RYK-WNFQ262ACNIBT802.11ac/b/g/n WiFi + Bluetooth M.2 Module

Wireless Module WNFQ-262ACNI(BT) Standards IEEE 802.11ac/a/b/g/n (2T2R) Bluetooth V5.0,V4.2,V4.1, V4.0 LE, V3.0+HS, V2.1+EDR Chipset Qualcomm Atheros QCA6174A-5 Data Rate 802.11b: 11Mbps / 802.11a/g: 54Mbps / 802.11n: MCS0~15/ 802.11ac: MCS0~9 Bluetooth: 1Mbps, 2Mbps and up to 3Mbps EDR Operating Frequency IEEE 802.11 ac/a/b/g/n ISM Band, 2400MHz~2483.5MHz, 5.150MHz~5.850MHz *Subject to local regulations Interface PCIe: WLAN; USB: Bluetooth Form Factor M.2 2242 B key Antenna 2xIPEX connector Ant 1 for WLAN Ant 2 for WLAN/BT Modulation 802.11b: DSSS (GFSK, DBPSK, DQPSK, CCK) 802.11a/g: OFDM (GFSK, BPSK, QPSK, 16-QAM, 64-QAM) 802.11n: OFDM (GFSK, BPSK, QPSK, 16-QAM, 64-QAM) 802.11ac: OFDM (GFSK, BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM) Power Consumption(Max.) TX: 610mA RX: 298mA Operating Voltage DC 3.3V Operating Temperature Range -40°C~85°C Storage Temperature Range -45°C~90°C Humidity (Non-Condensing) 5%~90% (Operating) 5%~90% (Storing) Wireless Module Dimension (in mm) 22mm x 42mm x2.78mm (±0.5mm) Weight (g) ≦ 6g Driver Support Windows 7/8.1/10 Linux (Open Source), Recommend Kernel v4.0+ Security 64/128-bits WEP, WPA, WPA2, 802.1x Wireless Module Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. FOR MOBILE DEVICE USAGE (>20cm/low power) Wireless Module Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module: KDB 996369 D03 OEM Manual v01 rule sections: 2.2 List of applicable FCC rules This module has been tested for compliance to FCC Part 15. 2.3 Summarize the specific operational use conditions The module is tested for standalone mobile RF exposure use condition. Any other usage conditions such as co-location with other transmitter(s) or being used in a portable condition will need a separate reassessment through a class II permissive change application or new certification. 2.4 Limited module procedures Not applicable. 2.5 Trace antenna designs Not applicable. 2.6 RF exposure considerations This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules. 2.7 Antennas The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module. The antenna must be installed such that 20 cm can be maintained between the antenna (refer to Page 11, Antenna Approved List) and users. Antenna Type Dipole Antenna connector RP-SMA Wireless Module 2.8 Label and compliance information The final end product must be labeled in a visible area with the following: “Contains FCC ID: RYK- WNFQ262ACNIBT. The grantee's FCC ID can be used only when all FCC compliance requirements are met. 2.9 Information on test modes and additional testing requirements This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) or portable use will require a separate class II permissive change re-evaluation or new certification. 2.10 Additional testing, Part 15 Subpart B disclaimer This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rule requirements if applicable. As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the eve…

Text truncated - open the document above for the full version.

FCC ID: RYK-WNFQ262ACNIBT Report No.: RF190610E05, RF190610E05-1, RF190610E05-2, RF190610E05-3, RF190610E05-4, RF190610E05-5, SA190610E05 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch February 7, 2020 Dear Application Examiner, SparkLAN Communications, Inc., Model: WNFQ-262ACNI(BT), FCC ID: RYK-WNFQ262ACNIBT would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of KDB996369 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip QCA6174A. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is QCA6174A. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a Convertible Board. Please see section Photographs of Test Configuration in the test report. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: RYK-WNFQ262ACNIBT Report No.: RF190610E05, RF190610E05-1, RF190610E05-2, RF190610E05-3, RF190610E05-4, RF190610E05-5, SA190610E05 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. P“The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Andrea Hsia Supervisor Bureau Veritas Consumer Products Services (H.K.) Ltd., Hsinchu Branch

