QZ9-CG3Base Station

Inspection marks and declarations of conformity Statement of Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. To comply with the FCC RF exposure compliance requirements, the device must be installed to provide a separation distance of at least 20cm from all persons. Canadian market only This device complies with ISED Canada’s license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003. CAN ICES-3 (B)/NMB-3(B) Declaration on exposure to radiation: This equipment conforms with the IC limits of exposure to radiation drawn up for a non-controlled environment. This equipment should be installed and used with a minimum 20cm distance between the source of radiation and your body. Installing electrical equipment WARNING Do not install business or private equipment if the equipment impedes the driver’s control of the vehicle. ◤ ◢ Caution Bentley Motors does not accept responsibility for non- approved equipment. Before installing equipment, contact an approved Bentley retailer. Do not modify the electrical system when fitting equipment. If the electrical system requires modification, contact an approved Bentley retailer. Bentley Motors does not take responsibility for damage caused by un-approved equipment installation. Electrical equipment that has been installed incorrectly can cause other vehicle systems to fail. vi Important Information

BURY GmbH & Co. KG ▪ Robert-Koch-Straße 1-7 ▪ 32584 Löhne BURY GmbH & Co. KG Robert-Koch-Straße 1-7 32584 Löhne E-Mail [email protected] Internet www.bury.com Sitz der Gesellschaft/Registered office: Robert-Koch-Straße 1-7 D-32584 Löhne Bankverbindungen/Bank Account: Volksbank Schnathorst EG IBAN: EUR DE95 4926 2364 0025 9389 00 USD DE41 4926 2364 0025 9389 02 BIC: GENODEM1SNA Sparkasse Herford IBAN: EUR DE60 4945 0120 0000 0007 78 BIC: WLAHDE44XXX Registergericht/Registration Office: Bad Oeynhausen HRA 2281 Komplementärin/General Partner: BURY Verwaltungsgesellschaft mbH Bad Oeynhausen HRB 2948 Geschäftsführer/General Manager: Dipl.-Ing. Henryk Bury Gerichtsstand/place of jurisdiction: Bad Oeynhausen FB: CM / Stand 27.01.2021 / Rev.: 11 1 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2023-05-05 Ref: Attestation Statement Part 2.911(d)(7) Filing FCC ID:UNLIMITED MODELS BURY GmbH & Co. KG certifies that, as of the dates of this application, Americas Compliance Consulting LLC dba iCertifi “iCertifi” is our designated U.S. agent for service of process for the above referenced FCC ID. BURY GmbH & CO. KG accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission-related proceeding involving the equipment. iCertifi accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service process for the above referenced FCC ID. Designated U.S. Agent Information: Name: Americas Compliance consulting, LLC dba iCertifi FCC FRN: 0033399411 Address: 1001 SW Disk Drive, Suite 250, Bend, Oregon 97702 Contact Person: Paul Preston Tel: 866-885-4575 Email: [email protected] Sincerely, BURY GmbH & Co. KG Americas Compliance Consulting LLC dba iCertifi Johann Dshus Paul Preston Signature

Annex A 1-5116/22-01-01_AnnexA External photos of the Equipment Under Test This addendum is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Document authorized: Michael Dorongovski Lab Manager Radio Labs CTC advanced GmbHUntertuerkheimer Str. 6-10 66117 Saarbruecken / Germany Phone: +49 681 5 98 - 0 Fax: +49 681 5 98 - 9075 web: ctcadvanced.com e-mail: [email protected] Photos Photo 1 Photo 2 2023-01-30Document No. 1-5116/22-01-01_AnnexA2/5 Photo 3 Photo 4 2023-01-30Document No. 1-5116/22-01-01_AnnexA3/5 Photo 5 Photo 6 2023-01-30Document No. 1-5116/22-01-01_AnnexA4/5 Document history VersionApplied changesDate of release initial release2023-01-30 - END OF DOCUMENT - 2023-01-30Document No. 1-5116/22-01-01_AnnexA5/5

