R8KUGWSX931900MHz Transceiver Module

ARES/ATHENA UHF Modules Solutions for a Real Time World User Manual RE-TEK-1890 1 45388 Warm Springs Blvd. Fremont, CA 94539 [email protected] TEL: (510) 668.2088 FAX: (510) 661.2788 http://www.unigen.com Toll Free: (800) 826.0808 Copyright Unigen Corporation, 2012 UNIGEN CORP. WIRELESS MODULE PRODUCTS ARES: UGWSX931SM0033U ATHENA: UGWSX933SM0033U Low Power Integrated UHF Transceivers USER MANUAL ARES FCC ID: R8KUGWSX931 ATHENA FCC ID: R8KUGWSX931 ARES IC ID: 5125A-UGWSX931 ATHENA IC ID: 5125A-UGWSX931 Issue Date: 30 September, 2012 Revision: 0.90 Revision History Rev. No. History Issue Date Remarks 0.9 First Release 30 September, 2012 First release ARES/ATHENA Solutions for a Real Time World User Manual RE-TEK-1890 2 45388 Warm Springs Blvd. Fremont, CA 94539 [email protected] TEL: (510) 668.2088 FAX: (510) 661.2788 http://www.unigen.com Toll Free: (800) 826.0808 Copyright Unigen Corporation, 2009 THIS DOCUMENT IS PROVIDED “AS IS” WITH NO WARRANTIES WHATSOEVER, INCLUDING ANY WARRANTY OF MERCHANTABILITY, NON-INFRINGEMENT, FITNESS FOR ANY PARTICULAR PURPOSE, OR ANY WARRANTY OTHERWISE ARISING OUT OF ANY PROPOSAL, SPECIFICATION OR SAMPLE. Unigen Corporation disclaims all liability, including liability for infringement of any proprietary rights, relating to use of information in this document. No license, expressed or implied, by estoppel or otherwise, to any intellectual property rights is granted herein. *Third-party brands, names, and trademarks are the property of their respective owners. ARES/ATHENA Solutions for a Real Time World User Manual RE-TEK-1890 3 45388 Warm Springs Blvd. Fremont, CA 94539 [email protected] TEL: (510) 668.2088 FAX: (510) 661.2788 http://www.unigen.com Toll Free: (800) 826.0808 Copyright Unigen Corporation, 2009 UNIGEN CORP. WIRELESS MODULE PRODUCTS 1 FCC ID: R8KUGWAS82 1 ELIGIBILITY REQUIREMENTS FOR REGULATORY MODULE APPROVAL 5 User Guide Information 6 United States of America Requirements 6 General User Guide Requirements 6 Topics Not Covered 7 UNITED STATES REGULATORY APPROVAL FCC MODULAR APPROVAL (MA) 7 Design Criteria for Modular Approval 7 General Conditions 7 Antennae 7 Antenna Interconnect & Impedance 8 Physical Implementation 8 Emissions Compliance Testing 8 Co-location of Additional Transmitters 8 Product Labeling Requirements 9 INDUSTRY CANADIAN REGULATORY APPROVAL 10 Design Criteria for Modular Approval 10 General Conditions 10 Antennae 10 Antenna Interconnect & Impedance 11 Physical Implementation 11 Emissions Compliance Testing 12 Product Labeling Requirements 12 EUROPEAN UNION REGULATORY APPROVAL 13 Design Criteria for Modular Approval 13 General Conditions 13 Antennae 13 Antenna Interconnect & Impedance 14 Physical Implementation 14 Emissions Compliance Testing 14 ARES/ATHENA Solutions for a Real Time World User Manual RE-TEK-1890 4 45388 Warm Springs Blvd. Fremont, CA 94539 [email protected] TEL: (510) 668.2088 FAX: (510) 661.2788 http://www.unigen.com Toll Free: (800) 826.0808 Copyright Unigen Corporation, 2009 Exterior Labeling Requirements 16 UNITED STATES AND INTERNATIONAL TYPE APPROVAL (STANDARD REGULATORY EQUIPMENT CERTIFICATION) 17 CONTACT INFORMATION 17 APPENDIX A: 18 Agency Certifications: 18 Regulatory Compliance Statement: 18 EUROPEAN UNION “DECLARATION OF CONFORMITY” 19 MECHANICAL CHARACTERISTICS: 19 APPENDIX B: 22 FCC Grant# - R8KUGWSX931 22 ARES/ATHENA Solutions for a Real Time World User Manual RE-TEK-1890 5 45388 Warm Springs Blvd. Fremont, CA 94539 [email protected] TEL: (510) 668.2088 FAX: (510) 661.2788 http://www.unigen.com Toll Free: (800) 826.0808 Copyright Unigen Corporation, 2009 ELIGIBILITY REQUIREMENTS FOR REGULATORY MODULE APPROVAL The Unigen UGWSX933SM0033U WiFi module (the “UGWSX933SM0033U”) marketed under the name APOLLO, is a device that transmits and receives radio signals in accordance with the spectrum regulations for the 2.4-GHz unlicensed frequency range. Regional regulatory agency approval may be required to operate UGWSX933SM0033U throughout the world. For purposes of ease of integration, time to market, and product surety, Unigen submitted UGWSX933SM0033U to relevant agencies and obtained regulatory approvals for specific countries. UGWSX933SM0033U was approved under the “Modular Approval (MA) Grant”. This certification represents a significant cost savings to the OEM. The radio certification portion of this grant is transferable to Digital Electronic Device manufacturers given adherence to specific implementation criteria noted herein. Any modification of the UGWSX933SM0033U will void the manufacturer’s warranty. Any alteration or deviation from the documented installation and/or use of the UGWSX933SM0033U will void the MA Grant as it applies to the end-product. In the event the Digital Electronic Device manufacturer alters the herein described and approved installation of the UGWSX933SM0033U, the end-product may require a complete battery of regulatory agency certification test Digital Electronic Device manufacturer may be required to submit to a complete battery of tests, depending on the requirements noted in the region they wish to sell their product. The MA Grant provides that Digital Electronic Device manufacturers who incorporate UGWSX933SM0033U as tested and approved, and can be relieved from having to perform the Radio Regulatory certification portion of the respective agency certification. The MA Grant is valid only in countries that recognize the MA Grant certification process. Countries currently accepting the MA Grant include; the USA, Canada, and many European countries as noted in the General User Guide Requirements Section of this document. Terms and conditions of regulatory approval for these countries are also described herein. However, this “grandfathered” radio certification does not relieve the Digital Electronic Device manufacturers from submitting their device for digital emissions certifications. Electronic device manufacturers may disregard the requirements of this section pro…

