QVEZW4U2Remote Control

User Guide INTRODUCTION This product is a remote control. The Zagg remote is used only with the Teleportall Set Box. The purpose of the remote is to control the set up box. Such functions as to change channel, change volume, etc. The following is a picture of the remote: OPERATION Before using the remote please make sure the set up box is ready for operation. For this please read the set up manual. a) Once the set up box is ready for operation, pair the remote to the set up box. This is done by following the instructions described in the monitor connected to the set up box. b) Point you remote to the set up box. c) Press the key you desire. INFORMATION TO USER This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced radio/TV technician for help Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Authority to Act as Agent to the Federal Communications Commission On our behalf, I appoint Nemko USA, Inc. to act as agent in the preparation of this application for equipment authorization to the Federal Communications Commission. I certify that submitted Exhibits properly describe the device or system for which equipment authorization is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Commission's regulations will have affixed to it a label identical to that submitted for approval with this application. APPLICANT ANTI-DRUG ABUSE CERTIFICATION: In signing this letter, Applicant certifies that, in the case of an individual applicant, he or she is not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a), or, in the case of a non-individual applicant (e.g. corporation, partnership or other unincorporated association), no party to the application is subject to a denial of federal benefits, that includes FCC benefits, pursuant to that section. For the definition of a "party" for these purposes, see 47 CFR 1.2002(b). Dated this 4th Day of February, 2010 Agency agreement expiration date: 04 September 2010 Company: SMK By: Leon Gateno Title: SR RF Engineer Telephone: 619-216-6425 Applicant: SMK

Nemko Canada Inc 303 River Road Ottawa K1V 1H2 Canada IC: 3683B-ZW4U2 Model: Zagg FCC ID: QVEZW4U2 Request for Module Label exemption The Zagg remote is approximately 2 inches x 4 inches and is about the size of a human palm. SMK requests exception to the requirement of the two-part warning and MFG to be printed on the label of the device. The warning is in the user’s guide. Dated this 4 th Day of Feb 2010 RF Engineer

2/04/10 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification FCC ID: QVEZW4U2 Product Name: Zagg Remote Control Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: • Schematics • Block diagram • BOM • Operation Description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 4 th Day of Feb 2010 RF Engineer

FCC ID: QVEZW4U2 IC: 3683B-ZW4U2 PMS Warm Gray 6C This View for Reference Only SCALE: UNIT: APPROVED CHECKED DESCRIPTIONSIZE: DESIGNED SHEET: 1 of 1 ISSUED REV. Massoud Niakan 4/6/10 Jim Tickle 4/6/10 Pat Bair 4/5/10 1/1 MM AW, Housing, Bottom, Lower, Teleportall DRAWING NO. 101RXTH016-01E B2 REVISION HISTORY REV DESCRIPTION SIGN APP RELEASED PER ECO #L-3492 1 4/6/2010 DATE PB JT REVISED PER ECO #L-3501 2 4/13/10

Nemko USA, Inc. 11696 Sorrento Valley Rd., Suite F San Diego, CA 92121-1024 Phone (858) 755-5525 Fax (858) 452-1810 CERTIFICATION TEST REPORT In Accordance With: FCC Part 15 Subpart C, 15.249 IC RSS-210 Issue 7 June 2007 Applicant: SMK Electronics Corp. USA 1055 Tierra Del Rey Chula Vista, CA 91910 Equipment Under Test : ZWAVE Remote Model: ZAGG FCC ID: QVEZW4U2 IC: 3683B-ZW4U2 Tested By: Nemko USA Inc. 11696 Sorrento Valley Road, Suite F San Diego, CA 92121 Test Report: 2010 03146433 FCCTX Date: March 18, 2010 Project number: 40427-1 Nex Number: 146433 Total Number of Pages: 15 Nemko USA, Inc. 11696 Sorrento Valley Road, Suite F, San Diego, CA 92121 Phone (858) 755-5525 Fax (858) 452-1810 FCC ID: QVEZW4U2 Report Number: 2010 03146433 FCCTX IC: 3683B-ZW4U2 Specification: FCC Part 15 Subpart C, 15.249 Section 1. Summary of Test Results General All measurements are traceable to national standards These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with Part 15; Subpart C. Radiated tests were conducted is accordance with ANSI C63.4-2003. Radiated emissions are made on an open area test site. A description of the test facility is on file with the FCC. The assessment summary is as follows: Apparatus Assessed: ZWAVE Remote Model: ZAGG Specification: FCC Part 15 Subpart C, 15.249 IC RSS-210 Issue 7 June 2007 Date Received in Laboratory: March 17, 2010 Compliance Status: Complies Exclusions: None Non-compliances: None Nemko USA, Inc. 11696 Sorrento Valley Road, Suite F, San Diego, CA 92121 Phone (858) 755-5525 Fax (858) 452-1810 FCC ID: QVEZW4U2 Report Number: 2010 03146433 FCCTX IC: 3683B-ZW4U2 Specification: FCC Part 15 Subpart C, 15.249 Report Release History REVISION DATE COMMENTS - March 18, 2010 Prepared By: Alan Laudani - March 18, 2010 Initial Release: Alan Laudani Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. Nemko USA Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko USA Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. TESTED BY: __ Date: March 18, 2010 Alan Laudani, EMC Test Engineer Nemko USA, Inc. 11696 Sorrento Valley Road, Suite F, San Diego, CA 92121 Phone (858) 755-5525 Fax (858) 452-1810 FCC ID: QVEZW4U2 Report Number: 2010 03146433 FCCTX IC: 3683B-ZW4U2 Specification: FCC Part 15 Subpart C, 15.249 TABLE OF CONTENTS Section 1. Summary of Test Results....................................................................... 2 Report Release History ................................................................................................................................. 3 Section 2: Equipment Under Test ................................................................................ 5 2.1 Product Identification........................................................................................................................ 5 2.2 Samples Submitted for Assessment ................................................................................................5 2.3 Theory of Operation ......................................................................................................................... 6 2.4 Technical Specifications of the EUT ................................................................................................ 6 Section 3: Test Conditions ........................................................................................... 7 3.1 Specifications ................................................................................................................................... 7 3.2 Deviations From Laboratory Test Procedures ................................................................................. 7 3.3 Test Environment ............................................................................................................................. 7 3.4 Test Equipment ................................................................................................................................ 8 Section 4: Observations ............................................................................................... 9 4.1 Modifications Performed During Assessment .................................................................................. 9 4.2 Record Of Technical Judgements.................................................................................................... 9 4.3 EUT Parameters Affecting Compliance ........................................................................................... 9 4.4 Tests Deleted ................................................................................................................................... 9 4.5 Additional Observations ................................................................................................................... 9 Section 5: Results Summary ...................................................................................... 10 5.1 Results Summary........................................................................................................................... 10 Appendix A: Test Results............................................................................................. 1 Power line Conducted Emissions / Receiver or Stand-by Mode .................................................................. 1 Occupied Bandwidth ..................................................................................................…

Text truncated - open the document above for the full version.