RPW-WLAN600WIRELESS IP PHONE

WLAN600 Wireless IP Phone User Guide Copyright Statement All brand names are registered trademarks of their respective companies. Disclaimer Products and specifications are subject to change without notice. NEV, 2003, Rev: 0.2 2 FEDERAL COMMUNICATIONS COMMISSION This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter This EUT is incompliance with SAR for general population /uncontrolled exposure limits in ANSI/IEEE C95.1-1999 and had been tested in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C 3 Contents 1. Introduction ..................................................................... 5 2. Getting Started................................................................ 6 2.1. Checking Shipment Completeness........................................... 6 2.2. Installing and Removing the Battery ........................................ 6 2.3. Charging the Battery ................................................................ 8 2.4. Keypad Definition of WLAN600 ................................................ 9 2.5. Turn on/off the Power ............................................................. 10 2.6. Setup to Default IP Address ................................................... 10 2.7. Switching the key-lock On/Off ................................................ 10 2.8. Adjusting the Speaker Volume ............................................... 11 3. Configuring Network Environment.................................12 3.1. Network Configuration ........................................................... 12 3.1.1. Setting Up/Modify to Static IP.......................................................................... 12 3.1.2. Setting UP/modify the DHCP Client............................................................... 14 3.1.3. Setting UP the PPPoE Settings........................................................................ 15 3.2. Wireless Configuration ........................................................... 17 3.2.1. Setting UP the Wireless Settings................................................................... 17 3.3. SIP Configuration .................................................................... 22 3.3.1. Setting UP the Proxy Server Settings.......................................................... 22 3.3.2. Setting UP the Outbound Proxy Settings.................................................... 24 3.3.3. Setting UP the User Account Settings......................................................... 25 3.4. SSL Configuration ................................................................... 27 3.5. Using the Phone Book ............................................................ 29 3.5.1. Searching Phone Book Entry: Speed Dial Key......................................... 29 3.5.2. Searching Phone Book Entry: Edit Entry.................................................... 30 3.5.3. Searching Phone Book Entry: Erase Entry................................................ 32 3.5.4. Searching Phone Book Entry: Group Setting............................................ 33 3.5.5. Adding a Phone Book Entry............................................................................... 34 3.5.6. Erasing Phone Book Entry: One by One...................................................... 35 3.5.7. Erasing Phone Book Entry: All......................................................................... 37 3.6. Using the Call History............................................................. 38 3.6.1. Missed Call................................................................................................................. 38 3.6.2. Received Call............................................................................................................. 40 4 3.6.3. Dialed Call................................................................................................................... 42 3.6.4. Erase Calls.................................................................................................................. 44 3.7. Setting..................................................................................... 46 3.7.1. Adjusting the Ring Volume................................................................................. 46 3.7.2. Setting the Ring Melody....................................................................................... 47 3.7.3. Setting the Vibrator …

Text truncated - open the document above for the full version.

FCC ID: RPW-WLAN600 Number 1 FRONT SIDE OF EUT FCC ID: RPW-WLAN600 Number 2 REAR SIDE OF EUT FCC ID: RPW-WLAN600 Number 3 CLOSER LOOK OF EARPHONE PORT OF EUT FCC ID: RPW-WLAN600 Number 4 CLOSER LOOK OF CHARGE CONNECTOR OF EUT FCC ID: RPW-WLAN600 Number 5 EARPHONE FCC ID: RPW-WLAN600 Number 6 FRONT SIDE OF BASE FCC ID: RPW-WLAN600 Number 7 REAR SIDE OF BASE FCC ID: RPW-WLAN600 Number 8 FRONT SIDE OF ADAPTER FCC ID: RPW-WLAN600 Number 9 REAR SIDE OF ADAPTER FCC ID: RPW-WLAN600 Number 10 LABEL OF ADAPTER