Text truncated - open the document above for the full version.

- AUTHORIZATION - TO WHOM IT MAY CONCERN This is to state that Elliott Laboratories, LLC an NTS Company (NTS Silicon Valley) is hereby authorized to deal in all technical and regulatory matters pertaining to approval of: Product Name: Area/Athena Model Number: UGWSX931SM0033U/ UGWSX933SM0033U We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Sincerely, Date: Sep 24 2012 By: Weerapol Seesanung Signature Printed Name Title: Wireless Validation ENgineer Tel.No: 510-6682088 Date Sep 24, 2012 NTS Silicon Valley 41039 Boyce Road Fremont, CA. 94538 In reference to the application under FCC ID: R8KUGWANBL2, and pursuant to Sections 0.457(d)1(ii) and 0.459 of the Commission’s Rules, The Applicant hereby requests confidential treatment of the accompanying information as outlined below: Block Diagram Schematics Theory of Operations The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to The Applicant and provide unjustified benefits to its competitors. In addition to the above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the important rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short term confidentiality on the following attachments until 30 Nov 2012 External Photos Internal Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondence during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Weerapol Seesanung Wireless Validation Engineer Sep 24, 2012 Certification and Engineering Bureau Industry Canada P.O. Box 11490, Station H 3701 Carling Avenue (Building 94) Ottawa, Ontario K2H 8S2 Subject: Confidentiality request for IC: 5125A-UGWANBL2 To Whom It May Concern, Pursuant to sections RSP-100, Section 10, the applicant requests confidential treatment of the following information accompanying this application: Block Diagrams Schematics Theory of Operations The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. Sincerely, Weerapol Seesanung Wireless Validation Engineer Acknowledgement of IC Listing Requirements By signing this document, we acknowledge that any information specified on the ETCB Application and Agreement Form for Industry Canada Certification Services provided with this application may be provided to Industry Canada. We acknowledge that this information may be posted in the Radio Equipment List (REL) on the Department's Web Site. Additionally, we understand that we must inform ETCB of any changes to the information submitted. We further acknowledge that the Certified product shall not be distributed, leased, or offered for sale in Canada prior to its listing on the Industry Canada Radio Equipment List (REL). We are aware that we may verify the status of this listing at the following web address: http://strategis.ic.gc.ca/cgi-bin/sc_mrksv/spectrum/reltelSearch/search.pl?lang=e&db=rel Dated this Sep24 , 2012 By: Weerapol Seesanung Title: Wireless Validation Engineer email: [email protected] On behalf of: Unigen Corporation Telephone: 5106682088 CANADIAN REPRESENTATIVE LETTER OF ATTESTATION (Multiple Certifications or Registrations sample letter) Canadian Representative Company Name: 3874A CN Number: Celltech Labs Inc. Contact Name: Ben Hewson Street Address: 21-364 Lougheed Road City/Province/Zip: Kelowna, BC V1X 7R8 Telephone No: (250) 765-7650 ext. 201 Fax No: (250) 765-7645 Email: [email protected] TO: Industry Canada 3701 Carling Ave., Bldg. 94, Ottawa, ON, K2H 8S2 ATTENTION: Certification and Engineering Bureau This letter is to confirm that we have accepted the responsibility to act as Canadian Representative on behalf of the Applicant noted below for all future Industry Canada certification/registrations obtained during the period of this agreement which ends at the specified date below (if applicable). As Canadian Representative, we are aware of the requirements involved as outlined in Industry Canada applicable documents (RSP-100, Section 3.4 and/or DC-01, Section 7.2). Applicant IC Company No.: 5125A Company Name: Unigen Corporation Address: 45388 Warm Springs Blvd. Fremont, CA 94539 United States Contact Name: Weerapool Seesanung Telephone No.: 510-668-2088 Fax No.: 510-661-4889 Email: [email protected] This Attestation is valid until: August 31, 2014 Ben Hewson President Celltech Labs Inc. SN: CLI-2012-0901-AN