Scale 1:1 1/2 Approved by: C. Orzech Designed by: M. Mosiołek Scale: 1:1 Drawing number: Part name and number: Sheet: F DR - 238 A Part version Date Changed by Changes description Part version: 00 Marking method: printed 7_2291 01.1527.000.00 M0855_44 CarGate for TSR 3 3SE 035 008 C 00 M. Mosiołek First release. 25.01 2023 XXXX XXX HBM DD.MM.YY M/N:Car Gate (CG3) S/N:00000000000000000000 HBM-XXXDD.MM.YY00000000 CG3 Bury Sp. z o.o. ul. Wojska Polskiego 4 39-300 Mielec, Poland 3SE 035 008 C FCC ID: QZ9-CG3 IC: 5927A-CG3 CMIIT ID: xxxxxxxxxx 10 R - xxxxxx E1 TA-xxxx-xxxx XXX-XXXXXX X XX-XXXX XXX R T XXXX-XXX- XXX-XXX UA.TR.XXX XXXXXXXXXXXXXX IFETEL: XXXXXXXXX-XXXX NOM Scale 1:1 50 mm 25 mm Print on label 03-1594-0.00_LF 50x25 100 mm 50 mm Scale 2:1 2/2 Approved by: C. Orzech Designed by: M. Mosiołek Scale: 1:1 Drawing number: Part name and number: Sheet: F DR - 238 A Part version Date Changed by Changes description Part version: 00 Marking method: printed 7_2291 01.1527.000.00 M0855_44 CarGate for TSR 3 3SE 035 008 C 00 M. Mosiołek First release. 25.01 2023 XXXX XXX HBM DD.MM.YY M/N:Car Gate (CG3) S/N:00000000000000000000 HBM-XXXDD.MM.YY00000000 CG3 Bury Sp. z o.o. ul. Wojska Polskiego 4 39-300 Mielec, Poland 3SE 035 008 C FCC ID: QZ9-CG3 IC: 5927A-CG3 CMIIT ID: xxxxxxxxxx 10 R - xxxxxx E1 TA-xxxx-xxxx XXX-XXXXXX X XX-XXXX XXX R T XXXX-XXX- XXX-XXX UA.TR.XXX XXXXXXXXXXXXXX IFETEL: XXXXXXXXX-XXXX NOM XXXX XXX HBM DD.MM.YY M/N:Car Gate (CG3) S/N:00000000000000000000 HBM-XXXDD.MM.YY00000000 CG3 Bury Sp. z o.o. ul. Wojska Polskiego 4 39-300 Mielec, Poland 3SE 035 008 C FCC ID: QZ9-CG3 IC: 5927A-CG3 CMIIT ID: xxxxxxxxxx 10 R - xxxxxx E1 TA-xxxx-xxxx XXX-XXXXXX X XX-XXXX XXX R T XXXX-XXX- XXX-XXX UA.TR.XXX XXXXXXXXXXXXXX IFETEL: XXXXXXXXX-XXXX NOM Certification list: 1. EU 2. Great Britain 3. Russia 4. USA 5. Canada 6. China 7. Mexico 8. South Africa 9. Taiwan 10. South Korea 11. Ukraine 12. E-mark 13. Japan 1 2 3 4 5 6 7 8 13 10 11 12 9 7

This document has to be treated confidentially. Its contents are not to be passed on, duplicated, exploited or disclosed without our express permission. All rights reserved, especially the right to apply for protective rights. This document may contain confidential information. If you are not the addressee you are not authorized to make use of the information contained in this document. Please inform us immediately that you have received it by mistake. 1 E xternal Pictures Product (Model Name): Car Gate (CG3) This document has to be treated confidentially. Its contents are not to be passed on, duplicated, exploited or disclosed without our express permission. All rights reserved, especially the right to apply for protective rights. This document may contain confidential information. If you are not the addressee you are not authorized to make use of the information contained in this document. Please inform us immediately that you have received it by mistake. 2 This document has to be treated confidentially. Its contents are not to be passed on, duplicated, exploited or disclosed without our express permission. All rights reserved, especially the right to apply for protective rights. This document may contain confidential information. If you are not the addressee you are not authorized to make use of the information contained in this document. Please inform us immediately that you have received it by mistake. 3 This document has to be treated confidentially. Its contents are not to be passed on, duplicated, exploited or disclosed without our express permission. All rights reserved, especially the right to apply for protective rights. This document may contain confidential information. If you are not the addressee you are not authorized to make use of the information contained in this document. Please inform us immediately that you have received it by mistake. 4 This document has to be treated confidentially. Its contents are not to be passed on, duplicated, exploited or disclosed without our express permission. All rights reserved, especially the right to apply for protective rights. This document may contain confidential information. If you are not the addressee you are not authorized to make use of the information contained in this document. Please inform us immediately that you have received it by mistake. 5

