QYPPWR0703Bluetooth Remote

Version 1.1 – May 2005 Doc # 2520 Polymap Wireless Confidential and Proprietary. PWR-07-03 Remote module May 20, 2005 Introduction: The PWR-07-03 provides a simple way for a LifeScan OneTouch Ultra device to transmit its data via Bluetooth ® connectivity. When a measurement is taken on the OneTouch, this module automatically retrieves the measurement and tries to transmit it to a receiving station. Should that station be unavailable, it will periodically retry the transmission, and eventually shut itself down again. Connection The device is connected to the OneTouch Ultra through a phono jack. To set up the device for the first time, please follow these steps: Figure 1: positioning of PWR-07-03 device. Please note that cable must pass through mesh, which may need to have a ¼” cut made in it near the bottom left corner. 1) Thread the phono jack through the mesh of the OneTouch Ultra case. You may have to cut a ¼” slit to do this (please see figure above). Version 1.1 – May 2005 Doc # 2520 Polymap Wireless Confidential and Proprietary. 2) Plug the jack into the bottom of the OneTouch Ultra unit, being careful to press the connector firmly in place 3) Insert the 28L battery into the module. Please observe correct polarity or the device will not function correctly. 4) Close the zippered case. The module is ready to use. Appearance: Figure 2: PWR-07-03 with its battery. Usage Take a measurement as you normally would. When the test strip is removed, the red indicator light will turn on, and the glucose meter will display “PC”. This is normal, and can be ignored. Both the light, and, eventually, the “PC” indication, will turn off on their own. There is nothing the user need do other than take the measurements themselves. Indicator light The device incorporates a small red LED. This indicator will light shortly after you remove a test strip from the glucose meter. It will turn itself off after the data is successfully transmitted. Should the data fail to transmit immediately, the device will schedule multiple retries, and the light may remain on as long as a half hour. Please note that any measurements not transmitted immediately are stored and transmitted along with later measurements. Version 1.1 – May 2005 Doc # 2520 Polymap Wireless Confidential and Proprietary. Figure 3: Indicator light shows through mesh Battery warning The module is currently designed to be connected to a OneTouch Ultra. If you disconnect it, by removing the meter from its case, please also remove the battery from the PWR-07-03 module to avoid draining it unnecessarily. If the module is left on the shelf with a battery in it, disconnected from the Ultra meter, it will rapidly exhaust its battery. Regulatory Statements “Modifications made to the product, unless expressly approved by Polymap Wireless, could void the user’s authority to operate the equipment” “To comply with FCC RF exposure compliance requirements, this device and its antenna must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. NOTE: this product has NOT received FDA clearance. CAUTION: this system should only be used as part of an approved protocol. Version 1.1 – May 2005 Doc # 2520 Polymap Wireless Confidential and Proprietary. Polymap Wireless 310 S. Williams Blvd. Ste. 346 Tucson, AZ 85711 (520) 747-1811 PWR-07-03-OA FCC ID: QYPPWR0703 We declare under our sole responsibility that the product Polymap Wireless Remote PWR-07-01 complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Tested to comply with FCC Standards For Home or Office Use NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device , pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: — Reorient or locate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help.

May 23, 2005 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Rd Columbia, MD 21046 re: Request for Confidentiality In reference to the application under FCC ID: QYPPWR0703 and pursuant to Sections 0.457(d)(l)(ii) and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of the accompanying information as outlined below: Schematics Block Diagrams Theory of Operation . These documents contain detailed system and equipment description and related information about the product that Polymap Wireless considers to be proprietary, confidential, and a custom design and, otherwise, would not release to the general public. Since this design is a basis from which future technological products will evolve, Polymap Wireless considers that this information would be of benefit to its competitors, and that disclosure of the information in these documents would give competitors an unfair advantage in the market. Sincerely, Pierre Landau, PhD President 310 S. Williams Blvd. Suite 346 Tucson, AZ 85711 t: 520.747.1811 f: 520.747.9408 www.polymap.net