- AUTHORIZATION - TO WHOM IT MAY CONCERN This is to state that Elliott Laboratories, LLC an NTS Company (NTS Silicon Valley) is hereby authorized to deal in all technical and regulatory matters pertaining to approval of: Product Name: Area/Athena Model Number: UGWSX931SM0033U/ UGWSX933SM0033U We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Sincerely, Date: Sep 24 2012 By: Weerapol Seesanung Signature Printed Name Title: Wireless Validation ENgineer Tel.No: 510-6682088 Date Sep 24, 2012 NTS Silicon Valley 41039 Boyce Road Fremont, CA. 94538 In reference to the application under FCC ID: R8KUGWANBL2, and pursuant to Sections 0.457(d)1(ii) and 0.459 of the Commission’s Rules, The Applicant hereby requests confidential treatment of the accompanying information as outlined below: Block Diagram Schematics Theory of Operations The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to The Applicant and provide unjustified benefits to its competitors. In addition to the above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the important rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short term confidentiality on the following attachments until 30 Nov 2012 External Photos Internal Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondence during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Weerapol Seesanung Wireless Validation Engineer Sep 24, 2012 Certification and Engineering Bureau Industry Canada P.O. Box 11490, Station H 3701 Carling Avenue (Building 94) Ottawa, Ontario K2H 8S2 Subject: Confidentiality request for IC: 5125A-UGWANBL2 To Whom It May Concern, Pursuant to sections RSP-100, Section 10, the applicant requests confidential treatment of the following information accompanying this application: Block Diagrams Schematics Theory of Operations The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. Sincerely, Weerapol Seesanung Wireless Validation Engineer Acknowledgement of IC Listing Requirements By signing this document, we acknowledge that any information specified on the ETCB Application and Agreement Form for Industry Canada Certification Services provided with this application may be provided to Industry Canada. We acknowledge that this information may be posted in the Radio Equipment List (REL) on the Department's Web Site. Additionally, we understand that we must inform ETCB of any changes to the information submitted. We further acknowledge that the Certified product shall not be distributed, leased, or offered for sale in Canada prior to its listing on the Industry Canada Radio Equipment List (REL). We are aware that we may verify the status of this listing at the following web address: http://strategis.ic.gc.ca/cgi-bin/sc_mrksv/spectrum/reltelSearch/search.pl?lang=e&db=rel Dated this Sep24 , 2012 By: Weerapol Seesanung Title: Wireless Validation Engineer email: [email protected] On behalf of: Unigen Corporation Telephone: 5106682088 CANADIAN REPRESENTATIVE LETTER OF ATTESTATION (Multiple Certifications or Registrations sample letter) Canadian Representative Company Name: 3874A CN Number: Celltech Labs Inc. Contact Name: Ben Hewson Street Address: 21-364 Lougheed Road City/Province/Zip: Kelowna, BC V1X 7R8 Telephone No: (250) 765-7650 ext. 201 Fax No: (250) 765-7645 Email: [email protected] TO: Industry Canada 3701 Carling Ave., Bldg. 94, Ottawa, ON, K2H 8S2 ATTENTION: Certification and Engineering Bureau This letter is to confirm that we have accepted the responsibility to act as Canadian Representative on behalf of the Applicant noted below for all future Industry Canada certification/registrations obtained during the period of this agreement which ends at the specified date below (if applicable). As Canadian Representative, we are aware of the requirements involved as outlined in Industry Canada applicable documents (RSP-100, Section 3.4 and/or DC-01, Section 7.2). Applicant IC Company No.: 5125A Company Name: Unigen Corporation Address: 45388 Warm Springs Blvd. Fremont, CA 94539 United States Contact Name: Weerapool Seesanung Telephone No.: 510-668-2088 Fax No.: 510-661-4889 Email: [email protected] This Attestation is valid until: August 31, 2014 Ben Hewson President Celltech Labs Inc. SN: CLI-2012-0901-AN

Limited Modular Approval is being requested for this device. The following paragraphs detail the requirements for modules and explain how the module meets those requirements. Where requirements are not met a justification for a limited modular approval is presented. FCC §15.212 Requirements for Single Modular Transmitters (includes RSS GEN Section 3.2.2) (a) Single modular transmitters consist of a completely self-contained radiofrequency transmitter device that is typically incorporated into another product, host or device. Split modular transmitters consist of two components: a radio front end with antenna (or radio devices) and a transmitter control element (or specific hardware on which the software that controls the radio operation resides). All single or split modular transmitters are approved with an antenna. All of the following requirements apply, except as provided in paragraph (b) of this section. (1) Single modular transmitters must meet the following requirements to obtain a modular transmitter approval. (i) The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The module contains a shield (metal sheet that cover top of product). (ii) The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with part 15 requirements under conditions of excessive data rates or over-modulation. Data to the modulation circuit is buffered on the module via SMT pad as J2 (iii) The modular transmitter must have its own power supply regulation. The module does not contain its own power supply regulation as it relies on the host system. The regulator for the host system is manufactured by Torex, part number XC6204B302MR and is a 3.0V fixed regulator SOT23-5 package. (iv) The modular transmitter must comply with the antenna and transmission system requirements of §§15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of §15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. The module connects to its antenna via Mini coax connector. This connector is a non- standard connector. The coax antenna with 0.8dBi gain Installation instructions for the module explain that only these antennas may be used with the device and that the end user shall not be able to access the antenna port or change antennas. (v) The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in §15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see §15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see §15.31(i)). Test data contained in this application is for the device tested in a stand-alone configuration. Radiated spurious emissions data and AC conducted emissions data demonstrating compliance with the requirements of Part 15 of the FCC rules for intentional radiators and RSS GEN/RSS 210 has been provided. (vi) The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. (A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. (B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC certified transmitter module(s).” Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. The module is appropriately labeled (refer to the label and label location drawings contained within this application). Instructions to the end user regarding the labeling requirements for host devices are included in this application. (vii) The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufa…

Text truncated - open the document above for the full version.

EMC Test Data Client: Contact: Standard: Test Specific Details General Test Configuration Yes Unigen CorporationJob Number: J88443 Model: ARES / ATHENA T-Log Number: T88506 Account Manager: Christine Krebill Weerapol Seesanung FCC 15.247/RSS-210Class: N/A Summary of Results Maximum Permissible Exposure Objective: The objective of this test session is to perform final qualification testing of the EUT with respect to the specification listed above. Date of Test: 8/6/2012 Device complies with Power Density requirements at 20cm separation: Test Engineer: Mark Hill Calculation uses the free space transmission formula: S = (PG)/(4 πd 2 ) Where: S is power density (W/m 2 ), P is output power (W), G is antenna gain relative to isotropic, d is separation distance from the transmitting antenna (m). 20cm separation: Modifications Made During Testing No modifications were made to the EUT during testing Deviations From The Standard No deviations were made from the requirements of the standard. T88506.xlsMPE CalcPage 1 of 2 EMC Test Data Client: Contact: Standard: Unigen CorporationJob Number: J88443 Model: ARES / ATHENA T-Log Number: T88506 Account Manager: Christine Krebill Weerapol Seesanung FCC 15.247/RSS-210Class: N/A Use: General Antenna:3.0dBi USE THIS FOR 300-1500 MHz sin gle transmitters Cable AntPower Freq.LossGainat AntEIRP MHzdBmmW*dBdBidBmmW 90314.528.20314.556.23 91514.628.80314.657.54 92714.729.50314.758.88 For the cases where S > the MPE Limit Fre q. MHz 903 915 927 EUTPower Densit y (S)MPE Limit Powe rat 20 cmat 20 cm mW/cm^2mW/cm^2 0.0110.602 0.0110.610 mW/cm^2mW/cm^2cm 0.0120.618 Power Densit y MPE LimitDistance where 0.0110.6102.7 at 20 cmat 20 cmS <= MPE Limit 0.0120.6182.8 0.0110.6022.7 T88506.xlsMPE CalcPage 2 of 2