Reference No.: 191031C13-1 Page No. 1 / 3 CONSTRUCTION PHOTOS OF EUT Reference No.: 191031C13-1 Page No. 2 / 3 Reference No.: 191031C13-1 Page No. 3 / 3

Label and Label location

Reference No.: 191031C13-2 Page No. 1 / 7 CONSTRUCTION PHOTOS OF EUT Reference No.: 191031C13-2 Page No. 2 / 7 Reference No.: 191031C13-2 Page No. 3 / 7 Ant. 1 Model: AD-305N Reference No.: 191031C13-2 Page No. 4 / 7 Ant. 2 Model: AD-300N Reference No.: 191031C13-2 Page No. 5 / 7 Ant. 3 Model: AD-103AG Reference No.: 191031C13-2 Page No. 6 / 7 Ant. 4 Model: AD-302N Reference No.: 191031C13-2 Page No. 7 / 7 Ant. 5 Model: AD-303N

Report No.: SA191031C13 Page No. 1 / 6 Report Format Version: 6.1.1 RF Exposure Report Report No.: SA191031C13 FCC ID: RYK-WNFQ262ACNIBT Test Model: WNFQ-262ACNI(BT) Received Date: Oct. 31, 2019 Test Date: Nov. 07 ~ Dec. 20, 2019 Issued Date: Jan. 09, 2020 Applicant: SparkLAN Communications, Inc. Address: 8F., No. 257, Sec. 2, Tiding Blvd., Neihu District, Taipei City 11493, Taiwan (R.O.C.) Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth ourfindings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: SA191031C13 Page No. 2 / 6 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 3 Calculation Result of Maximum Conducted Power ........................................................................... 6 Report No.: SA191031C13 Page No. 3 / 6 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued SA191031C13 Original release Jan. 09, 2020 Report No.: SA191031C13 Page No. 4 / 6 Report Format Version: 6.1.1 1 Certificate of Conformity Product: 802.11ac/b/g/n WiFi + Bluetooth M.2 Module Brand: SparkLAN Test Model: WNFQ-262ACNI(BT) Sample Status: R&D Sample Applicant: SparkLAN Communications, Inc. Test Date: Nov. 07 ~ Dec. 20, 2019 Standards: FCC Part 2 (Section 2.1091) References Test Guidance: IEEE C95.3 -2002 KDB 447498 D01 General RF Exposure Guidance v06 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date:Jan. 09, 2020 Celine Chou / Senior Specialist Approved by : , Date:Jan. 09, 2020 Bruce Chen / Senior Project Engineer Report No.: SA191031C13 Page No. 5 / 6 Report Format Version: 6.1.1 2 RF Exposure 2.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA191031C13 Page No. 6 / 6 Report Format Version: 6.1.1 3 Calculation Result of Maximum Conducted Power Frequency Band (MHz) Max Power (dBm) Antenna Gain (dBi) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) WLAN 2412-2462 23.77 8.01 20 0.300 1 5180-5240 22.59 8.54 20 0.258 1 5260-5320 22.44 8.54 20 0.249 1 5500-5720 23.06 8.54 20 0.288 1 5745-5825 22.45 8.54 20 0.250 1 Bluetooth LE 2402-2480 0.39 5.00 20 0.001 1 Bluetooth EDR 2402-2480 9.87 5.00 20 0.006 1 Note: Determining compliance based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. 2.4GHz: Directional gain = 5dBi + 10log(2) = 8.01dBi 5GHz: Directional gain = 5.53dBi + 10log(2) = 8.54dBi ---END---

Report No.: RF191031C13-3 Page No. 1 / 34 Report Format Version: 6.1.1 FCC Test Report Report No.: RF191031C13-3 FCC ID: RYK-WNFQ262ACNIBT Test Model: WNFQ-262ACNI(BT) Received Date: Oct. 31, 2019 Test Date: Nov. 28 ~ Dec. 19, 2019 Issued Date: Jan. 09, 2020 Applicant: SparkLAN Communications, Inc. Address: 8F., No. 257, Sec. 2, Tiding Blvd., Neihu District, Taipei City 11493, Taiwan (R.O.C.) Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF191031C13-3 Page No. 2 / 34 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ...................................................................................................................... 5 2 Summary of Test Results ..................................................................................................................... 6 2.1 Measurement Uncertainty ................................................................................................................... 6 2.2 Modification Record ............................................................................................................................ 6 3 General Information .............................................................................................................................. 7 3.1 General Description of EUT ................................................................................................................ 7 3.2 Description of Test Modes ................................................................................................................... 8 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................. 9 3.3 Duty Cycle of Test Signal .................................................................................................................. 10 3.4 Description of Support Units .............................................................................................................. 11 3.4.1 Configuration of System under Test ................................................................................................... 11 3.5 General Description of Applied Standards and References .............................................................. 11 4 Test Types and Results ...................................................................................................................... 12 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 12 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 12 4.1.2 Test Instruments ................................................................................................................................ 13 4.1.3 Test Procedures ................................................................................................................................. 14 4.1.4 Deviation from Test Standard ............................................................................................................ 14 4.1.5 Test Setup .......................................................................................................................................... 15 4.1.6 EUT Operating Conditions ................................................................................................................. 16 4.1.7 Test Results ....................................................................................................................................... 17 4.2 Conducted Emission Measurement .................................................................................................. 22 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 22 4.2.2 Test Instruments ................................................................................................................................ 22 4.2.3 Test Procedures ........................................................................................................…

Text truncated - open the document above for the full version.

Report No.: RF191031C13 Page No. 1 / 55 Report Format Version: 6.1.1 FCC Test Report Report No.: RF191031C13 FCC ID: RYK-WNFQ262ACNIBT Test Model: WNFQ-262ACNI(BT) Received Date: Oct. 31, 2019 Test Date: Nov. 07 ~ Dec. 19, 2019 Issued Date: Jan. 09, 2020 Applicant: SparkLAN Communications, Inc. Address: 8F., No. 257, Sec. 2, Tiding Blvd., Neihu District, Taipei City 11493, Taiwan (R.O.C.) Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF191031C13 Page No. 2 / 55 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ...................................................................................................................... 5 2 Summary of Test Results ..................................................................................................................... 6 2.1 Measurement Uncertainty ................................................................................................................... 6 2.2 Modification Record ............................................................................................................................ 6 3 General Information .............................................................................................................................. 7 3.1 General Description of EUT ................................................................................................................ 7 3.2 Description of Test Modes ................................................................................................................... 8 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................. 9 3.3 Duty Cycle of Test Signal .................................................................................................................. 10 3.4 Description of Support Units .............................................................................................................. 11 3.4.1 Configuration of System under Test ................................................................................................... 11 3.5 General Description of Applied Standards and References .............................................................. 11 4 Test Types and Results ...................................................................................................................... 12 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 12 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 12 4.1.2 Test Instruments ................................................................................................................................ 13 4.1.3 Test Procedures ................................................................................................................................. 14 4.1.4 Deviation from Test Standard ............................................................................................................ 14 4.1.5 Test Setup .......................................................................................................................................... 15 4.1.6 EUT Operating Conditions ................................................................................................................. 16 4.1.7 Test Results ....................................................................................................................................... 17 4.2 Conducted Emission Measurement .................................................................................................. 31 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 31 4.2.2 Test Instruments ................................................................................................................................ 31 4.2.3 Test Procedures ..............................................................................................................…

Text truncated - open the document above for the full version.

Reference No.: 191031C13 Page No. 1 / 5 PHOTOGRAPHS OF THE TEST CONFIGURATION Conducted Emission Test Reference No.: 191031C13 Page No. 2 / 5 Radiated Emission Test (Above 1GHz) Reference No.: 191031C13 Page No. 3 / 5 Radiated Emission Test (Below 1GHz) Reference No.: 191031C13 Page No. 4 / 5 Reference No.: 191031C13 Page No. 5 / 5 DFS Set UUT as Client without radar detection mode (Radar injected into Master) Master Radar ( Radiated ) UUT Receiver Antenna to S.A.