RYD-IBB683BBluetooth Boombox with PLL FM radio

AC power input: requires an AC/DC power adapter (included) LINE INUSB CHARGER DC IN 5V RESET IBB683B Bluetooth Boombox This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. :DUQLQJ&KDQJHVRUPRGL¿FDWLRQVWRWKLVXQLWQRWH[SUHVVO\DSSURYHGE\WKHSDUW\ responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‡Reorient or relocate the receiving antenna. ‡Increase the separation between the equipment and receiver. ‡Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‡ &RQVXOWWKHGHDOHURUDQH[SHULHQFHGUDGLR79WHFKQLFLDQIRUKHOS ‡ 7KHDSSDUDWXVVKDOOQRWEHH[SRVHGWRGULSSLQJRUVSODVKLQJDQGWKDWQRREMHFWV ¿OOHGZLWKOLTXLGVVXFKDVYDVHVVKDOOEHSODFHGRQDSSDUDWXV L’appareil ne doit pas être exposé aux écoulements ou aux éclaboussures et aucun objet ne contenant de liquide, tel qu’un vase, ne doit être placé sur l’objet. ‡Main plug is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected form the mains socket outlet completely. La prise du secteur ne doit pas être obstruée ou doit être facilement accessible pendant son utilisation. Pour être complètement déconnecté de l’alimentation d’entrée, la prise doit être débranchée du secteur. ‡ %DWWHU\VKDOOQRWEHH[SRVHGWRH[FHVVLYHKHDWVXFKDVVXQVKLQH¿UHRUWKHOLNH Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à la lumière du soleil, au feu ou autres choses de semblable. ‡Caution marking is located at the rear or bottom of the apparatus. Attention marquage est situé sur le paneau arrière ou inférieur de l’unité. ‡The marking information is located at the rear or bottom of apparatus. Le marquage est situé sur le paneau arrière ou inférieur de l’unité. 1.Read these Instructions. 2.Keep these Instructions. 3.Heed all Warnings. 4.Follow all instructions. 5.Do not use this apparatus near water. 6.Clean only with a dry cloth. 7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus LQFOXGLQJDPSOL¿HUV WKDWSURGXFHKHDW 9.Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug GRHVQRW¿WLQWR\RXURXWOHWFRQVXOWDQHOHFWULFLDQ for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, DQGWKHSRLQWZKHUHWKH\H[LWIURPWKHDSSDUDWXV 11.2QO\XVHDWWDFKPHQWVDFFHVVRULHV VSHFL¿HGE\WKHPDQXIDFWXUHU 12. Use only with a cart, stand, tripod, bracket, or table VSHFL¿HGE\WKHPDQXIDFWXUHURUVROGZLWKWKH apparatus. When a cart is used, use caution when PRYLQJWKHFDUWDSSDUDWXVFRPELQDWLRQWRDYRLGLQMXU\ from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. 13.5HIHUDOOVHUYLFLQJWRTXDOL¿HG service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus KDVEHHQH[SRVHGWRUDLQRU moisture, does not operate normally, or has been dropped. ‡CAUTION7235(9(17(/(&75,&6+2&.0$7&+:,'( %/$'(2)3/8*72:,'(6/27)8//<,16(57 ‡ :$51,1*7RUHGXFHWKHULVNRI¿UHRUHOHFWULFVKRFNGR QRWH[SRVHWKLVDSSDUDWXVWRUDLQRUPRLVWXUH ‡AVERTISSEMENT: Pour réduire le risque d’incendie ou de choc pOHFWULTXHQHSDVH[SRVHUFHWDSSDUHLOVRXVODSOXLHHWO¶KXPLGLWp ‡CAUTION: Use of controls or adjustments or performance of procedures RWKHUWKDQWKRVHVSHFL¿HGPD\UHVXOWLQKD]DUGRXVUDGLDWLRQH[SRVXUH ‡WARNING:&KDQJHVRUPRGL¿FDWLRQVWRWKLVXQLWQRWH[SUHVVO\DSSURYHGE\WKHSDUW\ responsible for compliance could void the user’s authority to operate the equipment. ‡ :$51,1*Do not place this unit directly onto furniture surfaces with any type of soft, porous, RUVHQVLWLYH¿QLVK$VZLWKDQ\UXEEHUFRPSRXQGPDGHZLWKRLOVWKHIHHWFRXOGFDXVHPDUNV or staining where the feet reside. We recommend using a protective barrier such as a cloth or a SLHFHRIJODVVEHWZHHQWKHXQLWDQGWKHVXUIDFHWRUHGXFHWKHULVNRIGDPDJHDQGRUVWDLQLQJ ‡WARNING:8VHRIWKLVXQLWQHDUÀXRUHVFHQWOLJKWLQJPD\FDXVHLQWHUIHUHQFH regarding use of the remote. If the unit is displaying erratic behavior move DZD\IURPDQ\ÀXRUHVFHQWOLJKWLQJDVLWPD\EHWKHFDXVH ‡ &$87,21'DQJHURIH[SORVLRQLIEDWWHU\LVLQFRUUHFWO\UHSODFHG Replace only with the same or equivalent type. ‡PRÉCAUTION: Danger d’explosion si les piles sont remplacées d…

Text truncated - open the document above for the full version.