Annex B 1-5116/22-01-01_AnnexB Internal photos of the Equipment Under Test This addendum is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Document authorized: Andreas Curette Testing Manager Radio Communications CTC advanced GmbHUntertuerkheimer Str. 6-10 66117 Saarbruecken / Germany Phone: +49 681 5 98 - 0 Fax: +49 681 5 98 - 9075 web: ctcadvanced.com e-mail: [email protected] Photos Photo 1 Photo 2 2023-02-27Document No. 1-5116/22-01-01_AnnexB2/6 Photo 3 Photo 4 2023-02-27Document No. 1-5116/22-01-01_AnnexB3/6 Photo 5 Photo 6 2023-02-27Document No. 1-5116/22-01-01_AnnexB4/6 Photo 7 2023-02-27Document No. 1-5116/22-01-01_AnnexB5/6 Document history VersionApplied changesDate of release initial release2023-02-27 - END OF DOCUMENT - 2023-02-27Document No. 1-5116/22-01-01_AnnexB6/6

SAR Test exclusion documentation according to CFR 47 §1.1307 Report identification number: 1-5116/22-01-11-A Exemption / MPE (FCC) contains the module with the following certification numbers FCC ID QZ9-CG3 This test report is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Document authorised: Alexander Hnatovskiy Marco Scigliano Lab Manager Testing Manager Radio Communications & EMC Radio Communications & EMC Document History: Version Applied Changes Date of Release Initial Release 2023-03-02 -A Editorial corrections on page 2. 2023-03-20 Test report no.: 1-5116/22-01-11-A © cetecom advanced GmbH Page 2 of 2 EUT technologies: Technologies: Max. meas. cond. AVG Power Max. declared antenna gain Max. EIRP for RF exposure Max. ERP for RF exposure BT EDR 2450 MHz 5.0 dBm 1) < 5.0 dBi 10.0 dBm 7.85 dBm (= 6.10mW) 1) Test result taken from CTC advanced GmbH report 1-5116/22-01-03. Declared minimum safety distance: 19.72cm According the CADs and technical descriptions from the manufacturer a safety distance of 19.72 cm shall be applied between the user (and/or bystanders) to the EUT antenna whilst active transmitting. SAR-Based Exemption following 47 CFR 1.1307 amendment: The SAR-based exemption formula of § 1.1307(b)(3)(i)(B), repeated here as Formula (B.2), applies for single fixed, mobile, and portable RF sources with available maximum time-averaged power or effective radiated power (ERP), whichever is greater, of less than or equal to the threshold P th (mW). This method shall only be used at separation distances from 0.5 cm to 40 cm and at frequencies from 0.3 GHz to 6 GHz (inclusive). P th is given by Formula (B.2). P th ( mW ) ={ ERP 20cm ( d 20cm ) x d≤20cm ERP 20cm 20cm≤ d≤40cm (B.2) where x = - log 10 ( 60 ERP 20cm √ f ) and f is in GHz, d is the separation distance (cm), and ERP 20cm is per Formula (B.1). P th ( mW ) =ERP 20cm ( mW ) ={ ERP 20cm ( d 20cm ) x d≤20cm ERP 20cm 20cm≤ d≤40cm (B.1) Transmitter frequency Max. decl. ERP Minimal Safety Distance (MHz) (mW) (mW) (dBm) (mm) BT EDR 2450 6.10 3060.00 34.8 197.2 EXEMPTED Treshold ERP Verdict Technology