FCC ID: RPW-WLAN600 Label Location

FCC ID: RPW-WLAN600 Number 1 MECHANICAL CONSTRUCTION FCC ID: RPW-WLAN600 Number 2 MECHANICAL CONSTRUCTION FCC ID: RPW-WLAN600 Number 3 FRONT SIDE OF BATTERY FCC ID: RPW-WLAN600 Number 4 REAR SIDE OF BATTERY FCC ID: RPW-WLAN600 Number 5 MECHANICAL CONSTRUCTION FCC ID: RPW-WLAN600 Number 6 MECHANICAL CONSTRUCTION FCC ID: RPW-WLAN600 Number 7 FRONT SIDE OF MAIN BOARD FCC ID: RPW-WLAN600 Number 8 REAR SIDE OF MAIN BOARD FCC ID: RPW-WLAN600 Number 9 MECHANICAL CONSTRUCTION FCC ID: RPW-WLAN600 Number 10 REAR SIDE OF MAIN BOARD FCC ID: RPW-WLAN600 Number 11 FRONT SIDE OF PANEL FCC ID: RPW-WLAN600 Number 12 REAR SIDE OF PANEL FCC ID: RPW-WLAN600 Number 13 MECHANICAL CONSTRUCTION OF MODULE BOARD FCC ID: RPW-WLAN600 Number 14 FRONT SIDE OF MODULE BOARD FCC ID: RPW-WLAN600 Number 15 REAR SIDE OF MODULE BOARD FCC ID: RPW-WLAN600 Number 16 MECHANICAL CONSTRUCTIO N OF EARPHONE FCC ID: RPW-WLAN600 Number 17 FRONT SIDE OF MAIN BOARD OF EARPHONE FCC ID: RPW-WLAN600 Number 18 REAR SIDE OF MAIN BOARD OF EARPHONE FCC ID: RPW-WLAN600 Number 19 MECHANICAL CONSTRUCTIO N OF EARPHONE FCC ID: RPW-WLAN600 Number 20 FRONT SIDE OF VOICE CONTROL BOARD FCC ID: RPW-WLAN600 Number 21 REAR SIDE OF VOICE CONTROL BOARD FCC ID: RPW-WLAN600 Number 22 MECHANICAL CONSTRUCTION OF BASE FCC ID: RPW-WLAN600 Number 23 MECHANICAL CONSTRUCTION OF BASE FCC ID: RPW-WLAN600 Number 24 FRONT SIDE OF MAIN BOARD OF BASE FCC ID: RPW-WLAN600 Number 25 REAR SIDE OF MAIN BOARD OF BASE

©2003 SPORTON International Inc..SAR Testing Lab Tel:886-22696-2468 Fax:886-2-2696-2255 FCC SAR Test Report Test Report No ﹕ O3N2801-F Specific Absorption Rate (SAR) Test Report for BCM Communication Co., Ltd on the Wireless IP Phone FCC ID : .RPW-WLAN600 Report No. . : O3N2801-F Date of Testing. : Dec.09, 2003 and Jan. 29, 2004 Date of Report . : Jan. 30, 2004 Date of Review. : .Jan. 30, 2004 ‚ The test results refer exclusively to the presented test model/sample only. ‚ Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. SPORTON International Inc. 6F, No.106, Sec. 1, Hsin Tai Wu Rd., Hsi Chih, Taipei Hsien, Taiwan, R.O.C. ©2003 SPORTON International Inc..SAR Testing Lab Tel:886-22696-2468 Fax:886-2-2696-2255 FCC SAR Test Report Test Report No ﹕ O3N2801-F Table of Contents 1 .Statement of Compliance....................................................................................................................................................... 1 2. Administration Data..................................................................................................................................................................... 2 2.1 Testing Laboratory ................................................................................................................................................................ 2 2.2 Details of Applicant............................................................................................................................................................... 2 2.3 Application Details ................................................................................................................................................................ 2 3. General Information..................................................................................................................................................................... 3 3.1 Description of EUT ............................................................................................................................................................... 3 3.2 Applied Standards ................................................................................................................................................................. 6 3.3 Device Category and SAR Limits. ........................................................................................................................................ 7 3.4 Test Conditions................ ................................................................................................................................................. 7 3.4.1 Ambient Conditions ...................................................................................................................................................... 7 3.4.2 Test Configuration ........................................................................................................................................................ 7 4. Specific Absorption Rate (SAR)............................................................................................................................................... 8 4.1 Introduction ................................................................................................................................................................ 8 4.2 SAR definition....................................................................................................................................................................... 8 5. SAR Measurement System......................................................................................................................................................... 9 5.1 DASY4 E-Field Probe System-----------------------------------------------------------------------------------------------------------10 5.1.1 ET3DV6 E-Field Probe Specification --------------------------------------------------------------------------------------11 5.1.2 ET3DV6 E-Field Probe Calibration ----------------------------------------------------------------------------------------11 5.2 Data Acquisition Electronic (DAE) System--------------------------------------------------------------------------------------------12 5.3 Robot ----------------------------------------------------------------------------------------------------------------------------------------13 5.4 Measurement Server-----------------------------------------------------------------------------------------------------------------------13 5.5 SAM phantom------------------------------------------------------------------------------------------------------------------------------13 5.6 Device Holder for SAM Twin Phantom -----------------------------------------------------------------------------------------------15 5.7 Data Storage and Evaluation -------------------------------------------------------------------------------------------------------------16 5.7.1 Data Storage -------------------------------------------------------------------------------------------------------------------16 5.7.2 Data Evaluation -----------------------------------------------------------------------------------------------------------------16 5.8 Test Equipment List -----------------------------------------------------------------------------------------------------------------------19 6. Tissue Simulating Liquids......................................................................................................................................................... 20 7.Uncertainty Assessment.............. .............................................................................................................................................. 22 8. SAR Measurement Evaluation ..............................................................................................................................................…