Family models declaration letter 2013-6-9 We JETOP INDUSTRIAL LIMITED Of Unit 11, 2/F., Sing Win Factory Building, 15-17 Shing Yip Street, Kwun Tong, Kowloon (address) Declare under our sole responsibility that the product FCC ID: RYD-IBB683B Product: Bluetooth Boombox with PLL FM radio Model Number ：IBB683B, JT683 All models have the same constructions, circuit diagram and PCB layout. Only model name is different. Unless otherwise stated Thanks Sincerely, Cathie Lian/Manager E-mail: [email protected] Phone: 00852-25153978 Fax: 00852-25583209 Address: Unit 11, 2/F., Sing Win Factory Building, 15-17 Shing Yip Street, Kwun Tong, Kowloon, Hong Kong

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (current) 2.0 3.0 Jan-31-2012 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 3.0 JETOP INDUSTRIAL LIMITED 2013-6-9 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, JETOP INDUSTRIAL LIMITED hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): FCC ID: RYD-IBB683B (Bluetooth Boombox with PLL FM radio MODEL No.: IBB683B, JT683) We affirm that between SIEMIC and JETOP INDUSTRIAL LIMITED, any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Cathie Lian/Manager E-mail: [email protected] Phone: 00852-25153978 Fax: 00852-25583209 Address: Unit 11, 2/F., Sing Win Factory Building, 15-17 Shing Yip Street, Kwun Tong, Kowloon, Hongkong

Confidentiality Request Letter JETOP INDUSTRIAL LIMITED 2013-6-9 To: Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: Permanent Confidentiality Request for FCC ID: RYD-IBB683B We hereby request confidential treatment of information accompanying this application as outlined below: - Block diagram - Operation description - Schematic The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Cathie Lian/Manager E-mail: [email protected] Phone: 00852-25153978 Fax: 00852-25583209 Address: Unit 11, 2/F., Sing Win Factory Building, 15-17 Shing Yip Street, Kwun Tong, Kowloon, Hongkong

POWER SOURCEPAIRPLAY/PAUSEMEMORYTUNE +TUNE –VOLUMESCAN/CLK SET/ DISPLAY BATTERY LED LINE INUSB CHARGER DC IN 5V THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND 2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. FID: JT MODEL: IBB683B Bluetooth Boombox POWER SUPPLY : DC 5V 1500mA iLive, a brand of Digital Products International 2116 Carr Street, St. Louis, MO 63106 USA Made in China XXXXXXXXXX XX SERIAL NUMBER LABEL LOCATION RATING LABEL POSITION FCC ID: RYD-IBB683B RESET RAISE ENGRAVED 0.3MM RECESS ENGRAVE ALL SILKSCREEN COLOR IN P421C MODEL: IBB683B ITEM: SILKSCREEN DATE: 22 APR 2013

Bluetooth module Antenna

FCC ID : RYD-IBB683B RF EXPOSURE EVALUATION According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency(RF) Radiation as specified in §1.1307(b) Limits for Maximum Permissible Exposure(MPE) Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density(mW/cm 2 ) Average Time (A) Limits for Occupational/Control Exposures 300-1500 -- -- F/300 6 1500-100000 -- -- 5 6 (B) Limits for General Population/Uncontrol Exposures 300-1500 -- -- F/1500 6 1500-100000 -- -- 1 30 11.1 Friis transmission formula: Pd=(Pout*G)\(4*pi*R 2 ) Where Pd= Power density in mW/cm 2 Pout=output power to antenna in mW G= Numeric gain of the antenna relative to isotropic antenna Pi=3.1416 R= distance between observation point and center of the radiator in cm Pd the limit of MPE, 1mW/cm 2 . If we know the maximum gain of the antenna and total power input to the antenna, through the calculation, we will know the distance where the MPE limit is reached. 11.2 Measurement Result Antenna gain: 1dBi Modulation: GFSK Channel Channel Frequency (MHz) Output Peak power (dBm) Output Peak power (mW) Antenna Gain (dBi) Numeric Power density at 20cm (mW/ cm 2 ) Power density Limits (mW/cm 2 ) 1 2402 1.643 1.46 1.26 0.00037 1 40 2441 1.56 1.43 1.26 0.00036 1 79 2480 1.28 1.34 1.26 0.00034 1 Modulation: 1/4Π-DQPSK Channel Channel Frequency (MHz) Output Peak power (dBm) Output Peak power (mW) Antenna Gain (dBi) Numeric Power density at 20cm (mW/ cm 2 ) Power density Limits (mW/cm 2 ) 1 2402 -1.254 0.75 1.26 0.00019 1 40 2441 -1.352 0.73 1.26 0.00018 1 79 2480 -1.253 0.75 1.26 0.00019 1 Modulation: 8DPSK Channel Channel Frequency (MHz) Output Peak power (dBm) Output Peak power (mW) Antenna Gain (dBi) Numeric Power density at 20cm (mW/ cm2 ) Power density Limits (mW/cm2 ) 1 2402 -1.098 0.78 1.26 0.00019 1 40 2441 -1.203 0.76 1.26 0.00019 1 79 2480 -1.107 0.77 1.26 0.00019 1

TRF No：FCC 15.247/A Page 1 of 58 Report No: ES130416112E Shenzhen EMTEK Co.,Ltd. Building 69, Majialong Industry Zone, Nanshan District, Shenzhen,Guangdong,China www.emtek.com.cn Tel: +86-755-2695 4280 Fax: +86-755-2695 4282 Access to the World ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPARTC REQUIREMENT OF Bluetooth Boombox with PLL FM radio MODEL No.: IBB683B, JT683 FCC ID: RYD-IBB683B Tr a d e M ar k : GPX JT REPORT NO: ES130416112E ISSUE DATE: May 30, 2013 Prepared for JETOP INDUSTRIAL LIMITED Unit 11, 2/F., Sing Win Factory Building, 15-17 Shing Yip Street, Kwun Tong, Kowloon, Hong Kong Prepared by SHENZHEN EMTEK CO., LTD Bldg 69, Majialong Industry Zone, Nanshan District, Shenzhen, Guangdong, China TEL : 86-755-26954280 FAX: 86-755-26954282 TRF No：FCC 15.247/A Page 2 of 58 Report No: ES130416112E Shenzhen EMTEK Co.,Ltd. Building 69, Majialong Industry Zone, Nanshan District, Shenzhen,Guangdong,China www.emtek.com.cn Tel: +86-755-2695 4280 Fax: +86-755-2695 4282 Access to the World VERIFICATION OF COMPLIANCE Applicant: JETOP INDUSTRIAL LIMITED Unit 11, 2/F., Sing Win Factory Building, 15-17 Shing Yip Street, Kwun Tong, Kowloon, Hong Kong Manufacturer: SHENZHEN SHANGMEI ELECTRIC APPLIANCECO., LTD NO.9&11, LangHui Road,TangXia Yong Zone, Song'gang Town, Bao'an District, ShenZhen, Guandong, China Product Description: Bluetooth Boombox with PLL FM radio Model Number: IBB683B, JT683 (Note: all the models are the same, except their model number, we take IBB683B to test.) Trade Mark: GPX JT Serial Number: N/A File Number: ES130416112E Date of Test: April 16, 2013 to May 30, 2013 We hereby certify that: The above equipment was tested by SHENZHEN EMTEK CO., LTD. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 (2009) and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.247. The test results of this report relate only to the tested sample identified in this report. Date of Test : April 16, 2013 to May 30, 2013 Prepared by : Jack.Li/Editor Reviewer : King Wang/Supervisor Approve & Authorized Signer : Lisa Wang/Manager TRF No：FCC 15.247/A Page 3 of 58 Report No: ES130416112E Shenzhen EMTEK Co.,Ltd. Building 69, Majialong Industry Zone, Nanshan District, Shenzhen,Guangdong,China www.emtek.com.cn Tel: +86-755-2695 4280 Fax: +86-755-2695 4282 Access to the World Ta b l e o f C o n t e n t s 1 GENERAL INFORMATION ................................................................................................. 5 1.1 PRODUCT DESCRIPTION........................................................................................................................... 5 1.2 RELATED SUBMITTAL(S) / GRANT (S) ..................................................................................................... 5 1.3 TEST METHODOLOGY.............................................................................................................................. 5 1.4 SPECIAL ACCESSORIES............................................................................................................................ 5 1.5 EQUIPMENT MODIFICATIONS.................................................................................................................. 5 1.6 TEST FACILITY........................................................................................................................................ 6 2 SYSTEM TEST CONFIGURATION .................................................................................... 7 2.1 EUT CONFIGURATION............................................................................................................................. 7 2.2 EUT EXERCISE........................................................................................................................................ 7 2.3 TEST PROCEDURE.................................................................................................................................... 7 2.4 LIMITATION............................................................................................................................................. 7 2.6 EQUIPMENT USED IN TESTED SYSTEM................................................................................................... 11 2.7 DESCRIPTION OF TEST MODES................................................................................................................ 12 3 SUMMARY OF TEST RESULTS ....................................................................................... 13 4 CONDUCTED EMISSIONS TEST ..................................................................................... 14 4.1 MEASUREMENT PROCEDURE:................................................................................................................ 14 4.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ....................................................................... 14 4.3 MEASUREMENT EQUIPMENT USED: ...................................................................................................... 14 4.4 CONDUCTED EMISSION LIMIT.................................................................................................................. 14 4.5 MEASUREMENT RESULT:....................................................................................................................... 15 5 RADIATED EMISSION TEST ............................................................................................ 16 5.1 MEASUREMENT PROCEDURE................................................................................................................. 16 5.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ....................................................................... 17 5.3 MEASUREMENT EQUIPMENT USED: .................................…

Text truncated - open the document above for the full version.

Radiated Emission Test Conducted Emissions Test