RC6AWU-901WWireless USB Adapter

W W i i r r e e l l e e s s s s P P o o c c k k e e t t U U S S B B User Manual Rev. 1.1 April 2004 1 User Manual for the Wireless Pocket USB FCC Information to User FCC Caution To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Guidelines for Human Exposure This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This EUT is incompliance with SAR for general population /uncontrolled exposure limits in ANSI/IEEE C95.1-1999 and had been tested in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C. Regulatory Compliance Information This section includes user requirements for operating this product in accordance with National laws for usage of radio spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may result in unlawful operation and adverse action against the end-user by the applicable National regulatory authority. FCC Requirements for Operation in the United States Radio Frequency Interference Warnings & Instructions This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following methods: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and the receiver • Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is connect Model: Wireless Pocket USB FCC ID: RC6AWU-901W 2 User Manual for the Wireless Pocket USB • Consult the dealer or an experienced radio/TV technician for help. Modifications made to the product could void the user's right to operate the equipment. Europe - EU Declaration of Conformity Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards: EN300 328, EN301 489-1/17, EN60950 Requirements For Operation in the European Community Countries of Operation and Conditions of Use in the European Community The user should run the utility program provided with this product to check the current channel of operation and confirm that the device is operating in conformance with the spectrum usage rules for European Community countries as described in this section. This device is intended to be operated in all countries of the European Community. Operation Using 2.4 GHz Channels in France The following radio channel usage limitations apply in France. The radio spectrum regulator in France, Autorité de regulation des telecommunications (ART), enforces the following rules with respect to use of 2.4GHz spectrum in various locations in France. Please check ART's web site for latest requirements for use of the 2.4GHz band in France: http://www.art-telecom.fr/eng/index.htm. When operating in the following metropolitan regions (départements) in France, this device may be operated under the following conditions: • Indoors using any channel in the 2.4-2.4835 GHz band (Channels 1-13) • Outdoors using channels in the 2.4-2.454 GHz band (Channels 1-7) When operating outside of the following regions (départements) in France such as Guadeloupe, Martinique, St Pierre et Miquelon, Mayotte, this product can be operated under the following conditions: • Indoors using any channel in the 2.4-2.4835 GHz band (Channels 1-13) • Outdoors using any channel in the 2.4-2.4835 GHz band (Channels 1-13) When operating outside of the following regions (départements) in France such as Réunion and Guyana, this product can be operated under the following conditions: • Indoors using any channel in the 2.4-2.4835 GHz band (Channels 1-13) • Outdoors using channels in the 2.420-2.4835 GHz band (Channels 3-13) This device is a 2.4 GHz low power RF device intended for home and office use in EU and EFTA member states. In some EU / EFTA member states some restrictions may apply. Please contact local spectrum management authorities for further details before putting this device into operation. 0678 3 User Manual for the Wireless Pocket USB Please refer to the ART web site for further details. Metropolitan Regions: 4 User Manual for the Wireless Pocket USB Table of Contents Chapter 1 Introduction ............................................................................................................... 6 1.1 Preface ............................................................................................................... 6 1.2 Key Features...................................................................................................... 6 1.3 Kit Contents........................................................................................................ 6 1.4 System Requirements ........................................................................................ 6 1.5 LED Definition .........................................................…

Text truncated - open the document above for the full version.

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 April 30, 2004 RE: Amigo Technology Co., Ltd. FCC ID: RC6AWU-901W I have a few comments on the above referenced Application. General Requirements 1) Is an agency letter available for this application? 2) It appears that some of the data may have been reported incorrectly on page 16. Please correct. 3) Since this device may be considered as a PC Peripheral, then an compliance information sheet should be included in the manual on the same page as the FCC statements (alternatively, this may be shipped with the product as a separate sheet). Please provide. This information should contain the following information regarding DoC compliance: COMPLIANCE INFORMATION (47CFR 2.1077) If a product is tested and authorized under a Declaration of Conformity, a compliance information statement shall be supplied with the product at the time of marketing or importation, containing the following information: (1) Identification of the product, i.e. name and model number. (NOTE THIS IS ALREADY IN THE MANUAL) (2) A statement similar to that contained in Section 15.19(a)(3) that the product complies with Part 15 of the regulations. (NOTE THIS IS ALREADY IN THE MANUAL) (3) The identification, by name, address and telephone number, of the responsible party. The responsible party is defined as either the manufacturer, or if the equipment is imported, the importer. The responsible party for a Declaration of Conformity must be located within the United States. (THIS IS MISSING ON PAGE 2). 4) The RF exposure statement in the users manual references 20 cm. Please note that 20 cm is not considered an applicable distance since PCMCIA cards positioned in the laptop are closer than this when positioned in the lap. Please correct the RF exposure information in the manual. 5) The SAR report provided is blank after the first 7 pages. Please provide again. Timothy R. Johnson Examining Engineer mailto: [email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

Hi, Tim, 1) No, we don't have. Normally, the signed back quotation form is the POA recognized by our client 2) I found that error before, Linda submit you the wrong report. She already re-submit the report. 3) The same as in my previsous e-mail. 4) Revised manual has been submited to you. 5) Revised SAR report has been submitted to you. By the way, Linda could not submit report to your web site, she might send it to your e-mail account later. Alan >From: Timothy R. Johnson [mailto:[email protected] ] >Sent: Monday, May 03, 2004 2:05 AM >To: [email protected] ...snip... >corporate fax: 703-847-6888 >Message has been scanned by Sporton AntiVirus System with no virus detected. From: "Alan Lane" <[email protected]> To: "'Timothy R. Johnson'" <[email protected]> Subject: RE: Review of Amigo Technology Co., Ltd.: RC6AWU-901W Page 1 of 1In 5/4/2004Printed for "Timothy R. Johnson" <[email protected]>

Hi, Tim, 1) No, we don't have. Normally, the signed back quotation form is the POA recognized by our customer. 2) We did submit it, but I will ask Linda to re-submit it again. 3) We did some similiar projects recently but never been requested for this. We did inform the customer for this requirement, but as usual, it is not possible to put such information in the users manual since they maybe will sell the product to different distributor. So, a separate sheet while they find a new buyer will be a better choice for them. Taking this chance, I would like to re-inform you just as I did before to Bill that I know your request is reasonable, but we could not ignore the fact the *****, ***** as well as *** never request such letter. That already become a big point that our customer can complain about. So, personally I think we can just do our job to inform the customer this requirement, and let them to do what they need to do instead of insisting to see the letter. 4) Revised manual will be submitted to you. 5) Revised report will be submitted to you. Alan -----Original Message----- >From: Timothy R. Johnson [mailto:[email protected] ] >Sent: Monday, May 03, 2004 2:04 AM >To: [email protected] >Subject: Review of Amigo Technology Co., Ltd.: RC6AWP-914W > > >Alan, > >Attached are comments regarding review of this application. > >Thank You, > >Timothy R. Johnson, NARTE Certified EMC Engineer (No. EMC-002205-NE) >Examining Engineer From: "Alan Lane" <[email protected]> To: "TimothyR. Johnson \(E-mail\)" <[email protected]> Subject: FW: Review of Amigo Technology Co., Ltd.: RC6AWP-914W Page 1 of 2In 4/4/2004file://C:\DOCUME~1\TIMJOH~1\LOCALS~1\Temp\eud164.htm >American TCB, Inc. >6731 Whittier Ave. >McLean, VA 22101 > >email: [email protected] >alternate email: [email protected] >mobile number: 404-414-8071 >corporate phone: 703-847-4700 >corporate fax: 703-847-6888 >Message has been scanned by Sporton AntiVirus System with no virus detected. > > >Attachment Converted: "c:\documents and settings\tim johnson\my documents\atcb folder\eudora\attach\ATCB Comment_043004.pdf" Page 2 of 2In 4/4/2004file://C:\DOCUME~1\TIMJOH~1\LOCALS~1\Temp\eud164.htm

APPENDIX A. Photographs of EUT

FCC ID: RC6AWU-901W Label Location

REPORT NO. : F432406 SPORTON International Inc. PAGE NUMBER : A1 OF A2 TEL : 886-2-2696-2468 ISSUED DATE : Apr. 23, 2004 FAX : 886-2-2696-2255 REPORT NO. : F432406 SPORTON International Inc. PAGE NUMBER : A2 OF A2 TEL : 886-2-2696-2468 ISSUED DATE : Apr. 23, 2004 FAX : 886-2-2696-2255

FCC ID: RC6AWU-901W Description of Operation EUT is a 802.11 b/ g USB Adapter with 11 channels. This device provided of transmitting speed 54Mbps . The device of RF carrier is QPSK. The device adapts Orthogonal Freguency Division Division Multipexing ( OFDM ). An embedded system can become RF enabled by inserting the RF module that interfaces to the embedded processor via USB interface . The antenna is chip Antenna, and there is no antenna connector . With embedded system becoming Wireless-enable by the wirless Modules, many wireless applications will become possible, such as: Communicate with each other wirelessly (between embedded systems, laptops, PCs, and others), including sharing or exchanges of data (i.e. wireless file transfers between wireless -enabled devices).

© 2003 SPORTON International Inc..SAR Testing Lab Page 0 of 29 This report shall not be reproduced except in full, without the written approval of Sporton. Rev.01 FCC SAR Test Report Test Report No ﹕ O432406-F Specific Absorption Rate (SAR) Test Report for Amigo Technology Co., Ltd. on the 802.11b+g wireless USB Dongle Report No. : O432406-F Brand Name : Amigo/ PTI Model Name : AWU-901W/ Wireless Pocket USB PTI-610G/ WLU2454 Date of Testing : Apr. 22, 2004 Date of Report : Apr. 27, 2004 Date of Review : Apr. 27, 2004 ‚ The test results refer exclusively to the presented test model / sample only. ‚ Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. SPORTON International Inc. 6F, No.106, Sec. 1, Hsin Tai Wu Rd., Hsi Chih, Taipei Hsien, Taiwan, R.O.C. ©2003 SPORTON International Inc..SAR Testing Lab Tel:886-22696-2468 Fax:886-2-2696-2255 FCC SAR Test Report Test Report No ﹕ O432406-F Table of Contents 1. Statement of Compliance ............................................................................................................................................................ 1 2. Administration Data ................................................................................................................................................................... 2 2.1. Testing Laboratory ............................................................................................................................................................. 2 2.2. Detail of Applicant ............................................................................................................................................................. 2 2.3. Detail of Manfacturer ......................................................................................................................................................... 2 2.4. Application Detail .............................................................................................................................................................. 2 3. Scope............................................................................................................................................................................................. 3 3.1. Description of Device Under Test (DUT) ........................................................................................................................... 3 3.2. Applied Standards: ............................................................................................................................................................. 5 3.3. Device Category and SAR Limits ....................................................................................................................................... 5 3.4. Test Conditons .................................................................................................................................................................... 6 3.4.1. Ambient Condition: ..................................................................................................................................................... 6 3.4.2. Test Configuration:...................................................................................................................................................... 6 4. Specific Absorption Rate (SAR) ................................................................................................................................................. 7 4.1. Introduction ........................................................................................................................................................................ 7 4.2. SAR Definition .................................................................................................................................................................... 7 5. SAR Measurement Setup............................................................................................................................................................ 8 5.1. DASY4 E-Field Probe System............................................................................................................................................. 9 5.1.1. ET3DV6 E-Field Probe Specification ....................................................................................................................... 10 5.1.2. ET3DV6 E-Field Probe Calibration .......................................................................................................................... 10 5.2. DATA Acquisition Electronics (DAE) ................................................................................................................................11 5.3. Robot ................................................................................................................................................................................ 12 5.4. Measurement Server ......................................................................................................................................................... 12 5.5. SAM Twin Phantom .......................................................................................................................................................... 12 5.6. Data Storage and Evaluation ........................................................................................................................................... 14 5.6.1. Data Storage .............................................................................................................................................................. 14 5.6.2. Data Evaluation ......................................................................................................................................................... 14 5.7. Test Equipment List ..............................................................................................................…

Text truncated - open the document above for the full version.

FCC ID: RC6AWU-901W Issued on Apr. 24, 2004 Report No.: F432406 SPORTON International Inc. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 FCC TEST REPORT CATEGORY : Portable End Product PRODUCT NAME : 802.11b+g wireless USB Dongle FCC ID. : RC6AWU-901W FILING TYPE : Certification BRAND NAME : Amigo, PTI MODEL NAME : 1. AWU-901W 2. Wireless Pocket USB 3. PTI-610G 4. WLU2454 APPLICANT : Amigo Technology Co., Ltd. No.6, Lane35, Jihu Rd., Neihu, Taipei, Taiwan 114, R.O.C. MANUFACTURER : Same as Applicant ISSUED BY : FAIR WAY ELECTRONICS FACTORY Huang Chong No.3 Ind Area, Zhong Tang Town, Dong Guan City, Guang Dong, P.R. China Statements: The test result in this report refers exclusively to the presented test model / sample. Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. Certificate or Test Report could not be used by the applicant to claim the product endorsement by CNLA, NVLAP or any agency of U.S. government. The test equipment used to perform the test are calibrated and traceable to NML/ROC or NIST/USA. Dr. Alan Lane Vice General Manager Sporton International Inc. Lab Code: 200079-0 1190 ILAC MRA FCC ID: RC6AWU-901W Issued on Apr. 24, 2004 Report No.: F432406 SPORTON International Inc. FCC ID. : RC6AWU-901W TEL : 886-2-2696-2468 Page No. : i FAX : 886-2-2696-2255 Issued Date : Apr. 24, 2004 Table of Contents History of this test report....................................................................................................................................ii 1. General Description of Equipment under Test.............................................................................................1 1.1. Applicant..........................................................................................................................................................................................1 1.2. Manufacturer ...................................................................................................................................................................................1 1.3. Basic Description of Equipment under Test ....................................................................................................................................1 1.4. Features of Equipment under Test..................................................................................................................................................1 1.5. Table for Carrier Frequencies .........................................................................................................................................................2 2. Test Configuration of the Equipment under Test.........................................................................................3 2.1. Description of the Test ....................................................................................................................................................................3 2.2. Frequency Range Investigated .......................................................................................................................................................3 2.3. Description of Test Supporting Units...............................................................................................................................................4 2.4. Connection Diagram of Test System ..............................................................................................................................................5 2.5. Test Software ..................................................................................................................................................................................6 3. Test Location and Standards .........................................................................................................................7 3.1. Test Location...................................................................................................................................................................................7 3.2. Test Conditions ...............................................................................................................................................................................7 3.3. Standards for Methods of Measurement .........................................................................................................................................7 3.4. DoC Statement................................................................................................................................................................................7 4. List of Measurements......................................................................................................................................8 4.1. Summary of the Test Results ..........................................................................................................................................................8 5. Test Result .......................................................................................................................................................9 5.1. Test of 6dB Spectrum Bandwidth ( DSSS System ) .......................................................................................................................9 5.2. Test of Maximum Peak Output Power ..........................................................................................................................................14 5.3. Test of Peak Power Spectral Density............................................................................................................................................16 5.4. Test of Band Edges Emission .......................................................................................................................................................21 5.5. Test of AC Power Line Conducted Emission ..............................................…

Text truncated - open the document above for the full version.

1.1.1. Photographs of Conducted Emission Test Configuration z The photographs show the configuration that generates the maximum emission. FRONT VIEW REAR VIEW 1.1.2. Photographs of Radiated Emission Test Configuration z The photographs show the configuration that generates the maximum emission. FRONT VIEW REAR VIEW