TEST REPORT Test report no.: 1-5116_22-01-0 3 Testing laboratory Applicant CTC advanced GmbH Untertuerkheimer Strasse 6 – 10 66117 Saarbruecken / Germany Phone: + 49 681 5 98 - 0 Fax: + 49 681 5 98 - 9075 Internet: https://www.ctcadvanced.com e-mail: [email protected] Accredited Testing Laboratory: The testing laboratory (area of testing) is accredited according to DIN EN ISO/IEC 17025 (2018-03) by the Deutsche Akkreditierungsstelle GmbH (DAkkS) The accreditation is valid for the scope of testing procedures as stated in the accreditation certificate starting with the registration number: D-PL-12076-01. BURY Sp. z o.o. ul. Wojska Polskiego 4 PL-39-300 Mielec / POLAND Phone: +48 017 788 46 00 Contact: Wojciech Pazdro e-mail: [email protected] Manufacturer BURY Sp. z o.o. ul. Wojska Polskiego 4 PL-39-300 Mielec / POLAND Test standard/s FCC - Title 47 CFR Part 15 FCC - Title 47 of the Code of Federal Regulations; Chapter I; Part 15 - Radio frequency devices RSS - 247 Issue 2 Digital Transmission Systems (DTSs), Frequency Hopping Systems (FHSs) and Licence - Exempt Local Area Network (LE-LAN) Devices For further applied test standards please refer to section 3 of this test report. Test Item Kind of test item: Base Station Model name: Car Gate (CG3) FCC ID: QZ9-CG3 ISED certification number: 5927A-CG3 Frequency: 2400 MHz to 2483.5 MHz Technology tested: Bluetooth ® + EDR Antenna: Inverted F antenna Power supply: 12.0 V DC by vehicle battery Temperature range: -40°C to +85°C This test report is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Test report authorized: Test performed: Marco Bertolino Michael Dorongovski Lab Manager Lab Manager Radio Communications Radio Communications Test report no.: 1-5116_22-01-03 © CTC advanced GmbH Page 2 of 47 1 Table of contents 1 Table of contents ............................................................................................................................................. 2 2 General information ......................................................................................................................................... 4 2.1 Notes and disclaimer ............................................................................................................................ 4 2.2 Application details ................................................................................................................................ 4 2.3 Test laboratories sub-contracted ......................................................................................................... 4 3 Test standard/s, references and accreditations .............................................................................................. 5 4 Reporting statements of conformity – decision rule ...................................................................................... 6 5 Test environment ............................................................................................................................................. 7 6 Test item........................................................................................................................................................... 7 6.1 General description ............................................................................................................................... 7 6.2 Additional information .......................................................................................................................... 7 7 Sequence of testing ......................................................................................................................................... 8 7.1 Sequence of testing radiated spurious 9 kHz to 30 MHz ..................................................................... 8 7.2 Sequence of testing radiated spurious 30 MHz to 1 GHz .................................................................... 9 7.3 Sequence of testing radiated spurious 1 GHz to 18 GHz ................................................................... 10 7.4 Sequence of testing radiated spurious above 18 GHz ....................................................................... 11 8 Description of the test setup .......................................................................................................................... 12 8.1 Shielded semi anechoic chamber ....................................................................................................... 13 8.2 Shielded fully anechoic chamber ........................................................................................................ 14 8.3 Radiated measurements > 18 GHz...................................................................................................... 15 8.4 Conducted measurements Bluetooth system .................................................................................... 16 9 Measurement uncertainty .............................................................................................................................. 17 10 Summary of measurement results ......................................................................................................... 18 11 Additional comments .............................................................................................................................. 19 12 Measurement results .............................................................................................................................. 20 12.1 Antenna gain .................................................................................................................................... 20 12.2 Carrier frequency separation ........................................................................................................... 21 12.3 Number of hopping channels ...........................................…

Text truncated - open the document above for the full version.