Text truncated - open the document above for the full version.

©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F ©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F ©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F ©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F ©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F ©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F ©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F ©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F ©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F ©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F ©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F ©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F ©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F ©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F ©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F ©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F ©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F ©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F ©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F ©2003 SPORTON International Inc..SAR Testing Lab This report shall not be reproduced except in full, without the written approval of Sporton. Rev.00 FCC SAR Test Report Test Report No ﹕ O3N2801-F

FCC TEST REPORT Report No. : F3N2801 SPORTON International Inc. Page No. : 1 of 8 TEL : 886-2-2696-2468 Issued Date : Dec.10, 2003 FAX : 886-2-2696-2255 1.1. Comments6dB Emission bandwidth>500kHz -CH01 (802.11b) FCC TEST REPORT Report No. : F3N2801 SPORTON International Inc. Page No. : 2 of 8 TEL : 886-2-2696-2468 Issued Date : Dec.10, 2003 FAX : 886-2-2696-2255 -CH06 (802.11b) FCC TEST REPORT Report No. : F3N2801 SPORTON International Inc. Page No. : 3 of 8 TEL : 886-2-2696-2468 Issued Date : Dec.10, 2003 FAX : 886-2-2696-2255 -CH11 (802.11b) FCC TEST REPORT Report No. : F3N2801 SPORTON International Inc. Page No. : 4 of 8 TEL : 886-2-2696-2468 Issued Date : Dec.10, 2003 FAX : 886-2-2696-2255 1.2. Power Density -CH01 (802.11b) FCC TEST REPORT Report No. : F3N2801 SPORTON International Inc. Page No. : 5 of 8 TEL : 886-2-2696-2468 Issued Date : Dec.10, 2003 FAX : 886-2-2696-2255 -CH06 (802.11b) FCC TEST REPORT Report No. : F3N2801 SPORTON International Inc. Page No. : 6 of 8 TEL : 886-2-2696-2468 Issued Date : Dec.10, 2003 FAX : 886-2-2696-2255 -CH11 (802.11b) FCC TEST REPORT Report No. : F3N2801 SPORTON International Inc. Page No. : 7 of 8 TEL : 886-2-2696-2468 Issued Date : Dec.10, 2003 FAX : 886-2-2696-2255 1.3 Band Edges Measurement -CH01 FCC TEST REPORT Report No. : F3N2801 SPORTON International Inc. Page No. : 8 of 8 TEL : 886-2-2696-2468 Issued Date : Dec.10, 2003 FAX : 886-2-2696-2255 -CH11 (802.11b)

