QUUSWTX01REMOTE CONTROL TRANSMITTER

*+ # i Superwinch LLC. 359 Lake Road Dayville, CT 06241, USA tel: 1.860.928.7787 fax: 1.860.963.0811 [email protected] www.superwinch.com Superwinch LTD. Union Mine Road Tavistock, Devon PL19 0NS England tel: +44 (0) 1822 614101 fax: + 44 (0) 1822 615204 [email protected] 98-17449 Rev - 01/24/2012 OWNER’S MANUAL READ AND UNDERSTAND THIS MANUAL BEFORE INSTALLATION AND OPERATION OF YOUR SUPERWINCH PRODUCT CAUTION ! TM WIRELESS REMOTE CONTROL 1 SPANISH WARNING ! CERTUS WIRELESS REMOTE SYSTEM – CONSUMER VERSION Read and understand the manual thoroughly before installing or using the radio remote control. General Information The system operates on a frequency of 433MHZ and utilizes frequency modulation generally known as FM technology. While an FM signal is much less susceptible to electrical interference than an AM signal, there can never be total protection against outside interference. Interference can result from the turning on and off of electronic equipment and can come from proximity to industrial equipment and types of computer equipment. The greatest range will be achieved if the receiver is not enclosed in metal. SAFETY PRECAUTIONS The responsibility for safe installation and operation of this system ultimately rests with you, the operator. Read and understand all safety precautions and operating instructions before installing and operating the system. Careless system operation can result in serious injury and/or property damage. Throughout this manual, you will find notations with the following headings: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. This notation is also used to alert against unsafe practices. CAUTION ! DANGER ! Read Owner's Manual Note: Indicates additional information in the installation and operation procedures of your wireless remote control. The following symbols on the product and in the Owners manual are used: WARNING ! 2 Improper installation or improper use of the remote unit by the user could result in injury or destruction of property. Keep this manual for future reference. SPANISH Misuse or abuse of this equipment could result in injury to the user or others and/or damage to property. The control will be brought to a stop if: 1. the red power button is activated 2. system encounters the same frequency from an outside source 3. five minutes go by since the last transmission These safety features are engineered into the system to protect personnel and equipment and should never be changed, taken out or bypassed. If an emergency situation arises immediately press the red power button on the transmitter see (Fig. 1) 1. Never leave the transmitter unattended. 2. The transmitter is only to be used where there is a clear view of the operating machinery. 3. Do not use more than one transmitter for one receiver box. If you own or purchase a backup transmitter it is important to stow the second transmitter securely. When the system is first put into use, the backup unit should be tested then have its battery removed and the unit should be stored in a secure place to avoid accidental operation, which may result in serious injury or death. 4. Both the transmitter housing and buttons should be checked on a regular basis and, if damaged, the transmitter should be taken out of use. 5. In an emergency situation, pressing the red stop button should immediately activate the stop relay in the receiver. Remove power to the machine. 3 Fig. 1 LED 1 Power Button SPANISH ! AVERTISSEMENT SPANISH Programming the Transmitter Note: Transmitters supplied with the unit are pre-programmed at the factory - DO NOT RE-PROGRAM THEM. Should a new transmitter be purchased it will require programming. To program, follow the instructions below: NOTE: Each of the three (3) buttons needs to be programmed individually OPERATION INSTRUCTIONS RED Power Button Green Button 1 Green Button 2 LED 1 (Fig. 2) Front of Transmitter Green LED Red LED Program Green Button 1: • Press the learn button (See Fig.3 below) 1 time. Wait for the red LED on receiver to flash 1 time. • Press green button 1 on the transmitter and release. • Re-press green button 1 on the transmitter. The red LED on receiver will now flash to indicate that learning is complete for green button 1. Learn Button (Fig.3) 4 The transmitter has one red LED light, see (Fig. 2) which glows when any one of the buttons is depressed; this shows the receiver is sending a signal to the receiver. 1. To use the wireless system, the operator first activates the system by pressing the red power button on the transmitter; a green LED on the receiver will glow as the system is now in operational mode and ready for use. 2. To deactivate the wireless system, press the red power button and the green LED on the receiver turns off as the system is now in standby mode. 3. The power button always has priority and will override all buttons so that it will put the system into standby mode. 4. If the system is idle for 5 minutes or longer, the system will deactivate and go into standby mode and will need to be activated prior to use. Program Red Power Button: • Press the learn button 1 time Wait for the red LED on receiver to flash 1 time • Press the learn button 1 more time Wait for the red LED on receiver to flash 2 times • Press the learn button 1 more time Wait for the red LED on receiver to flash 3 times • Press the red button on the transmitter and release • Re-press the red button on the transmitter The red LED on receiver will now flash to indicate that learning is complete for the red button Your transmitter is now programmed and ready for use Program Green Button 2: • Press the learn button 1 time Wait for the red LED on receiver to flash 1 time • Press the learn button 1 more …

Text truncated - open the document above for the full version.

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 6/4/2012 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name QUUSWTX01 SWTX01 For the product stated above, we request permanent confidentiality for exhibits which contain Operational Description, Block Diagram, and Schematics information. The above exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Scott Saccoccio Name: Scott Saccoccio Company: Superwinch, LLC Address: 359 Lake Road, Putnam, CT 06241 Phone: (860) 928-7787 Fax: (860) 928-1143 Email: [email protected]

APPLICANT: SUPERWINCH, LLC. FCC ID: QUUSWTX01 EXTERNAL PHOTOS

For Receiver Rear Face: www.superwinch.com FCC ID: QUUSWRX01 IC: 5101A-SWRX01 Model #: 98-40299 For Transmitter Rear Face: www.superwinch.com FCC ID: QUUSWTX01 IC: 5101A-SWTX01 Model #: 98-40299

APPLICANT: SUPERWINCH, LLC. FCC ID: QUUSWTX01 INTERNAL PHOTOS FRONT SIDE VIEW REAR VIEW FRONT SIDE VIEW WITH TX MODULE REAR VIEW WITH TX MODULE FRONT SIDE VIEW TX MODULE REAR SIDE VIEW TX MODULE

1 AN1603 Multilayer Chip Antenna for 433.92MHz Wireless Communication (Advance Information) 2 Multilayer Chip Antenna Features yMiniaturized size 16(L)X03(W)X02(H) yLight weight and low profile yOmni-directional in azimuth Applications y433.92MHz wireless communications yModules yOther 433.92MHz Wireless Application Specifications Center frequency Peak gain Operation temperature Storage temperature VSWR Input Impedance Power handling Bandwidth Azimuth beamwidth Polarization 433MHz 0.5dBi -40 ~ +85 °C -40 ~ +85 °C 2.0 (Max) 50 Ohm 3W (Max) 8MHz Omni-directional Linear 3 Pin configuration 2 1 Pin NoPin assignment 1Feed termination 2Solder termination Dimensions symbolDimensions(mm) A16±0.1 B03±0.1 C02±0.02 D02±0.02 4 Recommend Test Board Pattern Top view SMA connector Ground Plane Bottom view 50Ohm Transmission line Unit:cm Board thickness 0.6mm Board material:FR4 Testing Block Network Analyzer DUT Port1 5 Measurement Testing Instrument:Anritsu 37369C VNA(Vector Network Analyzer) VNA calibrate with 1 path reflection only calibration sequence on test board feed point.The test board layout as recommend dimension. 6 Measured Antenna patterns Return loss

