusion (remove from group) or reset (remove from network). This is described in more detail in the Advanced Wireless Controller instructions on our web site. The ZRR150 has a blue indicator LED. This LED will turn on when the controlled outlet is on and will turn off when the controlled outlet is off. However, its behavior can be configured as a “night light” (LED ON when the controlled outlet is off). See Configuration section below on how to do it. ADVANCED OPERATION Configuration The ZRR150 supports the Configuration command. The ZRR150 has some features that can be configured (If your controller supports it). The ZRR150 can be configured to operate slightly differently than how it works when you first install it. You can use a HomePro ZTH100 Wireless Controller to send Configuration commands (refer to the Setup Menu, Configuration section of the ZTH100 instructions)…

Text truncated - open the document above for the full version.

A LOM-15A, (ACT’s ZRR150A [Almond], Duplex Receptacle, Series 300, Release 2.10) Product Label Artwork A !"#$%&'#( !"#$%&!'%(

-02

BUREAU VERITAS TESTREPORTN°:(5210)004-0124 TESTREPORT To:ADVANCEDCONTROL To:- TECHNOLOGIES,INC. Attn:KevinShelow Attn: - Address:8076WoodlandDrive,Indianapolis,INAddress: - 46278 Fax: -- Fax: - E-mail: [email protected] E-mail: - FolderNo.: MEW-09N0168ATHS-8 Factoryname: MEGAWORLDHOLDINGSLTD. Location:UnitJ, 13/F.,WorldTechCentre,95HowMingStreet,KwunTong,HongKong RFControlledDuplexReceptacle Product: ModelNo.:ZRR150W AdditionalModel:ZRR150AIZRR1501/ LOM-15W/ LOM-15A/ LOM-151 SampleNo:(5209)323-0771 Testdate:November25,2009 TestRequested:FCCPart15- 2008 TestMethod: ANSIC63.4- 2003 FCC10:QIE0738-02 Theresultsgivenin thisreportarerelatedto thetestedspecimenof thedescribedelectricalapparatus. CONCLUSION:ThesubmittedsamplewasfoundtoCOMPLYwithrequirementofFCCPart15SubpartC. AuthorizedSignature: Wml JW' ~ Reviewedby:KeithYeung Approviitby:StevenTsang Date:January7,2010 Date:January7,2010 BUREAUVERITASHONGKONGLlMITED- KowloonBayOffice 1/FPacificTradeCentre, 2 KaiHingRoad,KowloonBay, Kowloon,HONGKONG Tel:+85223310888 Fax:+85223310889 www.cps.bureauveritas.com ThisreportISintendedforyourexclusiveuse,Anycopyingorreplicationofthisreport10orforanyotherpersonorentity,oruse ofournameortrademark,ispermittedonlywithourpriorwrittenpermission.Ourreportislimitedtothelestsamplesidentified herein.Theresultssetforthinthisreportarenotnecessarilyindicativeorrepresentativeofthestatisticalqualityorcharacteristicsof thelotfromwhicha testsamplewastakenoranysimilaroridenticalproductunlessspecificallyandexpresslynoted.Ourreport includesallofthetestsrequestedbyyouandtheresultsthereofYoushallhavethirtydaysfromreceiptofthisreporttorequest additionaltestingofthesamplesortonotifyusofanyerrorsoromissionsrelatingtoourreport,provided,however,suchnotice shallbeinwritingandshallspecificallyaddresstheissueyouwishtoraise.AFailuretoraisesuchissuewithintheprescribedtime shallconstituteyourunqualifiedacceptanceofthecompletenessofthisreport,thetestsconductedandthecorrectnessofthereport contents. Page1 of 20 TEST REPORT N°: (5210)004-0124 BUREAU VERITAS HONG KONG LIMITED – Kowloon Bay Office 1/F Pacific Trade Centre, 2 Kai Hing Road, Kowloon Bay, Kowloon,HONG KONG Tel: +852 2331 0888 Fax: +852 2331 0889 www.cps.bureauveritas.com This report is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. Our report is limited to the test samples identified herein. The results set forth in this report are not necessarily indicative or representative of the statistical quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof. You shall have thirty days from receipt of this report to request additional testing of the samples or to notify us of any errors or omissions relating to our report, provided, however, such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Page 2 of 20 Location of the test site Radiated and Conducted emissions measurements are investigated and taken pursuant to the procedures of ANSI C63.4 – 2003. An Open Area Test Site and Full Anechoic Chamber (FCC Listed Site, Registration No. 642151) are set up for investigation and located at : BUREAU VERITAS HONG KONG LIMITED, EMC CENTRE No. 2106-2107, 21/F., Westin Centre, 26 Hung To Road, Kwun Tong, Kowloon, Hong Kong List of measuring equipment Radiated Emission EQUIPMENT MANUFACTURER MODEL NO. SERIAL NO. CALIBRATION DUE EMI TEST RECEIVER R&S ESCI 100379 24-AUG-2010 BILOG ANTENNA SCHAFFNER CBL6112D 25229 31-MAY-2010 OPEN AREA TEST SITE BVCPS N/A N/A 03-JULY-2010 ANECHOIC CHAMBER ALBATROSS M-CDC 80374004499B 07-JULY-2010 HORN ANTENNA SCHWARZBECK BBHA9120D 9120D-692 21-JULY-2010 PREAMPLIFIER SCHWARZBECK BBV9718 9718-152 27-JULY-2010 COAXIAL CABLE SUHNER N/A N/A 11-MAY-2010 SPECTRUM ANALYZER ADVANTEST R3127 111000909 17-DEC-2010 Conducted Emission EQUIPMENT MANUFACTURER MODEL NO. SERIAL NO. CALIBRATION DUE EMI TEST RECEIVER R&S ESCS30 830986/030 26-SEP-2010 LISN R&S ENV216 100024 25-MAR-2010 Remarks:- N/A : Not Applicable or Not Available The measurement instrumentation uncertainty would be taking into consideration on each of the test result TEST REPORT N°: (5210)004-0124 BUREAU VERITAS HONG KONG LIMITED – Kowloon Bay Office 1/F Pacific Trade Centre, 2 Kai Hing Road, Kowloon Bay, Kowloon,HONG KONG Tel: +852 2331 0888 Fax: +852 2331 0889 www.cps.bureauveritas.com This report is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. Our report is limited to the test samples identified herein. The results set forth in this report are not necessarily indicative or representative of the statistical quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof. You shall have thirty days from receipt of this report to request additional testing of the samples or to notify us of any errors or omissions relating to our report, provided, however, such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Page 3 of 20 Equipment Under Test [EUT] Description of Sample: Model Name: RF Controlled Duplex Rece…

Text truncated - open the document above for the full version.

TEST REPORT N°: (5209)343-0600 BUREAU VERITAS HONG KONG LIMITED – Kowloon Bay Office 1/F Pacific Trade Centre, 2 Kai Hing Road, Kowloon Bay, Kowloon,HONG KONG Tel: +852 2331 0888 Fax: +852 2331 0889 www.cps.bureauveritas.com This report is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. Our report is limited to the test samples identified herein. The results set forth in this report are not necessarily indicative or representative of the statistical quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof. You shall have thirty days from receipt of this report to request additional testing of the samples or to notify us of any errors or omissions relating to our report, provided, however, such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Page 23 of 23 Measurement of Conducted Emission Test Set Up Measurement of Radiated Emission Test Set Up ***** End of Report *****