FCC TEST REPORT Report No. : F3N2801 SPORTON International Inc. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 FCC TEST REPORT for 47 CFR, Part 15, Subpart C Equipment : Wireless IP Phone Model No. : WLAN600 FCC ID : RPW-WLAN600 Filing Type : Certification Applicant : BCM Communication Co., Ltd 8F, No.3, Wolung Street, Taipei, Taiwan ‚ The test result refers exclusively to the test presented test model / sample. ‚ Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. ‚ Certificate or Test Report must not be used by the applicant to claim the product in this test report endorsement by NVLAP or any agency of U.S. government. SPORTON International Inc. 6F, No.106, Sec. 1, Hsin Tai Wu Rd., Hsi Chih, Taipei Hsien, Taiwan, R.O.C. FCC TEST REPORT Report No. : F3N2801 SPORTON International Inc. FCC ID RPW-WLAN600 TEL : 886-2-2696-2468 Page No. : i FAX : 886-2-2696-2255 Issued Date : Dec.10, 2003 Table of Contents History of this test report..................................................................................................................ii CERTIFICATE OF COMPLIANCE........................................................................................................................1 1. General Description of Equipment under Test.............................................................................................2 1.1. Applicant..........................................................................................................................................................................................2 1.2. Manufacturer ...................................................................................................................................................................................2 1.3. Basic Description of Equipment under Test ....................................................................................................................................2 1.4. Feature of Equipment under Test ...................................................................................................................................................3 2. Test Configuration of Equipment under Test ...............................................................................................5 2.1. Test Manner ....................................................................................................................................................................................5 2.2. Connection Diagram of Test System ..............................................................................................................................................6 3. Operation of Equipment under Test ..............................................................................................................7 4. General Information of Test............................................................................................................................8 4.1. Test Voltage ....................................................................................................................................................................................8 4.2. Standard for Methods of Measurement...........................................................................................................................................8 4.3. Test in Compliance with ..................................................................................................................................................................8 4.4. Frequency Range Investigated .......................................................................................................................................................8 4.5. Test Distance ..................................................................................................................................................................................8 5. Report of Measurements and Examinations ................................................................................................9 5.1. List of Measurements and Examinations ........................................................................................................................................9 5.2. 6dB Bandwidth ..............................................................................................................................................................................10 5.3. Maximum Peak Output Power ......................................................................................................................................................11 5.4. Power Spectral Density .................................................................................................................................................................12 5.5. Test of Conducted Emission .........................................................................................................................................................13 5.6. Test of Radiated Emission ............................................................................................................................................................21 5.7. Band Edges Measurement............................................................................................................................................................35 5.8. Antenna Requirements .................................................................................................................................................................36 6. EMI Suppression Component List ...............................................................................................................37 7. Antenna Factor & Cable Loss ......................................................................................................................38 8. List of Measuring Equipments Used ...................................................…

Text truncated - open the document above for the full version.

FCC TEST REPORT Report No. : F3N2801 SPORTON International Inc. FCC ID : RPW-WLAN600 TEL : 886-2-2696-2468 Page No. : 1 of 3 FAX : 886-2-2696-2255 Issued : Dec. 10, 2003 1.1. Photographs of Conducted Powerline Test Configuration z The photographs show the configuration that generates the maximum emission. FRONT VIEW REAR VIEW FCC TEST REPORT Report No. : F3N2801 SPORTON International Inc. FCC ID : RPW-WLAN600 TEL : 886-2-2696-2468 Page No. : 2 of 3 FAX : 886-2-2696-2255 Issued : Dec. 10, 2003 SIDE VIEW FCC TEST REPORT Report No. : F3N2801 SPORTON International Inc. FCC ID : RPW-WLAN600 TEL : 886-2-2696-2468 Page No. : 3 of 3 FAX : 886-2-2696-2255 Issued : Dec. 10, 2003 1.2. Photographs of Radiated Emission Test Configuration z The photographs show the configuration that generates the maximum emission. FRONT VIEW REAR VIEW