Measurement Results No.1-5116/22-01-03_Annex_MR_A1 Log file - conducted results This document is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Test/s performed: Michael Dorongovski Lab Manager Radio Communications CTC advanced GmbHUntertuerkheimer Str. 6-10 66117 Saarbruecken / Germany Phone: +49 681 5 98 - 0 Fax: +49 681 5 98 - 9075 web: ctcadvanced.com e-mail: [email protected] Table of Content EUT Information3 Common 2G4 # Peak output power 3MHz/3MHz ~ BT Classic Basic rate4 FCC 15.247 # Maximum peak conducted output power FHSS ~ BT Classic Basic rate8 FCC 15.247 # Maximum peak conducted output power FHSS ~ BT Classic EDR Pi/4DQPSK12 FCC 15.247 # Maximum peak conducted output power FHSS ~ BT Classic EDR 8DPSK16 FCC 15.247, ISED RSS247 # Bandwidth 99PCT and 20dB ~ BT Classic Basic rate20 FCC 15.247, ISED RSS247 # Bandwidth 99PCT and 20dB ~ BT Classic EDR Pi/4DQPSK30 FCC 15.247, ISED RSS247 # Bandwidth 99PCT and 20dB ~ BT Classic EDR 8DPSK40 FCC 15.247 # Carrier frequency separation FHSS ~ BT Classic Basic rate50 FCC 15.247 # Number of hopping channels FHSS ~ BT Classic Basic rate53 FCC 15.247 # TX spurious conducted 20dBc ~ BT Classic Basic rate58 FCC 15.247 # TX spurious conducted 20dBc ~ BT Classic EDR Pi/4DQPSK65 FCC 15.247 # TX spurious conducted 20dBc ~ BT Classic EDR 8DPSK72 2022-11-23Document 1-5116/22-01-03_Annex_MR_A12/78 EUT Information EUT DEFINITION ManufacturerBURY Sp. z o.o. TypeCar Gate (CG3) Serial NumberConducted sample 3 Setup Number1.0 Version SWX600 Version FWNI Version HWH04 Comment 1 Comment 2 Temperature [°C] Min-40 Temperature [°C] Nom20 Temperature [°C] Max85 Voltage [V] Min6 Voltage [V] Nom12 Voltage [V] Max16 2022-11-23Document 1-5116/22-01-03_Annex_MR_A13/78 Common 2G4 # Peak output power 3MHz/3MHz ~ BT Classic Basic rate Test References TC Start14.11.2022 16:24:32 Ambit Temp [°C] | Humidity [rel%] 26.1 | 34 System Version3.3.1.8 Test SpecificationCommon 2G4 - none Test Method TC Version0.0.1 My DescriptionPeak Output Power conducted 3MHz/3MHz - BT Classic Basic Rate Add. Information EUT Common Settings BT Classic Intermodulation Value N3 Image Freq. Low | Mid | High [MHz]0 | 0 | 0 Power Class1 Power ControlNo Longest Supported Packet TypeDH5 RF SupportedBasic Rate True | EDR Pi/4DQPSK True | EDR 8DPSK True Testmode LOOPback Perform InquiryYes EUT BT Address (if Inqiury No)0123456789AB Signaling BT AddressBABEBEDADBAD Switch Matrix & Pathcompensation enabledYes Test Parameter Technology to testBT Classic Basic rate Antenna Port used1 Temperaturenom Voltagenom Frequency low to testTrue | Freq [MHz] 2402 Frequency mid to testTrue | Freq [MHz] 2441 Frequency high to testTrue | Freq [MHz] 2480 Auto Control enabled Power Supply | Climatic Box Yes | No Additional Path Loss [dB]0 Switched PathEUT - SignalingUnit - SpectrumAnalyzer Test Equipment Signal analyzer,Rohde&Schwarz,FSV-30,1321.3008K30/103809,3.70 Signaling unit,Rohde&Schwarz,CMW,1201.0002k75/102550,4.0.62 Switch matrix,CTCadvanced,RSM-1 NI DAQ,29655273,NI Power supply,Agilent Technologies,N5767A,US14J1569P,B.00.06,REV:F 2022-11-23Document 1-5116/22-01-03_Annex_MR_A14/78 Test at TX 2402 MHz RESULT: Reference Power cond. Test DescriptionLower LimitUpper LimitMeasuredUnitVerdict Ref. Power 1MHz/1MHz cond. ------3.08dBmINFO Ref. Frequency------2402.200MHzINFO READ SA SETTINGS: RefLevel [dBm] | RefLevelOffset [dB] | InpAtt [dB]13.08 | 10.09 | 20 Start [MHz] | Stop [MHz]2399.500 | 2404.500 RBW [MHz] | VBW [MHz]3.000000 | 3.000000 Detector | TraceModePOS | MAXH Sweep: Time [ms] | Count | Points per Section | Type1000 | 10 | 1001 | SWE RESULT Test DescriptionLower LimitUpper LimitMeasuredUnitVerdict Peak Power------3.19dBmINFO Peak Power------2.084491mWINFO Frequency at Peak------2402.2MHzINFO Common 2G4 # Peak output power 3MHz-3MHz ~ BT Classic Basic rate 2022-11-23Document 1-5116/22-01-03_Annex_MR_A15/78 Test at TX 2441 MHz RESULT: Reference Power cond. Test DescriptionLower LimitUpper LimitMeasuredUnitVerdict Ref. Power 1MHz/1MHz cond. ------2.16dBmINFO Ref. Frequency------2440.800MHzINFO READ SA SETTINGS: RefLevel [dBm] | RefLevelOffset [dB] | InpAtt [dB]12.16 | 10.1 | 20 Start [MHz] | Stop [MHz]2438.500 | 2443.500 RBW [MHz] | VBW [MHz]3.000000 | 3.000000 Detector | TraceModePOS | MAXH Sweep: Time [ms] | Count | Points per Section | Type1000 | 10 | 1001 | SWE RESULT Test DescriptionLower LimitUpper LimitMeasuredUnitVerdict Peak Power------2.32dBmINFO Peak Power------1.706082mWINFO Frequency at Peak------2440.74MHzINFO Common 2G4 # Peak output power 3MHz-3MHz ~ BT Classic Basic rate 2022-11-23Document 1-5116/22-01-03_Annex_MR_A16/78 Test at TX 2480 MHz RESULT: Reference Power cond. Test DescriptionLower LimitUpper LimitMeasuredUnitVerdict Ref. Power 1MHz/1MHz cond. ------1.79dBmINFO Ref. Frequency------2479.800MHzINFO READ SA SETTINGS: RefLevel [dBm] | RefLevelOffset [dB] | InpAtt [dB]11.79 | 10.15 | 20 Start [MHz] | Stop [MHz]2477.500 | 2482.500 RBW [MHz] | VBW [MHz]3.000000 | 3.000000 Detector | TraceModePOS | MAXH Sweep: Time [ms] | Count | Points per Section | Type1000 | 10 | 1001 | SWE RESULT Test DescriptionLower LimitUpper LimitMeasuredUnitVerdict Peak Power------1.9dBmINFO Peak Power------1.548817mWINFO Frequency at Peak------2479.805MHzINFO Common 2G4 # Peak output power 3MHz-3MHz ~ BT Classic Basic rate General verdictPASS 2022-11-23Document 1-5116/22-01-03_Annex_MR_A17/78 FCC 15.247 # Maximum peak conducted output power FHSS ~ BT Classic Basic rate Test References TC Start14.11.2022 17:07:57 Ambit Temp [°C] | Humidity [rel%] 26.0 | 34 System Version3.3.1.8 Test SpecificationFCC 15.247 - Test Method TC Version0.0.1 My DescriptionFCC 15.247 Maximum Peak Output Power Conducted FHSS - BT Classic Basic Rate Add. Information EUT Common Settings BT Classic Intermodulation Value N3 Image Freq. Low | Mid | High [MHz]0 | 0 | 0 Power Class1 Power ControlNo Longest Supported Packet Typ…

Text truncated - open the document above for the full version.

Annex D 1-5116/22-01-01_AnnexD Setup photos of the Equipment Under Test This addendum is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Document authorized: Michael Dorongovski Lab Manager Radio Labs CTC advanced GmbHUntertuerkheimer Str. 6-10 66117 Saarbruecken / Germany Phone: +49 681 5 98 - 0 Fax: +49 681 5 98 - 9075 web: ctcadvanced.com e-mail: [email protected] Photos Photo 1 Photo 2 2023-01-30Document No. 1-5116/22-01-01_AnnexD2/6 Photo 3 Photo 4 2023-01-30Document No. 1-5116/22-01-01_AnnexD3/6 Photo 5 Photo 6 2023-01-30Document No. 1-5116/22-01-01_AnnexD4/6 Photo 7 Photo 8 2023-01-30Document No. 1-5116/22-01-01_AnnexD5/6 Document history VersionApplied changesDate of release initial release2023-01-30 - END OF DOCUMENT - 2023-01-30Document No. 1-5116/22-01-01_AnnexD6/6