KRD01-00A05-01IR KOSAN I & T Co., Ltd. Charge Confirm Approval Specification Sheet Object Monopole Cable Antenna / / / Customer Polymap REV. IR Page 1 of 4 Model name KBI-CO-24 Date Dec 2, 2003 System Bluetooth Scale Written by Jin Myung Kim Electrical Specification Frequency Range 2.4 ~ 2.4835 (GHz) Band Width 83.5 (MHz) V.S.W.R less than 2 : 1 Gain Peak 3 dBi Input Impedance 50 ( Ω ) Polarization Linear Mechanical Specification Antenna Size 54.5 × 8 × 1 mm (L×W×t) Weight 3 (g) Radiator Material FR-4 Cable Ass’y IPEX Coaxial Cable Ass’y Cable Length 380mm ± 5mm Cable Diameter 1.03 mm Operation Temperature -20 ~ 90 ( ̊ C) Operation Humidity 0 ~ 90 (%) Option Others Fig 1. RETURN LOSS Fig 2. VSWR Fig 4. RADIATION PATTERN ELEVATION PATTERN AZIMUTH PATTERN

1 Helen Zhao Subject:FW: Polymap Wireless LLC , FCC ID: QYPPWR0703, Assessment NO.: AN05T4815, Notice#1 2520 - Polymap Wireless User D... -----Original Message----- From: Danielle Zhan Sent: Friday, May 27, 2005 3:54 PM To: Helen Zhao Subject: RE: Polymap Wireless LLC , FCC ID: QYPPWR0703, Assessment NO.: AN05T4815, Notice#1 Dear Helen, Attached please find revised user manual for your further review. Thanks, Danielle -----Original Message----- From: Compliance Certification Services [mailto:[email protected]] Sent: Friday, May 27, 2005 11:53 AM Subject: Polymap Wireless LLC , FCC ID: QYPPWR0703, Assessment NO.: AN05T4815, Notice#1 Question #1: Please add RF exposure statement into the user manual. Best Regards, Helen The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 30 days of the original e-mail date may result in application dismissal and forfeiture of the filing fee. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the e-mail address listed below the name of the sender.

PROPOSED FCC ID LABEL AND LOCATION POLYMAP WIRELESS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID : QYPPWR0703 FCC ID LABEL