File: R88716 Page 1 EMC Test Report Application for Grant of Equipment Authorization Industry Canada RSS-Gen Issue 3 / RSS 210 Issue 8 FCC Part 15 Subpart C ARES / ATHENA Model UGWSX931SM0033U and UGWSX933SM0033U IC CERTIFICATION #: 5125A-UGWSX931 FCC ID: R8KUGWSX931 APPLICANT: Unigen Corporation 45388 Warm Springs Blvd. Fremont, CA 94539 TEST SITE(S): NTS Silicon Valley 41039 Boyce Road. Fremont, CA. 94538-2435 IC SITE REGISTRATION #: 2845B-3; 2845B-4 REPORT DATE: October 5, 2012 FINAL TEST DATES: July 24 and 25, 2012 TOTAL NUMBER OF PAGES: 49 PROGRAM MGR / QUALITY ASSURANCE DELEGATE / TECHNICAL REVIEWER: FINAL REPORT PREPARER: ______________________________ ______________________________ Mark E Hill David Guidotti Staff Engineer Senior Technical Writer NTS Silicon Valley is accredited by the A2LA, certificate number 0214.26, to perform the test(s) listed in this report, except where noted otherwise. This report and the information contained herein represent the results of testing test articles identified and selected by the client performed to specifications and/or procedures selected by the client. National Technical Systems (NTS) makes no representations, expressed or implied, that such testing is adequate (or inadequate) to demonstrate efficiency, performance, reliability, or any other characteristic of the articles being tested, or similar products. This report should not be relied upon as an endorsement or certification by NTS of the equipment tested, nor does it represent any statement whatsoever as to its merchantability or fitness of the test article, or similar products, for a particular purpose. This report shall not be reproduced except in full NTS Silicon Valley -- EMC Department Test Report Report Date: October 5, 2012 File: R88716 Page 2 REVISION HISTORY Rev# Date Comments Modified By - 10/5/2012 First release NTS Silicon Valley -- EMC Department Test Report Report Date: October 5, 2012 File: R88716 Page 3 TABLE OF CONTENTS REVISION HISTORY ................................................................................................................................................ 2 TABLE OF CONTENTS ............................................................................................................................................ 3 SCOPE .......................................................................................................................................................................... 4 OBJECTIVE ................................................................................................................................................................ 4 STATEMENT OF COMPLIANCE ........................................................................................................................... 5 DEVIATIONS FROM THE STANDARDS .............................................................................................................. 5 TEST RESULTS SUMMARY ................................................................................................................................... 6 DIGITAL TRANSMISSION SYSTEMS ( 902 – 928 MHZ) ................................................................................... 6 GENERAL REQUIREMENTS APPLICABLE TO ALL BANDS .......................................................................... 6 MEASUREMENT UNCERTAINTIES .................................................................................................................... 7 EQUIPMENT UNDER TEST (EUT) DETAILS ...................................................................................................... 8 GENERAL ................................................................................................................................................................ 8 OTHER EUT DETAILS ........................................................................................................................................... 8 ANTENNA SYSTEM .............................................................................................................................................. 8 ENCLOSURE ........................................................................................................................................................... 8 MODIFICATIONS ................................................................................................................................................... 8 SUPPORT EQUIPMENT ......................................................................................................................................... 9 EUT INTERFACE PORTS ...................................................................................................................................... 9 EUT OPERATION ................................................................................................................................................... 9 TEST SITE ................................................................................................................................................................. 10 GENERAL INFORMATION ................................................................................................................................. 10 CONDUCTED EMISSIONS CONSIDERATIONS ........................................................................…

Text truncated - open the document above for the full version.