S9ZTEW430APB-C802.11g Wireless LAN Access Point

i Regulatory notes and statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions however are far much less than the electromagnetic energy emissions from wireless devices like for example mobile phones. Wireless LAN devices are safe for use frequency safety standards and recommendations. The use of Wireless LAN devices may be restricted in some situations or environments for example: ·On board of airplanes, or ·In an explosive environment, or ·In case the interference risk to other devices or services is perceived or identified as harmful In case the policy regarding the use of Wireless LAN devices in specific organizations or environments (e.g. airports, hospitals, chemical/oil/gas industrial plants, private buildings etc.) is not clear, please ask for authorization to use these devices prior to operating the equipment. Regulatory Information/disclaimers Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The Manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, of the substitution or attachment. Manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failing to comply with these guidelines. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause ii harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help . FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. We declare that the product is limited in CH1~CH11 by specified firmware controlled in the USA. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. iii TABLE OF CONTENT About This Guide .......................................................................................................................... 1 Purpose........................................................................................................................................ 1 Overview of this User’s Guide ...................................................................................................1 Unpacking and Setup..................................................................................................................... 2 Unpacking ................................................................................................................................... 2 Setup ........................................................................................................................................... 2 Hardware Instalation...................................................................................................................... 3 Front panel .................................................................................................................................. 3 Rear Panel ................................................................................................................................... 3 Hardware connections ................................................................................................................ 4 Connect to the Switch/Hub ......................................................................................................4 Check the installation............................................................................................................... 4 Configuring the Wireless LAN Access Point................................................................................ 6 Login to the Wireless AP through WLAN ................................................................................. 6 Login ........................................................................................................................................... 6 Main Screen of the Access Point ................................................................................................7 Wizard...............................................................................................................…

Text truncated - open the document above for the full version.

FCC ID: S9ZTEW430APB-C Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, ___________________________________ Wen Tsai / Sr. Product Manager TRENDware International Inc. TEL.: (310)626-6252 FAX: (310)626-6267 [email protected] 3135 Kashiwa Street, Torrance, CA 90505 United States TEL.: (310)626-6252 FAX: (310)626-6267

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

FCC ID: S9ZTEW430APB-C Label Location

MADE IN xxxxxx This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference and (2)this device must accept any interference received, including interference that may cause undesired operation. FCC ID: S9ZTEW430APB-C 59.00 mm CAYYWW50XXXXX TEW-450APB H/W:A2.1R MAC: XXXXXXXXXXXX/#

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3 Page 4

FCC ID: S9ZTEW430APB-C Report No.: RF941229L04B Operational Description This device is a 802.11g Wireless LAN Access Point which operates in the 2.4GHz frequency spectrum with throughput of up to 54Mbps which OFDM technique will be applied. If the signal to noise radio is too poor which could not support 54Mbps, the 11Mbps data rate with CCK technique will be applied. The transmitter of the EUT is powered by AC Adapter. The antenna is Dipole antenna with SMA reverse antenna connector. For more detailed instruction, please take a look at the user’s manual.

Report No.: RF941229L04B1Report Format Version 2.0.4 Reference No.: 950616L22 FCC TEST REPORT REPORT NO.: RF941229L04B MODEL NO.: TEW-430APB RECEIVED: May 10, 2006 TESTED: Dec. 15, 2005 ~ Jan. 03, 2006 May 10 ~ 12, 2006 (for conducted emission and radiated emission below 1GHz test) ISSUED: Jun. 20, 2006 APPLICANT: TRENDware International Inc. ADDRESS: 3135 Kashiwa Street, Torrance, CA 90505 United States ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: 47 14 th Lin, Chiapau Tsun, Linko, Taipei, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Kueishan, Taoyuan, Taiwan, R.O.C. This test report consists of 61 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF941229L04B2Report Format Version 2.0.4 Reference No.: 950616L22 Table of Contents 1CERTIFICATION.............................................................................................................4 2SUMMARY OF TEST RESULTS...................................................................................5 2.1MEASUREMENT UNCERTAINTY.................................................................................5 3GENERAL INFORMATION.............................................................................................6 3.1GENERAL DESCRIPTION OF EUT..............................................................................6 3.2DESCRIPTION OF TEST MODES................................................................................7 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST...........................................................7 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL................................8 3.3GENERAL DESCRIPTION OF APPLIED STANDARDS.............................................10 3.4DESCRIPTION OF SUPPORT UNITS........................................................................10 4TEST TYPES AND RESULTS.......................................................................................11 4.1CONDUCTED EMISSION MEASUREMENT...............................................................11 4.1.1LIMITS OF CONDUCTED EMISSION MEASUREMENT............................................11 4.1.2TEST INSTRUMENTS..................................................................................................11 4.1.3TEST PROCEDURES..................................................................................................12 4.1.4DEVIATION FROM TEST STANDARD........................................................................12 4.1.5TEST SETUP...............................................................................................................13 4.1.6EUT OPERATING CONDITIONS.................................................................................13 4.1.7TEST RESULTS...........................................................................................................14 4.2RADIATED EMISSION MEASUREMENT....................................................................20 4.2.1LIMITS OF RADIATED EMISSION MEASUREMENT.................................................20 4.2.2TEST INSTRUMENTS.................................................................................................21 4.2.3TEST PROCEDURES..................................................................................................22 4.2.4DEVIATION FROM TEST STANDARD........................................................................22 4.2.5TEST SETUP...............................................................................................................23 4.2.6EUT OPERATING CONDITIONS.................................................................................23 4.2.7TEST RESULTS...........................................................................................................24 4.36dB BANDWIDTH MEASUREMENT...........................................................................31 4.3.1LIMITS OF 6dB BANDWIDTH MEASUREMENT........................................................31 4.3.2TEST INSTRUMENTS.................................................................................................31 4.3.3TEST PROCEDURE....................................................................................................32 4.3.4DEVIATION FROM TEST STANDARD........................................................................32 4.3.5TEST SETUP...............................................................................................................32 4.3.6EUT OPERATING CONDITIONS.................................................................................32 4.3.7TEST RESULTS...........................................................................................................33 4.4MAXIMUM PEAK OUTPUT POWER..........................................................................39 4.4.1LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT..........................39 4.4.2TEST INSTRUMENTS.................................................................................................39 4.4.3TEST PROCEDURES..................................................................................................40 4.4.4DEVIATION FROM TEST STANDARD........................................................................40 4.4.5TEST SETUP...............................................................................................................40 4.4.6EUT OPERATING CONDITIONS.................................................................................40 Report No.: RF941229L04B3Report Format Version 2.0.4 Reference No.: 950616L22 4.4.7TEST RESULTS...........................................................................................................41 4.5P…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST