RYK-WL760AWLAN 802.11a/b/g PCI Adapter

User’s Guide 1 Wireless Network Card Series User’s Guide Version 2.1 User’s Guide 2 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. If this device is going to be operated in 5.15 ~ 5.25GHz frequency range, then it is restricted in indoor environment only. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. SparkLAN declares that WL-760A ( FCC ID: RYK-WL760A ) is limited in CH1~CH11 for 2.4 GHz by specified firmware controlled in U.S.A. User’s Guide 3 Copyright statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording, or otherwise without the prior writing of the publisher. May 2005 User’s Guide 4 Contents 1. Introduction.............................................................................................................. 5 2. Wireless LAN Basics ............................................................................................... 6 3. Installation for Windows platform............................................................................. 7 3.1. Installation Overview............................................................................................. 8 3.2. Install Procedure for Windows .............................................................................. 9 3.3 Uninstall Procedure ............................................................................................. 14 4. Configuration Utility ............................................................................................... 15 4.1 Link Information ................................................................................................... 16 4.2 AP List ................................................................................................................. 18 4.3 Profile Setting ...................................................................................................... 19 4.4 About ................................................................................................................... 23 5. Appendix ............................................................................................................... 24 User’s Guide 5 1. Introduction Thank you for purchasing your Wireless LAN Adapter. This User’ s Guide will assist you with the installation procedure. The package you have received should contain the following items: • Wireless LAN Adapter • Quick Installation Guide • CD containing Wireless network adapter utility & drivers and User’s Guide Note: if anything is missing, please contact your vendor Note: This manual is valid for all Wireless LAN adapters, such as PC Card, USB, mini-USB, PCI adapter, mini-PCI...etc. User’s Guide 6 2. Wireless LAN Basics Wireless LAN (Local Area Networks) systems offer a great number of advantages over a traditional, wired system. Wireless LANs (WLANs) are more flexible, easier to setup and manage and often more cost effective than their wired equivalence. Using radio frequency (RF) technology, WLANs transmit and receive data over the air, minimizing the need for wired connections. Thus, WLANs combine data connectivity with user mobility, and, through simplified configuration, enable movable LANs. With wireless LANs, users can access shared information without looking for a place to plug in and network managers can set up or augment networks without installing or moving wires. Wireless LANs offer the following productivity, convenience and cost advantages over traditional wired networks: • Mobility - Wireless LAN systems can provide LAN users with access to real-time information anywhere in their organization. This mobility supports productivity and service opportunities not possible with wired networks. • Installation Speed and Simplicity - Installing a wireless LAN system can be fast and easy and can eliminate the need to pull cable through walls and ceilings. • Installation Flexibility - Wireless technology allows the network to go where wires cannot go. • Reduced Cost-of-Ownership - While the initial investment required for wireless LAN hardware might be higher than the cost of w…

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

FCC ID Label Location (FCC ID: RYK-WL760A)

WL-760A - Dual-Band 802.11a/b/g - High Speed 108Mbps Super mode Wireless PCI Adapter This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. Name: WL-760A Front lable Size: 102.5*27.5mm P/N: Materials : 5GHz 2.4GHz + + FCC ID : RYK-WL760A Tested to Comply With FCC Standards FOR HOME OR OFFICE USE Made inTaiwan 0560

Page 3 Page 4

FCC ID: RYK-WL760A Report No.RF940321L05A Technical Description The transmitter of the EUT (WLAN 802.11a/b/g PCI Adapter, 108Mbps Wireless PCI Adapter) is powered by host equipment. The antenna type used in this product is Dipole antenna with Reverse SMA antenna connector. Under normal use condition, the user has to keep at least 20cm separation distance between radiator and the body of the user. This device is a WLAN 802.11a/b/g PCI Adapter, which operates in both of the 5GHz and 2.4GHz bands and can not transmitting simultaneously, the maximum data rate could be 108Mbps. For more detailed instruction, please take a look at the user’s manual. FCC 15.407(c) states: The device shall automatically discontinue transmission in case of either absence of information to transmit or operational failure. These provisions are not intended to preclude the transmission of control or signaling information or the use of repetitive codes used by certain digital technologies to complete frame or burst intervals. Applicants shall include in their application for equipment authorization a description of how this requirement is met” Data transmission is always initiated by software, which is then pass down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets (ACKs, CTS, PSPoll, etc...) are initiated by the MAC. There are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets are being transmitted.

FCC ID: RYK-WL760A Report No.: RF940321L05A1Report Format Version 2.0.2 Reference No.: 940525L16 FCC TEST REPORT (15.247) REPORT NO.: RF940321L05A MODEL NO.: WL-760A OEM MODEL NO.: TEW-503PI TESTED: Mar. 10 ~ Mar. 23, 2005 ISSUED: May 28, 2005 APPLICANT: SparkLAN Communications, Inc. ADDRESS: 3Fl., No. 246, Sec. 1, Neihu Road., Neihu Chiu, Taipei Taiwan 114, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 116 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA FCC ID: RYK-WL760A Report No.: RF940321L05A2Report Format Version 2.0.2 Reference No.: 940525L16 Table of Contents 1.CERTIFICATION ......................................................................................................5 2.SUMMARY OF TEST RESULTS ..............................................................................6 2.1 MEASUREMENT UNCERTAINTY ...........................................................................6 3.GENERAL INFORMATION.......................................................................................7 3.1GENERAL DESCRIPTION OF EUT.........................................................................7 3.2DESCRIPTION OF TEST MODES...........................................................................8 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST ...................................................... 9 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL: ........................ 10 3.3GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................12 3.4DESCRIPTION OF SUPPORT UNITS ...................................................................12 4.TEST TYPES AND RESULTS (802.11b & g 2412~2462MHz BAND)....................13 4.1CONDUCTED EMISSION MEASUREMENT .........................................................13 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT....................................... 13 4.1.2 TEST INSTRUMENTS............................................................................................ 13 4.1.3 TEST PROCEDURES ............................................................................................ 14 4.1.4 DEVIATION FROM TEST STANDARD .................................................................. 14 4.1.5 TEST SETUP ......................................................................................................... 15 4.1.6 EUT OPERATING CONDITIONS ........................................................................... 15 4.1.7 TEST RESULTS ..................................................................................................... 16 4.2RADIATED EMISSION MEASUREMENT ..............................................................22 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT............................................ 22 4.2.2 TEST INSTRUMENTS............................................................................................ 23 4.2.3 TEST PROCEDURES ............................................................................................ 24 4.2.4 DEVIATION FROM TEST STANDARD .................................................................. 24 4.2.5 TEST SETUP ......................................................................................................... 25 4.2.6 EUT OPERATING CONDITIONS ........................................................................... 25 4.2.7 TEST RESULTS ..................................................................................................... 26 4.36dB BANDWIDTH MEASUREMENT .....................................................................34 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ................................................... 34 4.3.2 TEST INSTRUMENTS............................................................................................ 34 4.3.3 TEST PROCEDURE............................................................................................... 35 4.3.4 DEVIATION FROM TEST STANDARD .................................................................. 35 4.3.5 TEST SETUP ......................................................................................................... 35 4.3.6 EUT OPERATING CONDITIONS ........................................................................... 35 4.3.7 TEST RESULTS ..................................................................................................... 36 4.4MAXIMUM PEAK OUTPUT POWER .....................................................................44 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT...................... 44 4.4.2 INSTRUMENTS...................................................................................................... 44 FCC ID: RYK-WL760A Report No.: RF940321L05A3Report Format Version 2.0.2 Reference No.: 940525L16 4.4.3 TEST PROCEDURES ............................................................................................ 45 4.4.4 DEVIATION FROM TEST STANDARD .................................................................. 45 4.4.5 TEST SETUP ......................................................................................................... 45 4.4.6 EUT OPERATING CONDITIONS ........................................................................... 45 4.4.7 TEST RESULTS ..................................................................................................... 46 4.5POWER SPECTRAL DENSITY MEASUREMENT.................................................48 4.5.1 LIMITS OF P…

Text truncated - open the document above for the full version.

FCC ID: RYK-WL760A Report No.: RF940321L05A72Report Format Version 2.0.2 Reference No.: 940525L16 5. TEST TYPES AND RESULTS (802.11a 5725~5850MHz Band) 5.1 CONDUCTED EMISSION MEASUREMENT 5.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT FREQUENCY OF EMISSION (MHz)CONDUCTED LIMIT (dBμV) Quasi-peakAverage 0.15-0.5 0.5-5 5-30 66 to 56 56 60 56 to 46 46 50 NOTE:1. The lower limit shall apply at the transition frequencies. 1. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. 2. All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above. 5.1.2 TEST INSTRUMENTS DESCRIPTION & MANUFACTURERMODEL NO.SERIAL NO.CALIBRATED UNTIL Test Receiver ROHDE & SCHWARZ ESCS30100291Nov. 16, 2005 RF signal cable Woken 5D-FBCable-HYC01-01Jan. 09, 2006 LISN ROHDE & SCHWARZ ESH3-Z5100312Feb. 15, 2006 LISN ROHDE & SCHWARZ ESH2-Z5100104Feb. 15, 2006 Software ADT ADT_Cond_V3NANA NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room 1. 3. The VCCI Site Registration No. is C-2040. FCC ID: RYK-WL760A Report No.: RF940321L05A73Report Format Version 2.0.2 Reference No.: 940525L16 5.1.3 TEST PROCEDURES a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit – 20dB) was not recorded. 5.1.4 DEVIATION FROM TEST STANDARD No deviation FCC ID: RYK-WL760A Report No.: RF940321L05A74Report Format Version 2.0.2 Reference No.: 940525L16 5.1.5 TEST SETUP For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. 5.1.6 EUT OPERATING CONDITIONS Same as 4.1.6 FCC ID: RYK-WL760A Report No.: RF940321L05A75Report Format Version 2.0.2 Reference No.: 940525L16 5.1.7 TEST RESULTS Conducted Worst-Case Data EUT WLAN 802.11a/b/g PCI Adapter MODEL WL-760A CHANNEL Channel 3 6dB BANDWIDTH 9 kHz MODULATION TYPE BPSK TRANSFER RATE 6Mbps INPUT POWER (SYSTEM) 120Vac, 60 Hz PHASE Line (L) ENVIRONMENTAL CONDITIONS 20deg. C, 70%RH, 991hPa TESTED BYScott Yang Freq.Corr. Reading Value Emission Level LimitMargin NoFactor[dB (uV)][dB (uV)][dB (uV)](dB) [MHz](dB)Q.P.AV.Q.P.AV.Q.P.AV.Q.P.AV. 10.1920.1146.20-46.31-63.9653.96-17.65- 20.2550.1138.47-38.58-61.5851.58-23.00- 30.4460.1237.45-37.57-56.9646.96-19.39- 40.9560.1736.10-36.27-56.0046.00-19.73- 51.7830.2036.90-37.10-56.0046.00-18.90- 63.6290.2734.12-34.39-56.0046.00-21.61- 722.7261.0333.20-34.23-60.0050.00-25.77- *(The test data is in accordance with ADT Report No.: RF940321L05.) REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. FCC ID: RYK-WL760A Report No.: RF940321L05A76Report Format Version 2.0.2 Reference No.: 940525L16 EUT WLAN 802.11a/b/g PCI Adapter MODEL WL-760A CHANNEL Channel 3 6dB BANDWIDTH 9 kHz MODULATION TYPE BPSK TRANSFER RATE 6Mbps INPUT POWER (SYSTEM) 120Vac, 60 Hz PHASENeutral (N) ENVIRONMENTAL CONDITIONS 20deg. C, 70%RH, 991hPa TESTED BYScott Yang Freq.Corr. Reading Value Emission Level LimitMargin NoFactor[dB (uV)][dB (uV)][dB (uV)](dB) [MHz](dB)Q.P.AV.Q.P.AV.Q.P.AV.Q.P.AV. 10.1900.1043.93-44.03-64.0254.02-19.99- 20.3820.1140.77-40.88-58.2448.24-17.37- 30.6370.1339.66-39.79-56.0046.00-16.21- 40.8920.1638.24-38.40-56.0046.00-17.60- 51.2100.1938.32-38.51-56.0046.00-17.49- 63.5000.2636.34-36.60-56.0046.00-19.40- *(The test data is in accordance with ADT Report No.: RF940321L05.) REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. FCC ID: RYK-WL760A Report No.: RF940321L05A77Report Format Version 2.0.2 Reference No.: 940525L16 5.2 RADIATED EMISSION MEASUREMENT 5.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT Emissions radiated outside of the specified bands, shall be according to the general radiated limits in 15.209 as following: Frequencies (MHz) Field strength (microvolts/meter) Measurement distance (meters) 0.009-0.4902400/F(kHz)300 0.490-1.70524000/F(kHz)30 1.705-30.03030 30-881003 88-2161503 216-9602003 Above 9605003 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. FCC ID: RYK-WL760A Report No.: RF940321L05A78Report Format Version 2.0.2 Reference No.: 940525L16 5.2.2 TEST INSTRUMENTS DESCRIPTION & MANUFACTURER MODEL NO.SERIAL NO. CALIBRATED UNTIL Test Receiver ROHDE & SCHWARZ ESIB7100188Dec. 19, 2005 Spectrum Analyzer ROHDE & SCHWARZ FSP40100039Nov. 21, 2005 BILOG Anten…

Text truncated - open the document above for the full version.

FCC ID: RYK-WL760A Report No.: RF940321L05A1Report Format Version 2.0.2 Reference No.: 940525L16 FCC TEST REPORT (15.407) REPORT NO.: RF940321L05A MODEL NO.: WL-760A OEM MODEL NO.: TEW-503PI RECEIVED: NA TESTED: Mar. 10 ~ Mar. 23, 2005 ISSUED: May 28, 2005 APPLICANT: SparkLAN Communications, Inc. ADDRESS: 3Fl., No. 246, Sec. 1, Neihu Road., Neihu Chiu, Taipei Taiwan 114, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 72 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA FCC ID: RYK-WL760A Report No.: RF940321L05A2Report Format Version 2.0.2 Reference No.: 940525L16 Table of Contents 1.CERTIFICATION ......................................................................................................4 2.SUMMARY OF TEST RESULTS ..............................................................................5 2.1 MEASUREMENT UNCERTAINTY ...........................................................................5 3.GENERAL INFORMATION.......................................................................................6 3.1GENERAL DESCRIPTION OF EUT.........................................................................6 3.2DESCRIPTION OF TEST MODES...........................................................................7 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST ...................................................... 8 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL: .......................... 9 3.3GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................ 11 3.4DESCRIPTION OF SUPPORT UNITS ................................................................... 11 4.TEST TYPES AND RESULTS (5150 ~ 5350MHz band)........................................12 4.1CONDUCTED EMISSION MEASUREMENT .........................................................12 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT....................................... 12 4.1.2 TEST INSTRUMENTS............................................................................................ 12 4.1.3 TEST PROCEDURES ............................................................................................ 13 4.1.4 DEVIATION FROM TEST STANDARD .................................................................. 13 4.1.5 TEST SETUP ......................................................................................................... 14 4.1.6 EUT OPERATING CONDITIONS ........................................................................... 14 4.1.7 TEST RESULTS ..................................................................................................... 14 4.2RADIATED EMISSION MEASUREMENT ..............................................................17 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT............................................ 17 4.2.2 LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS .......... 18 4.2.3 TEST INSTRUMENTS............................................................................................ 19 4.2.4 TEST PROCEDURES ............................................................................................ 20 4.2.5 DEVIATION FROM TEST STANDARD .................................................................. 20 4.2.6 TEST SETUP ......................................................................................................... 21 4.2.7 EUT OPERATING CONDITION ............................................................................. 21 4.2.8 TEST RESULTS ..................................................................................................... 22 4.3PEAK TRANSMIT POWER MEASUREMENT .......................................................30 4.3.1 LIMITS OF PEAK TRANSMIT POWER MEASUREMENT..................................... 30 4.3.2 TEST INSTRUMENTS............................................................................................ 30 4.3.3 TEST PROCEDURE............................................................................................... 31 4.3.4 DEVIATION FROM TEST STANDARD .................................................................. 31 4.3.5 TEST SETUP ......................................................................................................... 31 4.3.6 EUT OPERATING CONDITIONS ........................................................................... 31 4.3.7 TEST RESULTS ..................................................................................................... 32 4.4PEAK POWER EXCURSION MEASUREMENT ....................................................41 4.4.1 LIMITS OF PEAK POWER EXCURSION MEASUREMENT.................................. 41 FCC ID: RYK-WL760A Report No.: RF940321L05A3Report Format Version 2.0.2 Reference No.: 940525L16 4.4.2 TEST INSTRUMENTS............................................................................................ 41 4.4.3 TEST PROCEDURE............................................................................................... 42 4.4.4 DEVIATION FROM TEST STANDARD .................................................................. 42 4.4.5 TEST SETUP ......................................................................................................... 42 4.4.6 EUT OPERATING CONDITIONS ........................................................................... 42 4.4.7 TEST RESULTS ..................................................................................................... 43 4.5PEAK POWER SPECTRAL DEN…

Text truncated - open the document above for the full version.

FCC ID: RYK-WL760A Report No.: RF940321L05A41Report Format Version 2.0.2 Reference No.: 940525L16 4.4 PEAK POWER EXCURSION MEASUREMENT 4.4.1 LIMITS OF PEAK POWER EXCURSION MEASUREMENT Frequency BandLimit 5.15 – 5.25 GHz13dB 5.25 – 5.35 GHz13dB 5.725 – 5.825 GHz13dB 4.4.2 TEST INSTRUMENTS Description & ManufacturerModel No.Serial No.Calibrated Until SPECTRUM ANALYZERFSEK30100049Aug. 12, 2005 NOTE: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. FCC ID: RYK-WL760A Report No.: RF940321L05A42Report Format Version 2.0.2 Reference No.: 940525L16 4.4.3 TEST PROCEDURE 1. The transmitter output was connected to the spectrum analyzer. 2. Set the spectrum bandwidth span to view the entire spectrum. 3. Using peak detector and Max-hold function for Trace 1 (RB=1MHz, VB=3MHz) and 2 (RB=1MHz, VB=300KHz). 4. The largest difference between Trace 1 and Trace 2 in any 1MHz band on any frequency was recorded. 4.4.4 DEVIATION FROM TEST STANDARD No deviation 4.4.5 TEST SETUP 4.4.6 EUT OPERATING CONDITIONS The software provided by client to enable the EUT under transmission condition continuously at specific channel frequencies individually. EUT SPECTRUM FCC ID: RYK-WL760A Report No.: RF940321L05A43Report Format Version 2.0.2 Reference No.: 940525L16 4.4.7 TEST RESULTS 802.11a OFDM modulation EUT WLAN 802.11a/b/g PCI Adapter MODEL WL-760A MODULATION TYPE BPSK TRANSFER RATE 6Mbps INPUT POWER (SYSTEM) 120Vac, 60 Hz ENVIRONMENTAL CONDITIONS 22deg.C, 55%RH, 991hPa TESTED BY Gary Chang CHANNEL CHANNEL FREQUENCY (MHz) PEAK POWER EXCURSION (dB) PEAK to AVERAGE EXCURSION LIMIT (dB) PASS/FAIL 151807.3513PASS 452407.5013PASS 552606.6813PASS 853207.3413PASS *(The test data is in accordance with ADT Report No.: RF940321L05.) FCC ID: RYK-WL760A Report No.: RF940321L05A44Report Format Version 2.0.2 Reference No.: 940525L16 CH1 CH4 FCC ID: RYK-WL760A Report No.: RF940321L05A45Report Format Version 2.0.2 Reference No.: 940525L16 CH5 CH8 FCC ID: RYK-WL760A Report No.: RF940321L05A46Report Format Version 2.0.2 Reference No.: 940525L16 802.11a Turbo OFDM modulation EUT WLAN 802.11a/b/g PCI Adapter MODEL WL-760A MODULATION TYPE BPSK TRANSFER RATE 12Mbps INPUT POWER (SYSTEM) 120Vac, 60 Hz ENVIRONMENTAL CONDITIONS 22deg.C, 55%RH, 991hPa TESTED BY Gary Chang CHANNEL CHANNEL FREQUENCY (MHz) PEAK POWER EXCURSION (dB) PEAK to AVERAGE EXCURSION LIMIT (dB) PASS/FAIL 152107.9313PASS 252508.1513PASS 352907.6613PASS *(The test data is in accordance with ADT Report No.: RF940321L05.) FCC ID: RYK-WL760A Report No.: RF940321L05A47Report Format Version 2.0.2 Reference No.: 940525L16 CH1 CH2 FCC ID: RYK-WL760A Report No.: RF940321L05A48Report Format Version 2.0.2 Reference No.: 940525L16 CH3 FCC ID: RYK-WL760A Report No.: RF940321L05A49Report Format Version 2.0.2 Reference No.: 940525L16 4.5 PEAK POWER SPECTRAL DENSITY MEASUREMENT 4.5.1 LIMITS OF PEAK POWER SPECTRAL DENSITY MEASUREMENT Frequency BandLimit 5.15 ~ 5.25GHz4dBm 5.25 ~ 5.35GHz11dBm 5.725 ~ 5.825GHz17dBm 4.5.2 TEST INSTRUMENTS Description & ManufacturerModel No.Serial No.Calibrated Until SPECTRUM ANALYZERFSEK30100049Aug. 12, 2005 NOTE: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. FCC ID: RYK-WL760A Report No.: RF940321L05A50Report Format Version 2.0.2 Reference No.: 940525L16 4.5.3 TEST PROCEDURES 1. The transmitter output was connected to the spectrum analyzer. 2. Set RBW=1MHz, VBW=3MHz. The PPSD is the highest level found across the emission in any 1MHz band. 4.5.4 DEVIATION FROM TEST STANDARD No deviation 4.5.5 TEST SETUP 4.5.6 EUT OPERATING CONDITIONS Same as 5.3.6 EUT SPECTRUM ANALYZER FCC ID: RYK-WL760A Report No.: RF9403…

Text truncated - open the document above for the full version.