FCC PART 15.231 AND IC RSS-210 TEST REPORT LOW POWER UNLICENSED TRANSMITTER Applicant SUPERWINCH, LLC Address 359 LAKE ROAD DAYVILLE CT 06241 FCC ID QUUSWTX01 IC 5101A-SWTX01 Model 98-40299 Product Description REMOTE CONTROL TRANSMITTER Date Sample Received 2/28/2012 Date Tested 3/15/2012 Tested By Nam Nguyen Approved By Mario R. de Aranzeta Timco Report No. 3004AUT11TestReport.doc Test Results Pass Fail THE ATTACHED REPORT SHALL NOT BE REPRODUCED EXCEPT IN FULL WITHOUT THE WRITTEN APPROVAL OF TIMCO ENGINEERING, INC. Testing Certificate #0955-01 849 NW STATE ROAD 45 NEWBERRY, FL 32669 USA PH: 888.472.2424 OR 352.472.5500 FAX: 352.472.2030 EMAIL: [email protected] HTTP://WWW.TIMCOENGR.COM APPLICANT: SUPERWINCH, LLC FCC ID: QUUSWTX01 REPORT: S\SUPERWINCH\3004ZUT11\3004ZUT11TestReport.doc Page 2 of 12 mdea 09.20.2007 TABLE OF CONTENTS GENERAL REMARKS ...................................................................................................... 3 REPORT SUMMARY ....................................................................................................... 4 TEST ENVIRONMENT ..................................................................................................... 4 TEST SETUP................................................................................................................... 4 DUT SPECIFICATION ..................................................................................................... 4 MANUFACTURE DECLARATION OF COMPLIANCE WITH PART 15.231(A) ..................... 5 TEST EQUIPMENT LIST ................................................................................................. 6 TEST PROCEDURES ...................................................................................................... 7 RADIATION INTERFERENCE .......................................................................................... 8 CALCULATION OF DUTY CYCLE .................................................................................. 10 OCCUPIED BANDWIDTH .............................................................................................. 11 POWER LINE CONDUCTED INTERFERENCE ............................................................... 12 APPLICANT: SUPERWINCH, LLC FCC ID: QUUSWTX01 REPORT: S\SUPERWINCH\3004ZUT11\3004ZUT11TestReport.doc Page 3 of 12 mdea 09.20.2007 GENERAL REMARKS The attached report shall not be reproduced except in full without the written permission of Timco Engineering Inc. Summary The device under test does: fulfill the general approval requirements as identified in this test report not fulfill the general approval requirements as identified in this test report Attestations This equipment has been tested in accordance with the standards identified in this test report. To the best of my knowledge and belief, these tests were performed using the measurement procedures described in this report. All instrumentation and accessories used to test products for compliance to the indicated standards are calibrated regularly in accordance with ISO 17025 requirements. Certificate # 0955-01 I attest that the necessary measurements were made, under my supervision, at: Timco Engineering Inc. 849 NW State Road 45 Newberry, Fl 32669 Authorized Signatory Name: Mario de Aranzeta C.E.T. Compliance Engineer/ Lab. Supervisor Date: March/15/2012 APPLICANT: SUPERWINCH, LLC FCC ID: QUUSWTX01 REPORT: S\SUPERWINCH\3004ZUT11\3004ZUT11TestReport.doc Page 4 of 12 mdea 09.20.2007 REPORT SUMMARY Disclaimer The test results only relate to the item tested. Applicable Rule(s) FCC Pt 15.231, Pt 15.209, Pt 15.207, ANSI C63.4: 2003 TEST ENVIRONMENT Test Facility The test sites are located at 849 NW State Road 45 Newberry, FL 32669 USA. Test Condition: Temperature: 26ºC Relative humidity: 50% TEST SETUP Test Exercise (e.g software description, test signal, etc.): The DUT was placed in continuous transmit mode of operation. Deviation from the standard(s) No deviation from the standard(s) Modification to the DUT: No modification was made to the DUT. Supporting Peripheral Equipment Not applicable. The device is a stand-alone remote control radio. DUT SPECIFICATION Applicant SUPERWINCH, LLC Description REMOTE CONTROL TRANSMITTER FCC ID QUUSWTX01 IC 5101A-SWTX01 Model 98-40299 Frequency Range 433.92 MHz DUT Power Source 110–120Vac/50– 60Hz DC Power Battery Operated Exclusively Test Item Prototype Pre-Production Production Type of Equipment Fixed Mobile Portable APPLICANT: SUPERWINCH, LLC FCC ID: QUUSWTX01 REPORT: S\SUPERWINCH\3004ZUT11\3004ZUT11TestReport.doc Page 5 of 12 mdea 09.20.2007 MANUFACTURE DECLARATION OF COMPLIANCE WITH PART 15.231(A) Item Description Yes No 1 Does this device transmit a signal that is only used to control another device? X 2 Does this device send data with this control signal? X 3 Does this device send data? Data is, things like: temperature, wind direction, fluid amount, rate of flow, etc. X 4 Does this device transmit continuously or automatically? X 5 If manually operated does this device stop transmitting within 5 seconds of releasing the button? X 6 If automatically operated does it deactivate 5 seconds after activation? N/A 7 Does it transmit at regular predetermined intervals? X 8 Does it poll or send supervisory information? X If yes does it do a system integrity check? How often? X 9 Is this a fire, security or safety of life device? X If YES does the device stop transmitting after the alarm condition is satisfied? 10 Duty cycle: Maximum on-time? If YES, on-time in 100 ms? If Other, please specify here On time in 11 Modulation technique: Please specify the modulation of the test sample, FM, or AFSK, or FSK, or on-off keying, or others? APPLICANT: SUPERWINCH, LLC FCC ID: QUUSWTX01 REPORT: S\SUPERWINCH\3004ZUT11\3004ZUT11TestReport.doc Page 6 of 12 mdea 09.20.2007 TEST EQUIPMENT LIST Device Manufacturer Model Serial Number Cal/Char Date Due Date 3-Meter Semi- Anechoic Chamber Panashield N/A N/A Listed 5/10/10 5/10/12 AC Voltm…

Text truncated - open the document above for the full version.