FCC CFR47 PART 15 SUBPART C CERTIFICATION TEST REPORT FOR BLUETOOTH REMOTE MODEL NUMBER: PWR-07-03 FCC ID: QYPPWR0703 REPORT NUMBER: 05U3432-1 ISSUE DATE: MAY 17, 2005 Prepared for POLYMAP WIRELESS 310 S. WILLIAMS BLVD., STE. 346 TUSCON, AZ 85711 U.S.A. Prepared by COMPLIANCE ENGINEERING SERVICES, INC. d.b.a. COMPLIANCE CERTIFICATION SERVICES 561F MONTEREY ROAD, MORGAN HILL, CA 95037, USA TEL: (408) 463-0885 FAX: (408) 463-0888 REPORT NO: 05U3432-1 DATE: MAY 17, 2005 EUT: BLUETOOTH REMOTE FCC ID: QYPPWR0703 Page 2 of 67 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. Revision History Rev. Revisions Revised By REPORT NO: 05U3432-1 DATE: MAY 17, 2005 EUT: BLUETOOTH REMOTE FCC ID: QYPPWR0703 Page 3 of 67 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS............................................................................................. 4 2. TEST METHODOLOGY .................................................................................................................. 5 3. FACILITIES AND ACCREDITATION .......................................................................................... 5 4. CALIBRATION AND UNCERTAINTY.......................................................................................... 5 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................................. 5 4.2. MEASUREMENT UNCERTAINTY ............................................................................................... 5 5. EQUIPMENT UNDER TEST............................................................................................................6 5.1. DESCRIPTION OF EUT ..............................................................................................................6 5.2. MAXIMUM OUTPUT POWER .................................................................................................... 6 5.3. DESCRIPTION OF AVAILABLE ANTENNAS ............................................................................. 6 5.4. SOFTWARE AND FIRMWARE .................................................................................................... 6 5.5. WORST-CASE CONFIGURATION AND MODE......................................................................... 6 5.6. DESCRIPTION OF TEST SETUP ................................................................................................ 8 6. TEST AND MEASUREMENT EQUIPMENT .............................................................................. 10 7. LIMITS AND RESULTS ................................................................................................................. 11 7.1. ANTENNA PORT CHANNEL TESTS ......................................................................................... 11 7.1.1. 20 dB BANDWIDTH ......................................................................................................... 11 7.1.2. HOPPING FREQUENCY SEPARATION......................................................................... 15 7.1.3. NUMBER OF HOPPING CHANNELS ............................................................................. 17 7.1.4. AVERAGE TIME OF OCCUPANCY ............................................................................... 21 7.1.5. PEAK OUTPUT POWER .................................................................................................. 24 7.1.6. MAXIMUM PERMISSIBLE EXPOSURE ........................................................................ 28 7.1.7. AVERAGE POWER........................................................................................................... 31 7.1.8. PEAK POWER SPECTRAL DENSITY ............................................................................ 32 7.1.9. CONDUCTED SPURIOUS EMISSIONS.......................................................................... 36 7.2. RADIATED EMISSIONS.............................................................................................................45 7.2.1. TRANSMITTER RADIATED SPURIOUS EMISSIONS ................................................. 45 7.2.2. TRANSMITTER RADIATED EMISSIONS ABOVE 1 GHZ .......................................... 48 7.2.3. WORST-CASE RADIATED EMISSIONS BELOW 1 GHz ............................................. 57 8. SETUP PHOTOS .............................................................................................................................. 61 REPORT NO: 05U3432-1 DATE: MAY 17, 2005 EUT: BLUETOOTH REMOTE FCC ID: QYPPWR0703 Page 4 of 67 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: POLYMAP WIRELESS 310 S. WILLIAMS BLVD., SUITE 346 TUSCON, AZ 85711 U.S.A. EUT DESCRIPTION: BLUETOOTH REMOTE MODEL: PWR-07-03 SERIAL NUMBER: 00043E68B87E DATE TESTED: MAY 10 –MAY 11, 2005 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 15 SUBPART C NO NON-COMPLIANCE NOTED Compliance Certification Services, Inc. tested the above equipment in accordance with the requirements set forth in the above standards. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by Compliance Certification Services and a…

Text truncated - open the document above for the full version.

REPORT NO: 05U3432-1 DATE: MAY 17, 2005 EUT: BLUETOOTH REMOTE FCC ID: QYPPWR0703 Page 61 of 67 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. 8. SETUP PHOTOS ANTENNA PORT CONDUCTED RF MEASUREMENT SETUP ANTENNA PORT CONDUCTED PHOTO REPORT NO: 05U3432-1 DATE: MAY 17, 2005 EUT: BLUETOOTH REMOTE FCC ID: QYPPWR0703 Page 62 of 67 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. RADIATED RF MEASUREMENT SETUP FOR PORTABLE CONFIGURATION X-AXIS FRONT PHOTO REPORT NO: 05U3432-1 DATE: MAY 17, 2005 EUT: BLUETOOTH REMOTE FCC ID: QYPPWR0703 Page 63 of 67 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. X-AXIS BACK PHOTO REPORT NO: 05U3432-1 DATE: MAY 17, 2005 EUT: BLUETOOTH REMOTE FCC ID: QYPPWR0703 Page 64 of 67 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. Y-AXIS FRONT PHOTO REPORT NO: 05U3432-1 DATE: MAY 17, 2005 EUT: BLUETOOTH REMOTE FCC ID: QYPPWR0703 Page 65 of 67 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. Y-AXIS BACK PHOTO REPORT NO: 05U3432-1 DATE: MAY 17, 2005 EUT: BLUETOOTH REMOTE FCC ID: QYPPWR0703 Page 66 of 67 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. Z-AXIS FRONT PHOTO REPORT NO: 05U3432-1 DATE: MAY 17, 2005 EUT: BLUETOOTH REMOTE FCC ID: QYPPWR0703 Page 67 of 67 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. END OF REPORT Z-AXIS BACK PHOTO